Search Documents

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

By W. E. Lamont

The Bureau of Mines studied the potential for recovering marketable barite concentrates that meet oil well drilling-mud specifications from barite waste pond materials. The study was conducted as part of the Bureau's research program to conserve domestic mineral resources by advancing mineral recycling technology. The samples, which were obtained from Georgia, Nevada, Missouri, and Illinois, varied widely in character, particle size, and barite content. The samples were treated with sodium silicate and sodium cetyl-stearyl sulfate and then floated. The flotation flow sheet was modified to reject barren coarse and/or slime fractions from some of the samples, and one feed sample had to be scrubbed prior to flotation to remove residual flotation reagents. The cleaned concentrates had BaS04 contents ranging from 95.0 to 96.9 percent, while recovering 81.2 to 95.9 percent of the barite in the feed. The specific gravity of each concentrate exceeded the specification of 4.2. The removal of the flotation reagents from the flotation concentrate was not investigated.

Jan 1, 1982

By Roy L. Wilfong

Surface area measurements were conducted on cadmium sulfide powders following thermal treatments at temperatures up to 500° C and treatment times up to 1 week. Thermal treatments at temperatures up to 300° C produced no significant changes in the surface area of the powders even after 1 week of exposure. At 500° C some decomposition of the cadmium sulfide occurred.

Jan 1, 1970

By W. W. Weller

Heat-capacity measurements of sodium dimolybdate (Na2Mo207) and sodium ditungstate (Na2W207) were conducted over the temperature range from 51° to 298° K. The entropies of the two compounds at 298.15° K were calculated from the heat-capacity values and were used, in conjunction with other entropy data, to evaluate the entropies of formation of the compounds from their constituent elements and oxides.

Jan 1, 1963

By Chas F. Jackson

 The annual reports of the supervising engineers of the several sections of the Mining Division are assembled herein and comprise the annual report of the division. During the year under review the work was oriented entirely to the war program by applying apparatus and technique previously developed in research directly to war problems, as well as by intensified search for and exploration of deposits of minerals necessary in the war.

Oct 1, 1942

By Pablo Velasco

The Ecuadorean mineral sector and overall economy have retained their traditional dependence upon the production and export of hydrocarbon products. Exports of crude oil and its products accounted for 62% of the country's export earnings in 1985. Ecuador's major mineral commodities produced and exported were cement, gold, limestone, liquefied natural gas, liquefied petroleum gas, natural gas, natural gasoline, crude petroleum and condensate, raw steel, semimanufactured steel products, and sulfur.

Jan 1, 1987

Design a high-production coal mining machine with inherent low dust generation and low frictional ignition potential. Approach Constant depth linear cutting (CDLC) provides a longterm solution to excessive dust generation from shearers and continuous mining machines through new design of the rotary drum culling system. Problems with rotary drum systems, which must be eliminated to control the dust generation at the source, include the effect of a con¬stantly varying depth of cut using fixed bit spacing, secondary fragmentation of already broken coal and, frictional heating of bits and entrainment of dust by fanning action due to high drum rotational speed, Each bit on a rotary drum enters the coal face at zero depth of cut, goes to some maximum depth at the horizontal centerline during sump, and exits at zero depth.

Jan 1, 1989

Provide an environmentally compatible means of producing lead from galena concentrates that replaces the current high-temperature pyrometallurgical primary lead smelting process and supplies pure lead metal within present and proposed Environmental Protection Agency (FPA) and Occupational Safety and Health Administration (OSHA) lead emission standards. Approach The U.S. Bureau of Mines developed an energy efficient and pollution-free leach-electrowinning method for use in recovering pure lead metal and byproducts from lead sulfide concentrates.

Jan 1, 1989

By H. C. Ko

The Bureau of Mines maintains an active program in thermochemistry to provide thermodynamic data for the advancement of mineral science and technology. As part of this effort, the standard enthalpy of formation at 298.15 K, ?Hf°, for 2CdO-CdSO4 was determined by HCI acid solution calorimetry to be -345.69 ±0.61 kcal/mol.

Jan 1, 1983

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

By L. C. George

The Bureau of Mines measured the vapor pressures of selected mixtures in the binary systems CdCl2 ?SnCl2, CdCl2 -ZnC12, PbCl2 ?SnCl2, and PbCl2 -ZnCl2 by the static pressure method. These data were evaluated by the second-law (sigma-plot) method. Equations expressing the vapor pressures and the heats and free energies of vaporization as functions of temperature are given.

Jan 1, 1969

By Dean E. Bluman

The Bureau of Mines investigated the convective heat transfer coefficients for recirculated suspensions of 30-micron glass beads in inert gas. Coefficients for the suspensions were not significantly higher than coefficients for the pure gas. Reynolds numbers of the suspensions were 20,000 to 35,000; solids loadings ranged from 0.0 to 0.7 pound per pound of gas. Comparison of the results with published data showed the direction of heat flow to have no effect at the test conditions.

Jan 1, 1967

By Neil B. Young

Analytical results for nahcolite, dawsonite, total extractable alumina, and oil yield are presented for samples representing Green River Formation oil shales in the saline section of two cores from Colorado's Piceance Creek basin. Analyses are also reported for samples extending the analyzed section of Colorado corehole No. 3 beyond that reported previously. These data permit evaluation of the deposit for possible production of three coproducts--shale oil, alumina, and sodium carbonates--from the saline section of the formation at these sampled points.

Jan 1, 1970

By J. W. Eckerd

Metal production rates of 42 to 45 tons per day were obtained with hollow-core anthracite briquets in an experimental blast furnace. Tuyere pressures were about the same for both coke and briquet operations, but from 150 to 175 pounds more of briquets were required per ton of metal than were needed with coke. Furnace operations were comparatively smooth, furnace hanging occurring less often than in previous tests with anthracite briquets. Dust production was substantially higher than with coke, however, and metal quality could not be controlled by corrective burdening and moisture control.

Jan 1, 1968

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980

Develop a portable emissions measurement apparatus to sample and measure tailpipe concentrations of diesel particulate matter (DPM), carbon monoxide (CO), carbon dioxide (CO2), nitric oxide (NO), and nitrogen dioxide (NO2) under steady-state engine load and speed conditions during a 1-minute test.

Jan 1, 1994

By Michael D. Fenton

The modest mineral industry of Afghanistan continued to suffer adversely from internal disorders that were essentially the result of the continued presence of elements of the armed forces of the U.S.S.R. Despite press reports near yearend intimating that the Soviets might reduce troop strength in Afghanistan, there were no indications of any significant numeric reductions. Indeed, there were clear demonstrations of heightened military actions along the Afghani-Pakistani border, including bombing raids on settlement sites for Afghanis within the territorial limits of Pakistan, actions hardly demonstrative of conditions indicative of Soviet withdrawal.

Jan 1, 1988

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By Van H. Manning

EXPLOSIVES RESEARCH. As the physical laboratories of the explosives section of the Pitts- burgh experiment station were equipped for testing the physical properties of explosives, both the Army and Navy Departments for many years had requested the Bureau of Mines to make such tests. Chemical control of the physical tests through analyses, heat tests, analyses of gaseous products of combustion, and sand tests was exer- cised through the explosives chemical laboratory. Often an investigation was cooperative between two laboratories. The explosives chemical laboratory also aided the work of the Ex- plosives Regulation both by chemical tests and investigation of acci- dents in explosives plants. COOPERATIVE WORK FOR ARMY AND NAVY DEPARTMENTS. The explosives chemical laboratory devised, at the request of the Bureau of Ordnance of the Navy, a more economical method of making hexanitrodiphenylamine. This problem was assigned to the Bureau of Mines by Dr. C. E. Munroe, chairman of the committee on explosives of the National Research Council, acting as the depart- ment of science and research of the Council of National Defense. Before the United States entered the war the following reports of investigations were submitted to the Army or the Navy: 1. Report of sensitiveness and relative efficiency of TNT and ammonium picrate, dated February 6, 1913, undertaken at the re- quest of the Chief of Ordnance. 2. Report of tests and examination of two samples of TNT and one of TNA for the Ordnance Department of the Army, dated August 5, 1915, was undertaken at the request of commanding officer, Frankford Arsenal. 3. Report of tests for sensitiveness to detonation of mercury ful- minate of 21 samples of TNT crystallized from various solvents, for the Bureau of Ordnance, Navy Department, dated June 17, 1916. 4. Report of tests of two samples of mercury fulminate for Frank- ford Arsenal, dated December 2, 1916, undertaken at the request of the commanding officer, Frankford Arsenal. After the United States entered the war the following reports of investigations were submitted: 5. Report of pendulum friction and large impact tests on two samples of "sodatol" and two samples of "amatol." The final report was dated July 20, 1918; and the preliminary report, May 15, 1918. This investigation was undertaken at the request of the Ordnance

Jan 1, 1919

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969