Search Documents

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By Robert F. Holub

The Bureau of Mines has evaluated four working-level radiation-measurement methods and optimized them from the inherent and statistical error standpoint. Optimization with respect to various sampling and measurement times yielded no marked improvement over the existing methods. However, when appropriate approximations are made and evaluated, these two-measurement methods can be reduced to simple formulas, eliminating a need to use nomograms. These modified methods also have improved inherent error characteristics. A new method--a combination of two existing methods--with improved inherent and statistical errors has been suggested. All the pertinent equations are given, together with the computer program, so that any two-measurement method can be readily evaluated.

Jan 1, 1980

By A. J. Kraemer

[The Bureau of Minas for a number of years has been studying the properties of crude petroleum from producing fields in the United States and Western Hemisphere and has published a series of reports on these fields, including oil fields of Texas.5]

Jan 1, 1927

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By Lloyd A. Morley, Alan M. Christman

Introduction A wealth of information exists which deals with electrical grounding, both from a general viewpoint and from a specifically mine-oriented approach. Many parameters must be investigated in order to thoroughly cover all of the variables which govern the performance of electrical grounding systems. The emphasis of this work on open-pit practices re- presents a new development in the field of grounding research, and an exhaustive review of the relevant historical documentation is especially desirable. Grounding System Purposes What purposes are served by a grounding system? The answer is four-fold and may be summarized as follows. First, it must limit potential gradients between conducting materials in a given area (56). When a phase conductor comes into contact with a machine frame, current flows through the equipment, which tends to become elevated above ground by an amount equal to the voltage on the conductor. If a man were to touch the machine while he was simultaneously connected to ground in some manner, his body would also tend to become elevated in potential, possibly to a lethal extent. Thus, the grounding system should provide a low- resistance path for the fault current to return to the source. The maxi- mum potential to which a man could be exposed when touching a machine frame is equal to the voltage drop along the ground conductors inside the power cable, as shown in Figure 1 (54). The ground conductors, therefore, (page # 96 is missing from the original document)

Jan 1, 1976

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By S. P. Kinney

During 1925, at Holt, Ala., the United States Bureau of Mines made a study of the composition of the gases at four elevations in the shaft of a furnace producing foundry iron. A report3 of the work was published in 1927. Some of the results of this investigation are shown in Figure 1. As indicated, the gas at the center of the shaft is low in CO2 content, while the gas in the vicinity of the wall is higher in CO2. The composition of the gases at the top and at the center of the stock column was not far different from the composition of the gas at the top of the bosh. The investigation indicated clearly that lean gas was channeling through the center of the column. More recently the study was enlarged in scope to include investigation of a furnace operating on Lake Superior ores in the Chicago district. A series of planes between the stock line and tuyères was surveyed. Means and apparatus were developed for obtaining, between the inwall and the center of the furnace, the gas composition, gas velocity, and temperature on each plane. A complete report4 of the investigation has recently been published.

Jan 1, 1929

By F. J. Bailey

"In the fall of 1919, the U.S. Bureau of Mines began an inquiry as to the possibility of utilizing airplanes in conjunction with its rescue work, for quickly transporting engineers and oxygen rescue-apparatus to mine disasters.It was realised that this proposed use of airplanes has serious limitations, and if it were feasible, that the Bureau would have to rely on the cooperation of the established aviation fields of the U. S. Air Service for furnishing airplane service. Therefore Van. H. Manning, Director of the Bureau of Mines, under date of October 28, 1919, wrote the Director of Air Service outlining the rescue and first aid organization of the Bureau, the location of headquarters of district engineers, the distribution of safety cars and stations, and other essential details, and asking whether the Air Service could cooperate with the Bureau in the event of serious mine disasters. Major-General Charles T. Menoher, Director of Air Service, responded that the Air Service would be glad to cooperate insofar as possible, and designated those Air Service stations nearest the district engineers' headquarters, which might be best able to assist.The Bureau of Mines has ten mine rescue cars and eight mine safety stations distributed throughout the mining regions of the United States. The cars are each equipped with sets of oxygen mine-rescue breathing-apparatus and first-aid supplies. The car personnel consists of a mining engineer, surgeon, foreman, first-aid miner, clerk and cook. A foreman miner is in charge of each station and at five of the eight stations are mine safety trucks. The work of the cars and stations is two-fold; (1) Assisting in rescue and recovery work at mine disasters, and (2) training miners in mine rescue and first-aid methods, and in investigations looking to prevention of mine accidents. The country is divided into nine safety districts, with nine district engineers in charge."

Apr 1, 1920

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971

Objective To identify techniques to reduce the probability of gob gas explosions. Background In the last 6 years, seven explosions of methane and/or coal dust occurred within worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many mine seals and caused much damage external to the sealed area. Three of these gob gas explosions occurred in one mine in Alabama over a 3-year period. Fortunately, the explosion forces and the toxic gases that vented from the sealed gob area did not cause fatalities or injuries, but they destroyed several large seals. If miners had been inspecting or working near these areas, the potential for serious injury and/or death would have been high. The United Mine Workers of America and the Mine Safety and Health Administration (MSHA) requested that the National Institute for Occupational Safety and Health (NIOSH) help identify the mechanisms for lightning penetration into the gob and recommend ways to reduce the probability of occurrence of future explosions from such lightning penetrations into sealed areas of underground coal mines. Because three of the explosions occurred in a single mine, special attention was focused on these particular explosions. The first occurred in April 1994 in a sealed area, which enclosed about 1.35square miles of abandoned workings (gob). This explosion destroyed 3 of the 38 seals that surrounded the gob. These seals were less than 2,000 ft away from three 4.5-in-diam steel-cased test wells that extended from the surface into the mine entry. At the time of the explosion, the National Lightning Detection Network (NLDN)verified 12 lightning strikes within 10 miles of the mine, including several above the gob. After the 1994 explosion, the damaged seals were rebuilt using an acceptable seal design capable of with standing a 20-psi explosion, as required by 30 CFR 75.335. On January 26,1996, a second gob explosion destroyed five more cementitious pumpable seals less than 2,000 ft away from those destroyed in 1994and even closer to the steel-cased wells. The NLDN verified72 lightning strikes in the area of this second gob explosion. Compressive strength analyses of fragments from the destroyed seals showed that strengths ranged from 11 to 138 psi, with an average of83 psi. This is over 100 psi below the minimum 200-psi compressive strength requirement for cementitious pumpable seals. These seals were again replaced. On July 9, 1997, the third and most violent explosion occurred in the same vicinity of the last two explosions. Three more cementitious pumpable seals were destroyed, including one newer seal that exceeded the minimum 200-psi compressive strength requirement. The NLDN verified 695 lightning strikes above the mine during the time in which the explosion occurred. MSHA's

May 1, 2001

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig. 1). The average fuel requirement per barrel of crude oil refined has remained virtually stationary for the past 3 years. Thus in 1937 the average was 562,000 B.t.u., in is it rose to 567,000 B.t.u., and in 1939 it declined to 557,000 B.t.u. she largest gains in fuel economy cane a decade or so ago on the widespread introduction of heat exchanges and pipe stills. In recent years many successful innovations in heat saving have been adopted, but the combined effect of those is completely masked by the degree to which the capacity is utilized. Some heat requirements are relatively inelastic, so the average consumption per barrel of crude oil refined tends s to increase when the operating ratio (crude runs divided by capacity) declines and vice versa. In 1939 crude runs to stills increased 6 percent (from 1,165,015,000 barrels in 1938 to 1,237,840,000 in 1939) compared with a decline of about 2 percent in 1938. The operating ratio in 1939 was 82 percent compared it's 78 percent in 1938.]

Jan 1, 1941

By Edmund S. Leaver, Jesse A. Woolf

"The Baboquivari mining district is about 60 miles southwest of Tucson, Ariz., the present railroad shipping point. The values are silver and gold. The silver is largely associated with the black oxides of manganese. The ore is highly oxidized, and careful panning shows only a very small amount of pyrite. Our sample analyzed as follows:A flotation mill has been installed in the district, but it does not concentrate the precious metals satisfactorily. Our best laboratory flotation results were obtained by grinding to pass 65-mesh and floating with Xanthate or standard flotation oils plus sodium sulphide and polysulphide. This sulphidizing method gave a concentration of 32 per cent of the silver and 80 per cent of the gold, which about equals plant practice.We do not know of an instance where the oxidized forms of manganese have been concentrated satisfactorily by flotation.Plain cyanide on the original ore extracts practically all of the gold but only one-third of the silver. A preliminary deoxidizing roast, using producer gas or powdered coal, gives a calcine from which cyanide dissolves about 90 per cent of the gold and 75 per cent of the silver. This method of treatment, known as the Clevenger-Caron process, is described in Bureau of Mines Bulletin 226.Preliminary treatment with sulphur dioxide by burning pyrite or sulphur and passing this gas into the pulp until all of the contained manganese is dissolved or changed in form best prepares the ore for cyanidation. The acid consumption will vary with the percentage of manganese and other soluble constituents. Neither gold or silver is dissolved by this acid treatment. The washed residue gives maximum cyanide dissolution of the gold and silver with minimum loss of cyanide,"

May 1, 1928

By G. St John Perrott

"The United States Bureau of Mines is cooperating with the State of Utah and the City of Salt Lake in an investigation of methods of abating the smoke nuisance in Salt Lake City. In the course of this work samples of the atmosphere have been collected and analyzed in an attempt to determine the part played by sulphur dioxide or smelter gases in polluting the air at Salt Lake City.A fairly wide-spread opinion exists in Salt Lake City that the smelters contribute appreciably to the smoke nuisance. The gases discharged from the smelter stacks are believed (1) to float over the city in a heavy blanket which prevents the smoke from rising, and (2) to unite with the water vapor in the air to form corrosive fogs injurious to health and property.The first of these theories seems untenable. If the gas did not mix with air it would sink, owing to its heavier specific gravity, and form a blanket an the earth. Actually, the gas diffuses rapidly in air and any part reaching Salt Take must he thoroughly diluted. Perhaps sulphur dioxide in sufficient concentration might aid in fog formation. The more obvious nuisance, however, would be the injury to health and vegetation.The Garfield smelter is 16 miles west of the city, The Murray smelter 8 miles south, and the Midvale smelter 12 miles south. Under normal operating conditions, a relatively small amount of solid matter is discharged from these stacks. The toxic gaseous constituent of the discharge is sulphur dioxide, it is being discharged from the smelters the year round. If they are a factor in the city's smoke problem, the concentration of this gas in the air of the city should be appreciable and should increase toward the smelters, the con centration being highest with a south or a west wind."

May 1, 1920

By J. E. Geier

This Bureau of Mines report reviews hypotheses for the mechanism by which water jets reduce the specific energy of cutting for drag bits. Several of these hypotheses are shown to be inconsistent with published evidence and new observations. The notion of a limiting cutting speed, above which water jets would be incapable of rendering assistance, is shown to be improbable. The hypothesis that seems most plausible is that specific energy reductions are mainly due to the erosion of crushed materials from in front of the bit. This hypothesis leads to a prediction that, for a given rock type and jet-bit configuration at a constant depth of cut, the reduction in bit forces should be a function of dM/dx, the jet energy spent per unit length of cut. This dependence upon dW/dx is shown to be consistent with other workers? results.

Jan 1, 1987

By A. J. Farstad, R. G. Olsen

The Coal Mine Health and Safety Act of 1969, passed by Congress in the wake of the disaster at Farmington, West Virginia, led to an extensive study by the National Academy of Engineering of the problems involved in coal mine safety. One of the results of this report and subsequent research conducted by the U. S. Bureau of Mines has been the investigation of electromagnetic techniques for the location of trapped miners after a mine emergency. The Westinghouse Georesearch Laboratory has been involved in both the 2 theoretical and field studies relating to this problem. A compact personal beacon transmitter has been developed which can be attached to and powered by a miner's lamp battery. A compatible lightweight loop antenna package has also been developed which can be easily carried on a miner's belt. This antenna can be quickly deployed on the mine tunnel floor. For the purpose of calculating its electromagnetic fields on the earth's surface, the loop can be considered to be a magnetic dipole buried in the earth. (The earth is assumed to be homogeneous and to have a conductivity of s mhos/m.) The surface of the earth is assumed to be uniformily sloping and the transmitter dipole oriented as in Figure 1. The fields on the earth's surface can be computed by using a superposition of the fields of a 4 vertical magnetic dipole3 and of a horizontal magnetic dipole in proportions which depend on the slope of the terrain. In the case of level terrain a null in the horizontal magnetic 5 field occurs on the surface directly above the dipole. This null is designated as the apparent source location and is the criterion by which the source is located. The criterion was tested at two hardrock mines and two coal mines in the fall of 1972. The apparent source locations were compared to actual locations determined by conventional surveying techniques. It was found that due to nonlevel terrain the apparent and actual source locations differed by up to 13 meters. This discrepancy can be resolved by an examination of the fields of a source beneath uniformly sloping terrain. Figure 2 shows the experimental and theoretical results for a

Jan 1, 1973

By B. B. Letson

The heats of formation of lithium chloride and lithium oxalate were determined with the aid of a Bureau-developed, glass Dewar-type solution calorimeter which uses thermistors as its temperature sensing element. Values obtained at 298.15° K were -98.38 ± 0.54 kcal/mole for lithium chloride and -329.02 ± 0.79 kcal/mole for lithium oxalate, using graphite as the standard state for carbon.

Jan 1, 1965

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988