Search Documents

In the interest of safety in metal mining, the Bureau of Mines recommends: That underground metal mines be equipped with a main fan in a fireproof housing, located preferably on the surface. The fan installation should be designed to ventilate the mine adequately throughout and to permit prompt reversal of direction of air flow. Many metal mines depend for ventilation upon natural flow of air, assisted by the exhaust from pneumatic drills and by compressed air blown into the workings. Others also ventilate separate headings or sections with fans and blowers. Relatively few have o mechanical ventilating system that controls the coursing of air throughout the mine.

Jan 1, 1939

By H. G. Iverson

Solid state reactions of manganese with silica were investigated in high-temperature tests. Reactions of 0.5 to 4.0 moles manganese (Mn) with 1 mole silica (SiO2) at 1,100° C and of 2.0 Mn:SiO2 mole-ratio mixtures at 1,000° to 1,150° C yielded products consisting of a slag phase and a metallic phase. At 1,100° C, the slag phase from reactions of the low Mn:SiO2 mole-ratio mixtures was composed of SiO2 and rhodonite (MnSiO3), and the slag phase from the high Mn:SiO2 mixtures was composed of MnSiOs and tephroite (Mn2SiO4). The metallic phase from the corresponding low Mn:SiO2 mole-ratio reactants consisted of two manganese silicides, Mn5Si3 and Mn3Si; from the high Mn:SiOg mixtures, it was Mn and the manganese silicide (Mn5Si). For the higher mole ratios of MnSiO2 the manganese content in the metallic phase increased, while the manganese and silica contents of the slag phase remained nearly constant. The slags did not contain free or uncombined manganese oxide (MuO). For the 2.5 to 4.0 Mn:SiO2 mole-ratio mixtures reacted at 1,100° C, the maximum quantities of silica reduced and of the manganese in the slag appeared to become asymptotical at about 41 and 48 percent, respectively. A brominating procedure was developed that was highly selective in removing the metallic constituents from the reaction product, leaving the slag phase as residue. X-ray diffraction patterns were obtained on prepared silicides Mn5Si, Mn3Si, and MnSi.

Jan 1, 1967

By P. E. Churchward

The Bureau of Mines developed a process using amines for recovering tungsten as ammonium paratungstate from alkaline leach liquors without producing synthetic scheelite as an intermediate product. Over 90 pct of the tungsten in low-grade scheelite or ferberite concen-trate was recovered as ammonium paratungstate by (l) autoclave leaching the concentrate with Na2CO3, (2) solvent extraction of the acidified leach liquor with kerosine solutions of either a quaternary amine (Aliquat 336) or a primary amine (Primene JM-T), (3) stripping the tungsten values from the quaternary amine with ammoniacal NH4C1 or from the primary amine with NH4OH, and (4) crystallization of ammonium paratungstate from the strip liquor. Reagent consumption in pounds per pound of W03 recovered was, for the quater¬nary amine, 3 Na2CO3, 3.5 H2SO4 , 2.2 NH4Cl, 1 NH3, and 0.4 glacial acetic acid; for the primary amine, it was 3 Na2CO3, 3.5 H2SO4, .06 NH4Cl, and 0.9 NH3. Both reagents extract molybdenum along with tungsten. Silicate and phosphate are partly extracted and contaminate the product; leach liquors containing these impurities require preliminary purification.

Jan 1, 1966

By H. Dolezal

A laboratory study of acid-ferrous sulfate treatment of low-grade manganese ores from the Cuyuna range, Minnesota resulted in 93-percent extraction of manganese as manganese sulfate with consumption of 3.8 pounds of H2S04 per pound of extracted manganese. Two types of ore were treated in consecutive stages. The first are contained carbonate minerals of manganese and iron, both soluble in H2S04 solution. The second ore contained manganese oxide minerals, insoluble in straight acid solution but soluble in the ferrous sulfate solution obtained from treating the first ore. Leaching data were obtained by countercurrent percolation of coarse (minus-1/2-inch) ore particles at room temperature and by agitating minus-65-mesh ore particles in heated solution. Extraction of manganese and acid consumption were the same, but the percolation leach required 6 days compared with 1 hour for hot agitation. Variations in the size of ore particles treated, leaching time, acid concentration, solution temperatures, and method of applying ferrous sulfate solution to the oxide ore were studied. The effects of several reagents for removing iron from solution and improving filtration were also studied.

Jan 1, 1959

By R. P. Vinson

The Bureau of Mines evaluated two real-time light-scattering dust monitors by measuring their response to Pittsburgh Seam coal dust and Arizona road dust (ARD). Both monitors, the model PDS-l, a personal dust sensor, and the model PCD-l, a digital dust indicator, are made in Japan by Sibata Scientific Ltd. Tests were conducted inside a laboratory aerosol chamber designed to maintain a uniform spatial distribution of the test dust. PDS-l and PCD-l measurements of concentrations for each test dust were averaged over 4-h test periods and compared with simultaneous gravimetric measurements. Both dust monitors responded linearly with mass concentration with both coal dust and ARD. However, the linear response of the PDS-l differed from that of the PCD-l for both dusts.

Jan 1, 1987

By D. H. Chambers, Arnold M. Lansche

Electro recovery by amalgam methods was investigated to determine the feasibility of recovering pure cadmium from cadmium sponge produced during purification of zinc electrolyte at electrolytic zinc plants . Actual material used in this work was air- oxidized cadmium sponge . An acid rinse and zinc displacement technique was developed to amalgamate this oxidized cadmium . ( In - plant use of the recovery process would probably not require this step because of the fresh state of the sponge . ) Zinc was completely removed from amalgamated sponge by selective oxidation with air . Zinc - free cadmium amalgam was circulated by an electromagnetic pump through an electrolytic cell where cadmium of 99.9+ percent purity was electrodeposited onto a rotating aluminum cathode . Polarographic methods were developed for determining cadmium and zinc in mercury and in sulfuric acid solution .

Jan 1, 1964

By J. B. Gayle

Both immediate and long-range economic factors are associated with blending anthrafines to produce metallurgical cokes, and they warrant careful consideration of the technology of carbonization of blends containing significant proportions of inert substances in general and anthrafines in particular. This situation has resulted in numerous publications dealing with various phases of the overall problem, particular emphasis being placed on the effects of inert substances on the yields and quality of cokes produced. Because relatively little attention has been given to the expansion behavior of coal blends containing inert substances, an investigation of this problem was undertaken using the Bureau of Mines sole-heated oven. Since experiments in the sole-heated oven do not measure wall pressures directly, a new method of interpretation of sole-heated oven data, which permits estimates of wall pressures, has been proposed.

Jan 1, 1955

By P. G. Barnard

The Bureau of Mines investigated the effects of various additions of rare-earth metals or rare-earth oxides on the mechanical properties of cast and wrought plain-carbon steels. Rare-earth metals, as misch metal, were added to medium-carbon steel in amounts to 0.70 weight-percent; rare-earth oxides, as a commercial mixture, were added in amounts to 1.50 weight-percent. The melting and casting of conditioned steels were done in a vacuum-induction furnace, to avoid formation of oxides from the melting atmosphere and to pro-vide better control over chemical composition. At room temperature, data for tensile strength, yield strength, elongation, and hardness of cast and wrought steels were obtained by standard testing equipment and procedures. Impact tests were conducted on as-cast steel specimens. The greatest amount of tensile ductility and impact strength was obtained in as-cast steel with 0.50 to 0.70 weight-percent misch metal additions. No significant improvement on mechanical properties was indicated in wrought steels containing rare-earth metal additions in the range from 0.10 to 0.70 weight-percent. In general, the rare-earth oxide additions up to 1.50 weight-percent had little effect on the tensile properties of steel in the cast, wrought and annealed, or wrought and normalized condition.

Jan 1, 1967

By Laurance L. Oden

The Bureau of Mines studied three processes for preparing NaAl(OH)2C03) the intermediate compound which is calcined to produce alkalized alumina: (1) Mixing of Na2 C03 and of A12 (S04)3 solutions, (2) digestion of aluminum hydroxide in solutions of Na2C03 and NaHC03 at 90° C, and (3) addition of CO2 at 25° C to caustic solutions of aluminum to precipitate aluminum hydroxide followed by digestion at 90° C. The first process had the highest raw material consumption and washing requirements, and successful application of process 2 depended upon the availability of active aluminum hydroxide. Process 3 was the most effective, considering both process technology and raw material requirements. Procedures were also investigated for washing, filtering, drying, and calcining precipitates. Analytical methods included X-ray diffraction, atomic absorption spectroscopy, differential thermal analysis, and thermogravimetric analysis.

Jan 1, 1969

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

By C. E. Jordan

The fundamental properties of dielectric separation were studied to provide insight into the design and operating characteristics of a dielectric separator. Force equations on mineral particles were derived and evaluated experimentally. Responses to variations in the electrical voltage and frequency, feed rate, particle size, dielectric fluid, and dielectric constant were tested theoretically and experimentally, using a 5-cm-diam dielectric separator. High-dielectric mineral recovery was proportional to the calculated effective dielectric force volume (EDFV) that surrounded each drum-electrode wire. Electrode spacing was the most sensitive design parameter; spacing of less than 0.4 cm was required for a good separation. Dielectric separation was effective for separating minerals with dielectric constants that differed by approximately 2 or more.

Jan 1, 1985

By John S. Berber

Olefin and paraffin mixtures (C10-C16 and C10-C22) were separated from low-temperature lignite tar by urea adduction and sulfated to yield secondary alkyl sulfate detergents. The C10 ?C16 secondary alkyl sulfate showed a 99.3 percent biodegradability, and the C10-C22 fraction showed a 96.8 percent biodegradability, exceeding the required standard of 80 percent for the biodegradability of anionic detergents in washing and cleaning compounds. Chlorination of paraffins yielded a detergent of 93.2 to 93.4 percent biodegradability.

Jan 1, 1968

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

By Robert J. Timko

Water-jet-assisted cutting involves the use of a mechanical cutting bit in combination with a high-pressure water jet directed just in front of the bit tip. Such a jet can offer benefits in terms of improved cutting, reduced dust and fines, and improved bit wear. The Bureau of Mines, through a contract with the British National Coal Board, has re- searched the use of water-jet-assisted cutting on roadheaders. After several engineering design problems were overcome, this program led to the successful underground testing of these roadheaders. Today, more than 60 water-jet-assisted roadheaders are in operation around the world, and numerous others are on order. This paper details the evolution of these machines and the benefits to be gained by their use.

Jan 1, 1986

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975

By John P. Capp

Addition of sintered fly-ash/bottom-ash mixtures to rubber formulations failed to increase the skid resistance of the resulting products. Wear, tensile and hot-tear strengths, and resilience of the ash-rubber material, as determined in laboratory tests, were significantly less than that of comparable rubber. The material appeared unsatisfactory for automobile and truck tire manufacture, but might prove suitable as a filler in other rubber goods. Raw fly ash could not be satisfactorily compounded with rubber.

Jan 1, 1972

Objective To develop and evaluate the effectiveness of safety training tools specific to the underground hard-rock mining industry. Background Scaling, the removal of loose rock from the roofs and walls of a mine by manual or mechanized means, may be necessary during any stage of mining. Manual scaling is very labor intensive, and mechanical methods can be too powerful and actually produce a less stable roof.

Jan 1, 2001

By M. J. Kovalik

Illinois No.6, a high-volatile B coal of low fluidity, was blended with fluidized-bed char and coke breeze to improve the strength of the coke obtained from carbonizing this coal. Twenty-one tests, selected from those made in the small-scale Hanson carbonizer, were carbonized in the BM-AGA 13-inch-diameter, cylindrical retort, with a coal charge of about 90 pounds; the strength of the cokes was determined by the standard ASTM tumbler test. Using the same procedure, 10 tests were made with High Splint, a high-volatile A coal from Harlan County, Ky. Carbonization of the blends produced larger and stronger cokes than did the Illinois No.6 coal singly. The optimum blend contained 6 percent each of char and coke breeze. Further improvement in coke strength was realized by either preheating this blend prior to carbonization or by adding a small pro-portion of a premium blending coal. The former method could possibly eliminate the use of premium coking coals in blends with Illinois No. 6 coal to make an acceptable metallurgical coke. Except for no improvement in coke strength by preheating, results for High Splint coal showed behavior similar to that of the Illinois No.6 coal.

Jan 1, 1973

By M. D. Carver

The purpose of this investigation was to determine the effects of variations in content (near the residual level) of the impurities aluminum, nitrogen, manganese, and copper on the corrosion rate in pressurized hot water and in pressurized steam of zircaloy-3, a zirconium-base alloy of 0.25 percent tin and 0.25 percent iron. Thirty-five 10-pound ingots were cast with the appropriate additions of impurity elements, and these were converted to wrought sheets. These specimens were then tested both in water and in steam. The analysis of the resulting data showed that in environments of either pressurized hot water or superheated steam, corrosion rates increased with increasing content of aluminum, nitrogen, or manganese, but were not affected by variations of copper. The effects of aluminum and nitrogen were found to be greater than the effect of manganese. INTRODUCTION At the request of the Atomic Energy Commission (AEC) in August 1956, the Federal Bureau of Mines, in cooperation with Bettis Plant of Westinghouse Electric Corp., began investigating the effects of certain impurity elements on the corrosion rates of zircaloy-3 in pressurized hot water and in pressurized steam. It was necessary to know these effects in order to set control limits on residual impurity levels in zirnaloy-3, intended for heat transfer service in the nuclear reactor of the pressurized water type. A factorial expert it was designed by Westinghouse statisticians. The Atomic Energy Commission provided raw zirconium sponge purchased from Wah Chang Corp. The Bureau's laboratory at Albany, Oreg., made material of different combinations of impurity levels and subjected the material to corrosion tests. This report will describe the work done at the Bureau laboratory and will show, quantitatively the effects of different residual levels of aluminum or nitrogen, or manganese or copper on corrosion rates.

Jan 1, 1961

By M. B. Shirts

Bench-scale studies were made on a reductive hydrometallurgical procedure to convert chalcopyrite flotation concentrate to copper metal or a readily leachable sulfide. Reductive conversion of chalcopyrite and dissolution of iron and sulfur were accomplished in hydrochloric or sulfuric acid solution by the addition of metallic copper, iron, or lead. Use of metallic copper as the reductant enabled extraction of 95 and 46 percent of the iron and sulfur, respectively. The products were ferrous iron, hydrogen sulfide, and a copper sulfide. Use of metallic iron or lead as the reductant enabled extraction of 95 percent of both the iron and sulfur. The products obtained with metallic iron or lead were ferrous iron, hydrogen sulfide, and metallic copper.

Jan 1, 1974