Search Documents

By W. W. Weller

This report provides low-temperature heat-capacity data and entropies at 298.15° K. for magnesium metavanadate (MgV206) and magnesium pyrovanadate (Mg2V207). The work completes low-temperature measurements planned for alkaline-earth vanadates; an earlier report dealt with calcium vanadates.4 No similar data for these compounds have been published previously. Free energy of formation values at 298.15° K. were derived by combination of the present entropy values with heat of formation data. MATERIALS The materials used in the measurements were portions of the samples described in a previous Bureau of Mines publication by King, Koehler and Adami.5 Methods of preparation, chemical analyses, and X-ray examinations are covered in this paper. The indicated purity of the samples was 99.9 pct.

Jan 1, 1962

By C. H. Elder, Maurice Deul

Coal degasification boreholes drilled from the surface have been success - fully hydraulically stimulated to increase the flow of gas from the coal. This Bureau of Mines report describes the hydraulic stimulation procedure for a coalbed, the equipment required, and design criteria for the treatment. Three examples of stimulation treatment show from fivefold to twentyfold increases in gas production. The tests were conducted in the Pocahontas No. 3coalbed, Buchanan County, Va., the Pittsburgh coalbed, Washington County, Pa., and the Mary Lee coalbed, Jefferson County, Ala. Two sites where the coal was hydraulically stimulated and exposed by subsequent mining show no adverse effect on mining operations through the treated zones. The induced vertical partings were confined to the coalbed and did not in any way affect either roof or floor rock.

Jan 1, 1975

1. In 2001, a total of 785 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Examples of nonmetal mining operations include the mining of clay, trona, barite, phosphate rock, gypsum, talc, gemstones, and pumice. Nonmetal mines comprised 5.4% of all mining operations.1 • Nonmetal mining operations are located in all but seven states or territories (Alaska, Delaware, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands). • The median number of operator employees per nonmetal mine was 6.1.2 • Mines producing common clay comprised 31.2% (n = 245) of all nonmetal mining operations.

Jul 1, 2003

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By E. F. Ferrell

The Bureau of Mines, U.S. Department of the Interior, studied the use of manganese sea nodules for catalytic oxidation in air of 1 pct carbon monoxide, 1 pct propane, and 1 pct methane. Catalysts were prepared from both Pacific Ocean and Atlantic Ocean nodules and compared with a platinum catalyst using a fixed-bed, steady-state microreactor with gas chromatographic analysis. Combustion temperatures with manganese nodules were 50° to 100° C lower than those with the platinum catalyst. Ion-exchange addition of rare-earth promotors to the nodule catalyst decreased combustion temperatures an additional 5° to 45° C.

Jan 1, 1978

By W. W. Weller

Low-temperature heat capacity measurements were conducted, and entropies at 298.15° K were evaluated for sodium monomolybdate (Na2Mo04), magnesium monomolybdate (MgMo04), and calcium monomolybdate (CaMo04). The 298.15° K entropy values were sodium monomolybdate, 38.1±0.3 cal/deg mole, magnesium monomolybdate, 28.4±0.2 cal/deg mole, and calcium monomolybdate, 29.3±0.2 cal/deg mole.

Jan 1, 1963

This study presents a reservoir modeling approach to investigate the relative effects of different coalbed parameters on the migration of methane into development entries. A base coalbed reservoir model of a three-entry development section, where grids were dynamically controlled to simulate the advance of mining at a constant section advance rate, was created and calibrated for a Pittsburgh Coalbed mine in the Southwestern Pennsylvania section of the Northern Appalachian Basin. The values of coalbed parameters were varied to evaluate their effects on predicted methane emissions for various development distances. The results of these parametric simulations were then used to derive linear expressions relating these parameters to methane emissions into the workings. These models were analyzed to assess their significance and adequacy for predictive purposes. This work shows that coupling reservoir simulations with linear modeling yield a technique that can be applicable to different coalbeds. The reservoir parameters used by the linear models (coalbed thickness, pressure, sorption time constant, Langmuir parameters, permeability) can be determined by running relatively simple laboratory tests, such as adsorption equilibrium and permeability determination, on coal samples obtained either from the mining operation or from the exploratory boreholes drilled ahead of mining.

Jan 1, 2008

By Ivette E. Torres

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not exclusively devoted to mineral commodity transport. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to nonmineral goods, as well as carrying mixed mineral commodities and nonmineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-offships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1994

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By P. R. Bremner

In keeping with its mission to maximize mineral and metal recovery from domestic sources, the Bureau of Mines investigated a method to extract silver from tailings not amenable to cyanidation. Results of a laboratory study on the recovery of silver from cyanide tailings containing 1.7 ounces of silver per ton by leaching with an acidic ferrous chloride-sodium chloride solution are presented. The effects of reagent concentration and reaction time on the leaching of silver were investigated. A leaching solution containing 5 wt-pct NaCI, 2.5 wt-pct FeCI2, and 1.2 wt-pct HCI (for acidity) extracted 82 pct of the silver from the tailings during a 24-hour leach. The amount of HCI consumed during the leach was 46 pounds of HCI per ton of feed. Only 23 pct of the silver was extracted by conventional cyanidation. Ninety-nine percent of the silver was recovered from the pregnant solution by cementation onto iron powder.

Jan 1, 1982

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

By D. J. Bauer

Liquid-liquid extraction techniques were investigated by the Federal Bureau of Mines for the fractionation of rare-earth solutions. Separatory funnel work using tri-n-butyl phosphate (TBP) for extracting ceric nitrate from solutions containing sulfate ion resulted in almost complete extraction. Similar tests using primary amines for splitting trivalent rare-earth pairs and fractions gave promising results. The ceric nitrate extraction procedure was scaled-up by use of pressure-bubbler equipment, a series of spray towers for extraction, washing, and stripping. In this case only 84 percent ceric nitrate extraction efficiency was achieved. This work was done using dilute sulfuric acid for stripping.

Jan 1, 1960

By S. E. Khalafalla

The extremely sluggish oxidation of steel scrap was appreciably accelerated when the charge was pretreated in aqueous solutions of sodium metavanadate or sodium molybdate. The degree of oxidation acceleration was inversely correlated with the melting point of the promoter oxide possessing the highest valency. The magnitude of oxidation enhancement exhibited a systematic inverse dependence on the duration of pickling processes; mere dipping of the oxidizable charge in the vanadate bath was most effective. In general, the rate of steel scrap oxidation increased with increasing concentration of the pickling reagent. The results are explained on the basis of the hydrolytic decomposition of the pickling agent with subsequent slow interaction with the metal surface, coupled with the tendency of vanadium to form polyanions in alkaline media. The data not only served to elucidate the mechanism by which catastrophic oxidation takes place, but also showed that the accelerating species need not be alloyed with the oxidizable metal; surface impregnation by minute amounts of the accelerating species can still produce catastrophic effects.

Jan 1, 1970

By R. P. Beyer

[The Bureau of Mines has measured the low-temperature heat capacities and high-temperature enthalpies of crystalline K2Si2O5 as part of a program for advancing mineral resources technology with energy economy. High-temperature enthalpies of glassy and liquid K2Si2O5 and crystalline K2SiO3 were also mea¬sured. An adiabatic calorimeter operating over the range 5 to 308 K was used for the heat capacity measurements for K2Si2O5 from which the standard entropy at 298.15 K, S°298 = 45.55 ±0.05 cal/deg-mole, was calculated. Tabulated values of Cp°, S°, -(G° -HO°)/T, and H°-HO° from 5 to 300 K are given for K2Si2O5. A copper-block drop calorimeter was used in the enthalpy measurements, operating from 298.15 to 1,198 K for K2SiO3 and from 298.15 to 1,453.8 K for K2Si2O5. No transitions were found for K2SiO3. The KI2Si2O5 showed two reversible first order transitions, one at 510 K with a heat of transition of 0.29 kcal/mole and one at 867 K with a heat of transition of 0.38 kcal/mole. The heat of fusion for K2Si2O5 20 5 was calculated to be 8.42 kcal/mole. Relative enthalpies are given in equation form, and high-temperature values are tabulated for Cp°, S°, - (G°-H°298 )/T, and H°-H°298 . Also tabulated are ?H°, ?G°, and log K for formation of K2SiO3 and K2Si2O5 from both the elements and the oxides.]

Jan 1, 1979

By David E. Siskind

The Bureau of Mines performed a comparative study of nine sites at eight surface coal mines to determine if the presence of near-surface underground abandoned workings resulted in the generation of adverse long-duration, low-frequency blast vibrations. Six of the nine sites had underlying workings, and two had thick layers of low-velocity unconsolidated surface material. Extended seismic arrays were used to identify the vibration characteristics within a few tens of feet of the blasts and also as modified by the propagating media at distances over 1 mile. Production blasts and specially fired single-charge blasts allowed the determination of natural ground frequency and the influence of initiation delay timing. Vibration amplitudes from the production blasts at all sites exceeded historical norms, particularly at the greater distances. This contrasts with the near-normal results from single-charge blasts. Apparently, between-hole time delays were insufficient to separate vibrations from adjacent charges for the low-frequency waves present. Single-charge tests showed that the propagating media produced low-frequency, ground-roIl-type surface waves at nearly all sites. Large blasts at such sites could produce an unacceptable risk of vibration-induced cracks in nearby structures.

Jan 1, 1989

By Doris M. Hyde

To a greater or lesser extent, the economies of the smaller Caribbean Island countries continued to have common problems. These included unemployment, inflation, foreign exchange shortages, trade deficits, and unstable world prices for their exports. Declining prices for petroleum provided some relief from scarce foreign exchange. Overall, the mineral sector remained stable. The Amerada Hess Corp. crude oil transshipment terminal on St. Lucia was completed during 1981. However, there were no shipments during the year. No official reason was offered for the delay in opening the terminal, but it may have been related to the world surplus of crude oil that occurred in 1981. There has been no further action on the refinery, which was to complete the island's petroleum complex. During the first half of 1981, an announcement was made that a second oil transshipment terminal would be built on St. Lucia. The report indicated that the terminal was to be financed by Saudi Arabia and include underground storage. After the original announcement, no further information was made available. This terminal, like the Hess petroleum complex, may have been temporarily postponed because of the crude oil surplus.

Jan 1, 1983

By L. E. Geyer

"The following list gives the title and author of various publications of the Ceramic Experiment Station, Columbus. Ohio, of the Bureau of mines, together with other ceramic publications of the bureau, which have been published in technical journals and by cooperating agencies. The list also includes the publications on ceramics which have been issued as bulletins, technical papers, or mimeograph Report of Investigations of the bureau.Papers Published in the Technical Press.The Effect of some Electrolytes on the Properties of Clays. Schurecht, H.G. Jour. Am. Cer. Soc., Vol. 1, #3, March, 1918.A Pycnometer Operated as a Volumeter. Schurecht, H.G. Jour. Am. Cer. Soc.,Vol. 1, #8, August, 1918.The Properties of some Ohio and Pennsylvania Stoneware Clays. Schurecht,H.G. Jour. Am. Cer. Soc., Vol. 1, #4, April, 1918.The Fusibility of Graphite Ash and its Influence on the Refractoriness of Bond Clay. Booze, M.C. Jour. Am. Cer. Soc., Vol. 2, #1. Jan., 1919.Behavior under Brass Foundry practice of Crucibles containing Ceylon, Canadian and Alabama Graphites. Stull, R.T. Jour. Am. Cer. Soc., Vol. 2, #3. March, 1919."

Oct 1, 1924

By Richard G. Sandberg

Sphalerite concentrates prepared during processing of Missouri lead ores contain small percentages of cobalt and nickel which adversely affect zinc electrolysis. The Bureau of Mines has evaluated solvent extraction and precipitation techniques to remove and recover cobalt and nickel from zinc sulfate solution prior to zinc electrolysis. Prepared zinc sulfate solutions containing about 190 gpl of zinc and 50 ppm of both cobalt and nickel were treated using various combinations of complexing reagents, solvent, pH, concentration, time, and temperature. The following complexing reagents gave the best results: a-nitroso-ß-naphthol, ß-nitroso-a-naphthol, 1,2 cyclohexane dione dioxime (nioxime), di-2-pyridyl ketone oxime, and dimethylglyoxime. These reagents in suitable solvents lowered the cobalt and nickel levels to <0.1 ppm. Stripping the complexed reagents from the solvents was not possible except for nioxime. Direct addition of the appropriate reagent to the prepared zinc sulfate solution resulted in the precipitation of cobalt and nickel. Several possible flowsheets are presented for the removal and recovery of cobalt and nickel. Good zinc deposits were successfully electrowon from zinc sulfate solutions purified by solvent extraction and precipitation.

Jan 1, 1978

By R. C. Corey

Anticipating the need for convenient, economical, and safe means for disposing of combustible wastes contaminated with low-level activity, in connection with private and institutional uses of radioisotopes, the Atomic Energy Commission (AEC) has provided the Bureau of Mines with funds to develop an incinerator for this purpose. A prototype incinerator, designated hereafter as BOMAEC-30, was designed, constructed, and tested, based on fundamental and applied research investigations of the combustion characteristics of rubbish and sawdust, which will comprise the bulk of contaminated wastes. No radioisotopes were used in the tests; the objective was to remove as much particulate matter from the products of combustion as possible. The prototype unit was designed to burn 30 pounds per hour, using 100 percent over fire air admitted tangentially in an all-metal, cylindrical combustion chamber. The gas-cleaning system consisted of special fabric bags and absolute filters.

Jan 1, 1962

By James W. Vogh

The report covers initial findings in an experimental program to identify diesel exhaust odorants and determine their contributions to diesel odor. The approach was to isolate selected component groups from exhaust and to evaluate the contribution of each group to exhaust odor. Results were obtained for those carbonyls and phenols that could be isolated from exhaust through inter-mediate conversion to oxime derivatives. Unsaturated aliphatic aldehydes and sterically hindered carbonyls were not included. Hydrocarbons intermediate in the diesel range were "also evaluated and an odor contribution was found from those of the aromatic group. The evaluated carbonyls, phenols, and hydrocarbons were found to account for about 20 pct of the total odor in exhaust from an indirect-injection engine during idle. For exhaust from the indirect-injection engine operating under load and from a direct-injection engine at no load, these compounds were found to have no significant levels of odor.

Jan 1, 1972