Search Documents

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the Bureau of Mines to aerosol measurements in diesel equipped underground noncoal mines. The first technique is based on size selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately sub-micron in size while the mineral dust fraction of the aerosol is mostly super-micron in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size distribution data were modeled using a log-normal regression to parameterize the sub- and super-micron fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. For the mines visited, analysis of the size selective: samples yielded an average value for the fraction of the fine aerosol attributable.to mineral dust of 3 pct.'The CMB analysis, applied to both fractions of the respirable mine aerosol, yielded the amount contributed to each by the diesel· and dust aerosol sources. Less than 5 pct of the sub-microm fraction was mineral dust, however, as much as 20 pct of the diesel aerosol was found: ""in the super-micron fraction requiring a correction of the sub-micron fraction to account for the missing diesel mass. More accurate measurement will require a carbon specific analysis of the aerosol."

Jan 1, 1988

By Liming Yuan

A study of the ignition of non-fire-resistant hydraulic fluid sprays was conducted by the National Institute for Occupational Safety and Health. Both an open flame and a hot steel surface were used as the external heat sources. With the open flame as the heat source, the minimum oil temperature and minimum spray nozzle pressure that resulted in an ignition were measured. The effects of the distance between the open flame and the nozzle and the nozzle orifice diameter on the ignitability of the hydraulic fluid sprays were examined. With the hot surface as the heat source, the minimum surface ignition temperature was determined. The degree of oil atomization and the relative direction of oil injection with respect to the hot surface are discussed. The ignition of oil sprays from the impingement of oil jets onto a vertical surface was also investigated. Finally, the results are compared with those obtained for fire-resistant hydraulic fluids. Keywords: Ignition; hot surface; open flame; hydraulic fluid

Jan 1, 2006

By M. H. Kline, T. J. Ballard

"INTRODUCTION The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve, elongated to the north, approximately 26 miles in length.The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N. C., to the Hcupscup Knob prospects in Carter County, Tenn.The deposits were worked at least as early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.The magnetite rock is amenable to concentration. Numerous laboratory tests and pilot-mill operations have proved that a high-iron, and low-phosphorus concentrate can be obtained by fine grinding and magnetic, separation, the quality of the concentrate depending upon the extent of grinding. The principal objectives of the Cranberry project were threefold.The primary consideration for beginning exploration of the deposits was the need for developing additional deposits of high-grade iron ore during the war and for replenishing the war's depletion of iron-ore reserves for the peacetime economy. The emergency did not permit logical sequence bf development, and it was necessary to begin drilling before the geophysical survey was completed. The first drilling was begun at the Cranberry mine; and the holes were located from the geological data, coordinated with the position of the mine workings."

May 1, 1948

By Charles J. Cohen, Donald F. Reed

"INTRODUCTION AND ACKNOWLEDGMENTSThis report supplements a previous report on work done in this same area 4/ but covers only the period from November 1945 to November 1946. The project was established in 1943 to investigate magnetite deposits in the northwestern Adirondacks by geophysical surveying and diamond-drilling for the purpose of increasing iron production in the eastern United States.In its program of investigation of mineral deposits, the primary objective of the Bureau of Mines is the more effective utilization of our mineral resources, that they may make the greatest possible contribution to our national security and economy. The policy of the Bureau is to publish the facts developed by each project as soon as possible after its conclusion. Maps showing the detailed magnetic surveys of the deposits and anomalies discussed in this report are on open file at the offices of the Bureau of Mines, College Park, Md., and at the University of the State of New York in the office of the Director of the State Science Service, Educational Building, Albany, N. Y.The Mining Branch, Lowell B. Moon, chief, conducts preliminary exami¬nations, performs the actual investigations, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical analyses included in this report were made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under, the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, in charge of the laboratory service unit."

Nov 1, 1947

By Louis A. Panek

The practice of roof bolting, now recognized as an effective method of support, is based largely on rule of thumb. Among the various applications of bolting, the support of stratified mine roof is by far the most common. The general principles relating to this type of reinforcement are presented in two companion reports; the first describes the function of the bolts, the bolting pattern, and the behavior of bolted roof (1), 2/ and the second describes the design of the models and the theory of the experimental method (2). This report presents a rational method for designing systems of vertical bolts to reinforce horizontally bedded mine roof, developed from model tests. The structure treated herein may be described as follows: The immediate roof, consisting of beds of like material and equal thickness with no bond between them, is reinforced by vertical bolts installed in straight lines across the opening; the case of suspension is excluded because the bolts are assumed not to extend above the immediate roof. The assumption is made that the behavior of the lowest bed approximates that of a rectangular plate clamped along two opposite sides (the ribs). These specifications represent approximately the roof conditions encountered in mining bedded deposits of all kinds - coal, potash, iron ore, etc. Thus, for the design of a roof-bolting system a quantitative solution to the following problem is required: For a roof composed of beds of given thickness and physical properties, how does the support depend upon the length, spacing, and tightness of the bolts?

Jan 1, 1956

By David Schlain

"IntroductionThe purpose of this investigation was to study the characteristics of the high-acid electrolytic manganese cell with the idea of fitting it into one of the flow sheets being worked out by the Metallurgical Division of the Bureau of Mines for the recovery of manganese from low-grade domestic ores.In construction, the high-acid cell 3/ differs from the low-acid type in that the cathode and anode compartments are separated by a diaphragm of relatively low porosity, such as alundum. This is necessary because in the high-acid cell the two electrolytes are circulated separately. The anolyte is 15 to 30 percent H2SO4. The catholyte consists of a solution of ammonium sulfate and manganese sulfate with a OH of 4 to 3. The only mixing of electrolytes is that resulting from flow through the diaphragms. In the low-acid cell the two electrolytes are not circulated separately and do not differ so widely in hydrogen-ion concentration. Hence, the canvas diaphragm is sufficient.During operation of the cell, manganese is deposited on the cathode, and sulfuric acid is produced in the anode compartments. Various other reactions take place in the cell. There is considerable decomposition of water; hydrogen is evolved at the cathode, and oxygen is liberated at the anode. When lead anodes are used, some hydrated oxides of manganese are formed at the anodes. The quantity of oxides formed is not as great as it is in the low-acid cell, because fewer Mn++ reach the vicinity of the anodes."

Jul 1, 1942

By Will H. Coghill

The jig men of the Tri-State (Joplin-Miami) zinc district complain about the flakiness of their mill feed. They believe that the flakiness of the composite grains of gangue and mineral are to blame for losses of zinc; that is, that the flaky grains in the jig tailings have higher zinc tenor than the cubical grains. Although the evidence which follows contradicts this belief, no effort is made to give a final and conclusive answer. On the other hand, there is outlined a positive and mechanical method which the operator may use to pursue this and similar investigations. DISCUSSION OF SCREENING METHOD Hand-sorting is obviously not satisfactory for separating cubical grains from flaky grains because the personal influence can not be removed. Screens, however, may be used with success. A set of each of two types of screens is required; namely, the square-hole type and the rectangular (rectang, oblong) type. The square-hole screens must be of the double Tyler scale; that is, the order of the sieves should be after the fourth root of two instead of the customary square root of two; close sizing is important. The size of the rectang screens may be selected by trials so that a part of the material already closely sized on the square-hole screens, will pass the oblong holes. Obviously, the cubical grains will remain on the rectang and the flaky grains will pass through. Hence the mode of operation is to screen first on square-hole screens and then split the products on the oblong-hole screens.

Jan 1, 1928

By H. L. Riley, B. W. Gandrud

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers, has made a series of washability studies to obtain technically and commercially important data regarding the productive coal beds of the State. Based on the system followed in these studies, this report consists principally of screen-sizing and float-and-sink data on the Clark and Gholson beds at Boothton, Ala. A previous washability study 4/ has been made on the Clark bed at Marvel, Ala.SAMPLING AT MINESThe coal from the Gholson and the Clark beds was sampled at the tipple which receives the output,the Boothten No. 3 and No. 4 mines. These two mines are on the Gholson and Clark beds, respectively, but the coal. from both mines is mixed on the tipple and washed in the same washery. The samples taken were minus 4-inch raw coal. The plus 4-inch raw coal is hand¬picked and not washed. AS the 4-inch screen had a capacity in excess of the output of the mines, it was stopped at the end of each mine-car trip. By Observing from which mine incline each trip was hoisted, a separate sample from each bed was cut from the discharge stream of an endless belt which conveys the through 4-inch raw coal to the bin ahead of the washer. The output from each bed was sampled uniformly over the period of a working shift. The two washability samples weighed approximately 3,000 pounds each."

Dec 1, 1947

By Wilbur I. Duvall, Thomas C. Atchison, David E. Fogelson

The breakage of rock by explosives depends largely on the ability of an explosive to transfer its stored potential energy to the rock as strain en- ergy. Therefore, the relative rock-breaking abilities of explosives can be determined indirectly by determining the relative amounts of strain energy transferred to the rock at the time of detonation. This report presents experimental data on the strain energy contained in explosion-generated strain pulses in a granite gneiss. Six explosives were tested. The scaled total radial strain energy E/W flowing outward through a spherical shell of scaled radius R/W1/3 surrounding the point of detonation was found to follow an exponential decay propagation law of the form Analysis of the data showed that the intercept parameter H depended upon the type of explosive used but that the absorption coefficient B was practi- cally independent of the type of explosive. Comparison of the intercept pa- rameter H and the calculated energy of the explosive showed that the percent- age of explosive energy transferred to the rock increased linearly as the ratio of the characteristic impedance (product of density and propagation velocity) of the explosive to that of the rock increased toward unity. From 5 to 9 percent of the calculated total energy released by the explosive was transferred to the rock as radial strain energy.

Dec 1, 1959

By A. C. Fieldner, G. W. Jones

Tests were made at the Government Fuel Yard , operated at Washington , D. C. by the Bureau of Mines , Department of the Interior , in order to determine and improve the adjustment of the carburetors on the trucks used for transporting coal from the Fuel Yard to the different Government buildings in Washington . The tests were made possible through the hearty cooperation of G , S. Pope , engineer in charge of the Fuel Yard . Joseph Burrows and A. E. Foote of the garage department assisted during all the tests and supplied information on the mileage obtained by the trucks for the months preceding and succeding the time the tests were made . The Mack trucks used range in capacity from 2-1/2 to 7-1/2 ttoonnss .. The majority of the carburetors were Stromberg G- 3 type , as shown in Table 2. During the winter months , when the demand for coal is heavy , from 30 to 35 trucks are used . At the time the tests were made , only about ten of the trucks were in daily use , owing to the small demand for coal during the summer months , and scarcity due to labor conditions . Samples of the exhaust gas were taken on the trucks kept in service for summer hauling in order to determine the carburetor adjustment as used . Changes were then made to a more economical adjustment wherever possible , without sacrificing flexibility of operation and power . In every case the adjustments were maintained for maximum power , but were adjusted to the leanest position to give that power . In all but one case the carburetors were found to be adjusted too rich for maximum power and economy . These results are considered in detail in a later part of this report .

Jun 1, 1923

By G. S. Rice, H. P. Greenwald, H. C. Howarth

"""Rock-dust barriers""5 as they are termed in this country, are for the purpose of confining a coal-dust mine explosion to the limited area in which it originates. These barriers were first tested in 1910-1911, with favorable results under the conditions of test, at the French official gallery which was then at Lieven, Department of Pas-de-Calais. Shortly afterwards the Bureau of Mines in the course of its investigation of all practical explosion-prevention methods tried barriers in the Experimental Mine near Bruceton, using the primary form of simple fixed cross shelves 20 inches wide extending over the passageway and laden with rock-dust. The Bureau termed them “Taffanel barriers"" in honor of the director of the Lieven testing station. The trials were made in conjunction with tests of explosibility of different coal-dusts.Experience showed that although the principle of barriers had merit when they were used for secondary defence, the primary form was uncertain in effectiveness. This led the senior author to design mechanically discharging barriers to be operated by the compression air waves which precede the flame of an explosion. For the better understanding of the principal involved, it is pointed out that the advance air waves are what make a coal-dust explosion possible by stirring up the coal-dust from the walls and floor of the passageway. If a barrier can throw inert dust into the air to form a cloud as dense or denser than that formed by the coal-dust, it will neutralize the explosiveness of the coal-dust, and the flame of the explosion will be extinguished. When the flame ceases, the pressure dies away in a short distance if the 'area that had been traversed by the explosion is not large."

Jan 1, 1930

By H. B. Hill

Virtually from the date of its discovery in December 1928 the Oklahoma City oil and gas field, Oklahoma County, Okla., has attracted national and international attention. The history of the field has been associated closely with rules and regulations pertaining to production control and proration practices. Early development was rapid, and Oklahoma City soon attained the distinction of being the first major field in which the producing wells were over a mile in depth. Before the structural features of the reservoir had been disclosed every outpost well was considered a "wildcat", so complex appeared the underground geology. The wells not only were deep and the reservoir pressures high, but the production from the early wells was a high A.P.I. gravity oil, accompanied by large volumes of gas. Several "blow-outs" and fired occurred during the early development, and the close proximity of these now unusual events to a large city gave the field much publicity, both local and national. Later, when its production threatened to demoralize the market for oil and its products, the Oklahoma. City field again attracted wide publicity. The then little understood geology of the underground reservoir and the diversity of ownership of the land overlying the producing structure made orderly development and production difficult to enforce. Proration was enforced with difficulty, and the rate of production from the field continued to increase until, on August 4, 1931, martial law was declared in all prorated fields of the State, and most of the wells in the Oklahoma City field wore shut in. On October 9, 1931, permission was granted to reopen and produce the wells in the Oklahoma City field. The order permitting production of the wells provided that during the period beginning October 10 and extending to October 20, 1931, all wells in the field that had not produced more oil than specified under the earlier proration orders and that had been shut in for the required 65-day period were permitted to produce 5 percent of their last potential during that 10-day period.

Jan 1, 1936

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

By W. P. Yant, R. R. Sayers, H. W. Shoaf, John Chornyak

"The contemplated use of dichloro-difluoro methane in domestic and commercial refrigerating appliances and in air-conditioning equipment for Public buildings and possibly homes, brings attention to the health hazards involved in a wide potential exposure of the public to vapors of another new product, and for the first time to vapors of an organic fluorine compound. The objective in the development of this new refrigerant, however, has been the mitigation of health and explosion hazards in automatic refrigeration, and accordingly these factors have been given primary attention. Early in the development, the Bureau of Mines was requested to make a laboratory study of the toxicity and potential hazard:"" and it was on the basis of the results of this work and the results of a preliminary investigation made in another laboratory5 that the compound has been selected for commercial use. Although the investigation conducted by the Bureau of Mines is still in progress, information has been obtained to indicate the order of the toxicity and the magnitude of the health hazards involved in the use of dichloro-difluoro methane as a refrigerant. The following is a summarized report of the work completed to date:Additionally work rich is in progress at the present time includes a determination of the lethal time-concentration curve for animals and a study of the response of persons within the range of safe concentrations.The writers desire to jive acknowledgment to T E. Midgley, Frigidaire Corporation, Layton, Ohio, for suggesting the investigation, for arranging for the cooperation of the Frigidaire Corporation, and for advice during the experimental work; to Robert A. Kehoe, The Eichberg Laboratory of Physiology, University of Cincinnati, Cincinnati, Ohio; and E. R. Hayhurst, college of Medicine, Ohio State University, for consultation and advice in planning the work; and to the following employees of the Bureau of Mines for assistance in performing the experimental work: L. M. Berger, chief scientific aid, S. J. Pearce, junior chemist, and Ethel B. Stead, technician."

May 1, 1930

By Albert H. Fay, Herbert M. Wilson

The national mine-safety demonstration at Pittsburgh, Pa., was projected and undertaken in the hope that it would aid the increase of safety in the mining industry. That the national mine-safety demonstration was warranted and has served a useful purpose was evidenced by the attendance, not only at the public demonstration in Forbes Field, but also at the more special exhibit of the work of the Bureau of Mines at the arsenal grounds and at the experimsntal. mine. Nearly 2,000 persons witnessed the demonstrations and exhibits of the Bureau of Mines at the arsenal grounds on the morning of October 30, 1911. The spectators were all mine operators, miners, or persons interested in mining, and represented operations in all parts of the United States. Nearly 1,200 of these persons visited the bureau's experimental mine at Bruceton to witness ~th~explosion of coal dust. Had the weather, which was exceptionally inclement, been more favorable, there would doubtless have been a much larger attendance. At the public demonstration in Forbes Field, which· was witnessed by President Taft, from 12,000 to 15,000 persons, chiefly mining men, were present and attested their interest and enthusiasm in the minesafety exhibits by remaining throughout the proceedings, regardless of the rain which fell all the morning .. Sincethis demonstration, the organization of first-aid corps and of rescue corps has been undertaken at mines where there had previously been no such organizations. The bureau has received letters of commendation attesting the value of the demonstration in drawing· attention to the dangers and to possible means of greater safety in mining. Many of these letters have urged that the results of the demonstration be published for the guidance and instruction of those who were present. In response to these reauests the following account of the mine- BlIIeLY demonstration lias been prepared. IIi its preparation various division and section chiefs of the Bureau of Mines have cooperated. The authors acknowledge the assistance they have received from those section chiefs and other members of the bureau who contributed detailed descriptions of apparatus exhibited at the demonstration or of investigations represented.

Jan 1, 1912

By R. V. Ramani

"In this paper, the current status of respirable dust control in coal mine atmospheres is presented. The advancements in the engineering control of dust generation and entrainment, and of reducing the exposures are summarized. The results of the Health Surveillance Program are briefly reviewed. The results of research conducted in the Generic Mineral Technology Center for Respirable Dust are presented. The 1995 NIOSH criteria document on respirable coal mine dust is briefly reviewed. The fundamental scientific and engineering issues in need of research are discussed. A detailed bibliography is attached.IntroductionFor coal mines in the United States, the current permissible exposure limit (PEL) of 2mg/m3MRE-equivalent concentration (an 8-hour TWA concentration measured gravimetrically) was established by Public Law 91-173: the Federal Coal Mine Health and Safety of 1969 (the 1969 Coal Act). This standard is reduced when the respirable quartz content in the dust sample exceeds 5%; the reduced standard in mglm3 is obtained by dividing 10 by the percent quartz. The OSHA and ACGIB PEL for respirable coal mine dust is also 2 mg/m3 , and OSHA PEL for respirable quartz is 100 µg/m3 . The 1969 Coal Act also prescribed two activities in the Coal Mine Respirable Dust Sampling Program and the National Coal Workers' Health Surveillance Program n to control respirable dust in mines, and the coal worker's pneumoconiosis (CWP) among the coal miners.There are three principal methods by which personal exposures to respirable dust are controlled. The first is engineering control where the aim is to reduce the concentration in the mine atmosphere to or below the mandated level. The second is the provision of personal protective devices which allow the miner to work in dusty atmospheres without increasing personal exposure. The third is the use of administrative controls where the miner's exposure is controlled through work schedules and procedures to keep miner exposure at or under the mandated levels. The 1969 Coal Act specifically prohibits the use of respirators in lieu of environmental control. The compliance sampling program essentially does not give any credit to the use of administrative controls."

Jan 1, 1998

By J. M. Mutmansky, R. A. Jankowski, M. A. K. Mohamed

"SYNOPSISKnown health hazards associated with the breathing of respirable dusts, particularly silica dust, during mining are becoming a great concern in many parts of the world. The search for effective and low cost dust control methods for underdeveloped countries will help in improving the productivity and keeping the mine environment safe. This article addresses the problem by providing suggestions concerning the easiest and most cost effective methods to control respirable dust in mining and mineral processing operations. INTRODUCTIONMedical BackgroundLung diseases caused by dust in mining operations have been recognized by mankind since the time of the Roman Empire. The writings of Pliny the Younger on natural history reported on maladies associated with dust in mining in the first century AD. However, no significant advances in controlling the lung diseases of miners came about for many centuries. The effects of mineral dusts were further described by Georgius Agricola in his sixteenth century book on mining (Agricola, 1556). After the appearance of Agricola""s book, lung diseases were more readily recognized, but the nature and severity of the ailments associated with mineral dusts could not be readily interpreted.In 1896, the discovery of x-rays by Roentgen advanced the diagnosis of lung diseases and the knowledge of what causes these diseases. In addition, the discovery allowed medical personnel some method of judging the extent and severity of the lung diseases in human beings. During the ensuing years, the term 'pneumoconiosis' became the common term to describe any of the diseases of the lung in which dust particles deposited in the lungs caused fibrous tissue and loss of some of the respiratory function. However, little in the way of social remedies for the diseases resulted until much later. Society was still not ready to act decisively to reduce the causes of lung disease due to the dusty conditions in the work place.Social action against lung diseases did not occur in the United States (US) until the 1930s. At that time, a tunnel driven through a sandstone mountain near Gauley Bridge. West Virginia, caused the death of several hundred workers due to acute silicosis, a severe form of pneumoconiosis caused by silica (Seaton, 1975). Dust conditions in this tunnel were quite bad, causing many of the workers to be subjected to extremely high silica dust concentrations. The severity of the disease in many of the workers became known to the public and prompted the US Congress and many of the states to enact laws to reduce the dust levels."

Jan 1, 1998

By Van H. Manning

EXPLOSIVES RESEARCH. As the physical laboratories of the explosives section of the Pitts- burgh experiment station were equipped for testing the physical properties of explosives, both the Army and Navy Departments for many years had requested the Bureau of Mines to make such tests. Chemical control of the physical tests through analyses, heat tests, analyses of gaseous products of combustion, and sand tests was exer- cised through the explosives chemical laboratory. Often an investigation was cooperative between two laboratories. The explosives chemical laboratory also aided the work of the Ex- plosives Regulation both by chemical tests and investigation of acci- dents in explosives plants. COOPERATIVE WORK FOR ARMY AND NAVY DEPARTMENTS. The explosives chemical laboratory devised, at the request of the Bureau of Ordnance of the Navy, a more economical method of making hexanitrodiphenylamine. This problem was assigned to the Bureau of Mines by Dr. C. E. Munroe, chairman of the committee on explosives of the National Research Council, acting as the depart- ment of science and research of the Council of National Defense. Before the United States entered the war the following reports of investigations were submitted to the Army or the Navy: 1. Report of sensitiveness and relative efficiency of TNT and ammonium picrate, dated February 6, 1913, undertaken at the re- quest of the Chief of Ordnance. 2. Report of tests and examination of two samples of TNT and one of TNA for the Ordnance Department of the Army, dated August 5, 1915, was undertaken at the request of commanding officer, Frankford Arsenal. 3. Report of tests for sensitiveness to detonation of mercury ful- minate of 21 samples of TNT crystallized from various solvents, for the Bureau of Ordnance, Navy Department, dated June 17, 1916. 4. Report of tests of two samples of mercury fulminate for Frank- ford Arsenal, dated December 2, 1916, undertaken at the request of the commanding officer, Frankford Arsenal. After the United States entered the war the following reports of investigations were submitted: 5. Report of pendulum friction and large impact tests on two samples of "sodatol" and two samples of "amatol." The final report was dated July 20, 1918; and the preliminary report, May 15, 1918. This investigation was undertaken at the request of the Ordnance

Jan 1, 1919

By Francis Church Lincoln, Paul Zinner

"Attention of the Bureau of Mines was first directed to the Gray farm area by the results of several exploratory churn-drill holes completed by the New Jersey Zinc Co., and later by Roland J. Teske and by Judge H. L. Heer.When the Bureau of Mines initiated its investigation of the area, all drilling on the Gray farm had been discontinued, and no mining had resulted from the exploratory work. However, in the opinion of the Illinois Geological Survey, the Federal Geological Survey, and the Federal Bureau of Mines, this drilling,with the preliminary geological studies, was considered sufficient evidence to justify continued exploration to the southeast along a projection of the trend of mineralization developed in the mines to the northwest, or the so-called Black Jack Trough.This report describes the work done and presents the data obtained during the period of Bureau of Mines exploratory work.In its program of exploration of mineral deposits, the Bureau of Mines has as its Primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision or Dr. R. S. Dean, assistant director.Special acknowledgment is due Paul Herbert, geologist, Illinois Geological Survey, for his studies of cores, which greatly influenced the planning and progress of the exploratory work. Acknowledgment is also made to A. F. Agnew and A. V. Heyl, geologists, Federal Geological Survey, for their invaluable aid; to 0. W. Terry, F. C. Lincoln, M. H. Berliner, A. M. Cummings, project engineers; and to E. P. Barrett, district engineer, Minneapolis, and E. D. Gardner, regional engineer, Rolla, Mo., for supervising the program.The Gray ore body is on the Gray farm 5 miles south of Galena in Jo Daviess County, northwestern Illinois. The location with respect to adjoining properties is shown on figure 1. Galena is a city of 4,000 population on the banks of the Galena River, a stream that was formerly navigable by Mississippi River steamers but has now shrunk to the dimensions of a small creek. A gravel road leads from the city to the Gray farm and onward to the Bautsch and Boevers farms to the south of it."

Sep 1, 1946

By J. P. McGee

The Bureau of Mines is doing research and development work on a coal-fired gas turbine plant initially developed by the Locomotive Development Committee, (LDC) of Bituminous Coal Research, Inc. The Bureau is redesigning the turbine blading and some of the auxiliary equipment, and is reerecting, the plant at the Morgantown (W. Va.) Coal Research Center. The present goal is a 1,500-hour run at virtually the same operating conditions used by the LDC in their final 1,100-hour test with the turbine. This will allow the Bureau to properly evaluate the new blade design. Erosion of the turbine blades (particularly the roots) by ash in the hot gases from the combustion of coal was the most serious problem in extended operation in earlier experimental work. New blades made of Stellite6 are being fabricated for the stator and rotor, and armored wear strips of titanium carbide will be inserted in the blades at the areas of probable maximum ash velocity and concentration. The trailing edges of the rotor and stator blades are being thickened and thinned, respectively, to induce the ash to travel to the casing and prevent it from returning to the base of the rotor blades. The first stage rotor and second stage stator blades are being removed to provide an annular space for maximum quantities of coal ash to centrifuge to the casing. Additional blades will be added to most of the rows in the stator to stop secondary flow of dust-laden gas toward the rotor. A contract has been awarded for fabrication of the new blades. The 1,500-hour run will be started as soon as the new blades are installed.

Jan 1, 1962