Search Documents

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau of Mines, which conducts research on many of the complicated and frequently interrelated problems of extracting crude oil and natural gas from the ground, transporting them to market or to places for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because may of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941

This report summarizes the results of the Narragansett Win Projec't's activities during the U.S. Bureau of Mines (BOM) Phase 1, which was transitional from and which followed the National Science Foundation (NSF) Phase which initiated the investigation of New England's potential roil resource. The 960 sq. mile basin is structural and topographic lowland containing 12,000 to 20,000 ft. of terrigenous clastic sediments of late Pennsylvanian age, and which rests on an upper Precambrian and Cambrian basement. The Rhode Island Formation, which is the coal-bearing unit, comprising the bulk of the Pennsylvanian rocks consists, in order of decreasing abundance, of sandstone, conglomerate, silts tone, shale, and coal. In the NSF Phase, 24 drill-holes yielded 17,900 ft, of core; in the BOM Phase I study, 4 drillholes yielded 2,100 ft. of core. Anthracite and semi-anthracite was encountered in beds Up to 30 ft. thick in widely spaced parts of the Basin. The coal, typically very low in sulfur, and a high ash anthracite, won mined in substantial volumes from 1808 to 1959 from shaft and open lit in Portsmouth and Cranston, R.I., and in lesser volumes in Mansfield, Mass. Currently coal is now being mined in Plainville, Mass. as a fuel in the manufacturing of light-weight aggregate from the same quarry that serves as the source of the rock being processed. The structurally complex Narragansett Basin is now known to have a greater extent than earlier since recent drilling by others (Chapter 2) has confirmed our interpretation that the Basin extended offshore south A Boston. The, Basin also extends into Rhode Island Sound to the south. The geological structure is more complex in the southern part of the Basin than in the northern part. Three episodes of folding have been documented on Aquidneck Island and four episodes of faulting have been demonstrated for the Basin as a whole. Relatively less well exposed rock in the northern part of the Basin, increases the difficulty of recognizing and correlating structural episodes in the northern part of the Basin. The Basin his hewn subdivided into six structural domains which appear to have distinctive structural, metamorphic, paleontological and sedimentological differences that mw assist in isolating important events in the evolution of the Basin and its component parts. The tentative structural model recently developed in POP Phase I has important implications for exploration and mining. In the first and second folding stages the coal is mobilized and thickened in the crests and troughs of folds whose axes are horizontal to subhorizontal. While conventional coal exploration and mining methods are not applicable, great thickening in the crests and troughs of large scale structures, which can he defined by geology, geophysics and drilling, may provide compensating advantages. Bedrock over most of the Basin is 0-50 ft., but thicknesses of glacial deposits up to 150 ft. are present locally. Pro-Pleistocene topographic trends are controlled by structure and rock hardness; Pleistocene deposits aligned to the S. F. are superimposed on earlier trends. The southern part of the Basin is mainly dominated by high grade Barrovian metamorphism and plutonism of Permian age, related to the Alleghanian Orogeny. About 300 sq. miles of the 960 sq. mile Basin has been affected. The remaining 660 sq. miles, in the chlorite and subchlorite zones of metamorphism are compatible with the presence of high quality anthracite and semi-anthracite. Illite crystallinity studies begun in the NSF Phase, have been carried out in the BOM Phase l with important results. About ME of the northern Basin is now known to be in the diagenetic (unmetamorphosed) or subchlorite zone and the remainder in the chlorite zone of metamorphism. Mite studies, probably best recording temperature effects, show a generally progressive increase from the NW corner of the Basin near Plainville, Mass. toward the south and southeast. Reflectivity and coal petrography studies, probably best recording pressure and effects related to shearing, indicate a generally opposite pattern. Thus these methods provide powerful tools for the ultimate solution of problems important to coal exploration for coals of higher combustible volatile content and exploitation of these. Due to the complex nature of the coal, chemical data may not he easily used to determine rank. The coals have been tectonically deformed and mineralized. This deformation plus thermal metamorphism have altered the coals, in some cases by producing natural coke. Brecciated coal is often coated with a secondary depositional carbon. The coals' hydroscopic nature and high ash contents are due to the deformed nature of the coal and the presence of this secondary carbon. The stratigraphy and sedimentology of the coal-bearing Rhode Island Formation is similar to described alluvial fan deposits. The non-geological studies al-low three conclusions to be made: 1. A substantial number of areas have been identified in the Narragansett Basin in which mining could be carried out without undue difficulty from a land use point of view. 2. Substantially more than two hundred instances of past or current- mining activities have been identified in the Basin. Many of those are in areas defined as geologically interesting, and may be advantageous From the point of view of future exploration. 3. The map synthesis technique developed for this contract is successful and may easily be adapted to future exploration in its current form and also in its expandable form dealing with unit measurements of one-tenth mile. We recommend that BOM Phase 2 exploration should accomplish the intent of the Congressional language in House Report No. 95-1251, to continue a substantial drilling and geophysics program: "The Committee expects the Bureau to continue studies involved in ascertaining the extent and quality of low sulfur coal reserves in the Narragansett Basin in New England including necessary drilling and geophysical studies. The knowledge of the extent of such deposits is of great importance to this 'energy pour' area".

Jan 1, 1979

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office- workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections:

Jan 1, 1963

By John G. Parker

Important quantities of gold, silver, platinum-group metals, selenium, tellurium, and arsenic are recovered in the processing of copper concentrates. The objective of this Bureau of Mines study was to determine the occurrence of these elements in copper ores and to trace their distribution during subsequent processing steps. The study describes the important areas supplying concentrates, precipitates, and unrefined copper to the copper smelting and refining industry in a composite of the years 1971-74. The relative importance of these areas as a source of the respective byproducts is assessed. The lack of certain quantitative and assay data, recycling of dusts and slags, and the addition of scrap to the feed often complicates calculations and estimations of the byproducts in the smelter-refinery throughputs. Such volatile or low-boiling point elements as arsenic, selenium, and tellurium may be lost in gaseous and other emissions in various processing stages, or they may be concentrated in slags and residues for which samples were not available. The effects of antipollution legislation to improve control of sulfurous and other emissions that may affect recovery of certain byproducts was noted. A section on newer technology illustrating hydro-metallurgical techniques that may affect the recovery of minor metals is included.

Jan 1, 1978

By D. D. Southworth

In 1981, 1982, and 1983, the Bureau of Mines examined the potential for lode deposits of platinum-group metals (PGM) in the Goodnews Bay ultramafic complex, Alaska. The complex consists of the Red Mountain, Suzie Mountain, and Smalls River ultramafic bodies and displays concentric zoning of rock types similar to complexes in southeast Alaska, British Columbia, and the Ural Mountains in the U.S.S.R. Results of the study indicate that platinum is preferentially associated with chromite and magnetite in the dunite core of the complex, and palladium is preferentidlly associated with sulfide minerals in the outer clinopyroxene-rich zones. the most promising targets for PGM lode deposits are the chromite-rich dunite at the heads of Fox Gulch and Squirrel Creek and iron-nickel and iron copper sulfide-bearing magnetite clinopyroxenite and hornblende-rich rocks outward of the dunite core, also in the Fox Gulch-Squirrel Creek area. Significant placer reserves are present in the unmined, deeply buried placer ground in the lower Salmon River Valley, and also in tailings from previous dredging.

Jan 1, 2011

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By P. M. Daling

This report, sponsored by the U.S. Bureau of mines, presents the results of an examination of available safety assessment methods and their applicability to the mining industry. Standard safety analysis procedures were evaluated for relevance to the mining industry and mire operators' needs. The major safety concerns and needs of mine operators were identified through telephone contacts and a visit to a mine site. Safety assessment methods recommended for use by the mining Industry were also investigated for potential adaptability to a user-interactive computer system. Several methods were determined to be Immediately transferrable to the mining industry; these techniques are described in a user's handbook produced as part of this project. The handbook gives detailed instructions on appropriate application and utilization of these methods. Other techniques will require further development before they can be effectively transferred to the mining Industry. These methods, their advantages, disadvantages and resource requirements are described in the final project report. Recommended system safety analysis techniques facilitate an evaluation of total mine system safety and a determination of safety-related interactions among systems within a mine. The application of these methods to the mining industry could result In reductions in both the frequency and the consequences of mine accidents.

Jan 1, 1983

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By P. B. Grote

The report is concerned with the issue of the possible transfer of U.S. and other developed country deep ocean mining (DOM) technologies to developing countries. This subject is one of several major issues in current UN Law of the Seas negotiations. As background to the subject, the report provides a detailed critique of the various terms and conditions pertaining to technology transfer in recent negotiating texts. It also provides a description of the relevant DOM technology, sources of innovation, and methods of proprietary protection. Functional requirements for viable technology transfer are developed and used as a basis for the definition of alternative levels of programs and implementation approaches, including required changes in the negotiating text. The consequences of these technology transfer options on the various parties are investigated.

Jan 1, 1978

By Terry R. Neumann

This document, prepared for the U.S. Bureau of Mines Regional Mineral Assessment Program, presents data pertinent to the mineral resource assessment of the Needles 1° x 2° map quadrangle (excluding the Arizona portion), located in the Mojave Desert southeastern California. The U.S. Bureau of Mines (USBM) mineral survey of the quadrangle, conducted from 1991 to 1993, was done to provide the minerals data necessary to support effective land use planning and resource decision making. To this end, this report (1) inventories historic and current mining activity, (2) inventories identified resources, (3) provides an economic analysis; of identified mineral resources and estimates their feasibility for development, (4) delineates areas of exploration and development potential based on current geological, geochemical, and geophysical information, (5) supplies information on land status, transportation networks, power supplies, water availability, and regulations, and (6) analyzes socio-economic impacts of potential mining. The Needles quadrangle is in the Basin and Range province of the southwestern United Van. The area is underlain by a lithologically and structurally complex Proterozoic crystalline basement of gneiss and granite that is overlain by sparse, scattered outcrops of deformed and metamorphosed Late Proterozoic and Paleozoic sedimentary sequences. Mesozoic granitic plutons, particularly in the western half of the quadrangle, intruded the basement and sedimentary rocks, resulting in metamorphism and deformation responsible for the formation of high-grade gneisses and mylonitic rocks (core complex) in the eastern part of the quadrangle. Voluminous Tertiary volcanism unconformably overlie some older sequences. The structure of the area is dominated by Basin and Range extensional block faulting; in the eastern part of the area, block faulting is accompanied by widespread low-angle detachment faulting associated with core complex development.

Jan 1, 1993

By Terry J. Close

From 1981-84, Bureau of Mines personnel examined and evaluated mines and prospects in the highly mineralized 62,400 acre Inyo Mountains U. S. Bureau of Land Management (BLM) Wilderness Study Area (WSA), located east of Lone Pine, CA. The 62,400 acres studied is the part of the 87,145 acre WSA designated as suitable prior to February 28, 1983. The WSA is underlain principally by quartz monzonite and quartz diorite that have intruded sedimentary and volcanic rocks. Three types of mineral deposits are present: 1) gold in fissure veins, 2) silver in fissure and replacement veins, and 3) talc in metasomatic lenses. Of the 84 nines, mills, and prospects examined, 54 are significant: 1) 5 in the intrusive rocks total about 4.4 million tons of inferred marginal gold reserves averaging 0.24 oz gold and 0.74 oz silver/ton; 2) three associated with intrusive-sedimentary rock contact zones total about 280,000 tons of inferred subeconomic silver resources averaging 7 oz silver/ton; 3) 27 gold and silver occurrences in the intrusive and sedimentary rocks total about 1.2 million tons of material in poorly defined bodies too small or low grade to be resources; 4) 15 gold and silver occurrences in the intrusive and sedimentary rocks are too poorly exposed to estimate tonnage and grade; and 5) four talc deposits along intrusive-sedimentary contact zones have inferred marginal reserves totaling about 640,000 tons. The marginal gold reserves at $450/oz might be profitably mined (reserve) at a gold price of about $600/oz and the subeconomic silver resources at a silver price in excess of about $27/oz. The marginal talc reserves might become minable at prices of about $50/ton and $80/ton for unprocessed and processed talc, respectively, after present supply sources are depleted. At most of the 54 significant mines and prospects, additional reserves or resources would likely be disclosed by trenching or drilling. Present in the WSA are 13 gold mills, numerous small pits and cuts, 270 underground workings totaling about 36,000 ft, and 80 mining benches totaling about 11,000 ft. Gold, silver, or talc were produced from most of the workings. A total of 1,561 lode and 18 placer samples were taken.

Jan 1, 1985

By H. Stanley Benson

This report is an account of research conducted to improve the performance of and then further field test Draft Power Sensor (DPS) equipment, the use of which enables a bulldozer operator to optimize his machine's work rate. Significant improvements were made in DPS hardware, and extended field testing was conducted at two working strip mines: the Glenharold Mine of Consolidation Coal Company, near Stanton, North Dakota, and the Beulah Mine of Knife River Coal Company, near Beulah, North Dakota. This report documents the increase of bulldozer work production by greater than twenty percent while using the Draft Power Sensor when compared to baseline work production without benefit of the Draft Power Sensor. Research was done by Southwest Research Institute under contract with the Bureau of Mines.

Jan 1, 1980

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

By Stephen Gerard Sawyer

This report presents a Fortran IV computer program for the structural analysis of space-frame protective canopies used in underground mines to protect equipment operators from falls of roof, face, or rib. This program entitled CANOPY permits rapid calculation of the elastic strength of a canopy for a variety of static loading conditions. Stresses in, and displacements of each structural member are computed and printed out. Additionally, identification of all members that have commenced yielding, weight of the canopy, total loads on the canopy, and maximum loads that the canopy can sustain elastically are output. Program description, input instructions, program listing, and two example problems are included.

Jan 1, 1972