Search Documents

By L. A. Neumeier

The Bureau of Mines investigated hot-rolling and forging characteristics of experimental ductile iron castings, both sand and permanent-mold, made with charges containing up to 70 pct foundry pig iron and 95 pct steelmaking pig iron. Between 1,550° and 1,950° F, most castings could be rolled to 90-pct reduction or forged to 70-pct reduction without serious cracking. Charge and composition have less bearing on workability than on subsequent properties. Permanent mold castings could be worked as readily as sand castings at 1,750° and 1,950° F. Plasticity improved with temperature. Small billets were also forged cold to 50-pct reduction without cracking. With equivalent nodularity, composition affects properties of wrought materials by altering matrix structure and strength. Properties vary with reduction and improve with increasing working temperature. Rolled material has high strength and anisotropy, and low ductility, particularly in the trans-verse direction. Annealing reduces strength and improves ductility, but anisotropy persists. At 70-pct reduction, impact resistance in the longitudinal direction is about twice that in the transverse. Annealing roughly doubles impact resistance. Deformation enhances damping capacity. The feasibility of die-forging and bar-rolling of ductile iron was evaluated in trial tests conducted under a Bureau contract. Although workability and ductility of ductile iron are inferior to those of steel, more advantage could be taken of ductile iron's plasticity to work rough shapes to final dimensions.

Jan 1, 1980

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By Harry Dobroski

Communications with moving tracked vehicles in a rail haulage mine pose a difficult problem. These communications take place from dispatcher to vehicles or from vehicle to vehicle via the trolley line, which is a very poor communications line. As a result, deadspots and high-signal areas can occur anywhere along the line, or signal can decrease simply as a function of distance. An analysis is made of the trolley line as a communications line, and methods of improving its characteristics are discussed. Data from inmine experiments are presented, showing actual improvements in communications. Recent Bureau developments in new hardware are also discussed. These include an adaptive speaker control for existing carrier phones and a new generation of improved carrier phones.

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract S0122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine.

Jan 1, 1974

By G. R. Hopkins

Crude-petroleum pipe lines in the United States on May 1, 1941, had a total length of 118,350 miles - an increase of 7,770 miles since Jun, 30, 1936, then the last previous survey was made by the Bureau of Mines. The expansion was due almost entirely to trunk-line construction, as the mileage of gathering lines was virtually unchanged from 1936. The greatest mileage of gathering lines, 53,640, was recorded in the survey of May 1, 1931. Both trunk and gathering-line mileage decreased moderately, in the interval from 1531 to 1936, but the present survey indicates that trunk-line facilities have expanded since 1936 to new high levels. Truck-line mileage equaled 55 percent of the total mileage of all crude lines on May 1, 1941, and 52 percent is 1936. The total length of gasoline pipe lines on May 1, 1941, was 9,001 miles this does not include several hundred miles of life under construction at that time or several hundred additional miles now being laid. No detailed surveys of gasoline mileage were made for 1, 1931, and June 30, 1936, but the mileage for those dates was about 1,400 and 4,600, respectively.

Jan 1, 1941

By Walter B. Lenhart

This paper is one of a series on milling methods and costs being. published by the Bureau of Mines. The milling practices and special problems relating to grinding, tailings disposal, and choice of a treatment process at the Cardinal mill are discussed. The property of the Cardinal Gold Mining Co. is about 18 miles southwest of the town of Bishop, Inyo County, Calif., at an altitude of approximately 8,500 feet. The camp has been designated Bishop Creek by the postal authorities. The property comprises 33 mining claims, including fractions and millsite in sections 19, 20, 29, and 30, T. 8 S., R. 31 E. These claims are located in a general way along the strike of a band of quartzite.

Jan 1, 1938

By Clive Ellis, Brian Davies, Steven E. Mischler, Jon C. Volkwein

A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclusion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air. A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclu­sion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air.

This report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the ore handling stream. Oversize ore causes much additional labor, creating work stoppages and is a principal cause of accidents in metal mines. This report includes data on block caving, back cut and fill room and pillar, shrinkage stoping, and sublevel stoping.

Jan 1, 1974

By M. M. Fine

The flotation work on samples from nine fluorspar properties in Crittenden and Livingston Counties, Ky., reported herewith was part of a wartime project that resulted in increasing the supply of metallurgical-grade fluorspar. The samples were tailings, dumps, and waste rock that had been rejected in previous milling operations. All were treated successfully by flotation to yield metallurgical-grade concentrates with recoveries ranging from 77.5 to 98.3 percent of the fluorite. After the laboratory testing, the results of which were available to the owners and operators of the properties, many of the tailing ponds and rock dumps were milled. The real value of this report, therefore, is to show the operators of gravity concentration plants the possibilities of re-treating waste products by flotation either at some future time or currently with the gravity

Jan 1, 1948

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

The following Inventory was prepared to provide mineral deposit data to the U.S. Army Corps of Engineers for use in the Resource Development Navigation Study in Alaska. The inventory was prepared using data contained in the U.S. Bureau of Mines Minerals Availability System (MAS) database. The Alaska portion of the database contains Information on over 7,000 mineral locations and deposits throughout the state. When MAS was established In 1975, database entries were originally compiled from literature searches by both Bureau personnel and contractors. Deposit data are obtained/maintained through Information gained from a variety of sources, Including published and unpublished Bureau of Mines reports, records, and files; U.S. Geological Survey (USGS) Bulletins, Professional Papers, and other reports; technical and professional Journals; State and other Federal agency publications; data generated during field examinations; and information obtained from knowledgeable individuals. Because of the size of the data base, many of the data have not been significantly modified since initial entry. Each deposit on the MAS data base has a sequence number of the following form:

Jan 1, 2011

By R. L. Rickel

The Bureau of Mines, as part of its minerals environmental technology research, conducted a study of mine waste tailings disposal. Part of the investigation evaluated the sand bed dewatering technique for disposal of alumina mini plant tailings as a means to increase consolidation rates and contain effluents. The technique employs a bed of sand resting on an impervious bottom. The tailings slurry is impounded over the sand layer and is dewatered through bottom drain piping. The study employed a single 10-ft-high, 6-in-diam, clear polyvinyl-chloride (PVC) column, and thickener wastes from the acid leaching of calcined kaolin clay. Results showed a consolidation rate of 41 in in 186 days for a total volume reduction of 37 pct. Sand bed dewatering was an efficient technique for solid consolidation and effluent containment when compared with data obtained from other dewatering studies.

Jan 1, 1982

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By Terry R. Neumann

During 1984, at the request of the U. S. Bureau of Land Management, U.S. Bureau of Mines personnel conducted a mineral survey of the 28,600-acre South Pahroc Range Wilderness Study Area (NV-050-0132). The Wit derness Study Area is located in Lincoln County, NV, about 900 miles north of Las Vegas. Five mineral properties and two mineralized zones were examined during this study; of these, one mineralized zone, two small prospect pits, and part of two claims are within Wilderness Study Area boundaries. Perlite resources were identified in the study area; however, no significant metallic mineral values were noted at any of the sites. The Wilderness Study Area is dominated by a Tertiary volcanic sequence consisting of an interlayered series of tuffs containing thin beds of volcanic pebble gravel, sandstone, and perlite. At the base of the exposed volcanic section, perlite occurs along a 2.4-mile-long zone that parallel s the study area's northeastern boundary. The perlite is suitable for filtration, insulation, and soil conditioning purposes, Because of prohibitive operation and transportation costs, the estimated 6 million tons of perlite occurring inside the South Pahroc Range Wilderness Study Area are classified as an indicated subeconomic resource.

Jan 1, 1986

By D. E. Traut

A fluidized, countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines in support of its objective to help assure an adequate uranium supply for future national needs. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous, except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid-leach-uranium solution and a strong-base, ion-exchange resin was studied, together with subsequent elution using an acidified sodium chloride solution. The effects of the number of compartments, compartment height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. Also examined were the kinetic and equilibrium relationships for the absorption and elution steps. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The columns system was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By Forrest T. Moyer

The overall disabling work injury experience, excluding office- workers, at nometal mines and mills during the period 1961-63, as reported to the Bureau of Mines by operators, was 77 fatal and 7,201 nonfatal injuries during an aggregate worktime of 335,029,685 man- hours. These injuries, fatal and nonfatal combined, occurred at a frequency rate of 21.72 per million man-hours, comprising 0.23 for the fatal and 21.49 for the nonfatal injuries. The combined severity rate of the disabilities was 2,312 days lost or charged per million man-hours, consisting of 1,379 for the fatal and 933 of the nonfatal injuries, The average severity of all disabilities during 1961-63, was 106 days per injury, The number of days lost or charged, excluding officeworkers, at nonmetal mines and mills during 1961-63, was 462,000 days charged to fatal injuries and 312,461 days lost from nonfatal injuries. The outstanding causes for fatal injuries were explosions (18 fatalities occurred in a major mine-explosion disaster in a potash mine in Utah in 1963) and falls of rock or ore from back or side, while most nonfatal injuries were caused by handling materials, slips or falls of persons, haulage, and machinery. The parts of the body most frequently injured during the period 1961-63 were the trunk, hand and finger, and foot and toe, An average of 52,810 men were at work daily, There were 20 nonfatal disabling injuries reported for office- workers at nonmetal mines and mills during the period 1961-63 during an aggregate worktime of 23,088,496 man-hours, These injuries occur- red at a frequency rate of 0.87 per million man-hours, There were no fatal injuries reported.

Jan 1, 1967

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical Studies have been prepared for the Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which wee may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to-noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna configurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by N BS. The recent NBS data is that used by Collins in the final predictions.

Jan 1, 1974

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection and operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939