Search Documents

By L. A. Haas

The U.S. Department of the Interior, Bureau of Mines, is conducting laboratory-scale research to determine the leaching conditions required with sulfuric acid for extracting base metal from a matte with a copper-to-nicke1 ratio of 6 to 1. The matte (61.2 pct Cu, 9.7 pct Ni, 3.3 pct Fe, 21 pct S, and about 5 oz of precious metals per ton) was prepared from Duluth Complex (Minnesota) ore by smelting a bulk sulfide flotation concentrate. The matte was pre leached at atmospheric pressure to selectively extract 20 pct of the nickel, and the undissolved solids were referred to as the matte residue. Autoclave leaching of the matte residue extracted over 95 pct of the nickel, copper, and iron. The remaining leach residue in the autoclave contained over 100 oz of precious metals per ton. The leaching conditions required were matte grind of greater than 98 pct minus 325 mesh, pulp concentration of 50 g/1, total pressure of 100 psig with oxygen at 150° C or 400 psig with air at 180° C, 50 g/1 H2S04, 700 rpm agitator speed, and 6 hours of leaching time. The leaching time was decreased to 2 hours by increasing the agitator speed to 1,300 rpm. Sulfuric acid concentration greater than 50 g/1 did not appreciably enhance the base metal extraction, but with less acid, residues with higher iron concentrations were obtained. Supersaturation of the liquor was prevented at 150° C by using a 1ixiviant that contained 30 g/l Ni and 20 g/1 Cu.

Jan 1, 1979

By J. R. Thoenen, J. D. Warne

"INTRODUCTION Red-iron-ore deposits in northeast Alabama have been exploited at vari¬ous times for nearly 6o years. About 3-1/2 million tons of ore have been produced in the Gadsden district; but mining activity has been dormant since 1926, and furnaces within this section of the State now suffer a shortage of red ore.To alleviate these shortages, work by-the Bureau of Mines was recommended after preliminary investigations. 4/5/ Diamond drilling, to determine the lateral and vertical extent of ores of known deposits in Greasy Cove and on Shinbone Ridge, was done from August 1946 to May 1947, as Project 9-106, Alabama Red Iron Ore. Three holes were drilled in each area.ASKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of domestic mineral resources to the end that they- make the greatest possible contributions to the national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as possible after its conclusion. The Mining Division, Lowell B. Moon, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests."

Jun 1, 1948

By R. A. Bloomfield

This report summarizes Bureau of Mines contract research on the disposal of retorted oil shale. A data base has been developed describing the physical-chemical properties, geotechnical engineering properties, and natural cementation characteristics of spent shale. Results of field compaction tests and seepage pond tests are presented, along with results of a partially saturated finite element seepage model used to predict infiltration and seepage rates. Preliminary engineering analyses are presented for underground disposal systems, which include material transport methods, and for a surface disposal system, which includes stability analyses.

Jan 1, 1981

By G. W. Birge, D. E. Wolfson, J. G. Walters

An investigation was conducted to determine the relationship between ASTM and Micum tumbler data and to develop equations that would enable the conversion of data from one test method for comparison with those determined by the other , and thereby facilitate the international exchange of data . Relative strengths of 18 commercially produced cokes were determined by ASTM and Micum tumblers and ASTM shatter test . Two of the samples were coke produced for foundry use , and two were produced in beehive ovens . The remaining 14 samples were produced for blast furnace consumption and had ASTM tumbler stabilities of 36 to 58. Statistical procedures were used to relate the three test methods and also to evaluate the effect of charge weights , top sizes of coke , and types of screens specified by the two standard tumbler procedures , square - hole wire mesh for the ASTM tumbler and punched round - hole for the Micum . A significant result was that the data obtained with like screens have a higher degree of correlation with a smaller standard deviation than data from the screens specified for each tumbler .

Jan 1, 1964

By H. H. Schrenk

[A colorimetric method5/ for the determination of benzene in amounts as low as 0.001 mg has been developed recently at the U.S. Bureau of Mines Pittsburgh Experiment Station by the authors, with the assistance of chemical personnel fro a the Allegheny County (Pa.) Relief Works Division. The method is based on the direct nitration of either liquid - or gas - phase benzene, followed by neutralization, extraction with butanone, and final treatment with sodium hydroxide which produces a violet color. The color is matched with color standards of known values. Although the method is adaptable to many conditions the primary objective was a procedure that would be suitable for hygienic investigations. The development worth included a study of possible interference by chemicals that be present in those situations in which the method. would be employed. In this study it was found that a specimen of hexane prepared by the Gulf Research Laboratory, Pittsburgh, by fractionation of West Virginia natural gas gave positive result for benzene, whereas a specimen of pentane prepared in the same manner showed only a trace, and specimens of n -heptane and octane (2,2,4 trimethylpentane) supplied by Eastman Kodak Co. save a negative result. According to information obtained from the Eastman Kodak Co. the latter two compounds were highly purified, the n-heptene being prepared from line and the octane synthesized in the laboratory. On nitration of a larger amount of tae natural hexane a visible quantity, of needlelike crystals which resembled those of m-dinitrobenzene was obtained. The hexane from this nitration was recovered by distillation and again nitrated, but no crystals or colorimetric indication of benzene was obtained. This imitated that the specimen of natural hexane contained a substance which at least had the chemical behavior of benzene.]

Jan 1, 1935

By H. A. Doerner

From thermodynamic calculations3 Maier predicted that zinc oxide Land methane would react at specified temperatures substantially according to equation (1). (1) ZnO + CH; = Zn (gas) + CO + 2H2 Other reactions that may take place are: (2) CH4 = C + 2H2. (3) ZnO + CO = Zn (gas) + CO2 (4) ZnO + H 2 = Zn (gas) + H2O . Maier predicted that 870°C. would be the critical temperature above which reaction (1) would take precedence over reaction (2) and that reaction (1), at equilibrium, would be substantially complete at or above 927°C.

Jan 1, 1931

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By A. L. Engel

High extractions of lead, gold, and silver resulted from treatment of an oxidized, arsenical refractory ore by chloride volatilization. The ore was roasted in an oxidizing atmosphere at 1,000° C. for 1 hour. The chloridizing reagent was 300 pounds of CaC12?2H20 per ton of ore. Ninety-nine percent of the lead, 98 percent of the gold, and 96 percent of the silver, and only 6 percent of the arsenic, were volatilized. These results indicated that a satisfactory method could be developed for treating this type of ore. Recovery and separation of the volatilized values and developing metallurgical and operating data for this process require further investigation on a more extensive scale. Tests by gravity concentration, flotation, and cyanide leaching did not give satisfactory results.

Jan 1, 1958

By A. B. Cecala

A new prototype bag nozzle system has been designed under a Bureau of Mines contract to reduce dust generated during the bagging operation on fluidized air baggers. A field analysis of the new system has shown that the bag operator's dust exposure was reduced 83 pet. The amount of blowback was reduced 89 pet, which corresponds to a significant product savings. The new prototype system has been operating for a substantial period of time with no major problems.

Jan 1, 1984

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. FLOW CHARTS

Jan 1, 1974

By C. K. Eilerts

Knowledge of the phase relations of the fluids that exist in the porous spaces of rocks constituting natural petroleum reservoirs and of the behavior of these fluids under various field conditions of operation is essential to the conservation of petroleum and natural gas and to their efficient recovery. The problem of determining whether these fluids are in the liquid or gaseous state and of recognizing the transitions that may take place as the material in the reservoir is subjected to different conditions of pressure and temperature confronts many producers today, especially in certain fields. The subject has grown rapidly in importance since the discovery of and production from deeper reservoirs that have correspondingly higher pressures and temperatures as compared with shallower

Jan 1, 1938

By J. A. Cavallaro

The heats of formation of anhydrous barium carbonate (witherite), strontium carbonate (strontianite), and lead carbonate (cerussite) were determined by solution calorimetry. The solution mediums were hydrochloric acid for barium and strontium carbonates and perchloric acid for lead carbonate. The heats of formation at 298.15° K are as follows: BaCO3 -297.5 ± 0.8 kcal/mole; SrCO3 -294.6 ± 0.5 kcal/mole; and PbCO3 -168.0 ± 0.3 kcal/mole.

Jan 1, 1966

By T. M. Kohler, G. L. Finfinger, D. M. Hyman, A. T. Iannacchione

The Bureau of Mines measured methane emission rates from an advancing salt face ranging from 15 to 56 ft3/ton (0.5 to 1.8 m3/t). Small room size, use of a continuous miner, and a well-defined ventilation system made possible air velocity and methane concentration measurements, These measurements, representing data from 18 production days, were con- ducted in an area of abnormally low grade salt, Methane emissions occurred primarily during the advance of the salt face by continuous miner.

Jan 1, 1982

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

By Oliver Bowles

"On January 15, 1920, a man was killed by falling rock in a limestone quarry in Utah. The quarry was visited by a representative of the Industrial Commission of Utah, and the cause of the accident was carefully determined. The facts concerning this accident, and the Bureau's recommendations are given in some detail in the hope that quarrymen may take steps to avoid dangerous conditions, and thus reduce the liability to accident.The quarry rock face is about 180 feet high, and the ledge is covered with an overburden of 10 to 20 feet of a mixture of soil and boulder. The rock face is not vertical, but slants at an angle of about 45° to 50°, while the stripping face stands at an angle of 70° to 80°, and is flush with the rock face. The conditions are shown in the accompanying figure.The man who was killed was employed in breaking rock at the foot of the quarry wall. The sun had been shining on the stripping face, and probably thawed the ground, thus permitting a boulder weighing about 20 pounds to roll down the slanting face, striking, and almost instantly killing the workman who was working with his back toward the quarry wall."

Feb 1, 1920

By L. A. Haas

The Bureau of Mines conducted bench-scale leaching tests with recycled spent copper electrolytes and copper-nickel mattes produced from the Minnesota Duluth Complex concentrates. This report describes the first stage of an overall two-stage leach operation. The objective of this research was to determine the matte-leach technology required to convert spent copper electrolyte into an enriched nickel liquor suitable for a nickel refinery and there-fore essentially free of copper, iron, and sulfuric acid. The experimental variables investigated were matte composition, particle size, spent electrolyte content, pulp concentration, oxygenation, temperature, and time. The time required to produce an enriched purified nickel liquor decreased with increasing pulp concentration, temperature, and oxygenation, but increased with increasing particle size and electrolyte copper and acid content. Nickel-rich (about 50 g/l) liquors at a pH of about 4 and containing less than 1 g/l of copper and iron were produced at 70° C by leaching minus 325-mesh low-iron (less than 5 pct) matte for 8 hours with spent electrolyte containing 22.4 g/l Cu, 28.9 g/l Ni, less than 0.1 g/l Fe, and 50 g/l H2S04 at a pulp concentration of 1 kg of matte per liter of spent electrolyteo Varying the nickel content of the spent electrolyte from 11 to 101 g/l appeared to have no appreciable influence on the matte leaching characteristics.

Jan 1, 1981

By R. L. Rough

The Bureau of Mines analyzed rotary-coring-operations data to compare mud and air as coring mediums, and to compare core recoveries, penetration rates, and cost data for the respective mediums as part of an investigation of the susceptibility to secondary-recovery techniques of petroleum reservoirs in Ohio, Pennsylvania, and West Virginia. This report describes the rotary-diamond coring equipment and operations employed while coring 20 wells--10 cored using mud, and 10 cored using air. Data relevant to the draw works, rotary-table power, drill pipe, drill collars, core barrel, core head, mud pumps, or air compressors are tabulated. Average bit weight and rotary speed, core recovery, and penetration rates are listed for each formation cored. In general, core recoveries were better from the mud-cored wells, whereas penetration rates were faster for the air-cored wells. Coring costs were about the same for single-formation wells cored with either mud or air; however, costs increased considerably when multiple-formation wells were cored with air.

Jan 1, 1969

By Henry P. Wheeler

H ELIUM (chemical symbol: He) is a member of a family of normally gaseous elements, which, because of their zero valence and corresponding lack of chemical activity, are called the "noble" or "inert" gases. It is a monatomic element with an atomic number of 2, and it exists naturally in two stable isotopic forms-He3, with an atomic mass of 3.0170, and He4, with an atomic mass of 4.0039. With the exception of a trace (10-6 percent) of He3, all of the naturally occurring helium is He4. Two unstable isotopes-He5, with atomic mass 5.0137, and He6, with atomic mass 6.0208-are listed by various scientists, but the existence of He5 is questioned by some of them. He6 is radioactive, with a half-life of 0.8 second. Helium was discovered in 1868 in the gaseous atmosphere surrounding the sun. Although several scientists studied the solar chromosphere that year, it is generally agreed that J. Norman Lockyer of England should be credited with the discovery of helium, which he named, deriving the word from "helios," the Greek name for the sun. It was not found on earth until March 1895, when William Ramsay of London produced a small amount from a sample of cleveite, a uranium-bearing mineral. In 1905, H. P. Cady and D. F. McFarland of Kansas found helium in natural gas produced from a well near Dexter, Kans., and for the first time a large source of helium became available.

Jan 1, 1952

By John C. Edwards, Fred N. Kissell

Experimental work by the Bureau of Mines indicates that when a coalbed is degassed by boreholes, the flow of methane may actually increase with time. This phenomenon appears to be the result of a relative-permeability effect; that is, the coalbed permeability to the gas increases sharply with decreasing water saturation. This report reviews the background of experimental evidence indicating a relative-permeability effect, and presents the results of a computer simulation of two-phase flow in coal.

Jan 1, 1975