Search Documents

By Spencer P. Howell, J. F. Xrawshaw

"A recent premature explosion in a quarry that resulted in the death of nine men and the injury of several others, was directly traceable to a spark from a steam-shovel working under the face directly in front of the hole being loaded. This accident and similar accidents on record in the Bureau of Mines indicates the necessity for pointing out the dangers in quarries of explosives being ignited by sparks emitted from steam shovels and locomotives, and making recommendations for greater safety.Many premature explosions of which the following are examples, have resulted from sparks, both from steam shovels and passing locomotives. (A) The premature explosion occurred during August, 1920 at a limestone quarry, in a 100-foot drill hole, loaded with 1000 pounds of high-grade nitroglycerin and gelatin dynamites. This hole had been loaded with 500 pounds of 75 per cent strength gelatin dynamite, 300 pounds of 60 per cent straight nitroglycerin dynamite, and 200 pounds of 50 per cent straight nitro¬glycerin dynamite; but no steaming had been placed in the hole. The powderman loading the hole saw the spark enter the hole and was able to run a short distance before the explosion took place, thus escaping serious injury. The explosion of this first hole was transmitted to nearby hole similarly charged. The fall of rocks from these two holes buried the steam shovel and some of the gang of men working around it.(B) In September, 1909, in the Canal Zone, a steam shovel uncovered a misfired charge of dynamite. While the dynamite was being picked up the steam shovel continued working nearby. A spark from the shovel set fire to some loose dynamite spilled on the ground from the troken cartridges. This fire was transmitted to a hole which was being loaded close by and caused a premature explosion. One man was injured."

Nov 1, 1920

By R. V. Ramani

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a mine located in Illinois using bucket wheel excavator (BWE) and a stripping shovel in tandem for overburden removal is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and scheduling problems and to generate and analyze alternatives for increased production. On the basis of the simulations it was concluded that the maximum productive capacity of the system in raw coal was around 3000 tons per shift. At this production level, the equipment combination and availability also satisfy the match requirements for the stripping shovel and the BWE, and the overburden and coal removal systems. Several alternatives requiring new equipment are proposed and analyzed for increasing production. However, no economic analyses of these proposals were done.

Jan 1, 1977

By H. H. Storch

Methane is the chief constituent of natural gas, and large quantities of it are also obtained in coke-oven gas and in the off-gases from cracking higher hydrocarbons. Perhaps the most important potential chemical use of methane is in the production of higher hydro- carbons, both aliphatic and aromatic. The results of a relatively large number of researches have been published in the technical and patent literature on the thermal decomposition of methane, the objective being an industrial process for the production of "antiknock" motor fuel. No industrially feasible process has, however, been developed. An inspection of the literature on this subject indicates that the chief difficulty in the way of accomplishing this object lies in controlling the decomposition so that undesirable products are eliminated. A considerable number of quantitative experiments have been reported, the results of which provide only a vague and confusing picture of the various steps in the thermal decomposition of methane. The reaction mechanism has not been subjected to rigorous fundamental study, and the necessity for such a study is obvious if further progress is to be made. The thermal decomposition is only one of the reactions of methane which are of potential industrial importance and which require further fundamental investigation. The oxidation, hydrolysis, and halogenation of methane are other reactions which must be studied further. In view of the importance of methane as a raw material for various industrially desirable products, it is appropriate that a survey be made of the important facts concerning the physical and chemical properties of methane which will serve as an aid in subsequent experi- mental work. No attempt will be made to present a complete chronological review, but rather a condensed critical description of the important literature will be presented.

Jan 1, 1932

Coal is a combustible, carbonaceous, sedimentary rock that is formed by the accumulation, compaction, and physical and chemical alteration of vegetation [Simon and Hopkins 1981; Bates and Jackson 1987]. Coal is classified according to its type, grade, and rank. The type of coal relates to the plant materials from which the coal originated. The grade of coal refers to the purity of the coal-or the amount of inorganic material (including ash and sulfur) left after the coal is burned [Bates and Jackson 1987; Stefanko 1983]. The rank of coal indicates its degree of metamorphosis and roughly correlates to the geological age of the coal or the geological environment from which it has been mined [Bates and Jackson 1987]. Rank also indicates the percentage of carbon in dry, mineral-free coal [Whitten and Brooks 1973] and the degree to which the coalification process has progressed [Larsen 1981]. The geological process of coalification begins with organic materials (e.g., celluloses, lignins, and other plant compounds that are deoxygenated and then dehydrogenated) and ends with coal of various geological ages, from lignite to anthracite [Larsen 1981]. Table 3- 1 presents the American Society for Testing and Materials (ASTM) classification of coals by rank. According to Parkes [1982], high-rank coal includes anthracite and semianthracite coal ("hard coal," with 91% to 95% carbon); intermediate-rank coal includes low-, medium-, and high-volatile bituminous and sub-bituminous coal ("soft coal," with 76% to 90% carbon); and low-rank coal includes lignite (with 65% to 75% carbon or less). The rank of coal tends to increase from the western to the eastern United States, with anthracite occurring primarily in eastern Pennsylvania [Schlick and Fannick 1971]. Most of the coal currently mined in the United States is bituminous [Given 1984]. A classification of the coal in the United States is provided in Table 3-2.

Jan 1, 1997

By Roy Greenfield

Estimates are given for the distance from a seismometer at which a miner can probably be detected. The procedure in making these estimates was to first establish the natural noise levels at the output of a surface seismometer for the 25 to 100 Hz frequency passband. The noise levels give the range of values which may be expected in areas with no man-made noise. For each noise level, we give the detection threshold which, when exceeded, indicates that a signal has been received. Based on the signals recorded by Westinghouse, curves are given which show the peak signal amplitude as a function of source- to-receiver distance (slant range). Curves are given for the Westinghouse seismic thumper, a 50-pound timber, and a sledge. For a given type of source, the receive signal strength depends more strongly on slant range than on any other factor. However, there is approximately a five-to-one scatter in the amplitudes. Thus, further study of factors affecting the signal amplitude might allow better estimates to be made for any particular geological setting. Combining the signal amplitude with the detection thresholds for the different noise conditions gives the distances at which a miner should be detected. These are given in Table l* below. [ ] The text also gives the increase in detection ranges which should occur if steps are taken to increase S/N by 10 dB. We feel that 10 dB is a conservative estimate of the improvement possible. During an actual rescue operation, the seismic crew and system should be capable of making on-site estimates of their detection capability, based on measurements of the site noise, and upon the best available estimates of the

Jan 1, 1974

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

By Rita D. Sylvester

"IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January I, 1965, to December 31, 1969. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January I, 1960;' the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January I, 1960;3 the 5-year list of Bureau publications and articles from January I, 1960, to December 31, 1964.' It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1965, to December 31, 1968, as well as the Bureau publications and articles for 1969."

Jan 1, 1970

By J. H. Holden

Operations involving the processing of coal, oxygen, and steam into synthesis gas by means of two pressure-type gasifiers have demonstrated the effect of heat loss and operating variables on carbon gasified and oxygen and coal requirements. Carbon gasified is the fraction of carbon in the coal that is converted to gas. Oxygen and coal requirement is the quantity of each that is needed to produce a unit volume (M std. c.f.) of carbon monoxide and hydrogen. Operating pressure of the gasifiers ranged from 150 to 300 p.s.i.g. and coal was fed at 200 to 500 lb./hr./cu.ft. of reaction-zone space. Oxygen-to-coal ratios were 8.5 to 10.5 std. c.f./lb. Heat loss and residence time have opposite effects on carbon gasified; increasing the heat loss decreases the carbon gasified, but increasing the residence time (by raising the operating pressure or reducing the coal-feed rate) increases the carbon gasified. The effects of these two factors are difficult to separate because they usually change simultaneously. A comparison of the results obtained from the operation of two gasifiers with different levels of heat loss, however, permitted the effect of heat loss to be separated from that of pressure and coal-feed rate. When the results were deter- mined on the basis of constant heat loss, increase of the residence time increased the carbon gasified until the reaction virtually had come to completion. For example, at 150 p.s.i.g., decreasing the coal-feed ratio from 500 lb./hr./cu.ft. to 200 lb./hr./cu.ft. substantially increased the carbon gasified. At 300 p.s.i.g., however, changing the coal-feed rate had little effect on the carbon gasified because the reaction had almost reached completion and further increase in residence time resulted only in a negligible change.

Jan 1, 1962

To determine the relative permeability of the soil a series of percolation tests were performed at the three locations of interest at Lanse, i.e., 3C, 03A and strip bank, and KA and KB at Kato. Soil cores were removed to 2, 8, 16, 24 and 32 inch depths with the thin wall sampler tube, each core separated from the next by about fifteen feet. Then two-foot-long thin-wall tubes were inserted into the 2, 8, and 16 inch deep holes and three-foot long tubes were inserted into the 24 and 36 inch deep holes. Each tube was tamped down about one inch further to assure a bottom seal; the tubes were filled with water and the rate of fall was measured. The test is similar to those done for septic tank percolation studies 6; but is not quantitatively related to Darcy's coefficient of hydraulic conductivity because the water can flow in three dimensions from the bottom of the tube. The measurements are dependent on the length of test, since the rate of fall is a function of the head. Therefore, it should be noted that the 24 and 32 inch deep tubes should give faster percolation rates because of the one foot greater head. At locations 03A and 3C the data show a sharp decrease in percolation at increasing depth, Table XV. However, the percolation at 03A and 32 inch depth is much higher than at 3C (0.2 vs. 0.01 inches/hour); the fragipan layer must be deeper at the 3C location since this area does experience a perched water table. On the strip bank the rates of falling head are randomly variable, appearing to be as much dependent on the particular location of insertion as on depth of placement. For example, water drained from the 16 inch tube as fast as it was added, probably into a sub-surface cavity or crevice. At Kato the tubes were more difficult to place because of interference of tree roots. For this reason 2 inch deep tubes were not inserted. These short tests at Kato were inconclusive, varying extensively when the tubes were moved. Field permeability tests were also performed in two (previously described) eight-inch diameter permeater tubes at Lanse and one at Kato. Because the soil is confined inside the tube, hydraulic conductivity can be calculated according to Darcy's flow equation. The high values reported in Table XVI experienced when the tubes were rewetted from a dry surface condition, enable us to conclude that infiltration is faster than the saturated permeability of the soil. In contrast to the falling head percolation tests, these permeability results do not show a high variation between locations.

Jan 1, 1972

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen's original discovery.

Jan 1, 1956

By F. du Breuil

BCR National Laboratory (formerly Bituminous Coal Research, Inc.), under a USBM con­tract (originally with the Department of Energy), monitored the installation and operation of a computer-based belt-monitoring and control system at the Barnes & Tucker Coal Co. Mine No. 20, Ebensburg, PA. The system installed was the National Coal Board's Mine Operating System (MINOS) coal transport monitoring and control system. The program objec­tive was to document (1) the installation requirements for a conveyor control system, (2) the operating experience with the system, and (3) the impact of monitoring and control on mine operation. Analysis of the system operation indicates that monitoring and control did improve belt availability significantly, and reduced downtime associated with belt delays. Economic analysis showed the increased belt availability would potentially result in significant production increase, and, therefore, excellent payback on the initial investment. The system performed satisfactorily, was well accepted by the work force, and did not increase the maintenance workload.

Jan 1, 1987

By William H. Schiffbauer

The U.S. Bureau of Mines has been investigating methods and technology that may improve safety and production when applied to existing mining machines. Toward those goals, the Bureau has developed navigation systems that provide machine positional information while in the production area. This research has been limited in the past because the Bureau had only one type of mining machine to do experiments. Addressing this problem, the Bureau, along with Carnegie Mellon University, has developed a generic vehicle emulator, in the form of a wheeled vehicle with an onboard computer, known as the Locomotion Emulator, that provides a software-selectable vehicle emulation package. Preliminary testing by the Bureau has shown that the emulator can accurately imitate the maneuvers of the software selected vehicle type. Now the Bureau can test their navigation systems on different vehicle types without having to procure each of the vehicles. This report completely describes the emulator as well as all the modes in which it can be operated.

Jan 1, 1991

By E. H. Burroughs

Persons interested in th_e study of petroleum and allied substances have long felt the need of a bibliographic index to the literature. This bibliography, which is intended to be the first elf a yearly series, has been compiled by the petroleum division of the Bureau of Mines with a view to satisfying this need. The references include only the more noteworthy writings that appeared during the year 191.5 in both ·the United States and foreign countries. Only patents plainly applicable to the industries in point have been included, although, of course, a close scrutiny of the great volume of patent literature might reveal many other patents of possible value. The references are arranged according to the subject classification on pages 3 to 11. This classification, which is to be followed in the succeeding bibliographies of this series, is offered as a guide for further study and classification of the pertinent literature.

Jan 1, 1918

By J. W. Town

Studies were made by the Bureau of Mines to determine the influence of textural features on the beneficiation of phosphate minerals (pellets) from selected bed and composite samples representing different rock types of the Western Phosphoria Formation. The particle size of the samples was reduced by attrition grinding to minus 20-, 28-, or 48-mesh depending on ore grade and gangue matrix. Sizing of the ground material showed that the phosphate pellets would concentrate in the plus 200-, 270-, or 325-mesh size fractions sufficiently so that the phosphate content was above the 31.5 :cent P2O5 required for acidulation. The phosphate content of essentially pure phosphate pellets was shown to range from 33 to 39 percent P2O5. Microscopic identification of the particles in each size fraction showed that the phosphate was either in the pellet form and readily liberated or so intimately associated with the gangue matrix that size reduction necessary Co obtain liberation was impractical.

Jan 1, 1967

By R. Lusignea

This report describes the development of a device for the nondestructive testing of resin grouted roof bolts by means of mechanical frequency response. Various alternative methods were evaluated and the mechanical frequency response method was selected. An interactive program of design, testing, and development culminating in the current prototype instrument demonstrated the capabilities of the method and suggested potential applications of the instrument. The resin bolt testing device utilizes a swept frequency dynamic compliance measurement in the 1 to 2 kHz range which is interpreted by an electronic signal processor to give a "GO" or "NO GO? readout. Field tests have shown that the device can reliably determine the bond quality of the front half of the bolt (nearest the roof surface). Tests were carried out on both experimentally installed bolts and typical mine bolts installed by a conventional bolting machine. The development program has led to recommendations for improvement of the prototype and future development work.

Jan 1, 1979

By Lloyd A. Morley

The primary goal of this research report is to discuss safety considerations involved in the use of lead-acid batteries for traction purposes in underground coal mines. In order to arrive at the objective, the topic of battery safety has been divided into two specific areas. The first deals with the fact that batteries emit hydrogen gas during and after the charge cycle. Hydrogen gas can be the source of dangerous explosions or mine fires. The second major topic deals with the electrical nature of the battery and battery-charging systems, which also provides a source of mine fires as well as electrocution hazards. In addition to the discussion on battery safety, a literature review has been undertaken to acquaint the reader with some basic concepts inherent to the battery usage process. The result of this research is a set of design specifications and procedural recommendations directed at improving the safety factors inherent in any underground battery usage scheme.

Jan 1, 1977

The extremely cold weather and heavy snowstorms of January and February in northeastern Pennsylvania--with frozen mining equipment, diminished preparation and lack of railroad cars--severely hampered the production and distribution of anthracite. As a result, the previous estimates for the 2 months have been revised. On March 1, 1977, at the Porter Tunnel of the Kocher Coal Company at Tower City, Pa., an underground flash flood, which apparently broke through the wall of an adjoining abandoned shaft, swept through the mine. As of March 9, 1977, four miners were reported killed, three injured, and five trapped in the wreckage. The Kocher Coal Company began operations at the Porter Tunnel in 1968 and has had no fatalities until this current tragedy. The mine employs 20 persons on the surface and 115 miners underground, producing 750 tons of coal per day. Of the 109 underground mining operations in the anthracite region, this is the one remaining large mine that employs over 100 men.

Jan 1, 1977

By B. H. Eccleston

The effect upon automobile emissions in changing from leaded to lead-free gasolines was studied in experiments by the Bureau of Mines in cooperation with the American Petroleum Institute. Typical U.S. leaded gasolines and prototype lead-free gasolines of comparable octane quality were used in eight vehicles operated to simulate city driving. The experiments were run at 70° and 95° F. Exhaust and evaporative emissions were measured and the photochemical effect of the emissions was experimentally observed in an artificial smog chamber. Results of the study reveal the manner and degree in which the changes in fuel composition alter the amount and characteristics of both exhaust and evaporative emissions. Briefly, it is shown that the compositional differences between leaded and prototype lead-free fuels resulted in higher photo-chemical pollution potential of the emissions from the lead-free fuels. The effect is attributed to the photochemical characteristics of high-octane fuel components that are used in greater quantity in the lead-free fuels.

Jan 1, 1970

By D. Harrington

As no cure is known for silicocis after it has developed, prevention is the only effective remedy. There are two main lines of approach to the problem of dust-disease prevention in industry - the engineering, through control of dust production, and the medical, through selection of workers by examination; success probably depends upon a combination of the two. Hatch (146) considers the following measures essential to a complete, well-balanced program of control of the dust hazard in industry: 1. Selection of workers by means of physical examinations in order especially to eliminate those with tuberculosis and other disorders of the respiratory system. 2. Reduction of the duct concentration below the standard of permissible dustiness through adequate moans of dust control and good housekeeping. 3. Limiting the frequency and duration of employment in the dusty occupations, thus reducing the rate of deposition of dust in the lungs. 4. Routine measurement of the effectiveness of the dust-control program by means of periodic medical examinations and duct surveys.

Jan 1, 1935

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938