Search Documents

By E. A. Sondreal

The Bureau of Mines investigated the use of lignite char for producing carbon disulfide; CS2 production rates were as high as when wood charcoal was used as raw material. The maximum space velocity for CS2 produced in the bench-scale study was 9,280 hour-1, reacting sulfur and lignite char at 792° C. The reaction temperature and the temperature at which the char was carbonized were the two most important factors in determining CS2 production rates. Increasing the carbonization temperature in nitrogen from 400° to 900° C advanced the temperature at which carbon disulfide was first produced from 550° to 850° C. The average activation energy for reacting chars with sulfur was 44,000 cal/g mole. The reaction was first order with respect to the partial pressure of sulfur. Increasing the rate of sulfur admission caused a decrease in rate of production at otherwise similar conditions. Rates were not affected by either char size or sodium carbonate catalysis. High space velocities at moderate temperatures using inexpensive lignite chars could offer an economic advantage in the manufacture of carbon disulfide provided that yields were attractive.

Jan 1, 1967

By A. F. Baker

The Bureau of Mines conducted pressure-drop studies in a 4-foot-diameter simulated blast furnace shaft to compare anthracite metallurgical briquets with coke and formcoke. The test materials were used alone, layered, and in mixed burdens of commercial fuel-to-ore ratios. Anthracite briquets had a higher pressure drop per foot than furnace coke, but they had a lower pressure drop per foot than formcoke. This appears to be due to packing and shape, as well as to particle size. The superficial air velocities at which beds of briquets and furnace coke disrupted were about the same. However, if briquets of the shapes and sizes tested are substituted for furnace coke in commercial metallurgical furnaces, higher blowing pressures will be required to deliver comparable amounts of air. Test burdens with more than 5 percent material smaller than 1/4-inch diameter showed significant increases in resistance to airflow.

Jan 1, 1967

By A. U. Christensen

THERMODYNAMIC data for many of the common interoxidic compounds are seriously lacking, and appraisal of possible ceramic or metallurgical applications depends upon dubious estimates. In particular, high-temperature heat-content estimates may be invalid because of unknown phase-transformations. This paper reports experimental heat-content values above 298.15° K. for five interoxidic compounds-the aluminates of lithium and sodium (LiAlO2 and NaAlO2), the ferrites of lithium and sodium (LiFeO2 and NaFeO2), and lithium titanate (Li2TiO3), as obtained by the Bureau of Mines. Sodium aluminate, sodium ferrite, and lithium titanate were found to have previously unknown transformations in the crystalline state. The heats and temperatures of these transformations were evaluated as were also the heats and temperatures of fusion of sodium ferrite and lithium titanate. The heat-content results are assembled in both tabular and algebraic-equation form for use in conducting thermodynamic calculations at temperatures in the range 298°-2,000° K.

Jan 1, 1960

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By T. A. Hendrickson

The Bohemia district, situated about 30 miles southeast of Cottage Grove, Oreg., in the Calapooia Range, has been the major producer of lead and zinc in Oregon. Sporadic production has been Maintained from the district since its early discovery about 1858. In 1942, a selective-flotation mill was built at the Champien mine, which operated for only a short time and was forced to close because of the war and lack of labor. The Champion mill reportedly has been operated as a custom mill for the treatment of ore from the Musick and Helena mines, located in the district sometime in the past. This report summarizes the results of laboratory ore-dressing studies made on ore samples from the Musick and Helena Mines.

Jan 1, 1951

By Max L. Glenn

As part of its goal to minimize requirements for mineral commodities through conservation and substitution, the Bureau of Mines conducted research to develop molybdenum as a potential substitute for superalloys containing the strategic and critical materials, nickel, chromium, and cobalt. Since molybdenum requires protection from oxidation at high temperatures, several complex oxides of the spinel and perovskite structure were investigated to determine which possessed the greatest potential for use as oxidation-barrier coatings. Two spinels (MgCr204 and MgA1204) and five perovskites (BaHfO3, YCrO3, NdCrO3, BaZrO3, and LaCrO3) were selected for testing. Various high-temperature prop¬erties that are important for oxidation-resistant coatings were examined, including diffusion rates of oxygen and molybdenum, recession (vaporization) rates, hardness, erosion resistance, sinterability, reactivity with molybdenum, and ease of application. From the evaluation of high-temperature properties, two spinels (MgCr204 and MgA1204) stand above the other oxides as possible coatings for molybdenum. However, laboratory coatings of MgCr204 at 1,360° C (2,480° F) are equivalent or inferior to currently available MoSi2 coatings; laboratory coatings of MgA1204 may be comparable under limited conditions to currently available MoSi2 coatings at the same temperature.

Jan 1, 1979

By W. W. Adams

"The National Safety Competition of 1930, the seventh annual contest conducted by the United States Bureau of Mines to promote safety in the mines and quarries of the United States, has been concluded, and the five winners of the bronze trophies, The Sentinels of Safety,' which are provided by the Explosives Engineer magazine and awarded annually for the most excellent safety records, have been determined by the committee of award. One trophy was awarded to an anthracite mine in Pennsylvania, one to a bituminous coal mine in the same State, one to an iron-ore mine in Michigan one to a gypsum mine in Ohio, and one to an iron-ore opencut mine in Michigan.These trophies were awarded to the companies for having the smallest loss of time from accidents in proportion to the total number of man-hours worked by all employees at their mine or quarry. Honorable mention was awarded to each mine or quarry that ranked second, third, fourth, or fifth in its own ground and to all plants that were operated without a lost-time accident during the contest year. Eighty-four out of 337 plants that competed for the trophies were operated without an accident that disabled an employee beyond the day on which the accident occurred.Under the contest rules, all mines and quarries were divided into five groups, four of the groups representing different classes of underground mining operations (anthracite, bituminous coal, metallic ore, and nonmetallic mineral), and the fifth group repre-senting the quarrying or opencut mining of minerals whether metallic or nonmetallic. Twenty-seven mines were included in the anthracite group, 68 in the bituminous group, 52 in the metal group, 24 in the nonmetallic-mine group, and 166 in the quarry and opencut-mine group. The total of 337 mines and quarries was 26 more than the number of plants that completed the contest during the previous year.The committee of award which determined the winners of the contest was composed of seven members, all known throughout the mineral industry but not connected with the United States Bureau of Mines. The committee included W. H. Cameron, managing director of the National Safety Council; William Green, president of the American Federation of Labor; James F. Callbreath, Secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of Mining and Metallurgy; C. B. Huntress, executive secretary of the National Coal Association; A. J. Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the bureau of engineering of the National Crushed Stone Association."

Jun 1, 1931

By Thomas V. Falkie, R. Venkataramani

Hand portable truck axle scales were purchased from the Martin¬Decker Company, Santa Ana, California, for weighing the rubber-tired mine shuttle cars. The scales consisted of two hydraulic load-pads, measuring 4" thick, and 21" long by 13" wide at the pad surface and one totallizer-dial indicator unit. The development of a technique to install the scales effectively for shuttle car-weighing followed an evolutionary process. The setup which finally proved to be effective entailed countersinking and level¬ling the load pads in the floor on the shuttle car trackway such that the tops of the pads were three inches below the floor level. A plat¬form consisting of two braced side-by-side 3" x 8" lumber planks was made. The platform was placed across the load pads with six inches of overlap on each side to provide room for imperfect tracking of the shuttle car. Additionally, 3" x 8" lumber planks were imbedded across the runway immediately behind and ahead of the platform. These auxili¬ary planks were firmly braced into the floor by vertical posts or jacks set against the roof; the planks constituted a stable approach platform to enable the shuttle car to roll unimpeded onto the scale platform in either direction of travel. Figure 22 shows this arrangement in detail. The setup of the scales was done during non-production hours prior to the first working shift of the week. This task took seven to twelve hours with two men. During the actual weighing experiment, the following limitations were realized. 1. Delays will be introduced into the cycle of operations because the shuttle cars must be stopped and positioned on the platform. However, these delays can be held to a minimum, time wise, as the

Jan 1, 1972

By A. W. Decora

Gas-liquid chromatography has been applied to separating basic nitrogen compounds, such as pyridines and amines. Close-boiling compounds have been separated by exploiting structural and polarity differences, using selective liquid substrates dispersed on specially prepared solid supports. Development of these special supports was necessary in order to obtain symmetric peaks for basic nitrogen compounds; solution of this problem was important in applying gas-liquid chromatography to the analysis of basic nitrogen compounds found in shale oil. Attempts to analyze shale-oil tar bases by conventional gas-liquid chromatographic techniques, using Chromosorb4/ or Celite 545 as the support for a nonpolar liquid substrate, resulted in asymmetric peaks. These asymmetries were caused by adsorption of sample vapors on the solid support. Symmetric peaks were obtained when strongly polar liquid substrates were used on either Chromosorb or Celite. However, a solid support giving symmetric peaks only with strong polar substrates restricts the choice of substrate, and frequently, desired separations cannot be achieved.

Jan 1, 1961

By B. K. Shibler, J. V. Batty, G. M. Potter, H. D. Snedden

"INTRODUCTION As a part of the investigations of strategic mineral deposits in the United States under the Strategic Minerals Act. Engineers of the Bureau of Mines examined and sampled numerous deposits pf fluoride ores in the Western States. Sample from those deposits that warranted further investigation were submitted to the Ore Dressing Section of the Salt Lake Station for metallurgical testing. This paper gives data summarizing the results obtained from laboratory studios of fluorite ores submitted from 12 deposits in Arizona, California, Idaho, Montana, Nevada and Wyomong. Only four of the Ores were found to be amenable to beneficiation for the production of acid-grade fluorspar concentrates with good recoveries. However, all of the samples were amenable to the production of concentrates meeting chemical specifications for metallurgical-grade spar.For the sake of clarity and convenience in presenting data, this report has been divided into six parts, each pertaining to metallurgical studies of fluorspar ores of a single State."

Nov 1, 1947

By T. A. Sullivan

The use of sulfur combined with either sand or waste copper tailings was investigated by the Bureau of Mines as a substitute for a good graded aggregate in asphalt paving materials. The research was part of a utilization program to develop meaningful uses for a projected oversupply of sulfur. Many sections of the country lack good aggregate for paving but do have available sources of sands and sulfur. The development of paving mixtures of desert sands or tailings with sulfur and asphalt was accomplished in the laboratory and tested by laying small paving test sections. Three types of material were studied for use with the sulfur and asphalt. They were (1) a concrete sand similar in gradation to river or beach sands, (2) desert blow sand, and (3) waste copper tailings. Desert blow sand and waste copper tailings are much finer than concrete sand. Mix designs were established for the three types of materials, sulfur, and asphalt used in the paving materials. The best mix designs were as follows, in weight-percent: 80.5 concrete sand, 13.5 sulfur, and 6 asphalt; and 77 either blow sand or tailings, 17 sulfur, and 6 asphalt. Small-scale testing showed that these mixtures were suitable paving materials but would require specialized equipment for transporting and laying. The chemical modification of sulfur to obtain properties that would allow placement of these materials with normal asphalt paving equipment was studied. Results indicate that reacting sulfur with dicyclopentadiene before adding it to the paving mixture was effective in modifying the sand-sulfur-asphalt paving so it could be placed and rolled with conventional equipment.

Jan 1, 1975

By A. L. Engel

The Stayton Mining District in San Benito County, Calif., near Hollister, includes several square miles with many occurrences of antimony ore. The sample submitted for the test described in this paper came from a vein said to have been traced and sampled for 5,000 feet on the surface, 1,500 feet carrying 2-1/2 to 3 percent antimony and the remainder 1/2 to 2 percent. Thirty thousand tons 'With a content of 3 percent antimony are said to be blocked out. A drift of 200 feet on the vein has shown ore containing 4.2 percent antimony. The present sample assayed 3.8 percent. Previous flotation investigation of this are resulted in a recovery of only 71.6 percent in concentrates containing 56.8 percent Sb. It was desired to develop a method of treatment that would give better results. The antimony in the sample occurred as the mineral stibnite, Sb2S3, antimony sulfide.

Jan 1, 1949

By S. J. Schatzel, J. Cervik, A. A. Campoli

The cross-measure borehole technique is being studied by the Bureau of Mines as an alternative to the use of surface gob boreholes as a means of controlling methane in gobs during longwall mining. Small-diameter holes are drilled from underground locations into strata overlying the mined coalbed. When the roof strata are fractured by the mining opera- tion, a partial vacuum applied to the boreholes draws the methane out of the fractured strata and prevents it from entering the mine ventilation system. Tests in the Upper Kittanning Coalbed showed that 50 pct of the methane produced by the longwall mining operation was captured by the cross-measure boreholes. Borehole inclination and penetration into the gob are two important borehole parameters that affect the performance of the cross-measure borehole system.

Jan 1, 1983

By William Y. Mo

This report presents preliminary results of a study undertaken to investigate quantitative characteristics of the demand for steel mill products and its major end-use components. The major end uses included in the study are the steel mill products used in construction, in automobiles, in producer durables, and in consumer durables. The main objectives of the research underlying this study are as follows: (1) To formulate and estimate the empirical demand relations for steel and the four major end uses in the United States; (2) to measure and calculate the responsiveness of the U.S. per capita steel consumption with respect to the changes of the steel and other nonferrous metals prices; (3) to determine and quantify the relative importance of the underlying demand explanatory factors in contributing to the average year-to-year increases (or decreases) of the U.S. per capita steel consumption; and (4) to adapt and use the estimated demand relations in making projections of the U.S. future demand for steel and the major end-use components. After extensive preliminary investigation, three versions of simple linear demand relations are selected and estimated by means of ordinary least squares (OLS) method. The annual data for the period 1947-65 are used in the estimation. Direct and cross price elasticities of demand are computed for each of major end uses. The relative importance of demand explanatory factors in contributing to the average year-to-year changes of U.S. per capita steel consumption are also calculated. For making projections, a simple autoregressive time trend model is used in estimating the future values of independent variables. Since the estimated demand relations are valid for projections only if the estimated parameters can be assumed to be unchanged in the future, and consequently, the projections derived in the study should be interpreted accordingly.

Jan 1, 1970

By R. E. Brewer

A critical review of the numerous test methods that have been devised for measuring the "plastic" and "swelling" properties of bituminous coking coals and the practical evaluation of the data obtained has long been needed. The author appreciates fully, first, the arduous problem of doing justice to the merits and limitations of the many original test methods and their manifold modifications and, second, the more difficult task of interpreting the test data obtained in their practical applications to the important problems involved in the coking process. It has been the constant aim of the author to point out the broader significance of the test principles employed in the different classes of test methods and the usefulness of the test data obtained in relation to the problem of coking bituminous coals, rather than to stimulate unduly a controversial criticism of the merits and limitations of any particular class of test methods or of individual test methods devised by different workers. The task has been quite difficult because of the almost total lack of accepted test standards and specifications.

Jan 1, 1942

By R. A. Guereca

Preliminary to an experimental study of selected physical properties of helium and related gases) the Bureau of Mines Helium Research Center conducted a data-gathering literature survey. This report combines the results of the 1961-63 literature search into a usable format. The data accumulated on the physical properties are presented in tables and graphs. The data in the tables were chosen for exact representation and comparison of specific values. An attempt was made to select the most reliable and consistent value available for a given property without extensively analyzing each source reference. The methods of evaluation are discussed later. The graphs show trends and anomalies which may be obscure in tabular form. (Reprints of the graphs) with the scale grid enlarged 2 1/2 times) are available upon request through the Research Director) Helium Research Center.) The literature search was conducted using Chemical Abstracts as the primary reference source with additional information drawn from Applied Science and Technology Index) Chemical Reviews) Physics Review) Science Abstracts (Physics») and other abstracting services. Part of the data included in this report have been tabulated previously by others (£-1).5 In a few areas) the sources of information are scarce and obscure (for example) refractive index and dielectric constant). The search was extensive; however) some sources

Jan 1, 1967

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By T. A. Sullivan

The Bureau of Mines investigated modified sulfur concretes as one part of a program for utilizing sulfur in construction materials. The use of modified sulfur was studied as a means of preventing the stressing action in the concretes caused by the allotropic transformation of sulfur on solidification. Unmodified sulfur concretes have been prepared that have compression, flexural, and tensile strengths equivalent or better than Portland concretes. However, most of these concretes have been vulnerable to deterioration by weathering, temperature fluctuations, and freeze-thaw cycling. The sulfur was modified by reaction with dicyclopentadiene or dipentene before use as an aggregate binder. Sulfur concretes and modified sulfur concretes were pre-pared from acidic and basic type aggregates. Physical properties of the optimum mixtures were determined and compared with each other and with Portland cement concretes. The best results were obtained by reacting sulfur with 5 pct dicyclopentadiene to prepare modified sulfur concretes. Field testing of the concretes are in progress. Present results show that modified sulfur concretes are superior to unmodified sulfur concretes and equal or better than Portland concretes in compressive, flexural, and tensile strengths. Long-term aging characteristics of both modified and unmodified sulfur concretes are being determined.

Jan 1, 1976

By Deno M. Pappas

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining, Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a laboratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 2010

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.