Search Documents

By Mackenzie Burnett

The Brattice Window Method was used to measure the leakage rates of a total of 42 ventilation stoppings in 8 hardrock mines. Various types of stopping construction were evaluated. The following types are listed in order of decreasing effectiveness: 1) Cinder block, 2) Timber and mortar, 3) Timber and polyurethane foam, and 4) Timber and brattice material. There are slight differences in the effectiveness of the first three types, while the timber and brattice type is substantially inferior to the others. The repeatability of the Brattice Window Method was found to vary with physical conditions in the mine such as stopping location with respect to intersections, regularity of drift cross section, and the presence of hardware such as air and water pipes, timber sets and wire mesh. The Brattice Window Method is viewed primarily as a tool for estimating and comparing stopping leakages for the purpose of determining where repair efforts should be concentrated. A laboratory test program resulted in the derivation of several "rules of thumb" for employing the Brattice Window Method, which will aid in securing accurate and repeatable data.

Jan 1, 1979

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By Richard H. Spencer

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off, However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected.

Jan 1, 1975

By W. H. Rinkenbach, C. A. Taylor

"Among the recently patented detonating compounds that have been suggested as substitutes for the commonly used fulminate of mercury is the normal lead salt of trinitroresorcin, or styphnic acid. As no data concerning its use or practi¬cability were available, a study of its properties was made in the explosives laboratory at the Bureau of Mines experiment station at Pittsburgh, Pa. This paper embodies the results obtained.Normal lead trinitroresorcinate was first prepared and patented*** by Herz; it probably found some use during the World War, but no record of its performance is available,Preparation of Lead Trinitrpresorcinate.In his patent specifications, Herz states that the normal salt may be obtained in a quantitative way by precipitating a multiple of the equivalent weight of the lead salt of a strong inorganic acid - such as lead nitrate - in the presence of a weak organic acid - such as acetic acid - by heating with a Teak solution of the alkali-metal salts or alkaline-earth salts of trinitroresorcin. Herz gives the following example: 245 grams of dry trinitroresorcinand 290 grams of crystalline sodium carbonate are dissolved in in 18.8 liters of boiling water, to which 77 c.c. of glacial acetic acid is added. The toiling solution is mixed with a boiling solution of 650 grams of lead nitrate in 1.4 liters of water, stirring rapidly; and the mixture is boiled for two minutes, after which it is cooled quickly with constant stirring. The precipitated crystals are then filtered off, washed several times with cold water, and dried."

Oct 1, 1923

By T. A. Sullivan

Research undertaken by the Bureau of Mines in 1938 has resulted in the development of titanium from a laboratory curiosity to a commercial metal. Along with processes for producing the metal, it was necessary for the Bureau to develop methods for analyzing the metal, raw materials, and intermediate products. Some of the methods developed have been published.3 4 5/ General Services Administration (GSA) was responsible for purchasing titanium metal under Defense Production Act contracts with commercial producers. GSA designated the Federal Bureau of Mines to analyze this metal and establish its compliance with Government specifications. A substantial quantity of tin was found in some of the samples analyzed, and in July 1957 tin was added to the list of impurity elements to be determined. The specifications limited the amount of tin in titanium sponge to a maximum of 0.10 percent. A program was immediately initiated to investigate methods and techniques for determining tin in the range of 0 to 1.0 percent. A method accurate at the 0.10 percent level was necessary, as this level was the critical range for acceptance or rejection of the metal.

Jan 1, 1960

By W. H. Ode, W. A. Selvig

Investigations have shown interesting relationships between primary-tar and light-oil yields and chemical analyses of coals. These studies have been based largely upon results published by the Bureau of Mines in connection with its survey of the gas-, coke-, and byproduct-making properties of American coals. This paper gives the results of a similar correlation in which the range in rank and type has been extended to include nearly all classes of coal, the object being to determine relationships that are significant in predicting tar and light-oil yields from chemical analyses of coals. The yields of primary tar and light oil are important in two fields of coal utilization, namely, combustion and carbonization. It is generally recognized that the principal cause of smoke produced upon burning coal is incomplete combustion of tar and light-oil vapor released during burning. The greater the tar and light-oil yields of a coal, the greater is its potential smoke-producing property. During the present war, development of new sources of fuel oil has been emphasized, especially where the supply of petroleum products is limited. One possible source of a substitute fuel is the tar and light oil that can be obtained by low-temperature carbonization of coal. In both England and Germany large quantities of low-temperature tar and oil are being processed as a source of liquid fuels. It is obvious that primary-tar and light-oil yields are of paramount importance in the selection of coals for such use.

Mar 1, 1944

By A. W. Henderson

Methods for converting WOCl4 to WCle were investigated in small-scale, laboratory apparatus to devise a method for preparing pure WCls suitable for conversion to tungsten metal. Chlorine, COCI2, and CCI4, alone and in combination with various forms of carbon, were tested as chlorinating agents at various temperatures. More than 95 percent conversion of WOCl4 to WCls was achieved with all reagents at 8000 C in the presence of activated carbon. Only CCl4 maintained its effectiveness in the absence of carbon at 800° C. The effectiveness of carbon was found to be related directly to its surface area.

Jan 1, 1968

By S. Gallagher, C. A. Hamrick, A. G. Mayton, R Sonier, R. L. Unger

Introduction Industrial safety professionals recognize that adequate illumination is essential to a safe and productive work environment. The need for effective, lighting in underground coal mines is even greater.1 Designing appropriate lighting systems for these mines is no easy [ ] task because of the unique environment and work procedures encountered in underground coal-mining operations. Miners must depend totally on artificial lighting systems to see. Moreover, the working face is a low-reflectivity and low-contrast environment and is continually advancing or retreating.2 Laboratory mock-ups have been a major part of the process lighting equipment manufacturers must under- go to design an underground machine-mounted lighting system. The mock-ups often have taken considerable time. Furthermore, modifications to a lighting system (using different luminaires with an existing configuration or changing a luminaire's location, orientation, etc.) could require more time with additional mock-ups and laboratory measurements. Understanding the need to improve this situation, the US Bureau of Mines has developed an alternate method for facilitating lighting system mock-ups. A PC-Program (CAP),* with the latest software technology enables users to design, alter, and evaluate under- ground machine-mounted illumination systems. Lux levels and distance are measured as the luminaire is moved incrementally through angular traverses about horizontal and vertical axes. The measurements and angles subsequently are entered into the model. From this input data, three-dimensional isolux or isofootcandle profiles are constructed for luminaires that can be placed at various locations and orientations on a mining machine. As an example, Figure 1 shows a computer display of 21.5 Ix or 2.00 fc profiles for luminaires mounted on a simulated mine-shuttle car. Using this information, the model allows the user to determine the lux level at different locations in space about the shuttle car. How the model calculates illumination During initial development of the CAP model, the isolux profile of the luminaire was determined using the inverse square law (ISL) .3 The method of gathering data comprised recording a single measurement of distance at 21.5 ± 1.21x (2.00 ±11 fc) for angular traverses following 0.09 rad (5 degree) increments. This data was then used to find the illumination in space for any other distance at a given azimuth and elevation using the ISL. Limitations, however, exist with this method.4 The main one is that the ISL assumes a luminaire is a single point source of light, so long as the distance is greater than five times the 1al;gest dimension of the luminous area of the luminaire.5 Also, by using a single measurement to calculate the illumination for a given luminaire in the CAP model a large error could result from an inaccurate measurement.

By A. J. Kraemer

[A great deal of interest has been manifested in the question of sulphur in fuels for automobile engines. Many different opinions have been expressed with respect to the effect of sulphur in gasoline on engine wear and engine performance. A wide difference of opinion exists as to the permissible limit of sulphur content for satisfactory operation.]

Jan 1, 1927

By A. Gene Collins

The Bureau of Mines conducted a research study of the geochemistry of the Smackover Formation to determine what geochemical relationships are useful in exploration for and production of oil and gas. Samples of oil, gas, brine, and rock were collected and analyzed. The oilfied brines were analyzed by methods recommended by the American Petroleum Institute and by tentative methods of the American Society for Testing and Materials. The crude oils were analyzed by Bureau of Mines methods; the gas, by Bureau of Mines methods; and the rocks, by wet-chemical, atomic absorption, and neutron activation methods. The results were correlated and interpreted, and several geochemical relationships useful in exploration and production were found. These include the type and class of brine, organic constituents in the brine, redox potential, in situ temperature and pressure of brine, degree of sulfate and carbonate saturation of brine, and halide concentrations in the brine.

Jan 1, 1974

By W. F. Watts

The U.S. Bureau of Mines has conducted research on methods to reduce and to measure diesel particulate matter (DPM) aerosols in underground coal mines. One objective of this report is to present findings from an investigation of the DPM reductions obtained by an engine-mounted integrated control system consisting of a dry system (DS) and a diesel particulate filter (DPF). Another objective is to present results from the usc of a size selective personal sampler to measure DPM concentrations in an underground coal mine. Bureau laboratory tests of the integrated dry system and diesel particulate filter (DS-DPF) have shown that DPM emissions can be reduced up to 97 pet with little change in gaseous emission concentrations. The DS-DPF is undergoing certification tests conducted by the Mine Safety and Health Administration (MSHA). Subsequent to passing all safety requirements, it will be tested in an underground coal mine. A baseline survey of DPM concentrations and aerosol size distributions in a cooperating mine was completed in August 1988. A prototype DPM personal sampler was tested during this survey. Based on results from this test, an improved unit has been developed. This unit is scheduled for extensive field testing by MSHA in 1989.

Jan 1, 1989

By Albert E. Long

Diamond-bit performance and cost data accumulated in core-drilling sandstones reveal significant trends of economic interest. Large-size, AA-Grade drill bort suffered less diamond loss per foot drilled than any other size or grade of diamonds assessed. Detailed analyses of the factors that affect diamond-bit performances -diamond size, diamond quality, bit size, bit type, percentage of core recovered, and physical characteristics of bit matrices -are assessed in the tables, graphs, and discussion. INTRODUCTION Since 1945 the Bureau of Mines has been compiling detailed performance records on diamond bits used in core drilling throughout the United States and Alaska. Analytical reports covering bit performance in various rocks are issued as in-formation on a significant number of bits used in anyone type of rock is accumulated. The first three such reports analyzed bit performance in gneiss,2/ schist,3/ and lime-stone and dolomite.4/ This report evaluates diamond-bit performance in sandstone. Data obtained from 627 bits, which drilled 42,665 feet on 45 different projects, are presented. The geographical distribution of the projects is shown in figure 1.

Jan 1, 1958

By John P. McDonnell

Coal mine bounces and bursts are major problems facing U.S. mine operators. Bounces and bursts have the potential to inflict severe injury on mining personnel, damage equipment, and cause mine closures. High- stress conditions, at or near the working face, are the common denominator in the burst problem, If mine operators can locate high-stress and potentially burst-prone zones, they can then use stress-relief methods to control the burst condition. One method of locating the high-stress zone is the probe-hole-drilling or drilling-yield method. Probe-hole drilling is used frequently in Europe, the U.S.S.R., and Japan as a means for locating potential burst zones. Consequently, the Bureau of Nines performed tests in the laboratory and in a deep, burst-prone western mine to analyze probe-hole drilling. The in-mine method, very simply, involves drilling a hole into the coal seam and measuring the volume of cuttings obtained. A certain volume of cuttings can be expected from a certain diameter and length drill hole. A significant increase in the volume of cuttings means the zone around that particular hole is highly stressed. In-mine use of the drilling yield method has shown it to be a useful tool for locating highly stressed and potential burst zones. Results from laboratory testing confirm that high stress applied tri-axially to a cube specimen will cause a significant increase in the volume of cuttings from a small-diameter drill hole in the specimen.

Jan 1, 1988

By M. S. Seehra, V. S. Babu

"INTRODUCTION The accurate determination of the free silica index in coal mine dusts is an important requirement because severe health hazards are believed to be associated with the inhalation of respirable-sized silica particles.1-6 Free silica refers to the three polymorphs of silica (Si02)viz., quartz, cristobalite, and tridymite-although quartz is usually the dominant form in most mine dusts.6 The free silica index is the concentration in micrograms of free silica in air per m3 of air sampled corrected to standard conditions of 25°C and 760 mm/Hg, the present MSHA (Mine Safety and Health Administration) limit on time-averaged basis being 100 µ.g/m 3 for coal mines. A recent review7 has concluded that quartz, cristobalite, and tridymite particles impart nearly equal long-term hemolytic damage when compared on a per unit surface area basis.At present, two experimental methods-viz., transmission infrared spectroscopy (TIRS) and x-ray diffraction (XRD)-are commonly used for the determination of silica concentrations in mine dusts. In TIRS, which has been adopted by MSHA and is commonly called the P7 method, the silica absorption band near 800 cm - 1 is used for quantification. However the mineral kaolinite, which is commonly present in mine dusts, also has absorption band, albeit weaker, at 800 cm- 1• To correct for this interference, one uses the stronger 915-cm -1 band of kaolinite to determine the concentration of kaolinite, and the kaolinite contribution to the absorbance at 800 cm-1 is then determined from a calibration curve, leading to the determination of silica by subtraction. In the XRD technique, usually an internal standard such as CaF 2 is used to determine the concentration of silica from line intensity measurements. XRD has the added advantage that concentrations of quartz, cristobalite, and tridymite can be determined.8•9 In an exhaustive study on the precision of the techniques ofTIRS and XRD for monitoring worker exposure,9 the conclusion has been reached that both methods measure silica within 253 of the ""true"" value 953 of the time in a single laboratory."

Nov 1, 1995

By Robert L. Lagace, Alfred G. Emslie

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

To develop an in-mine water treatment system in which bacterial sulfate reduction and limestone dissolution continuously remove metals and acidity from contaminated drainage. Approach A section of mine tunnel was converted into a water treatment bioreactor by constructing cinder block dams and fang the area between them with a porous substrate mixture of limestone gravel and compost. Readily fermentable materials such as dairy whey, spent brewing yeast, or sugar were periodically added to the reactor. Mine drainage was impounded behind one of the dams and continuously percolates through the reactor substrate at a controlled rate. How It Works The reactor substrate soon becomes anaerobic after it is saturated with mine water. Under anaerobic conditions, sulfate-reducing bacteria consume the organic materials that are added to the reactor and generate hydrogen sulfide (HIS) and alkalinity. The H2S reacts with dissolved iron and heavy metals to form metal sulfide precipitates. The alkalinity raises the pH of the water and induces aluminum to hydrolyze and precipitate as aluminum hydroxide [Al(OH)3]. Additional alkalinity is generated by the continuous dissolution of the substrate limestone. Metal sulfide precipitates and Al(OH)3 are retained within the reactor, and the treated water is discharged. The underground location of the system allows year round operation.

Jan 1, 1994

By Ben A. Kornhauser

Benin's industrial sector experienced severe economic and financial problems in 1986, including disappointing performances of the Onigbolo cement plant and the Semé Oilfield, plus a shortage of technically trained personnel and experienced management. Oil production remained about 1,000 barrels per day. Import and export trade between Benin and the United States remained minimal. Because much of Benin's outstanding external debt was in U.S. dollars, the stronger dollar greatly increased the debt burden. The 1985 budget of $304 million' was composed of an investment budget of $194 million and a current budget of $110 million. Of the investment budget, 84% was expected to be externally financed. About $45 million was given to three priority projects: the joint Benin-Togo Nangbeto hydroelectric project scheduled for completion in 1986; drilling of new exploratory wells of the Semé petroleum project, and the Dassa-Parakou highway. The budget deficit was projected to exceed $43 million despite a decrease in projected revenue owing to an anticipated decline of 25% in import tax revenue, normally the largest source of Government revenue.

Jan 1, 1987

By S. H. Katz

Artisans and laborers in mineral industries where the air is dusty with particles of reel: are subject to a peculiar pulmonary disease known as miners' phthisis or stone cutters' consumption. In granite cutters the disease is specifically designated as granite pneumoconiosis. Very fine particles of the harder rocks are especially injurious when inhaled into the lungs. It is estimated particles about one micron (1/23000 part of an inch in diameter) are most injurious, because larger particles are more readily removed by the cilia and,wet surfaces of the respiratory passages before reaching the lungs, while smaller particles either do not readily lodge or are more easily eliminated. Silica, of which quartz and flint are composed, and which forms a large part of granite, is one of the hardest of the common rock-forming materials. It is also very insoluble when silica lodges in the lungs elimination is difficult. Rock constituents of granite other than silica are probably injurious but in a lesser degree, and this is also probably true of limestone and the softer rocks. Ultimately a worker who daily inhales much granite dust has considerable deposited in his lungs. If he continues at his trade the lung tissue becomes harder and less elastic, he finds himself short winded, and in extreme cases death may come either directly or indirectly as a result of lung failure.

Feb 1, 1921

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976