Search Documents

By L. A. Haas

The feasibility of removing sulfur dioxide by carbon monoxide reduction in a fixed-bed catalytic reactor was investigated by the Bureau of Mines. The reduction rate of sulfur dioxide with carbon monoxide was significantly dependent upon the iron and alumina content of the mixed catalyst. Maximum catalytic activity was obtained with about 40 percent iron-alumina mixture with a nominal gas mixture of 10 percent carbon monoxide, 5 percent sulfur dioxide, and the balance nitrogen. The synergistic effect of this catalyst mixture was explained by a dual reaction site mechanism, with both iron and alumina augmenting their specific sites at their interparticle contacts. The catalytic activity also increased with decreasing catalyst pellet size. With O.7-mm pellets, the entire pellet appeared to be catalytically active in a 2-gram catalyst bed. The apparent activation energy of the reaction was 18.3 kcal per mole in the temperature range of 350° to 600° C. Carbonyl sulfide (COS) was produced by the interaction of carbon monoxide and sulfur. The amount decreased with decreasing CO concentration. The ratio of COS formed per SO2 removed reached a maximum at about 400° C. The reaction rate appeared to be independent of S02 concentration in the range of 0.2 to 16 percent. The rate, however, increased directly with the CO concentration in the range of 5 to 20 percent. The presence of CO2 (<15 percent) had no appreciable effect on the rate. However, not over 0.5 percent oxygen could be tolerated. This method appears feasible for removing S02 from waste gas if the oxygen is removed prior to the catalytic S02 reduction process.

Jan 1, 1971

By David E. Siskind

The U.S. Bureau of Mines and the State of Indiana cooperated with AMAX Coal Co. and its consultants to determine the effects of coal mine overburden blasting on nearby pipelines. Five pressurized 76-m pipeline sections were installed on the Minnehaha Mine highwall near Sullivan, IN, for testing to failure. Four 17-to 51-cm-diameter welded steel pipes and one 22-cm PVC pipe were monitored for vibration, strain, and pressure for a period of 6 months while production blasting advanced up to the test pipeline field. In contrast to previous studies of small-scale, close-in blasting for construction, these tests involved overburden blasts of up to 950 kg per delay in 31-cm blastholes. Analyses found low pipe responses, strains, and calculated stresses from even large blasts. Ground vibrations of 120 to 250 mm/s produced worst case strains that were about 25 pct of the strains resulting from normal pipeline operations and calculated stresses of only about 10 to 18 pct of the ultimate tensile strength. No pressurization failures or permanent strains occurred even at vibration amplitudes of 600 mm/s.

Jan 1, 2010

By B. W. Madsen

A modified transpiration apparatus was devised by the Bureau of Mines to permit rapid and accurate measure of the vapor transport and vapor diffusion coefficients of antimony sulfide (Sb2S3) and other compounds at temperatures to 1,045 K. The apparatus was equipped with dual condensers and valves to switch the flow of vapor in a fraction of a second from one condenser to the other, thus allowing short-interval sampling under equilibrium conditions. Reliability of the technique was established by measuring the vapor pressure of ZnC12 as a function of temperature and comparing the results with published data. As part of an investigation of the vapor concentrations and species of accessory element sulfides associated with copper and zinc smelting, the apparatus was used to measure the rate of vapor transport and diffusion coefficients of vapor over liquid Sb2S3 as a function of temperature between 870 and 1,045 K. The calculated vapor density was combined with published direct measurements of vapor pressure to calculate the average molecular weight of the gaseous species. Average molecular weight of the vapor in equilibrium with Sb2S3 ranged from 286 to 112 g/mol over the temperature range studied.

Jan 1, 1983

By Earl T. Hayes

THIS BIBLIOGRAPHY has been assembled to aid research by the Bureau of Mines, and others on high-purity tungsten. It appears approximately 50 years after the development of ductile tungsten-one of the first metals to be produced in a high-purity form. Requirements of the missile age are ever more demanding that engines rout hotter and space vehicles fly higher and faster. Thus, it has become necessary to reexamine all conventional materials of construction as well as to investigate new combinations. At this stage of our technology we have alloys capable of operation at 1,800° F. and several possibilities of developing some. that will be satisfactory up to 2,500° F. Strength-weight comparisons, detrimental to tungsten at, lower temperatures, disappear at this point, mid tungsten or its alloys appear to be the only metal capable of operation at truly high temperatures. The aim of this bibliography has been to include only references that concern improving the purity of tungsten-from processing the ore to treating the finished metal. In this sense it is a selected and not a critical bibliography. The period front January 1911 through February 1959 has been covered. Because repent literature has the greatest, value, most of the selected items refer to publications issued within the pest 5 years.

Jan 1, 1960

By Irving Hartmann

At the 9th International Conference of Directors of Safety in Mines Research a paper6/ was presented describing the initial phases of research by the Safety in Mines Research Establishment at Buxton, England, on the remote control of timber fires with high-expansion foam plugs in a rock tunnel. The work received extensive publicity, and great interest was aroused by the implied possibility that the method might be used successfully to control coal-mine fires, which for various reasons cannot be approached and attacked by standard fire fighting measures and frequently require sealing extensive, valuable coal properties and lead to loss of production and coal reserves and occasionally loss of lives. To investigate the practicability of the foam-plug technique under American min¬ing conditions, with room-and-pillar-type extraction and multiple entries, the Bureau of Mines in 1957 began an investigation at its Experimental Coal Mine, Bruceton, Pa, In preparation for this work it was necessary to rehabilitate and reinforce an elliptical tunnel in the mine where studies had been made, many years ago, leading to development of a ventilation system used in the Holland Tunnels between New York and New Jersey, and in many other vehicular tunnels.

Jan 1, 1958

By A. F. Colombo

Laboratory-scale tests were conducted by the Bureau of Mines on an argillaceous Michigan copper ore and mill tailing to determine the feasibility of leaching with acidified ferric sulfate solutions. The ore and tailings, containing 1.24 and 0.24 percent copper, respectively, were from the White Pine Copper Co., Ontonagon County, Mich. The investigation showed that ferric sulfate leaching of the ore and tailings followed a predictable pattern. Thus, with 4 hours of leaching, up to 58 percent of the copper in the ore was extracted, but prolonged leaching (2 to 3 weeks) was required to dissolve more than 90 percent of the copper. Similarly, about 50 percent of the copper in the mill tailings sample was dissolved in a few hours, but 8 days or more were required for extractions of over 90 percent.

Jan 1, 1962

By A. C. Smith

The U.S. Bureau of Mines evaluated the effectiveness of automatic water sprinkler systems on the suppression of incipient and propagating conveyor belt fires under ventilated conditions. Large-scale experiments were performed at airflows ranging from 1.1 to 4.6 m/s. In incipient fire experiments with 100°C, standard-response sprinklers installed above and between the belts, the sprinklers activated later, the peak heat release rates were larger, and more belting was consumed at the higher airflow. In similar experiments with 74 °C, fast-response sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of belting consumed was slightly higher at the lower airflow. In incipient fire experiments with sprinklers located only above the top belt, the heat release rate and amount of belting consumed was larger at the higher airflow. The propagating fire experiments showed that sprinklers located above and between the belts were effective in stopping flame propagation. Peak heat release rates and amount of belting consumed were larger at the higher airflows for both the 74 °C, fast-response and 100 °C, standard-response sprinklers. The sprinklers were equally effective at each airflow.

Jan 1, 2010

By W. A. McKinney

A sample of oxidized copper ore from a large deposit located in Pinal County, Ariz., about 50 miles northeast of Tucson, was treated by the Federal Bureau of Mines in a small-scale continuous pilot plant by a procedure which comprised acid curing complemented by water leaching and countercurrent decantation washing in a series of drag classifiers. A feed was prepared by pugging minus 1/4-in, ore with concentrated sulfuric acid and about 10 pct, of eater, followed by curing in batches for about 24 hr. The cured ore was fed continuously to a leach drum, where it was mixed with advance solution from the countercurrent washing system to dissolve the sulfated copper. The pulp was thickened and washed in four Esperanza-type classifiers, using a flocculating agent to obtain rapid settling and thickening. The leached ore pulps thickened satisfactorily in the drag classifiers when about 0.8 lb. of a polyacrylamide flocculant per ton of dry feed was used. Clear overflow liquors were obtained, and classifier rake products containing about 60 pct. solids were produced, As much as 90 lb./hr. of ore was treated in the plant, with a recovery of 60 pct. of the total copper or 80 pct, of the acid-soluble copper when 2 tons of water per ton of feed was used in washing. The acid consumption was 4.3 lb./lb. of copper recovered. On the basis of the maximum feed rate employed and the effective pulp-settling area of the classifiers, a total of 1 sq. ft. of pool area was required per ton of dry feed per day for the thickening and washing operations. The washing efficiency in the test was 95 pct.

Jan 1, 1960

By J. A. Lamonica

The Bureau of Mines studied a pulsation damping device designed to smooth pulsating flow in personal respirable dust samplers. The effect on the pulsation dampener efficiency of six parameters was investigated, as follows: Volume, diaphragm elasticity, diaphragm area, center orifice area, inlet-outlet orifice area, and geometry (LID ratio). The results indicate that volume pre-dominates in determining snubber efficiency, while the other parameters become important at small volumes. Geometry has no effect on snubber efficiency. Criteria for an efficient pulsation dampener construction were obtained.

Jan 1, 1971

By Eric Zahl, John Dunford, Hamid Maleki

Coal bumps are defined as sudden failures of rock and coal near entries that are of such a magnitude that they expel large amounts of material into a mine opening. Coal bumps are influenced by geologic conditions, the geometric design of coal mine excavations, and the sequence and rate of extraction. Researchers from private industry and the National Institute for Occupational Safety and Health have studied mechanisms of violent failure and have identified individual factors that contribute to coal bumps. In an attempt to develop tools for assessing coal bump potential, the authors initiated a comprehensive study using information from 25 case studies undertaken in U.S. mines. Multiple linear regression and numerical modeling analyses were used to identify the most significant variables contributing to coal bumps (excluding bumps related to fault-slip). Twenty-five geological, geometrical, and geomechanical variables were considered initially. The most important of these variables were then identified as (1) energy as calculated using the mechanical properties of the strata, depth of overburden, and joint density, (2) mining method, (3) pillar factor of safety, and (4) stress gradient and yield characteristics.

By A. J. Forney

A high-Btu gas was made at the Bruceton, Pa., laboratories of the Bureau of Mines to demonstrate the feasibility of using the gas as a nonpolluting fuel for automobiles. The pilot plants at Bruceton were revised to combine the processes of coal gasification, gas purification, and catalytic methanation in one overall system. Tests in the Bureau&apos;s test automobiles at Bartlesville, Okla., showed the Synthane gas was less polluting than natural gas.

Jan 1, 1972

By Norma Golumbic

The primary purpose of the Bergius (hydrogenation of coal) and Fischer-Tropsch (hydrogenation of carbon monoxide) processes is the production of synthetic liquid fuels. This objective is of importance in insuring an adequate supply of motor fuels and lubricating oils in the United States. In the urgency of the basic research and process development work on synthetic liquid fuels, the possibilities for the production of synthetic chemicals inherent in these processes have hitherto received little attention in this country. However, the by-products, as well as the primary products, from the Bergius and Fischer-Tropsch processes are rich source materials for organic chemicals. The overhead oil from liquid-phase hydrogenation of coal, for example, contains benzene, toluene, xylene, cyclohexane, methylcyclohexane, aromatic solvents, about 20 percent tar acids (largely phenol, cresols, and xylenols), and 3 percent nitrogen bases. Wax, alcohols, and acids are by--products of the Fischer-Tropsch synthesis. In addition, techniques have been developed which make possible the production of aliphatic hydrocarbons, alcohols, acids, aldehydes, and other oxygenated organic compounds. These chemicals are more valuable on a unit basis than gasoline. Because of continued rapid expansion of the plastic, resin, lacquer, and solvent industries, larger amounts of many of these chemicals will be needed in the near future.

Jan 1, 1949

By A. E. Wells

A critical study of the wet Thiogen process for extracting sulphur from the smoke of smelters is one of several investigations related to the general smelter-smoke problem that are being conducted under the direction of the Bureau of Mines. Part of the work done in the pyrometallurgical section of the cooperative metallurgical exhibit of the Bureau of Mines at the Panama-Pacific International Exposition during 1915 related to this investigation, and at the expiration of the exposition, the work was continued in the labora- tories of the Bureau of Mines in the Hearst Memorial Mining Building of the University of California, Berkeley, Cal., where a mining experiment station of the bureau has been established under the cooperative agreement with the University of California. Early in the spring of 1915, when plans were being made to co- operate with several metallurgical interests, the Thiogen Co. proposed to the Bureau of Mines that, along with the studies of various pro- posed methods for eliminating sulphur dioxide from smelter smoke, there should be included a study of the wet Thiogen process. In the study as outlined it was proposed to determine whether it would be technically and commercially feasible to use the, process for the recovery of elemental sulphur from the sulphur dioxide in waste smelter gases. Although there had been no large-scale work with the process, either in the laboratory or at a smelter, representatives of the metallur- gical and mining industry had shown considerable interest in the proposed method, and the desire had been expressed that a better knowledge of the possibilities of the process should be obtained. Thus, cooperation with the Thiogen Co. seemed justified by the in- terests of the metallurgical industry, and by the conservation promised by the recovery of a product of market value from what is otherwise a waste, and in some instances a serious nuisance. In accepting the responsibility for directing this investigation, the officials of the Bureau of Mines were necessarily free to conduct the work in the manner they considered necessary to determine the facts. It was also understood that any information obtained was to be made available to all who might be interested and might be printed in a Bureau of Mines report. To cover the cost of laboratory equipment and supplies, and the payment of salaries of assistants, other than Bureau of Mines employees, the Thiogen Co. in May, 1915, deposited with the cooperative metallurgical exhibit fund a sum considered sufficient to warrant starting the laboratory investi- gation. The origin and organization of this fund has been described by Clevenger and the author." In outlining the program for this investigation it was hoped that ultimately a small complete plant would be erected and the investi- gation center around the operation of the plant. However, pre- liminary to the erection of the plant, a laboratory study of the proc- ess was considered necessary, as the technical features of the process could be determined, it was believed, as satisfactorily on a smaller scale as on the scale first proposed. However, it was realized at the time that it would not be possible to determine so satisfactorily or definitely the commercial possibilities of the process on the scale of work adopted as in the larger operating plant. With this fact in mind it was planned that, if the study of the technical features on a laboratory scale gave sufficient promise of the process being commer- cially feasible, an operating unit should, if possible, be constructed later, and that more definite information concerning the commercial prospects should be determined. The investigations were started in June, 1915. In June and July work was confined entirely to small-scale laboratory tests, in which a careful study of the chemical reactions involved was made. In August, tests on a larger scale were started, and these were con- tinued until December, small-scale tests being made at the same time. On December 1, 1915, all work on the Thiogen process was discon- tinued temporarily, as the close of the exposition necessitated moving the laboratories. Work on the Thiogen process was started again in January, 1916, in the laboratories of the new mining experiment sta- tion at Berkeley, Cal., and was continued during the spring of 1916 until a point was reached where it was felt that the essential parts of the process had been carefully covered, and that some definite state- ments concerning the technical features and possibilities of the process, as given in this report, were warranted.

Jan 1, 1917

By J. G. Linn, H. H. Schrenk, W. P. Yant, R. R. Sayers, John Chornyak, F. A. Patty, S. J. Pearce

"This report is the first of a series dealing with the results of a comprehensive investigation of methanol poisoning, conducted jointly by the Federal Bureau of Mines, Carbide & Carbon Chemicals Corporation, du Pont Ammonia Corporation, and the Commercial solvents Corporation.The study dealt mainly with physiological effects produced by inhalation of methanol vapor, and concentration studied ranged from approximately 500 to 15,000 p.p.m., and periods of exposure from 4 hours daily to continuous. The range of concentrations and periods of exposure were such as to produce acute effects, with and without fatalities, by a singel exposure and chronic poisoning, with and without fatalities, as well as little or no response after repeated daily exposures. In addition to the inhalation experiments, skin absorption was studied, and field surveys were made to ascertain the hazards associated with the manufacture and, use of methanol."

Feb 1, 1942

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

By Timothy A. Clancy

In support of research on forming ceramics from mining and processing wastes, the Bureau of Mines tested various commercial refractories to evaluate their resistance to melts of these wastes. Sixteen refractories of various types were exposed in slag erosion tests to two siliceous waste melts with Si02/CaO ratios of 4.0 and 2.2, The extent and nature of slag attack were then determined for each refractory. The nature of slag attack was investigated through scanning electron micrographs and microprobe elemental distributions. The refractories that performed best in resisting attack by the melts were high-alumina types, and of the refractories tested, the most resistant was a 90-pct-Al203, 10-pct-Cr203 refractory.

Jan 1, 1983

By W. A. Selvig

"The purpose of the investigation described herein was to determine how closely different laboratories can check one another in making determinations of fusibility of coal ash with the De Graaf electric coal-ash fusion furnace: how well duplicate determinations by the same laboratory will check, and how the results with the De Graaf furnace compare with those of the standard gas-furnace method of the American Society for Testing Materials.4Thanks are due the following laboratories who cooperated in this study by making fusibility tests with the Do Graaf electric coal-ash fusion apparatus: J. J. Brennan, testing engineer, Northern States Power Co.; R. E. Gilmore, superintendent, Fuel Research Laboratories, Canadian Department of Mines A. T. Leavitt, president, and W. Mueller, chief chemist, Hamilton By-product Coke Ovens. Ltd.; Edgar Stansfield, chief chemical engineer, Scientific and Industrial Research Council of Alberta. Canada; and H. S. Vassar, laboratory engineer, Public Service Electric and Gas Co.The ash-fusibility determinations by the standard gas-furnace method were made in the Coal Analysis Laboratory of the Bureau of Mines at Pittsburgh under the direction of H. M. Cooper, associate chemist. The investigation was made at the suggestion of A. C. Fieldner, chief engineer, Experiment Stations Division of the Bureau of Mines.Routine determinations of the fusibility of coal ash are made in the laboratories of the United States Bureau of Mines by the gas-furnace method. This method was standardized after considerable experimentation5 on the nature of the fusion of coal ash and the various factors which affect its determination. The method was subsequently adopted by the American Society for Testing Materials as one of its standard tests."

Jun 1, 1930

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By Richard J. Bielicki

The possibility of replacing the brattice cloth closest to the coal mine working face with an air curtain mounted on top of a continuous-mining machine or with a diffuser fan was explored by the Bureau of Mines. Preliminary tests conducted at a full-scale model working face with the brattice end set at 18 feet showed that the air curtain improved face ventilation only slightly and was not nearly as effective as placing the brattice at 10 feet. A 2,000-ft3/min diffuser was more effective than the air curtain. It is concluded that the air curtain probably could not function as a line brattice extension, although the diffuser fan may have some potential.

Jan 1, 1975

By A. C. Fieldner

This report, the third of a series of annual reports of research and technologic work on coal by the Technologic Branch to be released in this form, covers the fiscal year July 1, 1937, to June 30, 1938. Ever-increasing demands for information on the chemical and physical properties of coals, their proper classification rind adaptability for various uses, their economic evaluation in the complex relationships between the costs of production, distribution, and selling, and their beneficiation and amenability to conversion to more valuable and. new products of commerce have necessitated an appropriate and flexible program. To most these requirements, initiation of new projects and new physical facilities has been made.

Jan 1, 1939