Search Documents

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981

By J. W. Paul

This paper deals with the second phase of an extensive research on coal-mine ventilation factors. A comprehensive report of the entire work is in course of preparation, but abstracts of the various chapters are being prepared in order to make the results public as rapidly as possible. Part 1 dealt with the resistance of unobstructed entries and was issued as Serial 2621 of the Bureau of Mines, in July 1924. Description of tests. After the resistance of an unobstructed entry to flow of air had been determined by tests in the Experiment mine, mine cars were; run into the test section in various arrangements and the increase in resistance was determined. The cars used were of the wooden type with loose end gate, and would hold about one ton of coal, level full. They were 7 feet long. 4 feet 2 inches wide above the wheels, 3 feet high, and had a cross-sectional area of approximately 10 square feet. The average area of the entry was about 57 square feet, the ratio of unobstructed to total area being about 17.6 per cent. The track gage was 42 inches and the wheel-base 20 inches.

Jan 1, 1924

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By G. W. Reimers

Conditions in the underground mine environment can cause self-heating of sulfide ores as a result of exothermic oxidation reactions, which may result in mine fires. This Bureau of Mines report describes thermal analyses of finely ground chalcopyrite, chalcocite, galena, pyrrhotite, marcasite, and arsenopyrite, to characterize their responses under oxidizing conditions. Thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) were used, in the temperature range 1000 to 5000 C. Chalcopyrite showed an initial weight gain, due to formation of sul-fates, a weight loss, caused by ignition of iron sulfide to iron oxide, and a final weight gain, indicating the conversion of copper sulfide to sulfate. Chalcocite did not ignite in the temperature range studied but exhibited a rapid weight gain, because of the rapid conversion of copper sulfide to sulfate. Likewise, galena failed to ignite but underwent a steady weight gain when oxidized in a moist atmosphere, showing conver-sion of lead sulfide to sulfate below the ignition point. Marcasite underwent a rapid weight loss, indicating ignition, at 2000 C. Moisture in the oxidizing atmosphere lowered the ignition point of marcasite and arsenopyrite but not that of pyrrhotite. All the sulfides exhibited exothermic behavior at temperatures below the ignition point.

Jan 1, 1987

By H. W. Sohns

A retort was constructed in which fine particles of shale, entrained in steam or other gaseous media, could be retorted at controlled temperatures and residence times and the effects of retorting variables upon quality and quantity of products could be determined. Studies of the effects of temperature upon products obtained from Green River (Piceance Creek Basin, Colo.) and Chattanooga (Tenn.) oil shales were completed. The feasibility of using the retort to process a shale of extremely high moisture content from Brazil also was investigated. Air was used as the entraining medium in a series of studies in which combustion of some of the products of retorting within the retort tube supplied a major portion of the process heat. In another series, shale oil from a conventional retort was cracked thermally to obtain data for comparison with results of retorting en-trained shale. In still another series the effects of rates of steam flow and solids feed upon rates of heat transfer from the furnace to the process stream were studied. Crushed quartz rather than oil shale was charged to the retort in this series. A study was begun in which raw shale was partly retorted, the products separated, and the partially retorted shale recharged to the retort. The shale was to have been recycled until it was completely retorted in an effort to improve oil yield by recycle retorting; however, the project was terminated before the investigation was completed.

Jan 1, 1959

By Eliezer Kamon

To finalize the three years granted for the study of miners physiological responses to emergency situations, all the data obtained, were summarized into the following relevant sections; A.. Information on elements of the Man Test required under Subpart 4, Part 2, Title 30 in the Code of Federal Regulation (see Table M-T and Ref. I., Section A). B. Investigation on possible emergency activities, its simulation in the laboratory and the physiologic data obtained on miners performing them This included some studies under cool ambient conditions, expected to prevail in coal mines. C. While in section B the steady state responses have been obtained, time was devoted to establish a unit that will allow data gathering for non-steady state, i.e., transient responses to rapidly changing activities. Section B and C contained elements that were relevant to section A; the Man Test. Therefore some of the information described under section A Man Test, were actually measured during the battery of tests in either section B or in section C.

Jan 1, 1974

By James E. Hill

The Bureau of Mines has been carrying on an extensive diamond- drilling program during the past 7 years on deposits of strategic and critical minerals . Often the project reports and the drill-hole logs describe the findings only in terms of the mineral being sought at the time . Then , too , results may not always be interpreted alike by several mining engineers , and the cores therefore provide a permanent tangible record to complement the project reports . The cores from projects in the eastern divisions are being stored at the Mount Weather Testing Adit . Core from a representative hole ( or skeletonized sections from several holes , if these are more representative ) is selected at each project and shipped to Mount Weather for permanent storage . At the Testing Adit an underground room was prepared and storage racks were installed . Wooden core trays designed to accommodate cores of various sizes were purchased .

Apr 1, 1947

By R. G. Nelson

The mechanical properties of low-hafnium, arc-melted, Kroll-process zirconium are presented. The effect of temperature on the ultimate strength, yield strength, proportional limit, elongation, hardness, Young's modulus, electrical resistivity, and impact strength are shown, The effects of cold work and annealing on the tensile properties, bend radius, and formability, as determined by cupping tests, are also given, Tensile properties are compared, in part, to those obtained on earlier graphite-melted zirconium and on crystal-bar zirconium. INTRODUCTION The commercial production of high-purity, low-hafnium bearing zirconium has been achieved, and this metal is becoming available for industrial use. However, there is little published information regarding the physical and mechanical properties of this product; and, since there have been many improvements in the production and arc-melting techniques of zirconium in the past 3 years, it was considered advisable to present the properties of the vastly improved zirconium representative of current production.

Jan 1, 1954

By H. C. Loesche

The problem of signaling to the hoisting engineer from the cage in a shaft mine has been given considerable thought and attention by engineers and mine operators seeking to Increase the safety and efficiency of hoisting. HISTORY R. L. Rutherford,3/ an employee of the Magma Copper Co., Superior Ariz., realizing the need for a simple and practical moving-cage signaling system, began a serious of experiments early in 1937, Available electrical moving-cage signal in operation at this date required that signal wires be installed in the shaft to make a simple, positive signal without wires, the first experiments used the pipe lines in the shaft for carrying the signal current, but these experiments were not successful.

Jan 1, 1945

By Tilman M. M.

The effects of substituting cobalt for nickel on the acid corrosion resistance of two types of austenitic stainless steel were determined. Cobalt substitutions to a maximum 2.2 weight-percent were made in types 302 and 309 stainless steels. Total immersion corrosion tests were made in 10 volume-percent hydrochloric acid, and boiling-acid tests were conducted in 65 weight-percent nitric acid and in undiluted glacial acetic acid. For modified type 309 in acetic acid, corrosion rates decreased for additions greater than 0.57 weight-percent cobalt. Corrosion rates increased as cobalt was increased up to about 1 weight percent for modified type 302 in nitric and hydrochloric acids and for modified type 309 in nitric acid, but these rates decreased with a further increase in cobalt content. A gradual increase in corrosion rates with increasing cobalt content was shown for type 302 in acetic acid and for type 309 in hydrochloric acid. Cobalt substitutions in larger amounts (above a ratio of 8 Ni to 1 Co) may increase the corrosion resistance of the austenitic stainless steels.

Jan 1, 1965

By E. J. Gleim

For many years mining men have sought for a portable device that would be direct reading and permit more positive detection of methane than was possible with flame safety lamps, which depended so largely on the training, skill, and personal ability of the user. Through the years, after the discovery that methane contributed to many mine explosions, considerable effort and large sums of money have been expended in searching for and developing instruments that would be practical, and, at the same time, reliable and safe to use. Very early in the history of the Bureau of Mines, some of its engineers were unsuccessful, after many trials, in attempts to develop such an instrument. Commercial firms, however, persisted in research until today a number of instruments are on the market that have proved to be practical in coal-mine service. It is hoped, however, that further research will bring about improvements in accuracy and other desirable features. BUREAU OF MINES STANDARD FOR METHANE DETECTORS The Bureau of Mines recognized the need for establishing minimum requirements on which to base official approval of suitable Instruments. This standard was prepared as Schedule 8. It was revised before being issued in printed form. The revision was published as Schedule 8A in 1920 and was revised on two other occasions. The present edition, known as Schedule BC, was issued October 31, 1935.

Jan 1, 1954

By Edward W. Parsons

To determine in what part and to what extent creep or movement exists in an installed rock-bolt anchor and the effect of the creep or bleedoff on the tension load on a rock bolt, as well as the effect of normal mining activity on the rock-bolt load and anchor, the Bureau of Mines conducted tests in the laboratory and in two mines using four types of expansion-shell anchors, the wedge bolt, and in one mine, explosive-anchored rock bolts. Specially mounted heavy-duty springs, calibrated to obtain load readings from spring movement, were installed on the test bolts to prevent a drastic reduction in tension load caused by slipping or seating of the anchor. A dial gage, reading to 0.0001 inch, measured movement of the anchor shell against the rock and seating of the anchor wedge plug in the shell. While all bolts had electrical resistance strain gages for load reading, only readings from the laboratory tests were used because those from the field tests were erratic. The tests revealed that most load loss resulting from static loading is due to the slippage and seating of the serrations on the anchor shell into the drill-hole wall. Dynamic loading, primarily from sudden shocks from nearby blasting, and possibly from ground movement or mining activity, will cause the anchor wedge plug to seat in the anchor shell.

Jan 1, 1969

By Oliver Bowles

The United States Bureau of Mines has within its ranks a group of engi- neers who are engaged in working out quarry problems, the solution of which will be of general benefit to the industries involved. The problems undertaken are approached in a systematic and thorough manner, all the evidence for and against any proposed change or new development being collected as carefully as an attor- ney would prepare his data on an important case. Unlike the attorney, however, the Bureau engineer does not take sides; his judgment is based entirely and in- partially on the array of facts presented. In order to gain the desired infor- mation he visits many plants, consults with the leaders in the industry, works out experiments in his laboratory, and supplements this information with a stu- dy of all available literature already published on the subject in any part of the world. As an engineer who has for eight years conducted such inquiries in the stone industry, I propose to discuss the Bureau of Mines viewpoint; and it may be of interest to consider with me in a brief and general way the engineer's method of looking at quarry problems, and some of the results attained through past and present labors. While the Bureau has conducted no investigation directly for the crushed- st one industries, two years of investigative work at cement-plant quarries, and work now being conducted at lire-plant quarries, has a very direct bearing on the problems of the crushed-stone industry, since stripping, drilling, blasting, loading, and transportation are similar in many respects in all stone quarries. The results of cement-plant quarry investigations are to be found in Bureau of Mines Bulletin #160. (b) Two short papers on lime-plant quarry problems have been issued in mimeographed form as Serial #01 (c) and Serial 3 (d).

Jan 1, 1923

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By L. B. Pankratz

The heat content above 298.15° K was determined for crystalline vanadium silicide of the composition V3Si. This substance has a minor thermal anomaly (probably a heat-capacity maximum) near 560° K; the extra heat absorption is about 50 cal/mole. The original heat-content data are presented, and smooth values of the heat content and the corresponding entropy increments are listed for the temperature range from 298.15° to 1,500° K. Equations representing the heat- content values and derived heat capacities are also included.

Jan 1, 1963

Lower the respirable dust expo? sure of longwall shearer operators Approach Use improved water sprays on the shearer machine to direct the dusty air toward the face. In laboratory tests and actual mining conditions, the shearer-clearer has proved to be an effective dust control technique. Recent field experience however, has indicated that not enough technical information is available on proper installation of the improved shearer-clearer. This Technology News will provide details of the Improvements made to the shearer-clearer and provide guidelines for installing the system. How It Works The shearer-clearer system consists of several strategically-mounted water sprays and one or more passive barriers. The sprays redirect the airflow around the shearer into both a clean and a contaminated split. The sprays confine the contaminated split or dust cloud to the coal face, allowing the shearer operators to remain in the clean split on the walkway

Jan 1, 1986

By John C. Edwards

Carbon monoxide (CO) sensors are used in mine fire early-warning systems. Experiments were conducted by the U.S. Bureau of Mines with six diffusion-type CO sensors to determine their response to a reference CO concentration under both static and dynamic flow conditions. Static experiments were conducted with 0.5 L/min flow of 16 ppm CO in N2 through 8-and 12-L chambers. Dynamic flow experiments were conducted in two environmental chambers: One had directional flow capability of 1 m/s, and the second provided moderately nondirectional flow as high as 1.8 m/s. Reference CO concentrations of 13.5 to 19 ppm in air were used for the dynamic experiments. The results of the static experiments demonstrated that the sensors consistently underestimated the reference gas concentration. The dynamic experiment results showed the sensors provided reasonable agreement with the reference gas concentration when directional flow effects were not considered. Directional flow effects were evaluated for two sensors. One of the sensors showed a strong dependence upon the relative orientation of the diffusion tube with respect to flow direction. The second sensor did not show a dependence upon flow direction. The sensors' directional flow effect is significant for their proper in-mine utilization.

Jan 1, 2010

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By Lung Cheng

Based on earlier tests that showed steel to be much more likely to cause frictional ignition than tungsten carbide, the Bureau of Mines redesigned coal-cutting bits to reduce the hazard of face ignitions. Two bit designs--a mushroom-shaped bit with a conical shank and a dove-tail bit with a rectangular shank--are described, as well as bit wear tests conducted in the laboratory and in an operating coal mine. In laboratory tests, for 1/8-, 1/4-, and 1/2-in-deep cuts and cutting speeds of 280, 500, and 660 ft/min, the mushroom bit had significantly longer tip wear life than the conventional bit; the dovetail bit was also superior to the conventional bit. Results of in-mine tests on the mushroom bit agree well with laboratory results. In-mine tests of the dovetail bit are underway.

Jan 1, 1983

Minimize the effects of underground mine conveyor belt fires by developing methods to prevent automatic fire suppression system failures. The Problem Fire protection is achieved by prevention, early detection, and planned fire-fighting response. Automatic fire suppression systems are one form of planned fire-fighting response. When these systems are properly designed, installed, and maintained they can effectively control fires. Conveyor belt fires account for about 20% of underground coal mine fires. Fire protection requirements have been established for underground locations because of potential for start and spread of fire and the restricted personnel egress in a fire situation. Belt conveyor systems arc potentially dangerous because of the high fire incidence rate, high temperatures, dense smoke, toxic gases, and rapid flame-spread rate. While investigating the conveyor fire suppression problem, the Bureau identified automatic fire suppression system reliability as a potentially serious deficiency within the mining industry. Table 1 lists common failure modes fur three Fire suppression system types. This table summarizes findings of Mine Safety and Health Administration electrical inspectors responsible for inspection of belt protection automatic fire suppression systems. Batteries, contact points, control wires, and electric servocontrols are all prone to failure. Figure 1 shows rock-dust-contaminated relay contact points. This condition is dangerous because of the chance of intermittent failures, which might allow systems to pass annual functional testing, yet fail during actual fire emergencies.

Jan 1, 1989