Search Documents

By Philip C. Tully

The Bureau of Mines, in a continuing effort to improve processes and methods of helium purification, has developed a differential distillation method for removing helium-3 from helium-4. Differential distillation at 4.2 to 1.6 K was used to reduce the helium-3 in helium-4 from about 200 to less than 1 part per billion. The results from four stills ranging in size from 1 to 25 liters are reported. The method has the potential to be adapted to commercial-scale separations.

Jan 1, 1975

By P. B. Lorenz

Wettability measurements and laboratory waterflood tests were compared under a wide variety of conditions. Experiments were conducted with synthetic and natural crude oils, treated and untreated outcrop and oilfield sandstone cores, and synthetic brines with and without caustic, detergent, or phosphate additives. Measurements were made on equilibrated and unequilibrated systems at 77° and 150° F. Wettability was evaluated by the Bureau of Mines method from capillary pressure curves determined with a centrifuge. The waterflood data were fitted by empirical curves; the parameters of the curves characterize primary and subordinate production and also give the ultimate oil recovery. Results showed that wettability measurements at 77° F were useful predictors of recovery efficiency in waterflood tests run at both temperatures. Oil recovery in the early stages of waterflooding increased with increasing water wettability; however, the ultimate recovery was highest at a slightly oil-wet condition. The oil displaced at highest speed in the centrifuge was correlated with ultimate recovery in waterflood tests. Chemical additives to the brine sometimes lowered wettability and also sometimes improved waterflood recovery, but wettability and recovery were not correlated with additives present. The effect of additives on recovery in waterflooding was best seen in water-oil ratio curves.

Jan 1, 1974

By L. B. Pankratz

The Bureau of Mines conducted heat-content measurements above 298.15° K for dehydrated analcite (NaAISi2O6) to 1,000°K, kaliophilite (KA1Si04) to 1,800° K, and leucite (KAlSi206) to 1,800° K. Heat content and entropy increments were tabulated, and the heat content data, were given in equation form. A first order transition was noted for kaliophilite near 810° K with a heat absorption of 160 cal/mole. Leucite had a second order transition which became complete near 955° K. In this transition a crystal change occurred from tetragonal (low-temperature form) to cubic (high-temperature form).

Jan 1, 1968

By Edward D. Thimons, Jay F. Colinet

NIOSH conducted a strategic planning effort to identify those areas in mining with the greatest research needs. Data analysis and stakeholder input identified the need to reduce worker exposure to respirable crystalline silica dust as a high priority area. MSHA dust sampling data were analyzed to target the mining commodities and occupations with the greatest percentage of samples containing silica above compliance levels. In response, the Pittsburgh Research Laboratory (PRL) has implemented a multi-faceted research program to improve silica dust control for these problematic commodities and occupations. A review of silica compliance trends, PRL silica research programs, and recent control technology developments are provided here.

By Kevin Connor

Exports of agricultural products, mostly coffee, continued to account for more than 90% of Burundi's foreign exchange revenue. The country's ban on commercial mining was lifted in 1987. Mining of peat for fuel, limestone for agriculture, and clay for insecticides continued as in previous years. At yearend, Burundi's external debt stood at almost $700 million.2 Amoco Burundi, a subsidiary of the Amoco Petroleum Co., drilled two exploration wells in northern Lake Tanganyika in 1987. No oil was found, but preliminary findings were encouraging enough that further seismic surveys and offshore and onshore drilling exploration were planned in 1988. Any oil or gas finds would have substantial impact on the Burundian economy because a major portion of the country's trade deficit was directly attributable to petroleum and gas imports. The Zaire Government agreed in June to let Amoco Burundi explore Zaire's side of Tanganyika using the same equipment and personnel being used in Burundi.

Jan 1, 1989

By C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By Charles E. Munroe

On March 14, 1921, an explosion occurred at about 6:15 A.~. on the premises of an iron-mining concern throug:1 which two magazines, one containing upwards of 9,000 pounds ot a high explosive of the dynamite class, and a second, 60 feet distant, containing upwards of 10,000 No. 6 detonators, were completely destroyed, and a ncratertt,? f3et deep by 30 feet in diameter, was excavated in the gro~ at ~he place whare the mag~iine containing the high explosive had been lo~ated. As a rule any eye wit~esses to the circumstances im.~ediataly preceding and d(irectly concurrent with a.c.ci.:lental ex;losions ar.e victims of s11ch explosions, and, therefore, the conclusions reached as to the cauoa. of such explosions must, perf'orce, be based aln:ost completely on circumstantial evidetJ.ce. In this iii.stance, b:ecause both the explosive and detonators were of -orov{:;d: character; because of the time of the day and the state of operations iit the·· time of the e:.q,losion; because the rerroteness of the location of the n:-1agazi::1es 1 0::1 the side of a ravine, easily admittfi of unobserved approach; beca:iise differencas existed, and because no obvious cause was at once apparent, there arose suspicfon that the explosion was not accidental.

Sep 1, 1921

Active and abandoned mine sites can be an irresistible- - and sometimes deadly - - draw for outdoor enthusiasts, particularly children and young adults. Despite repeated warnings, posted signs, and fencing, tragedies involving accidents on active and abandoned mine property continue to make headlines, especially with the arrival of warmer weather and the summer months ahead. Over the last few years, there have been dozens of tragic incidents involving children and adults ventur­ing onto active and abandoned mine property. They include: A 16-year-old youth suffered fatal injuries after his all-terrain vehicle became airborne in an accident at a gravel mine near Albany, New York. A young boy was electrocuted when he contacted a high-voltage power line while sliding down a stockpile at a sand and gravel mine in Grand Island, Nebraska during its off-shift hours.

Jan 1, 1999

By T. H. Jeffers

Significant amounts of cobalt are present in readily accessible spent copper leach solutions. The Bureau of Mines investigated the feasibility of extracting cobalt from these solutions in a multiple-compartment ion-exchange (MCIX) column. The effects of aqueous flow rate, resin flow rate, column height, and compartment height on cobalt extraction were determined. Cobalt extractions of 92 pct or higher were achieved at solution flow rates of up to 5.5 gpm/ft of column cross-sectional area and an aqueous-to-resin flow ratio of 40:1. Overall cobalt extraction increased as the column height increased, but cobalt extraction per unit of length was more efficient in 8-and 12-ftco1umns than in an 18-ft column. Solvent extraction procedures were utilized to purify and concentrate the MCIX column eluates and produce a cobalt sulfate solution containing 70 to 80 giL Co. Metallic cathodes containing over 99 pct Co were e1ectrowon from this solution. Zinc, nickel, and copper byproducts were also recovered during processing of the ion-exchange eluates. Estimated total capital cost for a commercial-scale 10,000 gpm of a spent leach solution containing 26 million. With credits for zinc, nickel, and copper estimated net operating cost was $9.36/lb Co.

Jan 1, 1987

By Charles L. Kimbell

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not wholly devoted to mineral commodity transport, as seen in tables 16 through 22. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to non mineral goods, as well as carrying mixed mineral commodities and non mineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-off ships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Table 16 shows the distribution of the world's merchant fleet by vessel type in terms of the number of vessels, their gross tonnage, and their deadweight tonnage. The increase of nearly 1.5 % in the number of vessels between 1990 and 1991 compared with a 2.7% growth in gross tonnage and a nearly 2.3 % increase in deadweight tonnage points to an increase in the average size of vessels. Of the four categories of vessels reported, all showed increases in number and in deadweight tonnage between 1990 and 1991 except for "other," and on the gross tonnage basis, all groups registered increases. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1993

By W. H. Eddy

Laboratory batch and small-scale continuous flotation tests were con-ducted by the Bureau of Mines on a mica waste tailing from Kings Mountain, N.C., to determine the feasibility of producing high-quality mica, feldspar, and glass sand. Mica was recovered by two methods; one was by flotation in an alkaline circuit, which produced a mica concentrate assaying 92.0 percent mica with a recovery of 87.l percent, and the other by flotation in an acid circuit, which produced a mica concentrate assaying 91.0 percent mica with a recovery of 79.4 percent. Continuous flotation processing yielded a feldspar concentrate assaying 1.10 percent Na20 and 13.50 percent K20, with recoveries of 66.4 and 80.6 percent, respectively. The feldspar tailing was high-quality quartz glass sand analyzing 98.6 percent Si02 and 0.02 percent Fe203.

Jan 1, 1969

By George J. Carter, George H. Todd, Hal J. Kelly

In July 1956, the Bureau of Mines and the J. R. Simplot Co. participated in evaluating and beneficiating drill-hole samples from the Bovill, Idaho, clay-silica deposit and in tests of the beneficiated products. The geology, mineralogy, beneficiation, and potential uses of the clay and quartz fractions of the Bovill deposit are described. Test work showed that a filler-grade clay having an apparent spectral reflectance of 78 percent can be made by bleaching, and by removing some of the submicron-size particles. A quartz product suitable for the manufacture of glass containers can also be made.

Dec 1, 1963

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

By J. D. Sargent

Selenium might be described as a paradoxical element, being a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden.

Jan 1, 1954

By Mark Larson, Doug Tesarik, Joe Shoemaker, Brad Seymour

In cooperation with Cyprus Twentymile Coal Co., researchers from the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, conducted a study at the Foidel Creek Mine, an underground coal mine near Oak Creek, CO, to evaluate the stability of underground working conditions as a longwall advanced through a series of backfilled cross-panel entries. Instruments installed in the cross-panel entry pillars, backfill, longwall panel, and adjacent headgate entry were continuously monitored by a computerized data acquisition system as the longwall approached and advanced through the backfilled section of the panel. Data collected from these instruments were analyzed to determine the magnitude and direction of the secondary principal stress changes ahead of the longwall face, deformation and closure of the headgate entry, and stability of the cross-panel entry pillars and backfill. A three-dimensional, boundary element model was calibrated to accurately predict mining-induced stress changes and the distance they occurred ahead of the longwall face. As the longwall advanced through the backfilled entries, most of the mining-induced load was supported by the cross-panel entry pillars. The backfill provided stability for the roof and floor of the in-panel entries and also confined the entry pillars significantly improving their load-carrying capacity. Comprehensive information derived from backfill material property tests, instrument data, underground observations, and numeric modeling results document the safety and stability of the 8-Right mine through and should provide beneficial case study information for other longwall backfilling applications in the future.

Several short color films describing new technology developed through Bureau of Mines research are available on a loan basis. The films review results of Bureau research programs aimed at aiding the minerals industry by increasing mine productivity, ensuring worker health and safety, and enhancing minerals recovery, processing and recycling. Most of the films are available in a choice of for mats: 16mm film, ½" VHS cassette tape, or ¾" U-matic tape. The films are loaned by the Bureau of Mines free of charge; borrowers are requested to pay only the return postage and for any damage to the films. All titles are also available for purchase in 16mm or videotape formats. Interested persons wishing to borrow or purchase a film should specify its title and the preferred and alternate showing dates. All requests should be addressed to: Motion Picture Library Bureau of Mines Cochrans Mill Road P.O. Box 18070 Pittsburgh, PA 15236 A short description of each film follows: Safer Coal Mining Equipment Traces the development of modified conventional and continuous mining equipment, beginning with an investigation of the problems encountered with mining equipment and continuing through long-term testing of the modified equipment in two mines. "Human engineered" coal mining machines are shown in operation. These machines include features such as adjustable cabs, easy access controls, improved illumination, and other safety improvements. (19 min)

Jan 1, 1986

Improve the field-of-view into the front-right blind spot for drivers of large haulage trucks, thereby reducing the growing collision hazard in surface mines. Approach Reduce the glare problem found in the first generation fresnel lens blind area viewer design by eliminating the upward-looking section of the fresnel lens and adding a rear hood to reduce backlighting. How It Works The first generation blind area viewer was developed and in-mine tested as an aid to improved visibility for large haulage trucks. Other aids were improved left-and right-hand mirrors. Evaluations showed that a blind area viewer mounted on the right-front of the radiator deck was effective and was readily accepted by drivers. Nevertheless, because glare was a problem under certain conditions, a low-profile viewer was developed. Glare control louvers from the earlier design were kept and a backlighting glare control hood was added. The height of the hardware was reduced by eliminating the top three inches of the fresnel lens. This portion of the lens contained an upward-looking segment which originally was thought to be needed so the driver could see the horizon when he looked through the viewer and be better

Jan 1, 1982

By D. E. Shanks

The Bureau of Mines investigated the effects of HCI concentration and solution temperature on the solubility and crystal form of the chlorides of Co, Mn, and Ni when sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increasing HCI concentration in solution caused the chlo-rides of Co, Mn, and Ni to crystallize (salt out) because of the common ion effect. The salting-out crystallization was most effective for NiCI2, which had a solubility of 0.7 pct at 20° C and maximum HCI concentration. COCl2 salted out to a minimum solubility of 9.4 pct at 20° C and 22 pct HCI concentration and increased in solubility at greater HCI concentrations because of the formation of chloride complexes. MnCl2 was intermediate in behavior. The effect of temperature on solubility was greatest for CoCl2 and least for NiCI2, 15 and 7 pct change, respectively, over the temperature range of 20° to 60° C. The salted-out chlorides of cobalt and nickel formed the hexahydrates and those of manganese formed the tetrahydrate in saturated metal chlo-ride solutions at 20° C and low concentrations of HCI. Increasing the temperature or the HCI concentration caused a 108s in waters of hydra-tion. At 60° C, the salted-out crystals of NiCl2 formed the tetrahydrate in HCI concentrations up to 18 pct and the dihydrate at higher concentrations, while cobalt and manganese chlorides formed the dihydrates, even in water.

Jan 1, 1985

By C. E. Jordan

The Bureau of Mines conducted laboratory studies on methods to increase the recovery of brine from slime produced by operating potash plants. The slime was comprised of 80 percent brine saturated with KCl and NaCl, and 20 percent solids. A variety of settling techniques, filtration methods, continuous centrifugation, and novel processing techniques were investigated. Vacuum filtration recovered 6S percent of the brine at 47 gallons of brine per square foot per day. Pressure filtration, on the other hand, recovered 74 percent of the brine at 40.9 gallons of brine per square foot per day. Centrifugation in a 6-inch-diameter continuous decanter-type separator resulted in 42 percent recovery of the brine at a treatment rate of 542 gallons of brine per day. Vertical drains proved to be the most promising novel debrining technique investigated. With this method, 45 percent of the brine was recovered in 3 days.

Jan 1, 1977