Search Documents

By D. W. Frommer

Processing of nonmagnetic taconites by selective flocculation-des liming and anionic flotation of calcium-activated silica has been investigated using innovative procedures as a means of improving operating costs. Areas chosen for cost-cutting evaluation were grinding, fine screening, and water conservation and reclamation. The investigation was performed on Marquette range nonmagnetic taconites in the Bureau of Mines Twin Cities Metallurgy Research Center flotation pilot plant, at feed rates ranging between 900 and 1,100 lb/hr. With fully integrated water reclamation, flotation concentrates containing 65.8 percent Fe and 3.4 percent Si02 were made in the best operating period, with accompanying weight and iron recoveries of 40 and 74 percent, respectively. During this same period, the estimated cost of both flotation and water reclamation reagents was only $0.80 per ton of concentrate (1968 pricing basis). This cost is about 15 percent lower than obtained previously at this Center for flotation reagents only. The investigation demonstrated additional potential savings in operating costs of approximately $0.96 per ton of concentrate through autogenous grinding as a substitute for ballmilling. Fine screening of intermediate concentrates was employed advantageously, but the frequency of blinding may be a factor militating against use of the screen in this flotation system.

Jan 1, 1973

By D. E. Shanks

The Bureau of Mines surveyed a variety of inorganic ion-exchange materials to determine their suitability for removing valuable accessory elements and troublesome contaminants from metallurgical process and waste streams. Most of the materials, which included molecular sieves, heteropolyacid salts, and hydrous metal oxides, did not give adequate separations, did not have the necessary stability in strong acids or bases, or were not in a physical form suitable for ion-exchange use. Many of the suitable inorganic materials, especially the hydrous oxides, were capable of cation exchange with high capacity only in basic conditions, which caused hydrolysis of most of the cations tested. Multivalent anions, such as arsenate and phosphate, were easily removed from acidic solutions by hydrous oxides. Hydrous zirconia was the best material for this purpose. Multivalent anions were not easily des orbed because of compound formation; therefore, conventional ion-exchange techniques could not be employed. As an alternative approach, hydrous ferric hydroxide was used as a filter material to remove arsenate and phosphate from acid solutions. One gram of arsenic was removed from solution for each 20 g of ferric hydroxide. Ferric hydroxide is preferable to hydrous zirconia for use as a filter material because of low cost.

Jan 1, 1983

By T. O. Llewellyn

The Bureau of Mines, as part of its goal to develop technology that can conserve domestic mineral resources investigated beneficiation methods for recovering phosphate minerals from two Southern Florida deposits with high magnesium content. Chemical analyses of sized fractions indicated that no coarse pebble concentrate could be produced from either deposit. Conventional fatty acid-fuel oil batch flotation tests on two phosphate samples, analyzing 6.8 and 8.5 pct P205, yielded concentrates containing 28.97 to 29.80 pct P20S at recoveries ranging from 72.4 to 76.9 pct of the flotation feed. The MgO content ranged from 1.20 to 1.36 pct. Bubbling S02 gas through an aqueous concentrate slurry, further reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 pct, but with a concomitant loss in the phosphate recovery. Settling characteristics of slimes from both phosphate samples showed a slow settling rate, which is a typical characteristic of other slimes in the region.

Jan 1, 1981

By Alla D. Mah

The heat of combustion of TaC0.996 was determined by oxygen bomb calorimetry to be -302.8 ±0.4 kcal/mole. The corresponding heat of formation of TaC0.996 is -35.4 ±0.5 kcal/mole, and the calculated heat of formation of TaC1.00 is -35.5 ±0.5 kcal/mole.

Jan 1, 1965

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By Fred N. Kissell

This U.S. Bureau of Mines report is a guide for the control of air contaminants during tunnel construction. Topics discussed are calculating air quantity requirements, types of ventilation systems, planning ventilation systems, control of methane gas, control of dust, control of diesel emission, ventilation to remove blasting fumes, measuring airflow, and measuring gases. This report does not provide detailed design information, but seeks to answer practical questions on air contamination issues.

Jan 1, 1995

By Jack R. Woodyard

Scientists at the U.S. Bureau of Mines are studying iron aluminides as possible substitutes for stainless steels to reduce the Nation's dependence on imported strategic and critical materials. In a Bureau investigation on the mechanical properties of Fe-28Al, it was found that the material's machining properties were significantly improved at slow tool and feed speeds. Machining techniques normally used for brittle materials failed or were costly. Further experiments using a 5-in (12.7-cm) mill cutter with carbide inserts, operating dry at minimum machining speeds, produced visually smooth sample surfaces with no tool damage. As a result of these experiments and a review of published data on hydrogen embrittlement of iron aluminide under tension, non-water-based (e.g., sulfur-based) lubricants were chosen for production machining. Four-flute, 3/4-in (19-mm) carbide end mills were used at slow speed under lubrication. This latter procedure reduced tool wear and breakage by a factor of 2. Machined surfaces and specimen cross sections were analyzed by scanning electron microscopy to detect microcracking. Tensile tests gave the expected yield and ultimate strengths, indicating that no degradation by low-speed machining occurred. This study extends this work to show that the alloy can be machined at higher speeds using high-speed steel end mills, and that water-soluble cutting oil is a suitable lubricant and coolant.

Jan 1, 2010

By McHenry Mosier

The Anson Bette manganese mine, with two prominent manganese-bearing outcrops in schist, has attracted considerable attention for its variety of manganese minerals and its possibilities as a potential source of manganese. Little mining was done prior to 1925, when the present owner acquired the property, and operations since that date have been intermittent. Mine workings are open cuts with a maximum depth of 35 feet. The two outcropping ore deposits are irregular, pipelike bodies about 500 feet apart. As nothing was known of the grade or extent of mineralization in depth, four holes totaling 1,072.5 feet of bore Were diamond-drilled by the Bureau of Mines in the summer of 1943, with the results shown in figures 3 to 6. In.1945 a geophysical survey was run to map the magnetic anomalies in the manganese-bearing belt as a means of determining the locations of manganese deposits. Positive correlation of magnetite and manganese ore was not obtained.

Jan 1, 1949

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By Jr. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Laser-based instruments are used in areas where coal dust ignition presents a safety hazard. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory ~NIOSH, PRL! is conducting a study to help determine when an optical beam may be considered a potential ignition source in underground coal mines or coal storage facilities. Researchers conducted experiments to determine threshold igniting powers for Pittsburgh seam bituminous coal dust clouds using an 803 nm continuous wave laser. For fine sized coal dust dispersed in air, concentrations ranging from 600 to 2000 g/m3 were the most easily ignited. A heated layer of coal dust that deposited on the fiber tip during dispersion ignited the dust clouds. Minimum observed igniting powers for laser beams delivered by 200, 400, and 800 mm core fiber optic cables and directed into coal dust clouds were 2.0, 3.0, and 5.0 W, respectively. Threshold igniting power was proportional to beam diameter, and threshold igniting power density decreased with larger fiber diameters. Ignition delay times averaged 0.6 s and did not vary significantly with laser power under initially turbulent test conditions and with flammable targets. Comparisons are made with the results of other researchers.

By M. M. Tilman

The Bureau of Mines conducted research into the dispersion strengthening of lead by the coprecipitation method. Commercially available reagents in water solutions were reacted to form homogeneous precipitates of lead and aluminum compounds. The resulting precipitates were roasted to oxides and reduced in hydrogen to form mixtures of lead powder and alumina. The powders were isostatically pressed into billets which were extruded into rods. The rods were rolled into strip to provide material for testing. Alloys containing 0.5, 1, 2, and 3 nominal volume-percent A1203 were tested in short-time tensile tests and in tensile creep tests. An alloy of Pb-3 volume-percent A1203 exhibited an average tensile strength of 8,570 psi after rolling to 75-percent reduction at 125° C but had no measurable elongation. Alloys of lower A1203 content provided a better compromise between tensile strength and ductility. For example, an alloy of Pb-0.5 volume-percent A1203 had an average tensile strength of 6,590 psi with 9-percent elongation after rolling to 75-percent reduction at 125° C. Creep rates of dispersion-strengthened Pb-A1203 alloys were below 1 percent in 10,000 hours at stresses of 2,000 to 4,000 psi.

Jan 1, 1971

By J. T. McCartney

Thin sections of coal have been prepared for many years either by cutting on a microtome (1,2)5 or by grinding and polishing (2,1). Specimens of most coals had to be demineralized in hydrofluoric acid and softened in caustic solutions before they could be successfully cut with a conventional microtome. Some lignites could be cut without pretreatment. Jeffrey (1) obtained sections from coals of all ranks, although long and tedious pretreatment was required for anthracite. His sections were less than 1 cm.2 in area (probably much less for high rank coals) and about 5 microns thick. Thiessen (2) also cut sections of softened coals, mostly of low rank. His sections were a few square millimeters in area and about 3 microns thick. However, Thiessen preferred ground and polished sections for detailed studies because they were larger and had not been chemically attacked by softening media. He prepared ground sections as large as 4 cm.2 in area and usually 5 to 10 microns thick. Thousands of such sections, covering complete column samples of many coal beds, were studied for a number of years (4). With the development of the electron microscope and increased interest in quantitative optical studies of coals, a need for much thinner sections arose. However, no suitable technique for preparing such sections was known until Fernández-Morán developed a diamond knife for cutting ultrathin sections of hard materials (5). Workers at the Centre d'Etudes et Recherches de Charbonnages de France applied this new tool to the cutting of coal sections and have recently described their technique to the Burg, of Mines. Using their methods, with some modifications, researchers of the Bureau of Mines have succeeded in cutting ultrathin sections of coals ranging in rank from lignite to

Jan 1, 1961

By Ray J. Holmquist

"INTRODUCTION The Elk Mountain mica deposit was examined in June 1943 by the Bureau of Mines. An exploratory project and an access road for the property were recommended, provided the zinc was put in operation under competent management. K. Garard obtained a lease on the properly and started operations in June 1944; this was followed immediately by the Bureau's exploratory work. Road construction was begun by the Forest Service in July the same year.The lessee mined mica from the richest exposure with a crew of three men for 2-1/2 months. His operation terminated late in September, but the Bureau of Mines project and the Forest Service road construction continued until snow forced suspension of activity during the first week of November.The Bureau of Mines work consisted of trenching with a bulldozer, hand excavating on undeveloped outcrops, extending an existing adit, and starting a new adit below the older workings."

Jul 1, 1946

By M. Mahan, D. D. Blue, O. C. Garst, F. Fraas, L. Fink

"Early in World War II it became apparent that the known bauxite re- serves might not be adequate to supply the demands of the American aluminum-producing industry, as the transportation of bauxite from abroad to this country might easily be interfered with by hostile action. Consequently, the Bureau of Mines set up an intensive, well-integrated program for the production of cell-grade alumina from low-grade domestic ores. This pro-gram of investigation covered the production of alumina from clay, alumite, red mud, and other low- and marginal-grade ores. In line with the Bureau's usual policy of conservation of natural resources, it was decided that the investigation should be extended to cover the production of alumina and other valuable byproducts from aluminum dross.Statistical information showed that during the year 1943-44, an average of 2,900 tons of aluminum dross was generated monthly. This dross, after partial removal of free metal, had an average metallic aluminum content of approximately 9 percent. Some of this dross was produced by the melting of alloyed aluminum; but a large proportion 1,700 out of 2,900 tons - was generated by two producers of primary aluminum, and the dross did not contain an great proportion of alloying metals. Compared with dross from other sources, this 60 percent of the country's capacity can be assumed to have relatively uniform composition. Moreovcr, the problem of collection and distribution can be minimized because of the relatively small number of plants included in the organization of these two producers of virgin metal.Except for large pieces of metallic aluminum that easily can be mechanically separated for remelting, this dross has been discarded and scrapped. Inasmuch as chemical analyses show that the alumina content of dross is far higher-than ordinary ores - 111 percent alumina equivalent in dross compared to 57 percent alumina in bauxite - aluminum dross is a far richer source of aluminum than any known naturally occurring ores. The discard, of this waste material during the war and reconversion periods would be unsound economically. The work reported herein describes tests at the College Park Station of the Bureau of Mines on the recovery of metal, alumina, ammonia, methane, and abrasive-grade corundum from dross."

May 1, 1946

By Kenneth E. Hay

The Bureau of Mines collected coal and coal waste aggregate material from two different mine sites to determine their strength characteristics for use in concrete. The concrete would be placed underground as support walls for ground control in adverse conditions or unique mining applications. A standard mix design was established for a "wet" mix using a water-to-cement (w/c) ratio of 1.0 to facilitate pumping into place. Later, material was collected from four more mine sites and used to make 2-by 2-by 2-ft test blocks with the same w/c ratio. A pull-out cone device and borehole shear tester were used to determine the in situ material strength of the test blocks. These techniques will provide a simple and quick way of determining support wall strength in an underground environment. Test results from the pullout cone de-vice showed a good correlation of 0.98 to test cylinder compressive strengths of the same mix. Results of the borehole shear tester were inconclusive.

Jan 1, 1986

By K. J. Liles

The Federal Bureau of Mines conducts a comprehensive test program on clay and shale at the Tuscaloosa Metallurgy Research Center. All samples are subjected to standard preliminary ceramic tests, which include firing formed briquets at temperatures ranging from 1,000° to 1,250° C to identify firing range and colors, and quick-firing to determine bloating characteristics. Materials that shop potential as structural products are further tested after either extrusion or dry-pressing. If the quick-fire test is positive, bulk samples can be fired in a rotary kiln to evaluate their potential as light- weight aggregate A number of miscellaneous tests also can be conducted if requested. These tests determine properties such as refractoriness (pyrometric cone equivalency), oil-bleaching characteristics, oil absorbency, viscosity for drilling-mud applications, sand-bonding properties for foundry usage, and pelletizing characteristics.

Jan 1, 1977

In the last few decades, a considerable amount of effort was directed at accurately determining the coal pillar strength to use for safely designing coal mines. The outcome of this early work was the well known Obert-Duvall, Holland-Gaddy, Bieniawski, and Salamon-Munro equations for coal pillar strength. All of these equations were developed for, and were calibrated with, pillars in a large room-and-pillar area such that the loading could be determined using the "tributary-area" theory. In order to account for the abutment loads associated with full-extraction mining, the empirical methods have typically adopted a simple conceptualization of the abutment load through use of an "abutment angle." Short of a complete numerical or analytical analysis of the coal seam and surrounding strata, very little work has been Fretted toward refining the empirical analysis of pillar loading. It appears that the vast majority of the research has been directed at determining the pillar strength, the numerator of the safety factor equation, when the denominator of the safety factor equation, the pillar loading, plays an equally important role in pillar design. This paper will address the deficit of pillar loading research by exploring the accuracy of the empirical abutment load calculations using insight provided by an elastic overburden model, a laminated overburden model and field observations. Ultimately, it is determined that a constant abutment angle probably over-predicts the abutment load as the mining depth increases.

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961