Search Documents

By J. R. Alldredge

This Bureau of Mines report presents a computer code that has been developed for describing and testing the statistical distribution of general continuous data sets. The statistical distributions used include the normal, lognormal, exponential, chi square, gamma, and uniform. Histograms for observed and expected values are plotted for each distribution. An example using geologic data obtained from a study of the geometric properties of natural fractures in oil shale rock illustrates the use of the computer program, GDIST.

Jan 1, 1977

By J. P. Hansen

The Bureau of Mines has investigated the S02 leaching of MgO from high-MgO-bearing Florida phosphate concentrates. The S02 was effective in leaching some of the MgO from three phosphate concentrates; flow rate of the S02 and leach time were major factors in determining the amount of MgO leached. Calcining the samples, then grinding to minus 200 mesh, and elevating the leach temperature gave only small increases in the amount of MgO leached. The research also showed that some of the MgO was so intimately associated with the phosphate mineral that it could not be removed by S02 leaching. This amounted to about 0.6, 0.7, and 1.0 pct MgO in three leached residues. The calculated heads for the three concentrate samples averaged 1.4, 1.1, and 1.5 pct MgO, respectively, before leaching.

Jan 1, 1985

By F. D. Stevenson

A metal diaphragm pressure relay system was constructed to measure vapor pressures of the metal halides, oxyhalides, and other substances at temperatures up to 700° or 800° C. The vapor pressure of arsenic (III) oxide (As2O3) was determined to verify the reliability of the apparatus for such measurements. The data for the liquid AS2 Os (2820 to 4830 C) are represented by the equation, log Pmm = 6.875 - 2,929/T, from which the normal boiling point was calculated to be 461° C. The heat of vaporization calculated from this equation was 13.40 ±0.09 kcal/g mole As4OS and is essentially constant over the interval studied. The melting point of the octahedral arsenic (III) oxide was determined to be 278° C from the inter-section of the solid and liquid vapor pressure curves, A thermal analysis apparatus is also described by which melting and transition temperatures could be checked by a method independent of vapor pressure data. The melting points of the monoclinic and octahedral forms were determined to be 314.4 ±1.4° C and 278 ±5° C, respectively.

Jan 1, 1963

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By NIOSH Publications

In 2004, 14,478 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (48.9%) were sand and gravel mines, followed by stone mines (30.4%), coal mines (13.9%), nonmetal mines (5.1%), and metal mines (1.7%).

Sep 1, 2007

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By A. R. Rule

This report describes preliminary studies by the Bureau of Mines to develop a procedure for extracting the fluorine from low-grade fluorspar ores in which the CaF2 particles are finely locked in the calcite matrix. A combination of flotation beneficiation and pyrohydrolysis is applied to recover and to liberate the fluorine. Flotation of a finely locked high-calcite fluorspar ore containing only 11.7 pct CaF2 recovered over 92 pct of the fluorspar at a grade of 51 to 52 pct CaF2. Pyrohydrolysis of the flotation concentrate liberated nearly 90 pct of the fluorine as aqueous HF. By this procedure over 80 pct of the fluorine contained in the original ore was extracted.

Jan 1, 1974

By E. G. King

Heats of formation of three crystalline oxides of rhenium (Re02, ReO3 and Re207) have been determined by the method of solution calorimetry, using an aqueous perchloric acid--ceric perchlorate solvent. Copper metal and cupric oxide were utilized as auxiliary substances. Heats were determined at 298' K for the reactions Re + 2CuO = Re02 + 2Cu, Re + 3CuO = ReO3 + 3Cu, and 2Re + 7CuO = Re207 + 7Cu. Standard heats of formation were derived using the value of -37.23 ±0,15 kcal/mole as the heat of formation of CuO. The standard molal heats of formation of the rhenium oxides were determined: Re02, -107.3 ±0.8 kcal; ReO3, -140.8 ±0.9 kcal; and Re207, -301.9 ±1.8 kcal.

Jan 1, 1969

By D. L. Sawyer

The Bureau of Mines studied alumina extraction from uncalcined, kao-linitic clay at temperatures from 1000 to 2500 C using 20-or 27-wt-pct-HCI concentrations and with an acid-to-clay ratio of from 0.8 to 1.4 times stoichiometric. Autogenous digestion pressures ranged from atmospheric pressure to about 900 psia. Extraction of 96 pct of the alumina was obtained by HCI leaching at temperatures and leaching times that varied from 1000 C for 120 h to 2000 C for 15 min. Hydrochloric acid stoichiometry of the reaction A1203'2Si02'2H20 + 6HCI + 2AICl3 + 2Si02 + 5H20 was studied at different temperatures and leaching times in a 750-mL tetrafluoroethylene-polymer-lined autoclave. A combination of high temperature and 20 wt pct excess HCI promoted rapid and almost quantitative extraction of alumina (99 pct in some tests). Additional Bureau data obtained with 35-mL tantalum bombs and leach-ing tests with added fluoride are also provided. At high temperatures, the addition of fluoride did not result in a significant improvement over HCI alone and was deleterious to the filtering properties of the digest residue.

Jan 1, 1985

By E. L. Garton

The Bureau of Mines for a number of years bas been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2915. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By A. R. T. Denues

"INTRODUCTION The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining.In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives. Cushioned blasting is designed to save the energy usually lost in excessive shattering and in this way to effect economies and to produce increased proportions of desirable lump coal. That this saving should lead to greater efficiency is indicated by an analogy with the theory and experience of size-redaction by crushing or grinding from which it is known that a large proportion of the energy consumed is expended in producing the smaller sizes (26),3/. Aside from these considerations, increasing the yield of lump coal is important in practice because larger sizes of coal usually sell at higher prices. Some statistics published in England in 1934 (63) illustrate the economic origin of the interest in increasing yields of lump coal; these indicate for three sizes of coal that as the size decreases the value decreases in the approximate series 3:1.5:1, thus:"

May 1, 1940

By Gerrit V. R. Goodman, Jeffrey M. Listak, John A. Organiscak

Data on dust control practices, geology, and occupational exposures were gathered for approximately eighty underground continuous mining units. Despite silica contents in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/rn3 on a majority of occupational dust samples while the remainder had difficulty maintaining this level. These two sample sets were termed group A operations and group B operations, respectively. Analyses of productivities, geologies, and dust control parameters revealed only minor differences between these two groups. Subsequent analyses of face ventilation design showed considerable differences in silica exposure and silica content between group A and group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber', This face ventilation system may benefit operations having difficulty controlling silica dust exposure and silica dust content. Finally, the collected data showed that occupational samples from group B operations possessed generally higher silica exposures and silica content than similar samples from group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

By H. E. Powell

The magnetic susceptibilities of 34 manganese-bearing minerals were determined. The source of each sample and petrographic, spectrographic, and chemical analyses are given. Included are values for ismorphous series showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By C. J. Johnson, C. J. Bise

"The occurrence of Coal Worker's Pneumoconiosis (CWP) ·has been potentially linked with several characteristics of coal such as rank, volatility, percent content of ash and non-coal components, quartz content, and the presence of several trace elements. According to the National Research Council, numerous epidemiological Studies: indicate that the incidence of CWP varies significantly with the composition and/or the concentration of the coal mine dust.Although advances in dust suppression techniques have markedly reduced respirable dust levels in underground coal mines, the National Research Council has concluded that chemical characteristics of respirable dust from different coal seams should be studied. With this objective in mind, research has been conducted in underground coal mines located in the eastern and mid-western United States, and in the laboratory to characterize the elemental composition of mining-generated airborne dust and laboratory-generated dust derived from samples taken from these mines. The goal of the research is to determine if a relationship exists between mining-generated and laboratory-generated dust from the ·same mine. Results of this research will be presented. ,"

Jan 1, 1988

By Carlton E. Brown

[The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted. in South Africa about 19164/ and more recently in England5/,6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting.]

Jan 1, 1938

By P. T. Brooks

Semipilot scale tests were made to demonstrate a newly developed electrorefining process which could be extrapolated to commercial scale in producing high-purity nickel and cobalt from crude nickel metal and high-grade ferronickel. The new process comprises application of solvent extraction techniques to remove and separate cobalt and iron from nickel and the electrodeposition in diaphragm cells of pure nickel and cobalt from chloride-based purified electrolyte. Using water insoluble organic amines, the solvent extraction operations enabled production of commercial-sized nickel and cobalt cathodes of higher purity than that of commercial electrolytic metals. The solvent extraction operation for separation of cobalt from nickel was made simpler than the conventional method. Furthermore, the solvent. extraction operation for iron removal made possible the electrorefining of ferronickel without the prohibitive loss of nickel resulting from the method ordinarily used for iron removal.

Jan 1, 1970

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By Travis Q. Lyday

Ecuador's economy continued to slow in 1982 due, in part, to declining foreign demand for oil, depressed world oil prices, and high international interest rates. Real growth of the gross domestic product (GDP) was estimated to be in the 2% to 3% range, down from the revised 4.3% recorded in 1981 and the 4.5% anticipated officially. In current prices, the GDP in 1982 was estimated at $12.1 billion.2 Inflation abated slightly from that of 1981 to an estimated 13.9% annual rate. The sucre was devalued in May by 32%, the first time in more than a decade, as a result of the pervasive flow of capital abroad. Ecuador's production of petroleum increased an estimated 1.9% in 1982 compared with that of 1981. The consortium of Corporación Estatal Petrolera Ecuatoriana (CEPE), the state oil company holding a 62.5% interest, and Texaco Inc. (37.5%) produced an estimated 98%, or approximately 211,000 barrels per day, of the total from the northern part of El Oriente, the eastern jungle region, where a Texaco-Gulf Oil Corp. partnership discovered oil in 1967. Gulf subsequently sold out to CEPE in 1977 for $117 million, Remaining production was from the Santa Elena Peninsula Fields on the Pacific coast where production has been steadily declining for several years.

Jan 1, 1984

By T. G. Carnahan

The Bureau of Mines conducted laboratory-scale weathering research on a leach residue containing elemental sulfur and mixed metal sulfides. Experiments were performed to determine pH and impurity element concentrations in the effluents as functions of time and to determine the effects on effluent concentrations of mixing the residue with dolomite tailing material. Four 800-day tests were conducted simultaneously. Soluble metal concentrations, especially zinc and copper, were excessive in the effluents from washed and unwashed samples of the residue. Concentrations of up to 20 g/l of Zn and 12 g/l of Cu were obtained. The pH values of the unwashed and washed residue effluents at the completion of the experiments were 2.8 and 1.9, respectively. Sulfuric acid from oxidation of pyrite caused the pH decrease. Mixing unwashed residue with dolomite tailing to maintain a near-neutral pH minimized the heavy metals content in the effluents. The pH in the dolomite tests increased slowly after the first 360 days and attained values of 7.8 and 8.2, respectively, for tailing containing 1 pct leach residue and for tailing devoid of leach residue. Dissolved zinc and copper did not exceed 0.10 g/l of Zn and 0.001 g/l of Cu.

Jan 1, 1982