Search Documents

By L. H. Harrison

In coal mines equipped with electrically driven mechanical mining equipment, the problem of protection for electrical circuits and machinery important, because the hazards of fires and explosions resulting from electrical failures is greater than in most other industries. There is need for better methods and improved protective devices for this service. Studies and tests designed to determine possible value of the short-circuiting contactor as an electrical device for coal mine service were investigated. Preliminary made to determine the operating characteristics of the device, after which tests were made under actual service in three coal mines. Ordinarily, electrical protection in coal mines is divided into three classes, as follows: 1. Overload protection that is intended to protect against damage from overheating and excessive mechanical strain due to overloading. 2. Short-circuit protection that provides a means of de-energizing the equipment instantly when an accidental short circuit occurs in the equipment or on the power system. Short cm protection tends to damage from fires and, explosions resulting in the dissipation of large amounts of electrical energy in a short circuit. 3. Ground fault protection that, in its various forms, is intended, to maintain the frames of electrical equipment at or near the same potential surfaces in contact with the earth for the purpose of safe-guarding human life.

Jan 1, 1951

By I. N. Beall

The present survey indicates 'that the average volatility of motor gasoline now being marketed throughout the country falls well within the limits of Federal Specifications. As would be expected, there is a slight decrease in volatility as compared with the gasoline marketed last wine:., but on the average the gasoline sold today is about the same as that sold last summer. During the past five years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States. To obtain a sample of each gasoline sold is obviously impracticable, but the cities in which samples have been collected have been so chosen as to be representative of the more important marketing territories. It is believed, therefore, that the samples obtained are indicative of the quality of gasoline marketed throughout the country.

Jan 1, 1925

By Henry Kreisinger, WALTER T. RAY

The investigation of the transmission of heat into steam boilers is one of several researches now being carried on by the Bureau of Mines that have for their object the testing of methods by which the mineral fuels in this country may be used more efficiently. A better understanding of the laws governing heat transmission into boilers will result in the design of more efficient boilers, and more efficient boilers will reduce waste in the use of fuel. The results of the investigations described in this report indicate that the conductivity of the heating plates of steam boilers is so high that the present steaming capacities can be tripled or quadrupled by forcing over the heating surfaces three or four times the weight of gases now passed over them. With well-designed mechanical-draft apparatus this greater weight of gases can be forced through the boilers at a small operating cost. It is possible to increase the capacity of many of the present boilers in this way without reducing their efficiency much; in fact by a proper arrangement of the heating surfaces the efficiency can be made higher than the present rating. The efficiency of any boiler can be increased by arranging its heating surfaces in series with respect to the path of hot gases. New boilers of high efficiency can be constructed by making the cross section of the gas passages small in comparison with the length. In Bryan Donkin's book, entitled "The Practical Physics of the Modern Steam Boiler," it is stated that James Watt obtained nearly as good an evaporation per pound of coal and per square foot of heating surface as is obtained now. The remark is probably true. At any rate, about the only decided superiority of the modern steam boilers over older types is in mechanical construction, and for this superiority credit should be given to the designers of machine tools quite as much as to the boiler engineer. The main reason for tardi- ness in boiler improvement probably lies in the reluctance of educated engineers to do the dirty and disagreeable work involved in boiler tests.

Jan 1, 1912

By J. C. Kerkering

The Bureau of Mines used mathematical reliability theory to define, for use in the mining industry, the concepts of risk, safety, reliability, hazard, and mean time between accidents. In this report, the definitions are explained theoretically and illustrated by application to actual underground mine accident data extending over a 9-1/2-year period. The theoretical development proceeds along two parallel analytical paths. For each line of reasoning, the data are presumed to be independent. If they are not, the analysis stops, although there are interesting implications when dependency is demonstrated. The first method uses the elapsed times between accidents as the basic data. These elapsed times are fitted to a negative exponential distribution function using least squares and yielding the function parameter, P1 The P1 is used to form the Poisson distribution function for the data, which is then used to define the safety-related concepts. The second method uses the maximum likelihood estimator to formulate a Poisson distribution function for the data. The function is tested for adequacy by a goodness-of-fit test; if the fit is acceptable, the Poison function is used to define the concepts. Both methods were applied to the data base, yielding nearly identical results.

Jan 1, 1987

By Christopher Van Dyke, Edward L. Petsonk, Knox Van Dyke, Vincent Castranova, Ji-Hee Kang, William Pailes

"INTRODUCTIONPlatelet-activating factor (P AF) has been shown to mediate a broad range of biologic activities (1). Chemical analysis has shown that PAF is a glycerophospholipid with a choline polar head group, an ester-linked acyl chain at the second carbon of the glycerol backbone, and an ether linkage at the first carbon. The alkyl group attached to the first carbon can exist in a variety of chain lengths, with the C16 and C18 forms predominant in humans. The structure of P AF has been identified as 1-0-alkyl-2-acetyl-sn-glycerol-3-phosphorylcholine (2,3).PAF can be released from a variety of cell types, such as basophils, neutrophils, and alveolar macrophages ( 4-6). Stimuli for the release of P AF include calcium ionophore, phorbol esters, chemotactic agents, and zymosan. In addition, endotoxin has been shown to be a potent stimulant of P AF release from alveolar macrophages (7).P AF has been shown to have a number of pulmonary effects. It has been associated with asthma since it can cause contraction of pulmonary tissue (8) and leukotriene secretion from leukocytes (9) and induce airway constriction when inhaled by humans (10). In addition, PAF is a potent chemoattractant and can cause migration ofneutrophils into the airspaces of the lungs (11,12). Endotoxin is a lipopolysaccharide-protein complex derived from the cell walls of gram-negative bacteria. I.PS is the lipopolysaccharide portion of endotoxin. LPS contains four covalently joined subunits: lipid A, 3-deoxyoctonate, a core polysaccharide moiety, and an 0-specific antigenic polysaccharide side chain. Rough LPS contains no 0-antigen side chain. The liP.id A portion of LPS has been associated with most of the biolQgic effects of endotoxin (13). This lipid A subunit consists of a D-glucosamine disaccharide backbone substituted with four fatty acid side chains. Endotoxin is found in a wide variety of occupational settings associated with organic dusts derived from plants or animals, such as cotton, cereal grains, silage, rice, and poultry (14-18). In addition, airborne endotoxin has been found in sewage treatment plants, composting plants, offices with contaminated humidifiers, and showers or saunas (19-22)."

Jan 1, 1990

By F. W. Brown

In 1942 the Explosives Division investigated electrostatic hazards associated with the manufacture, storage, and use of explosives. A report was issued in 19454/ presenting the data on the spark sensitivities of explosives. In 1948, the apparatus was redesigned and rebuilt to make the routine testing of explosives safer and more convenient. The rebuilt apparatus is described in this re-issue of the former report. Included are details of construction and a list of parts. PRINCIPLES OF METHOD In normal procedures without special precautions, it is possible for static charges to be accumulated on individuals or on ungrounded equipment or structures.5/ Static charges may be produced in many ways, but they are most commonly produced by rubbing or successive contact and separation of unlike surfaces, at least one of which is usually an insulator.

Jan 1, 1953

By N. S. Dalal, X. Shi

"This study reports a new property of the important NAD(P)H-dependent flavoenzymes, glutathione reductase, lipoyl dehydrogenase and ferredoxin- NADP oxidoreductase, that can catalyze a one electron reduction of metal ions such as chromium(VI) and vanadium(V). During the enzymatic reduction process, molecular oxygen is reduced to H2O 2 , which reacts with the reduced metal complexes to generate hydroxyl radicals. Since the hydroxyl radicals have been suggested to play an important role in Cr(VI) toxicity, this study provides a basis for a recent observation that Cr(VI) mutagenesis is strongly oxygen dependent. These results also point to an enzymatic pathway for the metabolism of some metal ions and concomitant generation of hydroxyl radicals. l. INTRODUCTIONThe purpose of this communication is to report that some important NAD(P)H-dependent flavoenzymes (glutathione reductase, lipoyl dehydrogenase and ferredoxin-NADP+ oxidoreductase) can catalyze one electron reduction of metal ions such as chromium(VI) and vanadium(V) and simultaneously reduce molecular oxygen to generate Hi02 and, eventually, the ""OH radical. This finding is significant because (i) the known substrates for the flavoenzymes are organic species and not metal ions, and (ii) the report on the enzymatic formation of the ""OH radical provides a new pathway for understanding the mechanism of genotoxicity of some non-ferrous metal ions. For example, it has been suggested that OH radical is likely to be the major species responsible for Cr(VI) genotoxicity [1-5). The 'OH radical is generated through the reaction of Cr(V) complexes with cellular Hi02 [4,5]. Cr(V) itself is known to be generated from Cr(VI) in various biological systems, in particular, microsomes [ 6), mitochondria [7] and mitochondrial electron transfer chain complexes [8]. However, no specific enzyme responsible for the Cr(V) generation has been identified except possibly glutathione reductase [4]. In this study we have used ESR and spin trapping techniques to show that the flavoenzymes can generate Cr(V) and provide a catalytic redox cycle for 'OH formation in such reactions. Herein we present our results on Cr(VI) and summarize those on other systems. Correspondence address: N.S."

Jan 1, 1990

By Beatrice L. Lukens, David Schlain, John D. Prater

"The electrolytic manganese process developed by the Bureau of Mines4/ and now in use in the commercial plant of the Electromanganese Corp. at Knoxville, Tenn., and in the Bureau of Mines pilot plant5/ at Boulder City, Nev., involves the electrolysis of a solution of manganese sulfate and ammonium sulfate in a diaphragm-type cell. Metallic manganese is deposited on the cathodes, and sulfuric acid is produced at the anodes.. The spent electrolyte contains, in addition to the sulfuric acid, approximately 30 percent of the manganese and most of the ammonium sulfate originally present in the feed solution. This spent solution is used to leach fresh ore that has previously been given a reducing roast. The resulting leach liquor is purified and returned to the cell.Since the presence of small amounts of certain impurities in the electrolyte may be very detrimental to the electrodeposition of manganese, the purification of feed solution is a very important step in the process. According to the purification method6/ now in use in the Bureau of Mines pilot plant at Boulder city, Nev., cobalt, nickel, iron, arsenic, lead, copper, etc., are removed by precipitation as sulfides at a pH of 6.0 to 6.5. Residual sulfides and colloidal material are removed from the resulting solution by ferric hydroxide formed by adding a small amount of iron sulfate and passing air through the solution. Feed solution purified in this way contains less than 1/2 mg.-per liter-of such impurities as arsenic, iron, cobalt, nickel, copper, etc., and is pure enough to give consistently excellent manganese deposits.Although this purification scheme has given satisfactory results at the Boulder City pilot plant knowledge of the specific effects of various impurities would be valuable. Such information would be useful in diagnosing the causes of cell room operating difficulties, and might aid in the recognition and correction of impurity difficulties arising from the use of new ores.. The purpose of this investigation was therefore, to study the effects of various concentrations of some common impurities.Since the effects of some impurities may not be apparent during short deposition periods and since harmful impurities often cause erratic results rather than consistently poor ones, it was believed that conclusions concerning the effects of impurities should be based upon the results of a fairly large number of 20- to 24-hour tests. Because of the time required for such tests, it was necessary to limit the scope of the work to a few of the more common impurities."

May 1, 1946

By C. P. Fang

"For lower stages of multinozzle micro-orifice impactors, as many as two thousand nozzles are uniformly arranged within a cluster diameter of 1.06 inches. In the impaction region the mass flowrate of the spent air increases along the radius and reaches a maximum at the periphery. This crossflow can significantly deflect the air jets of the outer nozzles, hence the characteristics of impaction changes.Investigators in heat transfer and fluid mechanics have studied the influence of crossflow on jet deflection and found the dimensionless deflection of the jet centerline X/Dn is a function of (S/Dn)(l/m) . only, here X is downstream coordinate measured from the center of the jet orifice, Sis the jet-to-plate distance, Dn is the orifice diameter and m is the jet/crossflow mass flux ratio defined as:"

Jan 1, 1989

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius' has damped the vibrations so successfully that a short note concerning it is thought to be desirable. The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several modifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects. These modifications were suggested by careful study of the original idea embraced in the Julius construction. They were designed to give further constraint to motion in any direction other than that parallel to a line from the point of support through the center of gravity of the suspension, This was accomplished by making the suspended frame more rigid and by improving the means of adjusting each of the supporting wires to the same degree, thereby transmitting any impulse symmetrically through the three wires. The result was a suspension that is more effective, particularly for severe vibration, than the form described by Julius; also, it is believed to have advantages in stability, simplicity, and ease of adjustment over the few suspensions for this type of service that the author has found described in the literature.

Jan 1, 1931

By Walter T. Ackley

[The geophone has occupied a prominent position as a mine signalling device since its first introduction. The Bureau has carried out tests at different times with a view to improving the early geophones. The following paper describes briefly the adaption of the vacuum-tube audio frequency Amplifier to a new form of geophone. It is not intended to convey the idea that the results described are sufficient to warrant the drawing of definite conclusions as to the practicability of the electrical geophone, but the data and tests liven herein are made public because of their possible use to the industry and as a result of inquiries received as to the feasibility of such adaptions and modifications of the early geophones. Because of the limited time available to the authors, only one geophone with its auxiliary amplifier was constructed. As is well known, two geophones are necessary in order to determine the direction of a sound. Although the principles upon which the electrical geophone operates appear to be fundamentally correct, it is not possible to state whether two such devices 'rill function as efficiently, (as regards determining direction of sound) as the present geophone. In order to operate efficiently as a direction finder, the amplifiers of the electrical geophone must each amplify with exactly the same degree of magnitude. By proper design and adjustment this can probably be accomplished without greatly complicating the design. inasmuch as audio frequency amplification is used, no tuning; is necessary as is the case with tuned radio-frequency circuits. The same filament and plate batteries can be used to operate the amplifiers and by the use of dry cell tubes, requiring shall filament and plate currents, it if believed that a compact, portable and practical instrument can be evolved. Further investigations of the electrical geophone should be conducted to determine the points outlined in this preliminary report.]

Jan 1, 1924

Increase the safety of operators of front-end loaders by providing a means of monitoring the machine's stability. Approach Through a research contract, the Bureau of Mines developed a front-end loader stability indicator which provides the machine operator with a reliable, easily interpreted display assessing the stability of the machine. How It Works Statistics show that front-end loader accidents are the largest single category of machinery-related accidents in the surface mining industry. Many of the fatalities resulting from these accidents occur when front-end loaders rollover and either crush the operator who is trapped within the cab or strike the operator who is trying to jump to safety. Although rollover protective structures (ROPS) are required by law on front-end loaders to protect operators in the case of a rollover, these do not prevent the actual rollover from occurring. In fact, the operator has no way of evaluating the stability of the machine except by using personal judgment. The Bureau of Mines responded to this problem by developing a front-end loader stability indicator whose primary function is to Indicate to the operator when the machine is approaching an unstable situation which may trigger a rollover. The device bases Its interpretation on measurement of the normal loads on the machine's wheels. Strain gage instrumentation located on the machine is used to monitor the magnitude and change of forces acting normal to the front-end loader's wheels. These forces are direct indicators of the machine's center of gravity relative to its position on the ground. The strain gages are connected to electronic circuitry which amplifies and processes the signals. Stability or instability of the loader is relayed to the operator through a display of green, amber and red lights.

Jan 1, 1986

By Peter F. R. Altounyan, Paul B. Cartwright, John W. Cassie

This paper describes measured data on strata behavior obtained in recent years from sites in the United Kingdom and the implications for pillar design. The data include results from overcoring stress measurements adjacent to coal mine roadways and deformation monitoring related to longwall extraction. The stresses adjacent to mine roadways or entries have been measured at a number of coal mine sites in the United Kingdom. The results are analyzed with regard to the information they provide on pillar behavior and strength estimates. A reduction in stress consistent with yielding of the strata adjacent to the roadways is evident. This is consistent with the confined core model for pillar behavior. The pillar strength is dependent on the rate atwhich vertical stress can increase with distance from the pillar edge and hence the confinement provided to the yielded material. The measured data indicate a wide range in pillar strengths. Two groups of results are identified that show significantly different behavior corresponding to differing effective pillar strengths. Estimates of pillar strengths derived from the measured data for these two groups are compared with established equations used for pillar design. The differing behaviors and strengths are attributed to variations in the amount of yielding and deformation in roof and floor strata and hence in the amount of confinement they provide to the coal seam. Numerical modeling is used to provide a comparison with the measured data and to indicate that this provides a feasible mechanism to account for the measured data. As the depth of mining increases, pillars tend to become increasingly wide and squat. In such cases, it is possible for the surrounding roadways to become badly deformed and damaged while the pillars remain stable. The criteria of comparing pillar strengths and loads to establish pillar stability become less applicable in these circumstances; rather, considerations of roadway stability may be the limiting factor in determining suitable pillar dimensions. This is the case for pillar dimensions typically employed around longwall panels in the United Kingdom. Depending on the properties of the site and what are deemed to be satisfactory roadway conditions, this can lead to wide variations in required pillar dimensions. Measured data for deformations in roadways influenced by adjoining longwall workings are presented. These show that in some circumstances the influence of longwall extraction can be transmitted over large distances and confirm the variability in required pillar sizes depending on site properties.

Jan 5, 1999

Provide a means for continuous measurement and display of respirable dust concentrations in a mine so that when high dust levels occur, timely, corrective measures can be taken. Approach Develop a personal dust monitor that (1) is small and light enough to be worn by a miner, (2) has the capability to continuously measure the respirable fraction of coal dust, (3) will display the respirable dust concentration in mg/m3, and (4) can store the average respirable dust concentration and sampling time of several sampling shifts for later play-back. How It Works The personal dust monitor (PDM-1) uses light scattering and convection air currents to sample the respirable fraction of coal dust. Convective air currents cause dust laden air to pass through an open-celled sampling chamber (light sensing chamber). A near infrared light emitting diode (LED) located in the PDM-1 emits pulses of light. The pulsed light passes through a focusing lens and glass window into the sampling chamber. The light is then reflected, scattered, and refracted by the airborne dust particles. Light scattered within the angles of 450 to 900 (the angles within which the intensity of the scattered light is most closely related to respirable-size dust particles) passes through another window and is focused on a light detector. The light detector signal is amplified and presented as analog output voltage for conventional recording. This signal is also converted to a digital signal which the microprocessor uses with its crystal clock to calculate the 10-second average dust concentration, the shift average concentration, the time-weighted average concentration, and the elapsed sampling time. The microprocessor also stores dust concentrations of the seven most recent sampling periods, controls the operation of the LED and detector, and operates the liquid crystal display (LCD).

Jan 1, 1983

By Kenneth L. Cashdollar

This paper is an overview of and introduction to the subject of dust explosions. The purpose is to provide information on the explosibility and ignitability properties of dust clouds that can be used to improve safety in industries that generate, process, use, or transport combustible dusts. The requirements for a dust explosion are: a combustible dust, dispersed in air, a concentration above the flammable limit, the presence of a sufficiently energetic ignition source, and some confinement. An explosion of a fuel in air involves the rapid oxidation of combustible material, leading to a rapid increase in temperature and pressure. The violence of an explosion is related to the rate of energy release due to chemical reactions relative to the degree of confinement and heat losses. The combustion properties of a dust depend on its chemical and physical characteristics, especially its particle size distribution. In this paper, the explosion characteristics of combustible dusts will be compared and contrasted with those of flammable gases using methane as an example. These characteristics include minimum explosible concentration, maximum explosion pressure, maximum rate of pressure rise, limiting oxygen concentration, ignition temperature, and amount of inert dust necessary to prevent flame propagation. The parameters considered include the effects of dust volatility, dust particle size, turbulence, initial pressure, initial temperature, and oxygen concentration. Both carbonaceous and metal dusts will be used as examples. The goal of this research is to better understand the fundamental aspects of dust explosions.

By Richard F. Hewlett

An attempt has been made to fit assay data from an underground copper deposit to a three-dimensional polynomial surface as a means of expressing assay points in terms of their mine coordinates by a mathematical equation. The resulting equation was evaluated to predict the grade trend of the deposit. Although the fit obtained by this initial experiment is not considered accurate enough to provide good predictions about the deposit, the methodology is presented in this preliminary report to show the potential usefulness of the technique in mineral deposit evaluation. The technique also should be useful in determining the grade of blocks of ore for production scheduling and blending problems in open pit operations. Further experimentation is needed to increase the reliability of the computer program, to increase the precision of the method, and to make the solution more flexible for use on other mineral deposits.

Jan 1, 1964

By David F. Smith

The American Society for Testing Materials4 has recommended that the melting temperature of potassium chromate be used-for indicating the temperature to which a coal sample should be heated in the standard method of analysis to determine its volatile matter content. The specified temperature is 950± 20° C., the melting point of potassium chromate being noted as 940° C. Le Chatelier5 originally found the melting point to be 975°; later6 he found 9400. According to Shemtschushny7 the melting point is 984°; he also found a transition at 679°. Groschuff8 found the melting point to be 971° and the transition temperature 679°. Amadori9 reports a melting point of 9.78° and a transition point of 666°. The International Critical Tables10 take the melting point as 975°, which is estimated to be correct to two significant figures. In view of the apparent uncertainty existing, it has been though worthwhile to make a careful redetermination of this datum. It is of interest not only to determine the melting point of the pure salt, but also of the commercial product, in order to test its suitability for use as a temperature indicator. The work was suggested by A. C. Fieldner, chief engineer, experiment stations division, U. S. Bureau of Mines.

Jan 1, 1929

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

By R. L. Grant

[Detonators are used to explode permissible explosives, dynamites, or other high explosives. This explosion or detonation is brought about by the energy which is liberated as a combination of concussion and heat when the detonator is fired. In Other words; "The detonator is the key which unlocks the energy of a high explosive" (8)4. Being sensitive and latently dangerous, detonators must meet two primary requirements: They must be safe to handle and must detonate when desired, thereby imparting detonation to the explosive charge.]

Jan 1, 1941