Search Documents

By C. K. Rose

A hydraulic scaling rig was placed in operation at the Bureau of Mines oil-shale mine near Rifle, Colo., in 1953. The rig consists of a self-leveling platform mounted on a hydraulic-powered boom. The boom is mounted on the bed of a diesel truck. The equipment provides a movable work platform from which two men can work in safety and comfort while barring loose rock from the backs and walls of the rooms, pillars, and haulageways. INTRODUCTION As a part of its synthetic liquid fuels program the Bureau of Mines has developed a mine in the richer oil-shale beds of the Green River formation near Rifle, Colo. An important part of the work of the Oil-Shale Mining Branch is investigation of techniques for low-cost mining of oil shale on a commercial basis. It is evident that scaling loose rock from the high backs and walls of the mine represents a portion of the direct mining cost. This paper describes the development of a scaling rig for operation in the upper heading of the mine, which is 39 feet high.

Jan 1, 1954

Although the technology involved in removing material from below the earth's surface has a long history, communication systems in underground workings are relatively new to the industry. Communication equipment did not begin appearing in underground mines until the early 1900's. Figure 1-1 shows a miner using a Western Electric standard telephone set for underground mines in 1913. These early phones were essentially the same as those used aboveground, except that they were enclosed in cast-iron boxes as protection against moisture, acid fumes, and gases. In the 1950's, the Chesapeake and Potomac Telephone Co. of West Virginia introduced a telephone set for use in explosive atmospheres that was designed around the philosophy of explosion containment. To contain an explosion within the telephone set required a 39-pound casing, which greatly limited portability. [ ] Both of these telephone sets required "pipe" or conduit, not a very practical item for a 100-squaremile coal mine. A common thread prevalent in the first 40 years of design and development is that the primary effort was placed on the telephone set. In the early 19701s, as work began on the design of modern communication systems for use in underground mine environments, the following requirements were established: 1. Must meet intrinsic safety standards .--This applies not only to coal mines, but to other explosive environments. 2. Must be compatible with the environment.--The system must with- stand dust, moisture, and corrosive conditions. 3. Must be rugged in structure.-- The system must withstand maintenance by 10-inch pliers and 4-pound hammers, as well as impact from a falling piece of roof. 4. Must be size-flexible.--Whatever is built must be sized for the small operator as well as the large companies. 5. Must be a total system in design.--The system must be intrinsically safe, including cable, power supply, and station set. 6. Must work with present telephone system.--The system should be compatible with aboveground communications already in place; it should not be the single cause of change in aboveground communications. 7. Value-added pricing.--The system should be reasonably priced so that savings created by its introduction will more than offset the installation cost.

Jan 1, 1984

By E. E. Remmenga

Often a collection of analytical data, which should reasonably be expected to follow the normal distribution, contains too many extreme values, which the experimenter is inclined to eliminate according to some arbitrary procedure. The stepwise computer procedure described for this purpose is similar to many other truncation procedures; however, because truncation of a basically normal distribution causes a downward bias in the estimated variance, this procedure provides a graphical method to compensate for the bias.

Jan 1, 1971

By Robert F. Chaiken

The U.S. Bureau of Mines conducted an experimental and theoretical study of coupled chemical kinetic and mass transport processes during leaching of pyrite from coal in a counterflow, "trickle-bed" column reactor. Spatial and temporal data on reactant and product concentrations were used as solutions to appropriate continuity equations, which in turn define chemical kinetic reaction rates. Data from four 180-by 30-cm column leaching experiments using coal, coal waste, and air-water and air-FeC13 lixiviants have been analyzed. The rate of leaching was found to be diffusion limited (probably by Fe3+) and not controlled by bacterial action. Rates of pyrite oxidation were found to vary with elapsed time (80 to 225 days) and followed a bell-shaped curve, sometimes with a delay before start of reaction. Maximum rates of reaction ranged from 3 to 10 (mmol/d)/L (column) for coal waste and 0.4 (mmol/d)/L (column) for coal. Reaction was 30 to SO pct complete, probably due to precipitation of product salts (e.g., jarosites), which impede transport of oxidant through the coal. An absorption-desorption model of solids leaching, which considers the role of heterogeneous porosity in solids leaching, was used to describe time-dependent leaching rates.

Jan 1, 2010

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By G. R. Hopkins

[ ]

Jan 1, 1927

By T. J. Ballard

The Ore Knob mine, in Ashe County, N.C., was one of the largest producers of copper in the eastern states during the 1870's. The ore occurs in a fissure vein, which strikes N. 64° E. and dips nearly vertical. The country rock is granite gneiss. Drilling indicated that the vein structure is approximately 200 feet wide and 1,500 feet long. The vein material shows evidence of replacement of the original gneiss by sulfides. Solution cavities in the vein were noted in some places. The ore minerals and pyrrhotite, chalcopyrite, pyrite, and minor quantities of sphalerite. The gangue contains biotite, magnetite, albite, calcite, and many silicate minerals.

Jan 1, 1948

By Fred Leighton

The least squares method of rock noise source location presented is shown to be more accurate and reliable than standard direct solution methods. This method is particularly effective in improving solutions from rock noise locations outside of geophone array boundaries. A least squares solution for a medium .in which the seismic velocity is the same in all directions is also presented. In this special case, one can solve for both the source coordinates and the velocity.

Jan 1, 1972

By H. R. Shell, John L. Miller, M. V. Denny

In the mica research program conducted by the Bureau of Mines at Norris , Tenn . , many micas other than silicon fluorphlogopite have been synthesized . It has been well established since the initiation of the program that synthetic micas are important materials useful for their superior or unique properties as well as substitutes for natural micas . The possibility of controlling the physical properties of synthetic mica by isomorphic substitution of other ions in the fluorphlogopite lattice further emphasizes the importance of these materials . Accurate measurement and reporting of their properties constitute an essential part of the research program . The study of germanium fluorphlogopite is in keeping with the requirements of a comprehensive study on isomorphic substitution , specifically to identify precisely the material -- chemically , structurally , and optically . The X- ray measurements , including indexed powder and single crystal data , with a description of the methods used to obtain these data , are provided . 5 Earlier work on germanium mica by R. A. Hatch et al . (5) gave an estimate of the cell parameters from X - ray powder data , but no attempt was made to index the diffraction pattern or to determine the space group symmetry . Later work by E. A. Schatz and J. C. Withers (9) listed X- ray and optical measurements , but no attempt was made to index the mica or determine its symmetry . Roth (7) found that germanium dioxide having the a - quartz structure , when heated with equimolar percentages of MgO , CaO , Sr0 , or Ba0 at 1,235 ° C , formed ABO3 -type compounds , e.g. MgGe03 isostructural with enstatite (MgSiO3 ) . Geo₂ also has a rutile - type polymorph with Ge ++ ions in octahedral coordination . Germanium was substituted for silicon in the serpentine structure by Roy and Roy (8 ) using hydrothermal techniques . These authors wrote as follows : "The substitution of Ge + for Si + yielded a magnesia - germania serpentine , formed easily in euhedral hexagonal plates which in some instances were visible in the light microscope . Electron micrographs and the sharp X - ray diffraction patterns confirm a plate - like rather than tubular habit . " It has been shown in this investigation that substitution of germanium for silicon in the mica structure is readily accomplished without radically changing the characteristics of the mica . Substitutions in the mica structure take place in three locations : Tetrahedral , octahedral , and interlayer positions . The tetrahedral positions are normally occupied by Sit or by a combination of Sit with Al +3 the most common combination being 2A1 +3 and 6Si +4 · , The octahedral position , which has six - fold coordination in phlogopite , contains a larger cation such as magnesium . In muscovite it contains only 2A1 ions ; therefore , this mica is considered a dioctahedral mica , whereas phlogopite is considered trioctahedral . +3 The interlayer position has twelve - fold coordination with six oxygen ions from each of two adjacent tetrahedral silica layers . This is the cleavage plane of the mica and commonly contains the largest cation in the mica structure (e.g. potassium) .

Jan 1, 1964

By J. D. Marchant

As part of its mission to assure the maximum recovery and use of the Nation's mineral resources, the Bureau of Mines, investigated an improved procedure for producing rare earth-silicon alloys. For example, a charge consisting of 681 grams of mixed rare-earth oxides, 309 grams of ferrosilicon (75 wt-pct Si), and 182 grams of aluminum metal along with a flux consisting of 681 grams of CaO and 45 grams of MgO was reacted at 1,500° C in an induction furnace. Good slag-metal separation was achieved. The alloy product contained, in weight-percent, 53 RE, 28 Si, 11 Fe, and 4 Al with a rare earch recovery of 80 pct. In current industrial practice rare earth recoveries are usually about 60 pct in alloy products that contain approximately 30 wt-pct each of rare earths and silicon. Metallurgical evaluations showed the alloys prepared in this investigation to be as effective in controlling the detrimental effect of sulfur in steel and cast iron as the commercial rare earth-silicon-iron alloys presently used in the steel industry.

Jan 1, 1980

By Paul M. Tyler

The value of mica depends chiefly upon the size of the flat sheets into which it can be split and also upon whether it is clear or stained. Muscovite (white mica) and philogopite (amber mica) are the micas of commerce. Biotite (black mica) and other varieties are virtually unsalable. Vermiculite, an altered mica having the extraordinary property of expanding greatly when heated, preferably should not be classed commercially as mica. Mica is marketed as (1) cut or uncut block, (2) sheet, (3) splittings, and (4) wet or dry ground mica. In the United States, mica that will not yield flat films over about 1-1/2 inches square, or that is ruled, rumpled, or flawed in any way, can be sold only as scrap, its sole use being for making ground mica. Only sizes that will yield rectangles 1-1/2 by 2 inches or larger can be classed as sheet quality; slightly smaller sizes may be classed as punch, and under certain circumstances still smaller sizes, down to about 1 inch square, may be used for splittings, which are mostly a thousandth of an inch thick or even thinner. Splittings, however, are produced in large quantities only in British India, where labor costs very little. Even there the work is done mostly by children, who not only work cheaper but have a delicacy of touch that enables them to do the splitting faster and better. No mechanical process yet devised will permit ordinary splittings to be made economically in the United States.

Jan 1, 1938

By Nicholas Kyriazi, John P. Shubilla

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1992

By Ronald D. Hill, Elmore C. Grim

The cost of reclamation can vary widely, depending on the primary objectives of the restoration activities. statistics in this study originated from State files, publications, and personal communications relating to restoration and pollution control measures for previously mined lands (orphan lands) and active mines. Reclamation of orphan lands is generally considered a public burden and constitutes an economic problem. All work reported here was completed under government contract, by the lowest bidder, with money coming from State and/or Federal funds. Cost would have been substantially lower had the reclamation been concurrent with mining. Several persons connected with some of the projects have observed that costs could probably be reduced by at least one half, if the reclamation had been conducted along with the mining. The expense of clearing and grubbing of volunteer vegetation, disposal of buried trees and brush, loosing of compacted spoil, and re-establishing access to areas could be saved. In addition, a contracting firm doing the work for a government agency would have mobilization costs and receive a profit. Mining companies also are profit conscious and would consider these costs in anticipating their profits (e.g., overhead would be less if reclamation is integrated with mining). The data presented here should serve as a guide for estimating and determining cost ranges, however, it should be recognized that variations exist. Adjustments may be necessary from the standpoint of physical conditions, economic conditions, price changes, and more restrictive requirements of recent surface mining laws. Reclamation conditions, procedures and successes in the eastern United States, particularly in Appalachia, have no bearing on conditions to be expected in the western United States. The situations are wholly different. Reclamation in the West differs from th t in the East, primarily because of aridity especially a during the summer months 1). Because of the many variables and differences between reclamation in eastern and western areas, they will be discussed separately.

Jan 1, 1974

By H. D. Jacobs

The Federal Bureau of Mines, as part of a program to insure future raw material needs for the iron and steel industry, undertook research to beneficiate the oxidized taconites from the western Mesabi range in Minnesota. The data presented were obtained by applying the Bureau-developed selective-flocculation/cationic-flotation process to the second of three oxidized taconite samples. These three samples are representative of an estimated 10 billion tons of ore analyzing 30 to 40 pct iron. The experimental work was performed in a 900-lb/hr pilot plant. Treating the ore sample (36.1 pct Fe) with the Bureau's process produced commercially acceptable concentrates averaging 63.5 pct Fe and 4.3 pct SiO2, with an average iron recovery of 84.6 pct.

Jan 1, 1980

By Henry E. Perlee

Air compressor explosions that are caused by the ignition of combustible vapor mixtures cannot be explained by a single reaction mechanism or sequence of events. Explosions have been caused by the sudden release of large quantities of lubricating oil, by the rapid vaporization of oil that had accumulated slowly in high-pressure piping, and by the production of decomposition products from carbonaceous deposits. Ignitions can be caused by the heat produced in a catalytic reaction, in a compression process, or when a shock wave is propagated through a combustible vapor-air mixture. The frequency of these ignitions can be minimized by establishing proper maintenance and cleaning schedules. Further study is needed to satisfactorily correlate the various factors involved in compressor explosions.

Jan 1, 1963

By C. F. Winquist

The Bureau of Mines is engaged in research to evaluate the effects of cutter bit wear at coal mine faces. This paper addresses one element of conical bit wear, bit rotation. A discussion on mounting configura-tion and bit forces and their effects on rotation is presented. The effects on rotation and bit forces of bit attack angle, cutting depth, and skew are determined for two types of conical bits during linear cutting of sandstone-inclusive rock. The results indicate that a 10° negative skew angle and 35° attack angle produce the maximum rotation of 17.5° for each foot of cutting. Data on bit rotation and bit forces are presented in an appendix.

Jan 1, 1985

By Thys B. Johnson

A three-dimensional dynamic programing method is presented for determining the optimal ultimate open pit limit. The method given is based on the block concept and is an extention of the two-dimensional Lerchs-Grossmann approach. The three-dimensional technique presented herein is fast and simple and may be used for an initial open pit evaluation when only limited data are available or as a more refined model when the entire deposit is well delineated. The method is illustrated by simple numerical examples and is also presented in algorithmic form. A computer program was written in Fortran IV which implements the three-dimensional algorithm and some computational aspects are discussed.

Jan 1, 1971

Predict the spontaneous combustion potential of a coal, using an expert system computer program. Background Approximately 15% of underground coal mint fires in the United States are attributed to spontaneous combustion. These spontaneous combustion fires frequently occur in worked-out or abandoned areas of a coal mine, This makes the control and extinguishment of the fire difficult and often requires large sections of the mine or even the entire mine to be scaled for long periods of time. A prior knowledge of the self-heating potential of the coal can be useful in preventing spontaneous combustion fires through the use of aggressive monitoring and control measures at existing coal mining operations, and in the planning oh new mines. Many factors can affect the spontaneous combustion process in a mine, including the self-heating potential of the coal, ventilation, geologic factors, and mining conditions and practices. Various test methods have been used to evaluate the relative self-healing potential of coals, including crossing point temperature and adiabatic heating methods, and oxygen adsorption techniques. However, these tests arc usually time-consuming and difficult to conduct, limiting their use to laboratories.

Jan 1, 1992

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

Strategies for monitoring methane levels during roof bolting in an extended cut entry were evaluated. Testing was conducted at the Pittsburgh Research Laboratory’s methane test gallery. Operating conditions were varied and methane releases at the face and drill holes were simulated. Methane readings were taken at the face, and at locations outby the face. Results show that, when the major source of methane was at the drill holes, the highest methane readings were at locations on or 6.1 m (20ft) inby the bolting machine. Methods for selecting better outby sampling locations, when the majority of the methane is released at the face, are examined. During roof bolting it is easier to sample at these outby locations rather than at the face. Further testing is needed to determine what relationship exists between methane concentrations at the outby locations and at the source of the methane release.

By F. W. Lee

Operating engineers and mining executives are interested in the science of applied geophysics, but are looking for a simple and understandable exposition of its problems, instead of dissertations which are becoming more and more involved and increasingly difficult to comprehend. It may be well to discuss the goal, the attempted methods of reaching it and the psychological motive, if any, tack of the science. Where does the subject of applied geophysics stand from the viewpoint of (1) the physicist, (2) the mathematician, and (3) the geologist? Fundamentally, the science aims at a differentiation of subterranean geology with the object of finding useful mineral products by the study of gravitational, magnetic, seismic, electric, and other fields which may be associated with the materials naturally or which may be applied to them. The more skillfully these fields are recognized, applied, and analyzed the greater will be the possibility of interpreting results in a way that will be remunerative both economically and scientifically.

Oct 1, 1931