Search Documents

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

By Arnold F. Stalder

The measurement of various gas concentrations in the atmosphere at a particular location has become a problem of considerable importance. Levels that need to be monitored vary from the range of percent for constituents such as oxygen to parts per million levels for gases like nitrogen dioxide. In particular, mine air can become contaminated with noxious or toxic gases from several sources: fires within the mine, diesel-powered equipment, and explosive sources. The contaminants that result are carbon monoxide (CO), carbon dioxide (CO2), and oxides of nitrogen (NO and NO2). Additionally, oxygen (O2) may be depleted. Thus, the workman can be exposed to potentially toxic or asphyxiating atmospheres. A device was needed that will continuously monitor the mine air in working areas and provide warning of hazardous atmospheres. The Mine Air Monitor was conceived as being a portable, rugged instrument capable of measuring the concentration of the various atmospheric constituents in the mine environment. The unit was to provide both warning signals and quantitative measurements when hazardous contaminants existed at too high a level, or when the oxygen was being depleted. The initial concept involved optical sensors for all of the contaminating gases to be measured, namely CO, CO2, CH4, and NO2, and an electrochemical cell to monitor O2. When the explosion proof requirements of Schedule 2-G made the concept appear to be unfeasible from the standpoint of weight and portability, the program was redirected and a three channel monitor employing electrochemical sensors was adopted. In this case the gases to be monitored were O2, CO and NO2. The remainder of the program was oriented towards obtaining good, commercially available lectrochemical sensors for the above gases, testing them, reducing deficiencies noted during these tests, and making the necessary modifications to integrate the three sensors into a Mine Air Monitor suitable for the mine environment.

Jan 1, 1974

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942

By R. V. Ramani, S. Shankar

"A convective dispersion model has been utilized to calculate the real-time airborne dust concentration in mine airways using re-entrainment as the only source term for airborne dust. It incorporates two important sources of re-entrainment in mines -- air velocity and movement of objects. The model has a sink term accounting for the deposition of particles along the airway. The model is solved using a finite difference scheme which is coded for computer. The computer model outputs airborne respirable and total dust concentrations along the airway as a function of time. The real-time and average gravimetric concentrations from several in-mine experiments were compared with the results from the simulation of the experimental conditions. This model can be used for estimating airborne dust entrainment due to air velocity, equipment movement, and persons walking. INTRODUCTIONEdwards and Ford (1988) developed a model for coal dust explosion suppression and utilized a predetermined value of threshold velocity for flowing air to pick up dust from floor. Depending on the strength of the removal forces, re-entrainment can increase the airborne dust concentration in mine airways. The most prevalent forces causing re-entrainment in mine airways are the drag and lift forces due to flowing air, and removal forces due to the movement of persons and vehicles. Shankar and Ramani (1991) have investigated the unique characteristics of the re-entrainment phenomenon in mine airways. Experiments on re-entrainment of coal dust particles were conducted in mine airways, and in a wind tunnel (Shankar and Ramani, 1994a, and 1994b). The results from the two experimental studies were found to compare well (Shankar and Ramani, 1995). There is no reported model to determine the airborne dust concentrations due to airflow or persons walking under conditions existing in mines. The present study is a part of a continuing research project in the Generic Mineral Technology Center for Respirable Dust on the spatial and temporal behavior of airborne dust in mine airways (Ramani, 1983)."

Dec 1, 1996

By G. E. McElroy, A. S. Richardson

"Experiments in the determination of friction factors for fan-pipe installations were carried on in a Butte mine during the fall and winter of 1922-23, under a cooperative agreement between the Bureau of Mines and the Anaconda Ccpper Mining Co. The results have been summarized in a separate paper,*** and this report, which is one of several giving more detailed data, discusses the methods used and the application of the results to fan-pipe practice.The use of canvas and galvanized-iron pipe, 8 to 20 inches in diameter, with small fans, usually electrically driven blowers, is an important factor in the ventilation of metal mines and is increasing in coal mines and long tunnels. In the Matte district the standard installation is an electrically driven small blower fan and 8 to 16 inch canvas pipe.The application of available data on friction losses in sheet-metal pipe to mine installations was doubtful, and very little has been published on canvas pipe, except general statements that the friction looses are greater than in galvanized-iron pipe. Experiments by Weeks and others,**** who determined friction losses under laboratory conditions for a few typical materials used in mine equipment, supported the statements.In 1918, one of the authors (Richardson) conducted tests for the Anaconda Copper Mining Cc. on the friction losses in canvas-pipe systems and the beet type of centrifugal blower for use with such pipe lines. He obtained the average total resistance per unit of length in use, without reference to the variable conditions of the lines. The results were of great value in developing more efficient equipment for average service conditions, and indicated that average friction losses for the commercial canvas tubing then used by the company were equal to or lees than these given for galvanized-iron pipe. Later on, the particular canvas tested was discarded for a heavier and more service-material."

Oct 1, 1923

"Fire fighting in metal mines under the best of conditions is a dangerous, a slow, and a difficult task. Certain gases generated from combustible material burning in restricted areas are poisonous, even in small quantities, and can not be breathed without serious and often fatal results. In addition to poisonous gases, smoke is given off which obscures the vision of the fire fighter and frequently prevents him from gaining access to the fire area. Many fire-fighting crews have had to turn back because their vision was so impaired by the dense smoke that the fire area could not be located and there was danger of them becoming lost in the mine.In mines having mechanically controlled ventilation - that is, mines not dependent entirely upon natural air currents - the gas and smoke can be forced ahead of the fire-fighting crews, thereby facilitating exploration of the mine and saving the time, energy and oxygen of the mine rescue apparatus crews.Where currents of fresh air can be circulated up to points near the fire without danger of seriously spreading the fire, fresh air bases can be established in the immediate vicinity, and a more intelligent campaign for fighting or controlling the fire can be mapped out.Positive air currents through forced ventilation may also result in saving the lives of miners who otherwise might have been trapped in smoke and poisonous gases.It is generally known that comparatively few metal mines have attempted to regulate or control air currents, with the result that when a fire occurs underground, the normal ventilation may be reversed, short circuited, or the air current may be in one direction one minute and in the opposite direction the next; or, generally speaking, the ventilation can not be depended upon, and smoke and poisonous gases may accumulate in any part of the mine or ""drift"" on the fire-fighters or on the miners endeavoring to escape."

Apr 1, 1921

By G. R. Hopkins, A. B. Coons

A survey of the petroleum pipe lines by the Bureau of Mines as of May 1, 1923, shows that on that date there was a total of slightly more than 90,000 miles of pipe lines in the United States, having a capacity of approximately 15,750,000 barrels, which is equivalent to one-fourth of the nation's average production for one month. These lines varied in diameter from 2 to 16 inches, the weighted average being 6 inches. The total pipe-line milenge was about equally divided between trunk lines and gathering lines, though the capacity of the former was about four times that of the latter. This was due, of course, to the difference in average diameter, that for the former being 7.4 inches as compared with 3.7 inches for the latter. The common size for trunk lines was 8 inches, and for gathering lines 2 inches. Oklahora, with 19,180 miles of pipe lines, is the leading State in total mileage, with Texas second and Pennsylvania third. From point of trunk lines alone Texas is considerably ahead of any of the other States, a position which it owes to its size and to the growth in the rovement to its Gulf ports. Cali- fornia, though the leading State from point of production, ranks only seventh in pipe-line mileage. This is due to the fortunate location of the Los Angeles Basin fields, some of which are within sight of the refineries to which their oil is delivered or of the port of San Pedro through which their oil is shipped. The last survey of this nature, made in the spring of 1924 by the U. S. Geological Survey, recorded a total mileage of nearly 83,000 with a capacity of approximately 14,450,000 barrels. This indicates an increase of 9 per cent in both mileage and capacity during the two years.

Jan 1, 1927

By Steven J. Page, Andrew B. Cecala, John A. Organiscak

In This Chapter [Drill dust control: wet and dry Enclosed cabs on drills and mobile equipment Haul road dust control] Overburden drilling generates most of the respirable dust that affects workers at surface mines. Both wet and dry methods are available to reduce this drill dust. Overburden removal by mobile excavation equipment such as bulldozers, front-end loaders, and haulage trucks can be dusty, particularly under dry and windy conditions. Tightly enclosed cabs with dust filtration systems can substantially lower the dust exposure of both drill and mobile equipment operators. Haul road dust control can be achieved by water application or chemical application. DRILL DUST CONTROL [Drill dust is controlled with wet or dry systems. Wet systems can be more efficient, but may freeze in the winter. Dry systems require careful maintenance of the drill deck shroud. An improved deck shroud is shown.] Wet Suppression. Wet drilling systems pump water into the bailing air from a water tank mounted on the drill. The water droplets in the bailing air trap dust particles as they travel up the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole [Page 1991]. In wet drilling systems, typical water flow rates are 0.1 to 2.0 gpm depending on the size and type of drill and the moisture level of the overburden. The drill operator controls the flow using a control valve located in the cab. Some drills are equipped with a flow meter to give the opera-tor a visual sign of the flow rate. Raising the water flow will improve dust capture, but too much water causes operational problems. Because of this, the drill operator must exercise care in find-ing the best water flow rate.

Jan 6, 2003

By Virgil A. Marple

The primary purpose of this contract was to evaluate methods and techniques by which the size distribution acid concentration of mining-related dusts can be measured. One result has been the development of a portable, battery-operated optical particle counter/ multi-channel analyzer system which can he used to determine the size distribution and concentration of mining aerosols. One important aspect of this program has been the development of a calibration technique which relates the output of the optical particle counter to the penetration of the particles through an impactor: This results in a calibration curve in terms of the aerodynamic or Stokes' diameter or the aerosol particles. Using this technique, calibrations were performed on coal, silica, Arizona road dust, potash, and rock dust (corer ore) aerosols. Another task of this program was the calibration and evaluation of the GCA respirible dust monitors (RMD) 101-1 and 301. The results of evaluation showed that the instruments were within the manufacturer's specification of ±25% of the true mass concentration up to about 15 mg/m , if the dust particles were in a size range from about 0.7 to 10 µm aerodynamic diameter. Particles smaller tan about 0.7 µm were not collected by the instrument and particles larger than about 10 µm were lose in the inlet. Other tasks included performing field studies in cooperative research programs with the Bureau of Mines personnel, development of a portable polystyrene latex generator for use in optical particle counter calibrations in the field. The incorporation of impactor classification devices on the inlets of aerosol mass measuring instruments to give mass size distributions, and a study of the density of coal particles as a function of the particle size.

Jan 1, 1977

To enhance safety and efficiency when moving large mining equipment under energized trolley lines, and to assist in compliance with Section 75.1003.2, 30 CFR. Approach A system was designed, using established technology, that permits a remotely located circuit breaker to be controlled from the cab of a mine locomotive moving large mining equipment under energized trolley lines. This control consists of setting the desired trip current, automatic or manual tripping, resetting, and voice communications between the locomotive and a remote Circuit breaker location. How It Works According to 75.1003.2, 30 CFR, whenever a piece of off-track equipment (such as a longwall chock or a continuous miner) is moved by rail under energized trolley or feeder lines, power for the locomotive that is moving the equipment must come from only one' circuit breaker. This circuit breaker must be adjusted to permit no more than one-half its rated short-circuit current to flow. The intent is to lessen the danger if an accident should occur, and if the equipment contacts the trolley line. Even so, the danger is great. This half setting can still represent many hundreds or even thousands of amperes, enough to endanger personnel, the equipment, or the mine. The Remote Control System reduces this danger substantially by giving the personnel associated with the move total control over the associated circuit breaker. The system as designed, is intended to be used with portable circuit breakers that are pulled on a small flat car by a mine jeep, and either precede or follow the equipment, depending on the direction of the power. This portable circuit breaker is equipped with a commercially available solid state overcurrent relay and associated shunt. This circuit breaker is connected via heavy duty clamps around an open trolley line tie breaker such that the current through the shunt is also the current in the trolley line. A receiver, interfaced with the overcurrent relay and shunt, completes the remote system.

Jan 1, 1981

By Charles H. Shapiro

[In July, 1924, the Bureau of Mines, through its Petroleum Experiment Station, undertook a field study of methods used in oil-field shops for dressing and tempering fishtail bits. The purpose of this work was to suggest chances that would be helpful to the bit-dresser in turning out better treated, harder, and tougher bits, and thus cut down the excessive loss of time caused by too frequent changing of bits. It was the intention to eliminate as much as possible the guess work connected with dressing and tempering bits under the method of judging temperature by eye, by developing; practical methods of controlling temperature. If there were some possible means of accurate temperature control, then it would be an easy matter to bring all bits to the proper temperature for maximum hardness rued toughness, thus doing away with the source of most of the trouble experienced in the present method of bit tempering. Shortly after the Bureau of Mines began its study, a chop In the Stroud, Oklahoma, oil field announced method for tempering fishtail bits that Would increase the drilling footage of each bit treated. The method accurately regulates, by the use of a bath of molten salt, the temperature to which a bit is heated before being quenched to produce hardness. There is nothing new in using silt baths for the, heat treatment of steel, but this was the first attempt to introduce it into the oil fields for use in hardening bits, and for this purpose it proved to be admirably adapted. In tempering, by the old system it is not possible to measure the temperature of the heated bit by means of an electrical instrument for that purpose, whereas this is an easy matter with the now method. If heating steel to slightly above the critical point rind quenching suddenly will bring out its best properties, their here is a method of accurately bringing the steel to that point.]

Jan 1, 1925

By James E. Norman

[The flotation of mica is mentioned frequently in the literature, but must of the references have dealt with the recovery of mica by the old anionic collectors. The first use of the new cationic reagents indicated their superiority- as collectors in the flotation and a. agglomerate tabling of micas, feldspars, quartz, clay, and other acidic mineral, but the separation n of these minerals from each other necessitated study of the flotation of each mineral.]

Jan 1, 1941

By Frank H. Reed

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation , and utilization of coal . This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British committee . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , Deputy Solid Fuels Administrator . The personnel of the mission consisted of H. F. Yancey, in charge , J. W. Buch, Thomas Fraser , L. L. Newman , and L. D. Schmidt of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology; H. J. Rose , Vice - president and Director of Research , Bituminous Coal Research , Inc .; and F. H. Reed , Chief Chemist , Illinois State Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These , together with microfilms of supporting data obtained in the course of the investigations , are on file at the Bureau of Mines , Washington , D. C. , where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproduction of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of $ 10 will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography, covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low- temperature carbonization processes ; metallurgical coke from

Jun 1, 1948

By Galen H. Clevenger, MARTINUS H. CARON

Although there are exceptions, oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. When these ores are of high enough grade they can be smelted; indeed, some rather low-grade ores of this type have been smelted at a profit because of their fluxing value. In the past, when these ores could not be smelted, they either were not treated or were treated at low efficiency, generally by cyanidation. The need for thorough investigation of the problem was therefore evident for some time before the writers began their research. The problem of treating manganese-silver ores seems to have been recognized first about 35 years ago by C. W. Goodale in applying pan amalgamation at Tombstone, Ariz. He attributed the low extraction of silver to the fouling of the mercury by manganese rather than to the presence of a refractory compound of manganese and·silver. Although definite knowledge as to the cause of the poor extraction of silver was lacking, a more or less effective preliminary treatment, that is, a chloridizing roast, was applied. E. M. Hamilton, in 1909, was perhaps the first to define clearly the problem as it affects the cyanidation of silver ores and to suggest possible methods of preliminary treatment. Most of the work done in the interval between the appearance of Hamilton's paper and the assumption of the investigation by the authors was in the nature of routine tests covering suggestions already made rather than of research directed to a fundamental study of the problem. No practical application has so far been made of any of these proposed processes. The investigation described in this bulletin has proved that there s a refractory compound of manganese and silver-probably a manganite- insoluble in cyanide solution and other common solvents for silver. Although this compound has not been isolated from natural ores, it has been made synthetically, and shows all the characteristics of the natural product. Furthermore the authors have shown definitely that heating in air a relatively small amount of a silver compound with a large excess of silica (in the proportions ordinarily occurring in a commercial silver ore) renders

Jan 1, 1925

By R. A. Cattell

The peacetime activities of the Bureau's petroleum and natural-gas program have been reoriented to serve the needs of a national-defense program. When the United Nations sent troops to Korea after the North Korean Army crossed the 38th parallel in the latter part of June 1950, the Bureau's coordinated national program on petroleum and natural gas, with each major project forming an essential member of its framework, was carefully reviewed by those in charge of the work. As a matter of fact, the era of normalcy in which the petroleum and natural-gas research of the Bureau of Mines prospered during the fiscal year 19502/ was no sedative to the need for alertness on a national-defense front. The program, although conducted along peacetime lines in general, was scanned critically and repeatedly during that period to see where - if the need should arise -the emphasis could be shifted from peace to defense or war. Judging from the experience of two wars, it would not be long before the Bureau would be asked to use its trained technical personnel in applying techniques already learned in peacetime research to the requirements of munition and fuel needs of national defense. Near the end of January 1951, petroleum and natural-gas engineers of the Bureau of Mines began a comprehensive study of reservoir conditions in the Canyon Reef fields of Scurry, Borden, and Kent Counties, Tex. This work was preceded by published analyses of crude oils from Scurry County as early as April 1950. Well-informed persons in industry have estimated that these fields hold reserves that will yield 3 to 6 billion barrels of stock-tank oil. Although generally accepted good operating practices have been followed, engineering tests have shown that the natural energy, except in some favorable parts of the reservoir, will not be adequate for obtaining a high percentage of recovery. Correct information regarding the extent and availability of this vast reservoir of hydrocarbons is therefore of great concern to the Petroleum Administration for Defense in carrying out its responsibilities under the Defense Production Act.

Jan 1, 1952

By D. W. Butner

This report is concerned with the conditions affecting the methods and costs of mining phosphate rock in that part of the western phosphate field that is in Bear Lake and Caribou Counties in southeastern Idaho ( see fig . 1) . The area was selected because it contains most of the known phosphate reserve and because its geology has been studied more extensively than that of other sections . Deposits of phosphate rock on public land may be leased from the Government under the terms of the Mineral Leasing Act of 1920 , subject to the regulations of the Bureau of Land Management . Public interest in phosphate production is growing , as shown by an increasing number of applications for leases . Two mines are being operated steadily for the production of phosphate rock by companies that have also the necessary processing plants for the manufacture of fertilizer . Total western phosphate - rock production in 1947 is reported by the Economics Statistics and Division of the Federal Bureau of Mines to have been 1,193,000 long tons , mined in Idaho , Montana , and Wyoming . The average grade was 30.7 percent of contained phosphorus pentoxide (P205 ) ; the average value at the mines was $5.67 per long ton . Idaho contributed 905,000 tons , or somewhat more than 75 percent of western production . Western fertilizer plants took 23 percent of total production; 76 percent was exported . Strip mining accounted for 75 percent of the Idaho tonnage; the remainder was stoped from underground workings . Rock must contain a minimum of 30 percent P205 to be commercially useful for the production of superphosphate fertilizer by current acid treatment methods . Research by corporations and Government agencies has been directed toward the use of lower - grade ore . So far , only by smelting can rock containing as little as 25 percent P205 be used economically . Any development of processing or use pattern that would render the mining of , say , 20 percent rock profitable would have important effects in reducing the unit cost of mining . In the search for metallurgical improvements , consideration should be given to the saving of valuable components of the rock, such as vanadium and fluorine , both of which are present in the beds .

Oct 1, 1949

By R. Hogg, S. Chander

"An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example in development of new processes, plant and process design, plant control, problem solving, etc. IntroductionThe behavior of particulate systems, in mineral processing and other applications, is primarily affected by the physical characteristics (size, shape, surface area, pore structure) of the particles and the nature of the different solid-fluid interfaces present. Mineral processing operations in general are either designed to modify and/or control physical and interfacial properties (grinding, classification, agglomeration, etc.) or are strongly influenced by them (flotation, flocculation, solid/liquid separation, etc.). Characterization of physical and interfacial properties should be an integral part of the development of new processes, plant and process design, and routine plant operation.Our purpose in preparing this article has been to present an overview of the current status of characterization, to point out areas of weakness, and to discuss the reliability and limitations of the various techniques, procedures, and instrumentation available. For more detailed discussion of methods, etc., the reader is referred to standard references.Sampling particulate solids.Sampling is a critical factor in any procedure for characterizing particulate materials — the reliability of characterization data is ultimately limited by the extent to which the sample used was truly represen¬tative of the population from which it was taken.Sampling from particulate solids involves two basic problems: (1) the selection of a random', unbiased sample and (2) choice of the appropriate sample size.The problem of sample selection involves the design of a sample collection procedure that ensures that every kind of particle in the population has the proper chance of being included in the sample without bias. Specific procedures such as the well-known cone-and-quarter technique have been developed and are discussed at length in the literature on particle characterization (Allen, 1981: Herdan, 1960: Gy, 1982)."

Jan 1, 1989

By Scott Turner

The monetary metals , gold and silver , have recently been the object of such general interest that the United States Bureau of Mines has received many inquiries regarding them . Though requests for technologic information have been numerous , they have been exceeded in number by those concerned with economic aspects of these metals . The nature of the latter communications indicates that the public is not generally aware that various Bureau publications are available which deal with the economic situation of gold and silver . For this reason , it is deemed advisable to present a brief résumé of the papers which are obtainable from the Bureau or the Superintendent of Documents , together with the text of three articles recently prepared by the Director , reprints of which are not otherwise available . The Bureau of Mines compiles figures showing mine production of gold and silver , by districts and States , and cooperates with the Bureau of the Mint in determining the total annual output in the United States as a whole . 3 It recently established an annual canvass to determine the consumption of silver in the arts and industries of the United States , and published an economic paper covering such use in 1928 and 1929 , followed by an information circular on silver consumption by industry during the 2 years subsequent . A 4-year record is thus provided for those interested in utilization of silver . The Bureau has also published summarizations of all available data upon world production since 1493 of gold and of silver . It has , furthermore , rendered available a compilation of production- data of silver mines of the world , and an analysis of it , showing the proportions of silver and other metals contained in all the ores from which silver is derived . " All of these papers are concerned solely with putting into readily usable form statistical data and other factual material ; they do not offer theories or express opinions upon controversial questions related to these metals . Three other recent papers concerned with gold and silver are presented below in order to put them in shape for distribution by the United States Bureau of Mines . All three of them are by the Director of the Bureau . It should be noted that these papers do not commit

Jul 1, 1933