Search Documents

By Joan C. Biordi

In this research by the Bureau of Mines, slightly lean CH4-O2-Ar flames at 0.042 atm with and without small amounts of the inhibitor CF3Br were probed using molecular beam and mass spectrometric techniques. Ratios of product concentrations to reactant concentrations were formed and compared with the equilibrium constant for seven reactions--(l) H+O2 = OH+O, (2) O+H2 = OH+H, (3) OH+H2 = H2O+H, (4) OH+OH = H2O+O, (5) CO+OH = CO2+H, (6) Br+HBr = Br2+H, and (7) H+HBr =H2+Br--to determine to what extent they may be considered balanced in various regions of the flame. With the possible exception of reaction 4, none of the reactions are completely balanced until maximum flame temperature is reached. Once the reactions become equilibrated, their balance is maintained as the temperature and radical concentrations falloff in the secondary reaction zone. Reaction 7, in inhibited flames, is balanced at relatively low temperatures, comparable to reaction 4. Reaction 6 was found not to balance in either the secondary or primary reaction zones. Radical decay in the secondary reaction zone was analyzed using the pool-decay concept. The important recombination reactions were judged to be H+OH+M~H2O+M, and H+O2+M?HO2+M. A rate coefficient of 2x1016 cm6 mole-2 sec-1 is calculated for M = the burnt gas mixture of Ar, HaO, CO2, and 5x1015 cm6 mole-a sec-1 is calculated for M = Ar (both for T = 1,750±150 K).

Jan 1, 1977

By Sidney Katell

An economic analysis of underground gasification of coal, based on experimental results obtained by the Bureau of Mines, indicates that a gas suitable for use in a power plant might be produced for approximately $.62 to $.77 per million British thermal units. This estimate does not include cost of land purchase. The gasification experiments were conducted in a 3-ft. seam of high volatile A bituminous coal. The major factors which can influence a change in operating costs are height of overburden, power costs, thermal efficiency, and the gasification air inlet pressure. The following equations show the relationship of these factors to operating costs:

Jan 1, 1961

By C. H. Elder

A 5-hole pattern was drilled from the surface at a site near Oak Grove, Jefferson County, Ala., to degasify the gassy Mary Lee coal bed in advance of mining. Gas and water production was monitored for 1 year, 4 months to allow gas flow to stabilize fully. A thickened water stimulation treatment was designed and applied in one hole of the pattern to evaluate this degasification technique for the Mary Lee coalbed. A gas production rate of 70,000 fts/day after stimulation treatment indicates that the use of vertical boreholes coupled with hydraulic fracturing in advance of mining the Mary Lee coalbed would provide for more rapid degasification and could provide a possible source of natural gas.

Jan 1, 1974

By R. H. Lien

The Bureau of Mines developed a flue gas desulfurization process as part of its goal of minimizing the undesirable environmental impacts associated with energy and mineral-processing plants. The modified citrate process involves absorption of sulfur dioxide (S02) in a buffered citric acid solution. The S02-loaded solution is regenerated by countercurrent contact with steam in a packed tower. The wet S02 product is then dried and can be liquefied or further processed to make sulfuric acid. Test data from process investigation unit studies are presented. Material balances, flowsheets, and cost estimates are given for recovering S02 from copper smelter reverberatory gas, lead smelter sintering machine tail gas, and power-plant stack gas. Operating cost estimates show the process will add $0.04 per pound of copper, $0.01 per pound of lead, and $0.015 per kwhr to the cost of the respective operations. These costs could be substantially reduced if a source of waste heat was avail-able to provide the process steam requirements.

Jan 1, 1982

By Mohan K. Wali

Soil and vegetation development were studied on abandoned mine sites near Velva in Ward County, North Dakota. The sites studied were 1, 7, 17, 30 and 45 years old since abandonment; unmined sites were also studied to provide measures of comparison. Species diversity was the highest at unmined sites (114) and lowest at the I year old site (26); sites 7, 17,30 and 45 years old had 37, 52, 43 and 68 species, respectively. Stand ordination revealed that site ages were the most important in influencing species diversity and composition. Stand-environ-mental complex ordinations encompassing 53 variables showed topographic variables to be the most important followed by site ages. Rates of nutrient accumulations were as follows: organic carbon 13.1 g m-2 yr-1; nitrogen 2.5 g m-2 yr-1; phosphorus 0.01 g m-2 yr-1; potassium 0.49 g m-2 yr-1. Carbon-nitrogen ratios showed the widest range for 1 year old sites (5-40) but 70 percent of the 45 year old sites showed values below 15 which were com-parable to the unmined mixed grass prairie sites. Species distributional diagrams are provided to show their habitat preferences which may be helpful in formulating species prescriptions for revegetation.

Jan 1, 1982

By F. R. Lee

This publication lists permissible equipment approved by the Bureau of Mines during 1967 and 1968 (calendar years), except breathing apparatus and explosives. The purpose of this publication is to inform the public about approved equipment for use in underground mines.

Jan 1, 1970

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used in this report are divided into two components for individual analysis-- (1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By H. P. Greenwald

[For sarno years past the Safety in Minbr. Resaarch J30ard of Great Bri tr-dn ha:1 been making ar.. intensive Gearch for, traterials that \.'ould be 1!\ore ef-ficient than rock dust and th t 'could l1eplace it Jholly or in El:}rt as a muans of prevEll'ltine the propa 'tion' of 'c63.1~dust exnlosions in. mines21 In the course of this \o.'ork several rock c.ur--ts md numerous inorganic compounds I,/ere tested. The result w place incombus.ti ble substFlnces in two main groups~ (1) r.:ho se who sa effect' in suppre aeina Jlihe cor.lbustion of coal dUDt i 0 pro-]

Jan 1, 1940

By David K. Hylbert

This study investigated stratigraphic and structural causes of roof falls in room-and-pillar drift coal mines in nine mines in eastern Kentucky. A contract modification provided for remote sensing studies in the Dunkard Basin of West Virginia and Pennsylvania. Results of stratigraphic and structural studies of an earlier contract (H0133018) were applied to several new mines. It was found that similar rock sequences contributed to unstable roof conditions. Structure contour and isopach maps were found useful In projecting these trends together with fence diagrams. Using Landsat imagery, a direct relationship was found between lineament direction and the trends of rock jointing, roof fall zones, "snap top" zones and sandstone channels in the examples cited. It was found that, by analyzing lineament intersections, from 50 percent to 65 percent coincided with roof falls.

Jan 1, 1980

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

By Kenneth C. Stewart

The overall purpose of this study was to develop and evaluate, in the laboratory, instrumentation and procedures which might allow for the use of physical measurements of earmuff attenuation which would yield results equivalent to those obtained from psychophysical measures of attenuation. The ultimate goal was to evaluate techniques which might subsequently prove feasible for physical measurement of earmuff attenuation in the field. Current instruments were modified to have a response similar to differrences observed in earmuff attenuation as observed in Volume 1 of the current contract. Mining noise spectra were selected and presented to a single subject seated in a diffuse noise field. The subject wore one of the muffs evaluated in the earlier study and was also fitted with two physical sound measurement systems. A linear system measured the "outside" noise level and a linear system plus "correction" filter measured the "in-side" noise level. These measurements indicated that, under the procedures presented in this report, a laboratory method for measuring earmuff attenuation is feasible and yields results comparable to an extensive psycho-physical procedure.

Jan 1, 1980

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By John D. Bardill

Data from extensive tests was obtained on friction-head losses of various sand slurries, composed of materials of different specific gravities and under varying transport conditions, to provide useful information for designing hydraulic transport systems. The tests were run in a pilot plant through 2-, 3-, and 4-inch lines with slurries composed of relatively pure barite and limestone solids. Available grinding and classification equipment did not permit attaining a comparable size distribution in the two materials tested, thus preventing direct correlation of friction-head loss values to physical properties or mineral composition. A total of 495 measurements were made of limestone slurries in the 2-, 3-, and 4-inch pipe test sections at flow velocities from 6 to 14 feet per second and pulp densities from 40 to 70 percent solids. A total of 640 measurements of barite slurries were made in the 3-and 4-inch pipe test sections at flow velocities between 7 and 14 f.p.s. and pulp densities ranging from 40 to 80 percent solids.

Jan 1, 1962

By G. S. Beaumont

This report presents a programme of work to demonstrate the use of a surface-based centralised computer control system for the remote monitoring and control of underground conveyors in a US coal mine. The system selected for demonstration was the 'Dynalink' Micro MINOS system which is manufactured by Hawker Siddeley Dynamics Engineering Limited. The site selected was Barnes S Tucker Lancashire No. 20 Mine located near Carrolltown, Cambria County, Pennsylvania. The system concept, operating and application software was designed and developed by the. British National Coal Board. The report describes the selection of the site, specification of the system requirements, commissioning, operation and evaluation of the system under typical US mine operating conditions. Experience with the system, based primarily on the system reliability and performance of conveyor control, was favourable. Mine management personnel felt that the system had successfully achieved its objectives and were keen to expand monitoring and control to other activities.

Jan 1, 1986

By Alton B. Cook

In the Scurry Reef field, Scurry County, Tex., a study was made to determine the physical properties of the oil in all parts of the reservoir by a new method developed for this study. The method involved correlation of data from a survey 1 of the gravity of the produced oil, from measurements of gas-oil ratios on key wells selected to give representative data for the entire reservoir, and from laboratory analyses of reservoir oil samples. A field survey was made of the API gravities of the produced oil by testing oil samples from 107 key wells. Precise gas-oil-ratio tests were made on 45 key wells that were producing under comparable separator-operating conditions. Subsurface-oil samples were obtained from seven wells, selected to provide reservoir oils ranging approximately from a minimum to a maximum in saturation pressure. The physical properties of the subsurface-oil samples were determined, and correlations were made of these laboratory data with the field gas-oil-ratio test data. These correlations were then used to estimate physical properties of the oil throughout the reservoir. A logical procedure of determining the variations in physical properties of reservoir oils in most fields is to obtain and analyze subsurface-oil samples from enough key wells to provide an ample coverage of the field. Under this procedure, data from a large number of samples would be needed to provide the desired information on the Scurry Reef field, as it is one of the largest known in the United States.

Jan 1, 1955

By R. T. Johansen

A gradual decrease in injection rates commonly occurs as a water-flooding project becomes older. This decrease can be attributed to changes in reservoir conditions, such as swelling of clay minerals, fillup, or gradual plugging of the sand face. However, a rapid decrease in the rate of injection indicates abnormal behavior and is cause for alarm. Extreme plugging conditions can completely stop injections into a formation. Such behavior in wells was the main concern of the tests described in this report. An accepted method of alleviating this condition is by backflowing input wells - closing the supply lines to the wells and allowing the reservoir pressure to force water back into the wellbore and to the surface. If backflowing is not successful, a string of smaller diameter pipe sometimes is run inside the casing, and the sand face is flushed with a waterspray. More drastic treatment is to inject acid into the wellbore to dissolve extraneous matter, or even part of the reservoir material, in an attempt to restore the permeability of the sand immediately around the wellbore. Any of these procedures can he coordinated with bailing and swabbing of the well for cleanout purposes.

Jan 1, 1957

Mining men and State officials in their efforts to make mining safer are confronted from time to time with various complicated questions. In recent gears these questions have tended to increase with the use of mechanical appliances. Twenty-five years ago electricity had been used but little in mires; today there is practically no other means of transmitting power employed in American mines, except that in metal mines compressed air is used, chiefly for drilling and for operating small portable hoists. In coal mines there has been a great increase in mechanization, which tends to concentrate the work of production in small areas and to increase the local difficulties of ventilation; also, it has intensified locally the hazard from coal dust as well as firedamp in bituminous and subbituminous mines. The answers to the questions that arise are not always obvious, as is shown by the fact that even able, experienced men differ in their opinions of the best, way to overcome a particular mining hazard. The difficulty of .solving the problems is also demonstrated by the varying provisions in mine-safety rules, both in official regulations and in the rules of those mining companies that are endeavoring to do more than follow the letter of the law. Such differences of opinion as to the best way of meeting a difficult situation are often found within the same mining organization, and, similarly, varying opinions are held by different members of the Bureau of Mines staff.

Jan 1, 1937

By D. Bienstock

The use of alkalized alumina in removing sulfur dioxide from a coal-combustion flue gas at 625° F was investigated on a pilot plant scale. The absorber was 26 feet long and 1.6 inches ED. Counter-current gas-solids flow at gas velocities of 8 to 15 ft/sec in the presence and absence of baffles, as well as solids entrainment at gas velocities of 20 to 23 ft/sec with solids recycle, were employed. The spent absorbent as regenerated as fixed bed with the reducing gases--reformed natural .7.7d hydrogen. Of absorption-regeneration were successful completed using the alkalized alumina rolled into spherical granules 10 to 16 mesh. There was no loss in activity of absorbent toward SO2 with a modest attrition equivalent to 0.l percent of the solids feed. Supporting studies were conducted on the effect of the sodium content in the absorbent, the composition of the reducing gas, thermal treatment to increase absorbent hardness, and removal of absorbed chlorine from the absorbent. A mathematical model was formulated to describe the removal of SO2 by alkalized aluminum from fixed and falling beds.

Jan 1, 1967

By W. T. Millar

Field reconnaissance and laboratory tests an clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979