Search Documents

To improve a miner's chances for survival in an emergency by providing an improved self-rescuer device that functions in a toxic or oxygen-deficient atmosphere. The Approach: Development of a compact, lightweight apparatus which produces oxygen by using the wearer's breath in a chemical reaction. How It Works: The device is designed to cause the user's breath, which contains water vapor and carbon dioxide, to react with potassium superoxide (K02) to produce oxygen in quantities sufficient to sustain the wearer for one hour. The system is a closed circuit and does not depend on "screening" of noxious gases. To use the device, the miner opens the top and

Jan 1, 1974

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By Thomas Novak, Robert Goldstein

The analysis of a machine-luminaire configuration is a time- consuming process requiring the construction of a machine mockup, installation of a designated lighting arrangement, and an extensive set of illumination measurements. This entire process, however, is well suited to computer analysis. By simulating the machine geometry and the characteristics of the desired luminaires, the incident light levels can be calculated at the required set of points. This Bureau of Mines paper presents a general description of the techniques involved in performing this simulation.

By Sidney Katell

This cost bibliography, covering the period from January through December 1960, is a continuation of the series which began with the publication of Information Circular 7516 in October 1949. It is also the second report in the series to be prepared as a cooperative effort by the Bureau of Mines and the American Association of Cost Engineers. The cooperative agreement between the two groups provides for the publication of an annual bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, came from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal. Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil.

Jan 1, 1961

By James M. Spear

Sample results suggest the only mineral resources in the study areas are placer gold deposits along the South Fork Kern River in the Woodpecker RARE II unit (fig. 1). These deposits, in Rockhouse Basin, total 4.5 Figure 1.--NEAR HERE. million cu yds (3.4 million cu m) of indicated subeconomic gold resources in four deposits of "older" gravel. Gold value in samples averages $0.36 per cu yd ($0.47 par cu m) and is as much as $4.44 per cu yd 1/. Cost of mining the gravel and recovering the placer gold is estimated to be more than $2 per cu yd ($2.62 per cu m) for a deposit of this size and type. Additional inferred subeconomic placer gold resources with similar grade probably occur in four other deposits of "older" gravel on which no mining claims were located. Placer gold occurrences on upper Trout Creek contain gold worth as much as $4.50 per cu yd ($5.88 per cu m) 1/. Average grade is much lower, and only about 1,000 cu yds remain (760 cu m). These occurrences do not constitute a resource, but may attract hobbyists not dependent upon making a profit.

Jan 1, 1982

By R. Burrell, N .. L. Lapp

"Except for asthma and pulmonary infections, the types of lung disease that have been of immunologic interest the longest are the various mineral pneumoconioses. Because of their chronicity, type of pathology produced, and well-known immunotoxic properties associated with the dusts inciting them, the pneumoconioses have long drawn attention to the possibility that the immune system has not only been modulated but that its effectors have possibly contributed to their pathogenesis. All of the mineral dusts reviewed here have definite immunomodulating properties and act on various cellular and molecular components of the immune system. Further, each has an immunotoxic potential to induce either hypersensitivity (as in the case of beryllium) or other types of immune injury. This article reviews the immunologic aspects of the four major occupational minerals that have an immunologic impact on the lung: asbestos (particularly chrysotile), silica or quartz, beryllium, and coal mine dust.These agents have many things in common, yet each is distinctive. Although the possibility still exists that these mineral particles can adsorb intrinsic tissue antigens or extrinsic organic antigens to their surfaces and initiate immune responses to the adsorbed antigens, only one, beryllium, can act as an antigen itself. Silica is a profound macrophage toxin and thereby exerts many effects on those factors controlled by macrophages. Asbestos has undergone the most immunologic studies resulting in a much dearer picture of how it may contribute to immunopathology. Coal mine dust is the agent about which least is known immunologically, partly because there is no such thing as purified coal mine dust or a standard by which coal mine dust can be defined. Indeed, there are studies that use only the dust from the ground coal itself, whereas other studies use the total dust collected from air samples of a working mine in the belief that other types of dusts (e.g., silica from roof bolt drilling, from sand ground on the rails by cars, and from surface drilling) contribute to the disease (Figs. 1 to 5). This properly is coal mine dust and is poorly characterized. Yet, workers exposed to these dusts share similar reactive characteristics and they may be considered collectively as well as individually."

Mar 1, 1992

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By G. S. Scott

In the course of the investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, some attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rice if the rate of generation of heat exceeds the rate of brat dissipation and will fall if the opposite is the case. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By G. L. Fitzpatrick

A portable optical instrument for performing multispot laser vibrometry is described. The instrument is capable of measuring arrival times, surface motion frequency, and surface velocity and displaying these quantities in various useful ways. Sigma Research is currently pursuing the development of such optical measuring systems for the evaluation of structures in rock by non-contact interferometry methods. This work was sponsored by the U.S. Department of Interior (U.S. Bureau of Mines) under a Small Business Innovation Research (SBIR) contract number J0145075. The goal of the work was to develop a portable tripod mounted measuring system which can be set up at arbitrary distances (up to 30 meters) from a surface and project four in-line laser sample beams on this surface. A light receiving telescope gathers the scattered light from these four spots and provisions are made to mix this light with a reference beam from the laser. Four photodiodes are employed to determine the resultant interference signals which characterize the motion (particle velocity, frequency, amplitude) of the four illuminated spots on the surface under sudy. Information of this type can then be used to characterize the elastic or mechanical properties of the surface in question. In some cases (if more than four spots are involved) this surface information could be back propagated to draw inferences about the internal state of the material volume bounded by this surface.

Jan 1, 1987

By Robert W. Ageton

The Bureau of Mines is currently conducting a comprehensive study to evaluate all aspects of recovering gold from large, low-grade deposits in the Golden Sunlight area, Whitehall mining district, Jefferson County, Mont. Prior to World War II this area produced significant quantities of gold. The study includes geologic mapping, diamond drilling, assaying, computer analysis of assay data, metallurgical research and ore testing, mine and mill planning, and an economic evaluation of all factors bearing on the establishment of a producing gold mine. Preliminary evaluation of the deposit indicates about 31 million tons of submarginal gold resources. American Exploration and Mining Co. (AMEX) has assisted the Bureau in this project by providing drill site preparation, control assays, and geological aid for the Bureau's exploration work and by furnishing comprehensive assay information of the property and copies of base and geologic maps. This report presents the geology and mining history of the area, together with a summary of Bureau work in progress.

Jan 1, 1969

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was clone through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will he useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetimes. This report is in two volumes: Volume l - Technical Report Volume 2 - Design, Inspection, and Maintenance Manual

Jan 1, 1977

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By G. S. Scott

In the course of tire investigation into the causes, behavior, and control of mine fires, which the Bureau of Mines is now conducting, come attention was given to the subject of spontaneous heating. It is self-evident that the temperature of a pile of broken coal will rise if the rate of generation of heat exceeds the rate of heat dissipation and will fall if the opposite is the cane. Factors that affect the rate of generation of heat are:

Jan 1, 1941

By D. J. Parker

The oft-repeated expression that the taproot of safety lies in the attitude of the management toward accident-prevention work is indisputable and has become almost an axiom. Trite and somewhat timeworn though the statement may be, it is nevertheless true that the supervisory force must earnestly support a policy of safety and maintain at all times a con¬ siderate regard for the welfare of the employee if that high degree of cooperation of the employee, so vital to the successful prosecution of any safety program, is to be expected. The responsibility for preventing accidents rests upon the management, and in the case of the Spring Canyon Coal Co. such responsibility is recognized and accepted with little or no reservation. This company, aside from the humanitarian aspects involved, believes that safety is good business and not a matter to be treated passively or in a perfunctory manner. The problems with respect to safety that have been met and wholly or partly solved can best be appreciated when some of the natural conditions, adverse and otherwise, existing at this operation are taken into consideration. Mine 1 is about 1 mile north of the town of Spring Canyon, Carbon County, Utah, and is served by both the Denver & Rio Grande Western and Utah Coal Route railways. During the year 1931 the mine produced 312,397 tons, approximately 10 per cent being derived from pillar workings. The normal daily output during the summer months is about 2,000 tons, and during the peak of production in the winter season the daily production varies from 2,500 to 3,000 tons. The number of miners varies from 87 in summer to 220 in winter, and the day men vary in number from 66 in the winter to 45 in the summer; 12 company men are employed the year around. The officers of the company are J. B. Smith, president, San Francisco, California; T. R. Stockett, general manager, Salt Lake City; and G. A. Murphy, superintendent, David Brown, assistant superintendent, and John Sullivan, mine foreman, all of Spring Canyon, Utah.

Dec 1, 1932

By R. V. Ramani

This volume, the first of a six volume final report, provides an executive summary of the research and results carried out under a grant from the U. S. Bureau of Mines on underground coal mine ventilation. Under the project, a mine ventilation simulator was developed. Sensitivity of leakage and friction factors on the total quantity and pressure requirements was studied. The simulator was applied to a new mine under development, and to an operating mine, to demonstrate the usefulness of the simulator in ventilation planning and in evaluating proposed changes to existing ventilation system. The titles of the other volumes are as follows: Volume II: Mine Ventilation Network Theory Volume III: User's Manual for PSU/MVS Volume IV: Sensitivity of Leakage and Friction Factors Volume V: Application of PSU/MVS to Ventilation Planning of a New Mine Volume VI: Application of PSU/MVS to the Analysis of Modifications to Existing Ventilation Systems

Jan 1, 1977

By D. H. Desy

The Bureau of Mines has conducted research on the ignition of methane-air mixtures by sparks caused by frictional impact of aluminum alloys on rusted steel at typical coal mine fan speeds. The objectives were to establish the incendivity of aluminum alloys under these conditions, to investigate differences between aluminum alloys, and to evaluate substitute materials for the aluminum-steel combination. With a specially designed apparatus, three commercial aluminum casting alloys and a number of experimental aluminum alloys were tested for incendivity of the frictional impact against rusted steel in flammable methane-air mixtures. All aluminum alloys tested produced some ignitions. Of the experimental alloys, the harder alloys and those containing silicon tended to be more incendive than the others. With the normal experimental conditions, constructional steel, stainless steel, brass, and plastic did not cause ignition of methane-air mixtures in frictional impact against rusted steel. Some ignitions occurred with constructional steel at high speed in more flammable gas mixtures enriched with oxygen. From these findings, it is suggested that constructional material combinations other than the aluminum-steel combustion would minimize this inc endive hazard. A detailed description is given of previous research, and comparison is made with present results where appropriate.

Jan 1, 1975

By Steven W. Schmauch

The Ruby Mountains study area encompasses 75,615 acres managed by the U.S. Bureau of Land Management in Madison County, MT. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine mineral resources. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. There are no organized mining districts and no current claims in the study area. Significantly mineralized quartz veins, shear zones, or talc bodies apparently do not exist within the study area. A small part of the Kelly Iron Deposit is inside, but dips away from the study area; the main occurrence is estimated to have 32 million tons of subeconomic resources that average 21 percent iron.

Jan 1, 1985

By Michael J. Beus, Stephen Iverson

BACKGROUND A mine shaft is the lifeline to underground mines. Mine operators depend on safe, uninterrupted, and efficient movement of workers and materials. The shaft and hoisting system provides access to the network of openings used to recover the underground resource, provides vertical transport of miners and materials, and serves as an escapeway in case of an emergency. Accidents involving hoisting can be catastrophic. Such was the case in 1973 at the Markham Colliery in Derbyshire, UK when the conveyance overwound and fell to the shaft bottom, resulting in 17 deaths. Hoist and elevator machinery must meet the requirements specified in the Code of Federal Regulations (CFR), Parts 57 and 75. According to the Mine Safety and Health Administration (MSHA) data, many shaft-related accidents in the United States are associated with the hoisting cycle. MSHA statistics show that there were about 1500 shaft- related accidents in the 5-year period between 1992-1996. Most of these accidents resulted from the action, motion, or failure of the hoisting equipment or mechanism and involved movement of the conveyance which includes cages, skips, ore buckets, and elevators. A hoisting hazard may be characterized as an "unsafe hoist operating condition caused by insufficient or inaccurate information available to the hoist operator" (authors' quote). Earlier investigators have defined safety features and operating and maintenance standards for hoists, and reported on monitoring and control systems and sensors for hoists and conveyances [Farley, 1983; Ward, 19931. However, despite the considerable technological progress and hoisting control improvements in recent years, safety- related issues that require further investigation still remain. The hoist operator must constantly be aware of two important hoist-operating conditions: the position of the conveyance and the tension in the hoist rope. If this information is not available or is inaccurate, the hoist becomes unsafe. Current technology provides this information indirectly from sensors and indicators in the hoist room. However, unlike a building elevator hoistway, mine shaft hoistway problems often include: 1. poor ground conditions and excessive shaft wall and guide displacement; 2. rock bursts in deep mines (resulting in large rock movements and fragments blocking the hoist way); 3. water, ice, and salt buildup (impeding the smooth flow of the conveyance); 4. severe vibration from hoisting (resulting in loose guide support brackets, broken welds, or other alignment and conveyance mechanism malfunctions). The second issue relates to dynamic rope loads applied during normal winding, particularly during loading, acceleration, and stopping. Safety factors on wire rope are based on static load. They are artificially high to account for all cases of dynamic loads, even though the total load history on the rope (static and dynamic) during service is unknown. Therefore the tension, and thus the compliance with wire rope load safety factors, is unknown to the hoistman.

By Dong G. Chae

A model for the leaching of oxide ores is developed and II correlated with laboratory tests for percolation leaching of copper oxide are. Using the model, recovery of metal values and lixiviant concentration of the effluent solution at any time may be evaluated. For the copper oxide ore a simplified version of the model is examined for the leaching mechanism consisting of: 1) a surface flush reaction with the highest rate of lixiviant consumption; 2) penetration of lixiviant to react with copper minerals and gangue constituents; and, 3) slow lixiviant consumption, mostly by residual gangue materials. The simplified model is able to explain reasonably the leaching behavior of copper oxide ore by introducing a concept of effective initial size to correct for packing in a bed of fine particles.

Jan 1, 1979

By B. S. Covino

The Bureau of Mines has conducted a laboratory and field corrosion test¬ing program to determine materials of construction for the leaching and gas-sparging crystallization environments of the clay-HC1 process in order to more fully utilize the alumina from domestically available kaolinitic clays. Laboratory tests were used to determine the corrosion rates of 22 metals and alloys by weight-loss measurements in these two environments of the process. The results of this laboratory study were used both to suggest metals and alloys for field testing and to determine the effect of the individual solution components on the corrosion behavior of the metals and alloys. Results from the field tests were used to recommend Ta, Ta-2.5W, and Ta-10W for con¬struction of the agitators for the leaching process. The metals and alloys recommended for construction of the gas-sparging crystallizer heat exchangers were Ta, Ta-2.5W, Ta-10W, Nb, Nb-1Zr, Nb-3Zr, Nb-28Ta-10W-1Zr, Nb-10Hf-1Ti, and Zr for the first stage and Ta, Ta-2.5W, Ta-10W, Nb-28Ta-10W-1Zr, Nb, Nb-10Hf-1Ti, and Zr for the second stage.

Jan 1, 1981