Search Documents

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although eliminating hazardous noise is the long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use is usually quite different (i.e., worse) than when tested under lab conditions. In addition, workers may refuse to wear their hearing protection for any number of reasons. This project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis on optimizing the balance between effectiveness, comfort, over protection, and communication ability. The recently completed auditory research facility is now under-going the accreditation process conducted by the National Institute of Standards and Technology under the National Voluntary Laboratory Accreditation Program. Experiments are planned to investigate the factors that affect a miner’s ability to hear hazard and warning sounds (e.g., roof working, alarm signals, spoken communications, etc.). A service contract has been initiated to record and digitally store samples of typical warning sounds heard in an underground coal mine. This information will be analyzed in the lab to develop recommendations that can be offered to the mining community regarding correct earplug/earmuff usage to maximize there cognition of hazard and warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2001

By William E. Sopper

Heat-dried municipal sludge was applied to a barren burned anthracite refuse bank in 1974. Sludge was applied at rates of 0, 40, 75, and 150 dry metric tons per hectare" Ten species of trees were planted and five species of grasses and legumes were seeded for evaluation. One plot was also irrigated with sewage effluent. The 150 t/ha sludge application rate produced the best overall herbaceous vegetation growth response. The 40 and 75 t/ha sludge application rates produced the best tree seedling growth response. Foliar analyses for trace metals indicated no phytotoxity problems. Analyses of leachate water at the three-foot soil depth indicated that the sludge applications did not impair water quality. Results of the study indicate that treated municipal sludge can be used to revegetate land disturbed by mining activities without adverse effects on the vegetation or water quality.

Jan 1, 1978

By Terry J. Close

A mineral resource survey of the 236-mil (611-km2) Hyalite-Porcupine-Buffalo Horn wilderness study area (RARE 11 Areas No. 1-155 G, Gallatin Divide; and H, Hyalite) between the Gallatin and Yellowstone rivers in Montana, indicates there are phosphate rock and petrified wood resources (fig. 1). The area also has some potential for oil, gas, and geothermal resources. Stone and alluvium are abundant but appear to have little potential for development because other sources are available nearer to markets.

Jan 1, 1981

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973

By J. S. Hansen

To advance technology that can conserve critical materials, the Bureau of Mines investigated a cast-on hard-surfacing that wear resistance and confines alloy additions to wear-prone surfaces. Wear-resistant material in form is on a polystyrene , the is embedded in a mold of unbonded s and the wear-resistant material is transferred to a cas surface at the time of For low-stress abrasion, derived from high-carbon ferro-chrome had higher wear resistance than did commercially available weld-hard. The microstructure of the was typi-white iron carbides. Free carbon added to the ferrochrome powder produced more M7C3 carbides than did material contained in surfacings made from ferrochrome alone, and improved the wear resistance. Several white iron powders with greatly reduced chromium contents also white iron contain-M7C3 carbides. One derived from white iron powder had wear resistance to that of weld-deposited hard facings. Among the parameters investigated, surfacing thickness was found to have a or influence on diffusion of elements out of the , microstructure, and wear resistance. The results of field tests on bucket-wheel excavator teeth and plowshares with cast-on hard surfacing are given.

Jan 1, 1985

By Gerald A. Munson, E. P. Barrett

Rapid and accurate estimation of the proportions of mineral in rock mix- tures is essential in mineral-dressing research and industrial operation. Estimation of the proportions of potash and soda feldspars in ground pegmatite material by casual observation is almost impossible and may be tedious or even difficult by petrographic examination. Chemical analysis may not be an accurate measure, as pegmatite rock may contain the following minerals:

Jul 1, 1947

This article updates the status of fatalities occurring in both coal and metal/nonmetal mines from January through December of 2001. Based on preliminary accident reports, as of December 31, 2001, seventy-two fatalities have occurred at coal and metal/ nonmetal mining operations. During this period, forty-two fatalities occurred at coal operations and thirty fatalities occurred at metal/nonmetal operations. Ignition or explosion of gas or dust and fall of roof were the most frequent accident classifications in coal and powered haulage fatalities were the most frequent accident classification in metal/nonmetal.

Jan 1, 2002

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983

By Jerry E. Olson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 20,071-acre South Fork Wilderness Study Area (OR-005-033) and part of the 8,791-acre Sand Hollow Wilderness Study Area (OR-005-034) in order to evaluate their identified mineral resources. The study areas are located in Crook County, OR, about 58 air miles east from Bend. The areas studied are underlain by Tertiary- and Quaternary-age volcanic and tuffaceous sedimentary rocks. No mineral resources were identified in or adjacent to the study area. Except for common opal and agate occurrences along the northern boundary of the study areas, no mines, prospects, or mineralized zones occur within the study areas. Bentonite is periodically mined less than 1 mi southwest of the Sand Hollow study area boundary. Neither of the study areas has geothermal leases, but both areas are under lease for oil and gas.

Jan 1, 1987

By M. Beus, R. Iverson, A. Dreschler, V. Scott

This paper describes research to improve safety during transport of ore and waste in underground mines. Field tests are underway in mines in Idaho and Montana. Strains measured on structural support members in an ore pass provided information about total forces acting on the structure as material was dumped into it. Results show that measured static loads were considerably less than actual total weight of the material dumped and that dynamic loads were subject to many factors, such as effects of blasting to remove hang-ups. Comparisons of measurements and computer results using a particle flow code indicated that several difficulties remain before achieving realistic determinations and models of the dynamic effects of particle flow in ort: passes and impact loads on the gates. Impact loads were overestimated in computer analyses as compared to loads measured in field tests. An alternative design approach based on softening the chute and control gate assembly is being proposed.

By Charles D. Litton

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 2010

By Richard H. Spencer, Thomas E. Doerfler, Robert L. Lagace, James M. Dobbie, William S. Hawes

This report assesses the expected detectability, on the surface above mines, of electromagnetic signals produced in the frequency band of 630 to 3030 Hz by a rescue transmitter activated by miners trapped underground. This assessment is based on a statistical analysis of experimental signal and noise data taken at a representative sample of coal mine sites well distributed over the United States underground coal fields. Regression analyses are performed to characterize the signal transmission behavior of overburdens as a function of depth and frequency. The predicted signal behavior is then combined with experimentally based distributions of the background noise, and aural detection characteristics of signals in noise, to generate curves of the expected probability of detection for trapped miner signals versus overburden depth and operating frequency. The implications of these results, and associated recommendations, are presented regarding the detectability of trapped miners, sensitivity analyses and confirmatory tests, and operational utilization considerations for the trapped miners and the search and rescue team on the surface.

Jan 7, 1980

The above referenced contract between Badger Manufacturing Corporation and the U. S Bureau of Mines was executed June 30, 1975, as a result of the request for proposals for innovative machine concepts. We selected the cutting machine category because of the obvious lack of technical progress in this field for many years: Phase I of the contract required blasting fragmentation tests to determine proper blasting patterns for use with the auger-type kerf cutting machine. Phase II required design concept development for a machine capable of cutting a circular void as an aid to blasting.

Jan 1, 1975

By JOEL H. SWARTZ

During a series of resistivity measurements carried out in 1929 and 1930 a number of questions arose concerning the effect of topography on the character of the curves and the depths attained , the ratio of true depth to certain radii interpreted as representing depth , etc. To answer these questions it was decided to undertake a series of experimental investigations on artificial strata . It is the purpose of the present paper to present the results of the studies thus undertaken .

Feb 1, 1931

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1980 was $328.6 million, a decrease of $7.8 million from 1979. Cement, crushed stone, lime, clays, and sand and gravel continued as the major commodities produced. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, ferroalloys, kaolin, and oyster shell; fourth in dimension marble, masonry cement, and bentonite; and fifth in fire clay and lime. Alabama ranked in the top 20 States in total value of non-metallic minerals produced. Adverse economic conditions in the construction and metals industries impacted on the minerals industry in Alabama. Mineral producers supplying raw or finished materials to these industries experienced periodic reductions in sales during the year. Unit price increases did not keep up with inflation.

Jan 1, 1982

By Oliver Bowles

The mineral asbestos, because of its unique fibrous character, is allied to cotton and wool but has the advantage of heat and fire resistance; therefore, it supplies many industrial needs for which no substitutes are yet available. This report covers the essential features of the asbestos industry, including occurrence, production, mining, milling, utilization, international trade, and marketing. The United States leads all countries in the manufacture of asbestos products, but domestic sources furnish only a small fraction of the raw material required. As the United States is dependent to so great an extent on foreign supplies of raw materials, the bulletin deals at length with the asbestos industry in foreign lands. Several reports now available deal with the industry in individual countries. Among them are Chrysotile Asbestos in Canada, by J. G. Ross; Asbestos in the Union of South Africa, by A. L. Hall; and a series of articles on the Russian industry, by Walter A. Ru Keyser. These have been drawn upon freely, and full acknowledgment is hereby made for the helpful information thus secured. The file of the magazine Asbestos also has furnished many valuable data touching all phases of the industry. Many other books and articles listed in the bibliography at the end of this bulletin have been utilized and have been supplemented by the author's intimate acquaintance with the industry for about 20 years. The intent is to present a concise, world-wide, historical, technical, and economic treatment of the asbestos industry.

Jan 1, 1937

By W. L. Zeigler

This paper describing the milling practice of the Hecla Mining Co. is one of a series being prepared by the United States Bureau of Mines. The concentrator of the Hecla Mining Co., which utilizes combined gravity and flotation methods, is located at Gem, Shoshone County, Idaho, about 2 miles south of the Hecla mine at Burke. It has a maximum capacity of 900 tons per day and all ore treated is drawn from the company's Hecla mine. Milling ore for 1910 contained 9.7 per cent of lead, 1.2 per cent of zinc, and 4.77 ounces of silver per ton.

Jan 1, 1932

[ ]

Jan 1, 2008

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.

By C. A. Frenzel

Extensive spectroscopic data are needed in making reliable vibrational assignments for use in calculating thermodynamic functions of polyatomic molecules. The fundamental vibrations of organic molecules may be observed at any wavelength from 2.5 to 200 microns (micron = µ = 10-4 centimeters), but most often in the region from 3µ to 50µ. Raman spectra generally cover the range in which fundamental vibrations occur, but equally important infrared spectra usually are not measured at wavelengths longer than 25µ. This limitation results because most infrared spectra are determined for analytical purposes, which seldom require information outside the region 2µ to 25µ. Measurements of infrared spectra in the range 15µ to 35µ recently were begun by the Bureau of Mines to obtain data needed in making vibrational assignments. This report presents the spectra of the following thirteen compounds: Tetrahydrofuran, 1-methylpyrrole, piperidine, 2-methylpyridine, 3-miuthylpyridine, 2-propanethiol, cyclopentanethiol, 2-methyl-2-butanethiol, 3,3-dimethyl-2-thiabutane, cyclohexanethiol, cyclopentyl-l-thiaethane, 2,4-dimethyl-3-thiapentane, and hexamethyldisiloxane.

Jan 1, 1960