Search Documents

By R. H. Fernald, C. D. Smith

When the United States Geological Survey began operations at the coal-testing plant erected at the Louisiana Purchase Exposition at St. Louis, Mo., in 1904, it had already outlined a comprehensive plan for the systematic study of coals, lignites, and other mineral fuels with reference to their suitability for particular purposes and the methods by which they could be utilized most efficiently. Recognizing the need of information on the relative economy of producer gas as compared with steam for power purposes and the lack of comparable tests of American coals in the gas producer, the Geological Survey undertook investigations of the merits of different coals as producer fuel for the purpose of promoting efficiency in the utilization of the nation's fuel supplies. These investigations were carried on at St. Louis, Mo., and, later, at Norfolk, Va., and Pittsburg, Pa. The aet of Congress approved May 16, 1910, transferred the fueltesting work being carried on by the Geological Survey to the Bureau of Mines. This bureau is conducting producer-gas tests at P~ttsburg, Pa., and is publishing and distributing reports relating to all the fuel tests made by the Survey. These investigations into the possibility of generating producer gas in a commercial way for power purposes from the various fuels of the country have been associated with steaming, briquetting, coking, and other tests, all of which supplemented an examination into the nature, extent, and distribution of the fuels. The tests have all been made with carefully selected representative samples and carload lots of materials procured specially for the purpose by experienced collectors.

Jan 1, 1911

By Dupuy. Leon W., R. T. C. Rasmussen, W. A. Calhoun

"INTRODUCTION For many years it has been known that low-grade manganese deposits occur in the bluffs along the Missouri River Valley. Frequent attempts have been made to develop the ore and to produce a marketalble commodity but they have had little success. Under pressure of the war emergency and the shortage of manganese, the attention of the Federal Bureau of Mines was directedtoward the deposits.Manganese-bearing shale occurs from a point near Pierre, S. Dak., down the river to the Rosebud bridge near the Nebraska line (1).5/ The Bureau of,confined its work to the more accessible central portion of the deposits near Chamberlain, S. Dak. The ore occurs principally as concretionary nodules in the form of iron and manganese carbonates (manganosiarite and perhaps some manganocalcite; rhodochrosite has not been identified). At the surface the carbonate is often broken down so that the oxide of manganese gives the nodules a black The matrix or host rock is generally known as Pierre shale, composed of ""interbedded layers of bentonite, an altered volcanic ash, and dissemi¬nated bentonite particles,"" (2) and montmorillonite-beidellite clay minerals (3). The shale weathers to the very sticky gumbo characteristic of South Dakota and well-known to hunters and travelers in the area.The area selected for the experimental mining and pilot-plant work discussed in this report lies about 8 miles westerly from Chamberlain and is a few hundred feet north of U. S. Highway,16, on land owned or controlled,by M. Q. Sharpe of Kennebec, S. Dak., and the General Manganese Corp."

Feb 1, 1946

By J. B. Gayle

In a modern blast furnace, production depends, to a large extent, on the rate at which the furnace gases can be forced through the charge. Since these gases must make their way through the voids between particles of coke, ore, and limestone, the size and size distribution of the stock-column materials are of considerable importance. Also, because the coke pieces support the weight of the overburden and provide the majority of the voids through which the gases pass, their ability to withstand the shattering and abrading forces to which they are subjected should be related to the maximum obtainable production for any particular furnace. Although the wide acceptance of this point of view is indicated by the ever-increasing demand for stronger and more uniform blast-furnace cokes, economic considerations demand that a quantitative evaluation of the relation between coke quality and blast-furnace performance be made available to the industry at the earliest possible date. The following studies of size-distribution patterns and breakage processes were, therefore, conducted as a part of a preliminary investigation intended as a basis for future studies of the relation between coke quality and blast-furnace performance. The major findings may be summarized as follows: 1. New evidence for the presence of two independent distributions of sizes in run-of-oven cokes has been obtained, and a method for characterizing and estimating the relative importance of the individual distributions has been demonstrated. This method has also been used to study the different types of degradation taking place during the tumbler test.

Jan 1, 1954

By Benjamin Petkof

Production quarry blasts in three rock types were photographed with a high-speed camera. Analysis of the films showed that step increases sometimes occur in the horizontal velocity of the broken rock. These step velocity increases were observed only in the first foot or so of rock movement. This observation indicates that the gaseous products of the explosion do additional work on the rock after it is crushed and cracked by the initial compressive-stress pulse and the reflected tensile-stress pulse. The observed initial fly-rock velocity is compared with the calculated fly-rock velocity for reflection spalling. A mechanism possibly causing the velocity increases is discussed. INTRODUCTION When a small concentrated charge of explosive is detonated at the bottom of a drill hole near a free surface, two modes of rock failure have been observed; both are associated with the stress pulse generated in the rock by the detonating explosive. The first mode of failure is the crushing and radial tensile cracking associated with the initial passage of the compressive-stress pulse as it propagates outward from the explosion. This type of rock failure is usually confined to the immediate vicinity of the charge hole. The second mode of failure is the tangential and radial tensile cracking associated with the tensile-stress pulse that is reflected from the free surface. This mode of failure is commonly called scabbing or spalling and has been shown to be a primary cause of rock failure in crater formation at one free surface. (3).4

Jan 1, 1961

By Xavier B. Starnes

"SUMMARYThe J. D. Price property is in Crittenden County, Ky., about 5-1/2 miles west of Marion. The Levias-Crittenden Springs fault system traverses the property. Mines on 3 miles of the same fault system immediately northeast have produced about 250,000 tons of fluorspar ore. The Keystone property, adjacent on the northeast, has produced about 150,000 tons of ore. 3/About 1934, lessees, sank a shaft upon the Price property to a depth of 111.5 feet and crosscut from the bottom of the shaft to the principal fault. No ore was found. Later, in 1942-43, they explored the same fault by core-drilling, but this project also was unsuccessful in finding ore.The author visited the property in September 1944, and subsequently the Bureau further explored the property by core-drilling three holes. No ore was found.ACKNOWLEGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. This ex¬ploratory project was under the general supervision of E. D. Gardner, regional engineer of the Central Region, and 0. M. Bishop, district engineer, Bureau of Mines. The mining branch is under the direction of L. B. Moon. The work on the project was under the direct supervision of Xavier B. Starnes, mining engineer."

Jun 1, 1947

By P. S. Jacobsen

In 1960 over 93 percent of the coal cleaned mechanically in the United States was cleaned in processes that utilized water or dense-medium suspensions of fine solids in water. Thus, in the process of removing deleterious ash-forming and sulfur-bearing minerals, another deleterious substance--water-- is added to the coal. The subsequent removal of the water from the coal, and the concomitant recovery of the coal from the water, is not troublesome in the sizes coarser than 1/4-inch. In the finer sizes, however, it is a difficult procedure that often costs more than the original washing operation. Because of the importance of liquid-solids separation in coal preparation, the Bureau of Mines has a continuing program of research in this field. The objective is to make available information on the performance characteristics of various types of equipment available for liquid-solids separations, thus promoting the wise selection of equipment for specific applications, and, thereby, more effective processing of coal. Results of work on flocculation as an aid to filtration5 and the sieve bend screen6 have been published. The present investigation of the screw-type classifier operating in combination with the cyclone was undertaken primarily because such classifiers are comparatively new to coal preparation and information on their performance is not available. The cyclone has become well-known since its introduction in this country by the Bureau of Mines in 1948.7 Use of the cyclone in conjunction with the screw-type classifier represents an attempt to provide the maximum recovery of solids at minimum moisture content.

Jan 1, 1962

By Eugene Frey

"INTRODUCTION The Blue Bell fluorite deposits were examined in August and November 1944 by an engineer 3/ of the Bureau of Mines, and an underground project was set up. The Bureau of Mines began development of fluorite here February 10, 1945, and completed its survey on June 21, 1946.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepared the final report. The Metallurgical Branch, C. C. Ralston, chief, analyzes samples and perform beneficiaticn tests. The exploratory project was under the direction of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch. Acknow¬ledgment is due R. Thurston of the Federal Geological Survey for mapping the topography of the area, and to F. H. Gunnell and W. A. Young of the divisional office for detailed mapping of the surface and underground development and interpretation of the results.The chemical analyses included in this report was performed under the direction of H. E. Peterson, analytical chemist; the petrographic studies on the ore were written by LaMar Evans, petrographer; and the beneficiaticn section was written by C. H. Schack, metallurgist, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

Jul 1, 1947

"The Generic Mineral Technology Center on Respirable Dust was established in August 1983, at the request of the Bureau of Mines, to conduct research that affords ""...each miner the opportunity to work underground during the period of (his/her) adult working life without incurring any disability from pneumoconiosis or any other occupational disease"". The Center consists of the Mining and Mineral Resources Research Institutes (MRI) of The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with the MRIs of the Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). (FIGURE 34) Michigan Technological University (MTU) is also affiliated with the Center in the area of diesel particulates.The Center brings together experts concerned with particles causing potentially disabling or fatal diseases including pneumoconiosis (""black-lung""), silicosis, and asbestosis. The latter is of deep concern not just to workers in the mineral sector of the economy but also to the general populace. The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The research program of the Generic Mineral Technology Center explores these scientific, engineering or medical concerns with the objective of refining existing strategies and developing new respirable dust control techniquesand technology that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on five areas (FIGURE 35):"

Nov 1, 1988

By Grant R. Brown

This report presents the results of a study examining the relationship between supervisor characteristics and performance in underground coal mines, The specific objectives of the research include; document tasks performed by first-line supervisors during a normal shift; explain why supervisors carry out their duties as they do: identify salient characteristics of effective first-line supervisors; and formulate criteria for selecting and developing candidate supervisors. To accomplish the study objectives, on-site observation and data collection was carried out at 13 underground mines in Illinois, Ohio, and Pennsylvania. One hundred thirty-eight first-line supervisors were observed during a full work-shift and discussions with the supervisors and the mine superintendent were held during the course of the visit. The observational data from the study provide a detailed description of what supervisors to during their shift. The report begins with an introduction discussing the problem being studied and objectives of the research. The literature related to supervisor selection is then reviewed. The following section describes the research design including data collection procedures and statistical methodology used in the study. The next sections present the analysis of mine, section, crew, and supervisor characteristics. The report concludes with a discussion of the results of the study and recommendations concerning supervisor selection and development.

Jan 1, 1987

By R. P. Vinson

The Bureau of Mines conducted a series of tests to determine how well the Bendix BDX 60, the Gilian HFS 113U, the MSA Fixt-Flo, and the Spectrex PAS-3000 dust sampling pumps control the flow rate at 2 L/min. These tests were performed because users need to know the performance characteristics of sampling pumps to select the pump that best satisfies their sampling requirements. Long-term (6- to 8-h) flow stability at various backpressures was examined in relation to the flow control tolerance of ±5% of the flow, the level imposed by Federal regulations; four of the five Bendix pumps did not meet the criterion for this test, which was passed by all other pumps tested. Flow control recovery times were measured at transient backpressures; all pumps evaluated met the criterion for this test. The low-flow indicators of the sampling pumps were tested; only two Bendix pumps and one Gilian pump met the criterion of indicating a flow change greater than ±5%. In the pulsation flow measurement test all of the pumps passed, with pulsating flows greater than 20 Hz. The Bureau also evaluated the manuals accompanying the sampling pumps. All were judged adequate except the Spectrex manual, which was judged poor.

Jan 1, 1985

By R. V. Ramani

This volume is the second of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume III: Mine Coordinate Generator System, and Volume IV: User's Manual for OPMHS/2. The dragline model described in this report simulates the movement of the dragline bucket across the digging face, the swing load, the dump, and swing back. It is programmed to handle chopdown, key cut, main cut, and rehandling operations. Provisions have been made for simulating equipment and mining delays. Any mining method can be specified in terms of numbered blocks, the dragline positions for the mining block and the dumping location for the block. Accounting procedures permit the calculation of production rates, rehandle volume, dig and delay times. The model can be used to study the effects of varying mining conditions, cut width, and spoiling sequence with special reference to toxic spoil, overburden and bench removal procedures. The basic input data for the model include machine parameters, the geology and material characteristics, the mining parameter, and the delay characteristics of the equipment.

Jan 1, 1985

By L. D. Tracy

"The first study of this subject has been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal—mining industry to standardise the forms of leases, and so avoid some of the abstruse and ambiguous clauses which may be found in many of then and the consequent liability of costly litigation.In some of the publications of the Illinois Mining Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the State have been dividedinto eight geological districts, each district being treated separately.report covers District No. VI of that classification, and it is hopedstudies of the other districts will be completed in the near future and similar results published.The report includes a short description of the geological condition the character and quality of the coal and the nature of the surface, data for which have been taken largely from the Illinois Geological Survey publications.Mining methods and percentages of recovery are mentioned, together physisal conditions, market and transportation facilities, because all of these factors have a bearing on royalties and leasing conditions."

Jan 1, 1926

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991

Reduce dust at the auger mine face by modifying airflow patterns, around the minim machine. Approach Limited clearance between an auger miner and the mine root restricts airflow across the face and causes dust rollback. Directional sprays arc used to direct air across the face, thereby reducing dust rollback and increasing dust dilution (fig. 1). Laboratory and underground studies were used to test and optimize effectiveness of the directional sprays. Results of Laboratory Study Laboratory experiments were conducted in a simulated auger gallery equipped with a full-scale mock auger miner and bridge conveyor. A dual curtain configuration was used to direct the, ventilation, which averaged 2,700 cfm throughout the experiment. Testing variables included spray location, pressure, spacing, orientation, and number. Figure 2 shows the optimized directional spray system, also called the auger clearer spray system. The system consists of three sprays mounted alone the intake side of the miner. Sprays arc spaced 16 to 24 inches apart, and angled 30° toward the return side of the miner. The 24-inch spacing moved about 7% more air across the face than the 16-inch spacing; however, it resulted in some additional misting on the return side of the miner. A 30° orientation was more effective than a 60° orientation for moving air across the face and minimizing misting on the return side of the miner. Flat fan sprays arc used because their spray paths arc not obstructed by the top of the miner and mine roof, A 50° fan angle is used to minimize misting on the intake side of the miner.

Jan 1, 1989

By William E. Dennis

"INTRODUCTION The San Antonio Canyon prospect was examined by engineers 3/ of the Bureau of Mines in March 1943 and again in October 1944. In July 1944, the United States Geological Survey mapped the prospect and submitted a report 4/ recommending core drilling by the Bureau of Mines. The drilling project, which was supervised by the author, was started on January 10 and completed on May 10, 1946.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. Acknowledgment is made to W. D. McMillan, engineer in charge of the Austin field office, and to J. H. Hedges, chief of the Tucson Division, Mining Branch, for general direction and advice. The samples were analysed in the laboratory of the Metallurgical Branch at Rolla, Mo., C. Travis Anderson, chief."

May 1, 1947

By John B. Goodman

This report presents a study of a modification of the precision laboratory carbonization-assay apparatus that renders the unit capable of performance at low-, medium-, and high-temperature assay levels and permits, under controlled conditions, evaluation of the relationship between carbonization temperature and the yield of pyrolysis products. Second, the interest and value derived from the temperature study data directly apply to the particular semiplant carbonization processes and techniques currently being investigated in this laboratory. Data obtained with the assay apparatus enables the fuel technologist to predict the probable yields of carbonization products from pilot-plant operations under various carbonizing conditions. Data obtained with the assay apparatus has been used to predict the product yields of industrial carbonization plants at Kemmerer, Wyo., and Rockdale, Tex. The assay provides a useful tool in detecting, from the carbonized plant product, the degree of effectiveness of pilot-plant operation. Third, the residual volatile matter in some industrial carbons has broad significance. Evaluation of the volatile material remaining with or in the carbon may be assessed through the high-temperature-assay technique. The low-temperature carbonization assay devised by the writers has proved to be a versatile tool in predicting the probable product yields from pilot-scale carbonization processes. The apparatus described in previous publications has been modified to extend the range of testing above 500° C. without impairing the accuracy and reproducibility obtained in the low-temperature range. Results presented here include product yields from a typical Texas lignite and Wyoming subbituminous-B-rank coal over the temperature range 150° to 1,000° C.

Jan 1, 1958

By Kenneth Eilerts

The development and operation of "combination wells"5/ have created new and unusual problems, many of which can he solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to know, whether liquid will be formed in the reservoir as a result of isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how pressure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios off gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and. pressure of the system are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the Fluids under reservoir conditions are particularly important at this time, To meet the immediate requirements of the industry for such experimental information, an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date have been accumulated, it may be possible to make dependable estimates of the phase relations for high gas-liquid ratio fluids at the pressures anti temperatures characteristic of "combination-well? reservoirs.

Jan 1, 1940

Develop a down-hole replaceable diamond core bit that will reduce overall drilling costs and increase total available drilling time per hole. Approach A one-piece diamond core drill bit of unique geometric shape has been designed, fabricated and field tested. The bit can be withdrawn (or replaced) from the bottom of the well-bore without removing the drill rods from the hole, saving a significant amount of non-productive drilling time. How It Works The replaceable bit system consists of two basic subsystems: the removable core bit, and the equipment necessary to replace the wornout bit without pulling the drill rods out of the hole. The geometric configuration of the bit is that of a one-piece diamond studded cutting element created by "slicing off" two parallel sides of a conventional diamond cone bit. This geometric configuration, along with some minor modifications to the outer core barrel, allows the bit to be rotated in two planes and, with the retraction-insertion tools, raised or lowered through the interior of the drill rods using a conventional wire-line system. For example, to retrieve the bit, a retraction tool is lowered through the drill rods using a conventional wire-line system and at the hole bottom, the tool automatically orients itself within the outer core barrel.

Jan 1, 1981

By J. E. Emmerling

The Federal Bureau of Mines investigated dust suppression obtained with three different water-spray nozzle systems during underground continuous coal mining at the face. The nozzles were the "regular" nozzle normally used by the mine, and high-efficiency and low-efficiency nozzles selected on the basis of an airborne capture theory of respirable dust by spray drops. The high-efficiency nozzle used one-third less water than the others throughout the testing. Results depended on the type of cutting operation at the face. The sump-downshear operation appeared to involve a significant amount of capture of airborne respirable dust. The same amount of dust was measured when using the high-efficiency and regular nozzles. The dust levels when using the high-efficiency nozzle were about 20 pct less than those measured when using the low-efficiency nozzle. The sump-upshear operation seemed to involve a predominance of other aspects of dust suppression, such as impaction of spray drops onto the face. Compared with the downshear operation, there was a significant reduction in dust levels for a total face operation when using the regular nozzle; dust levels when using the regular nozzle were about 15 pct lower than those measured when using the high-efficiency nozzle.

Jan 1, 1975

Reduce costs of surface mine reclamation by improving scaper operating efficiency and reducing tire costs. Approach The Wheel Slip Monitor senses and compares the peripheral speed of a scraper's four tires 10 the true ground speed of the scraper, and alerts the operator if any of the tires exceeds a predetermined amount of slip. This system helps scraper operators reduce wheel slip during the loading cycle, thereby improving the loading efficiency of the scaper and reducing tire wear and damage. How It Works The system consists of five ultrasonic doppler velocity-sensing devices for measuring the speed of each wheel as well as the true ground velocity (see photograph). Each sensor produces an electrical output signal having a frequency proportional to the speed of the tire or terrain. The signals are conveyed through electrical cables to a control box in the operator's cab where they are converted to voltages proportional to individual wheel speeds (see photograph). The signals are further processed to activate a blinking red light, corresponding to any individual wheel which is slipping, and to sound a beeping tone that is audible to the scraper operator. The rate at which the light blinks and the tone beeps is proportional to the degree of slip. Alerted, the operator can take corrective action.

Jan 1, 1985