Search Documents

By Charles B. Carpenter

For many years, studies of ground movement and subsidence accompanying subsurface mining operations have been part of the research program of the Bureau of Mines. Periodic observations by engineers of the Mining Division of the Bureau of man-built structures beneath which mining operations are conducted offer indisputable evidence of subsidence in the form of creeks in masonry structures and fractures and depressions in the surface of the earth. As the removal of subsurface rock and earth material by mining, especially by the room-and-pillar method, is equivalent to withdrawing some of the foundation of a building, subsidence of the formations above, the mining levels in certain areas is easily understood as a gravitational adjustment of the overlying earth formations.

Jan 1, 1940

By C. A. Herbert

Coal-mine explosions in the United States during the past 10 years ranked third among the causes of coal-mine fatalities and constituted 16.1 percent of the total fatalities. In Indiana, however, during this same period the percentage of fatalities from this cause was much higher than the average percentage for the entire country. It is only through knowledge of the factors that have led to these past explosions that intelligent steps may be taken to prevent similar occurrences in the future. Although information concerning many of the earlier explosions is lacking, an attempt has been made to tabulate the information available in the hope that it may be of assistance in calling attention to some of the principal causes of explosions in Indiana.

Jan 1, 1934

By Manuel Gomez

Carbon number distributions were obtained for tar acid fractions from five low-temperature tars by low-ionizing voltage mass spectrometry. Quantitative data for phenols representing seven structural compound types were examined by statistical analysis. It was shown that for the phenols discussed, the data could be represented by regression equations expressing phenolic concentration as a function of the reciprocal of the carbon number and the carbon-to-hydrogen ratio of the parent coal. The total concentration of each structural type present was found to depend on the molecular weight and boiling point of the initial member of the group. Carbon distribution data for the tar acid fractions studied support the view that low-temperature tars contain the same chemical compounds but in different proportions.

Jan 1, 1965

By James H. McCutchan

The small and remote mine operators must comply with the Federal Mine Safety and Health Administration regulation requiring them to train and maintain mine rescue teams. The alternative is for the operators to contract with established teams within two hours travel time of their mine. Many of these remote operations are too far away from established teams and have too few employees to make up the necessary teams. Many cannot comply with the regulation either from a manpower or economic standpoint. The Office of Arizona State Mine Inspector, under the direction of the Honorable James H. McCutchan, State Mine Inspector, entered into a contract with the Bureau of Mines to develop the concept of a volunteer mine rescue program. This program with the assistance of the mining industry and volunteer rescue organizations, has planned and instituted a statewide volunteer mine rescue organization. The trained and equipped volunteers are stationed throughout the state and can respond to a mine emergency within the time constraints.

Jan 1, 1984

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

By P. J. Remington

Field measurements utilizing a seat pad accelerometer were made on 61 surface coal mining machines in order to quantify the vibration levels experienced by the operators. Those data were combined with information on the statistics of the operating times of those machines in order to compare the operator's vibration exposure to the criteria in ISO 2631, ?A Guide for the Evaluation of Human Exposure to Whole Body Vibration.? The comparison showed that about ha]f of all surface coal mining machine operators can be expected to be exposed to vibration exceeding the fatigue decreased proficiency criterion, whereas only on the order of 15% would be expected to experience vibration exceeding the exposure limit. Detailed exposure statistics are presented and the implications of the results are discussed.

Jan 1, 1983

By Richard L. Sayrs

The Eve Mills deposit is in Monroe County, Tenn., near the southeastern corner of the State. The deposit was examined in February 1943 by a Bureau of Mines engineer, and drilling the property was recommended to increase the on: reserves enough to justify mining should war needs require it. The deposits were explored, by 32 diamond-drill holes totaling 11,649 feet during the periods from July 1943 to November 7, 1945, and from April 1944 to August 17, 1944. The drilling campaign disclosed a large area of mineralization. The ore, however, is apparently confined to long, narrow sheets. The indicated grade of the ore bodies blocked cut by the Bureau of Mines is 4.o8 percent zinc and 2.10 percent iron.

Jan 1, 1949

By F. K. OVITZ

In its endeavor to promote a more efficient use of coal the Bureau of Mines, in cooperation with the Illinois State geological survey and the University of Illinois, has undertaken an investigation of the coking of Illinois coals. The investigation was started by collecting from various sources the data regarding experiments already made by others; these data have been compiled and are presented herein. The present methods of using coal seem wasteful. When coal is burned in furnaces for the generation of steam, only the heat gener- ated by the fuel is utilized; possible by-products are not only lost but frequently are the source of the smoke nuisance. The volatile matter containing the tar and heavy hydrocarbon gases is difficult to burn completely in many furnaces, and its decomposition produces black smoke. When coal is coked in a by-product oven, the volatile matter is no longer a nuisance but, on the contrary, is the source of many by-products, including benzol, toluol, gas, tar, ammonia, and cyano- gen, all of which increase the value that may be obtained from coal. The coke that remains after the volatile matter has been driven off is a valuable fuel that can be used for almost all purposes for which bituminous coal can be used, and it is necessary for some metallurgical work. It has about the same heating value as anthracite coal. Because of its cleanness and its burning without smoke, it is well suited for domestic heating and the generation of steam in plants where smokelessness is demanded. The use of coke for these pur- poses would do much to eliminate smoke in cities. The best grades are regarded as essential in many metallurgical processes for reduc- ing ores to their metals. By-product coking in the United States during the past three years has increased greatly. When the ovens now in course of construction are completed, the total capacity of by-product ovens will be more than double what it was in 1913. This increase has led to a search for coals other than those now known to be available for use in by- product ovens. Tests with coals from the southern part of Illinois have indicated that coke from Illinois coal unmixed with other coals can be used for fuel purposes and that coke from mixtures of Illinois coal with low-volatile coking coal might be suitable for some metal- lurgical work. In the tests the yield of ammonia was larger than is obtained from Eastern coal. Evidently the development of methods by which good coke can be made from Illinois coals and the by-products recovered is a matter of high importance. Any investigation that will indicate how, by proper treatment, these coals can be made available to supply the market for coke and gas in the Middle West will increase efficiency in their use, and will aid in conserving the country's supply of high-grade coking coal.

Jan 1, 1917

By George S. Rice, O. P. Hood

The need of protecting mines from the danger of inflow of natural gas from neighboring wells has become more apparent each year since it was found that oil and gas underlie the productive coal measures of Pennsylvania, West Virginia, Ohio, Indiana, Illinois, Kansas, Oklahoma, Colorado, and Wyoming, and, to some extent, the coal measures of other States. The proximity of the known gas and oil areas in the United States to the coal fields and the manner in which the fields overlap in certain States are shown in the map comprising the frontispiece (Pl. I). As the result of many requests received from various sources a conference to consider the protective measures necessary to insure the safety of mining operations in gas and oil fields was called by the Director of the Bureau of Mines to assemble in Pittsburgh, Pa., Feb- ruary 7 and 8, 1913. To this conference were invited a considerable number of gas-well, oil-well, and coal-mine operators within conven- ient distance from Pittsburgh, as well as State geologists and State mine inspectors from a distance. Gas and oil wells are also found near other kinds of mines, such as shale and limestone mines in western Pennsylvania, but these cases are so few that for this and other reasons it was deemed best to con- fine the present inquiry to the consideration of the questions involved in connection with coal mines. It was also not thought advisable to consider the protection of mines from other kinds of bore holes than those for gas and oil, such as coal-prospecting holes, drilled either with churn or diamond drills, or salt wells and artesian wells, because little trouble has been ex- perienced in mining operations from these classes of wells. There- fore the following papers and discussions concern almost entirely the following relations between coal mines and gas and oil wells: (1) Protection of coal mines froin gas and oil wells penetrating -through: (a) Open workings; (b) inaccessible spaces or goaves; (c) pillars, or coal which may be left as pillars. (2) The manner of drilling gas and oil wells passing through workable coal beds so as to provide protection for future mining. The preliminary inquiries of the engineers of the bureau had dis- closed that there was no uniformity in the methods of protecting mines against the leakage of gas from wells, that thousands of wells in coal fields are abandoned yearly without adequate plugging, and without surveys or records being kept to show the location of the holes, from which the casings are generally pulled. According to the State geologist of Pennsylvania, as many as 3,000 wells are being drilled annually in Pennsylvania, 2,000 of these holes being aban- doned within a single year. It is such unplugged, uncharted wells that are the greatest menace in mining. The quantity of gas that the wells produce, although not sufficient to be commercially avail-

Jan 1, 1913

By N. S. Dalal, B. Jafari, V. Vallyathan

Electron spin resonance measurements have now been completed on the decay kinetics of the organic free radicals formed on crushing or grinding of a well characterized anthracite coal. The free radicals exhibit a complex decay pattern for the first few hours after the grinding, and a smooth decay thereafter. Parallel hemolysis studies indicate. a half-life of the decrease in the cytotoxicity of the fresh· dust to be about half-a-day. The cytotoxicity of the freshly-made dust decreases on addition of superoxide dismutase, catalase and sodium benzoate. The hemolysis rate is lower for the dust stored in buffers as compared to air. A chemical model will be presented to accomodate the cytotoxicity and spectroscopic data, and ~heir implicati6ns to pneumoconiosis.

Jan 1, 1988

By J. F. Neill, O&apos

The manganiferous schists occurring in the vicinity of Kings Mountain, North and South Carolina, suggest significant tonnages of potential submarginal ores. Although some reconnaissance work in connection with these deposits has been reported, no recent information has been published. Evaluation of the schists as a possible domestic manganese resource has not always adequately considered the fact that the manganese content occurs quantitatively both as oxide and as the silicate, spessartite. The Bureau of Mines investigation herein reported includes preliminary studies to indicate the extent of manganese oxide mineralization and to deter-mine the amenability of the material to sulfur dioxide leaching. The field reconnaissance studies suggest a resource containing in one area an average of 6.4 percent manganese as oxide. The procurement of depth information was beyond the scope of the investigation.

Jan 1, 1962

By M. G. Zabetakis

This publication describes an investigation conducted by the Federal Bureau of Mines regarding the cause of an explosion of a dephlegmator or fractionating column at the Cities Service Oil Company Refinery, Ponca City, Okla., January 22, 1959. The column was that used with the refinery's No.1 Dubbs Coker. The explosion caused the death of an employee of the refinery and resulted in extensive damage to the refinery and to nearby property. The Bureau's study of the explosion began January 26.

Jan 1, 1960

By H. W. Wainwright

.1. The purification pilot plant and the equipment, solution, and gas cycle used for removing hydrogen sulfide and carbon dioxide are described. 2. As sulfur recovery is necessary in any large Fischer-Tropsch plant, pilot-plant runs were made at 300 p.s.i.g. to study the efficiency of tri-ethanolamine solutions in removing selectively hydrogen sulfide from gases containing varying amounts of carbon dioxide. 3. Aqueous solutions of TEA of 20, 30; 35, and 50 percent were investi¬gated. Data indicate that 30 to 35 percent is the optimum concentration if both selectivity and economy are considered. Slightly better selectivity is obtained with the.20 percent solution, but steam consumption is greater owing to the higher solution rates. Results from our pilot plant runs indicate that a 50 percent solution not only produces an acid gas of lower hydrogen sulfide content but also requires high solution rates to effect hydrogen sulfide purification. 4. Data from 37 runs using TEA are presented in tabular form. In addition, the data are correlated and presented in three sets of curves. By using these curves, it is possible to calculate the compositions of the purified and acid gases for various raw gas mixtures. 5. In cooperation with the Southern Natural Gas Co., investigations were carried out at 300 p.s.i.g. on the simultaneous removal of hydrogen sulfide and carbon dioxide, from gases using various concentrations of diethanolamine. 6. Data from 17 runs employing 20, 30, and 40 percent DEA are reported in both tabular and graphic form. 7. A comparison of the data from one DEA run made at 200 p.s.i.g. with those from the runs operating at 30O p.s.i.g. shows float the absorption capacity of the solution, and, hence, the steam requirements per gallon are about the sage for both pressures. .The only real advantage of the higher pressure is the additional volume of gas that can be treated. 8. The quantity of steam needed to reactivate fouled TEA and DEA solutions increased as the reactivator pressure was increased about 1,0 to 1.1 pounds of steam was required for each gallon of circulating solution when the reactivator was operated at 5 p.s.i.g. 9. A curve is included that shows the effect of the hydrogen sulfide con-centration in a lean 35 percent TEA solution on the hydrogen sulfide content of the purified gas and on steam consumption for reactivation. 10. Both TEA and DEA reduced the organic sulfur content of the raw synthesis gas considerably. Analyses of the lean amine solutions showed a gradual build up of sulfur compounds, indicating that the compounds formed by the amines and organic sulfur do not break down under the ordinary operating conditions of the reactivator. 11. Considerable operating difficulty was encountered in the pilot plant owing to foaming of the amine solutions. Laboratory experiments in which the effectiveness of certain antifoam agents was studied showed Alkaterge C to be most promising for the particular conditions studied.

Jan 1, 1952

By R. M. Santmyers

The pigments, whose colors are due primarily to iron exides and iron hydroxides, comprise a variety of yellow, brown, red, and sometimes black paint-coloring agents, both natural and artificially prepared. The natural pigments in this group include ocher, umber, sienna, mineral paints, paint rock, and mortar colors. When the natural color or tinting power--either in the raw state or after treatment--is too weak, these pigments may be "forti- fied" or strengthened. Ocher, umber, and sienna, rhile often described as "iron oxide pigments," are also known as "earthy" rigments. Inasmuch as the iron content of these pigments is, in general, somewhat lower than that of other iron oxide pigments, the ochers, umbers, siennes, and other brown earth pigments are not discussed in the present paper. In addition to a discussion of natural or artificial pigments whose color is due to the presence of iron oxide in some form, this paper contains data on mortar colors, which are medium or low grade pigments used for tinting mortar, cement, and concrete. A great variety of materials are used for theso purposes, including "blue billy" (residue left from roast- ing pyrite), ground slate and shale, and even culm from coal washeries. Dur- ing the past three years, there has been a definite trend among the producers of iron oxide pigments to push the sales of the better grades of colors for tinting mortars. Due to the amount of low-grade coloring matter that is re- quired to impart a strong color to concrete (in soro cases as high as 15 per cent of pigment is necessary) the strength of the cement may be materially impaired. The addition of some 2 per cent of the higher grades of iron oxide to the concrete mix imparts a brighter and stronger colcr, does not weaken the material, and in the end is not as expensive as the low-grade pigments formerly used. Iron oxide pigments occur in nature in various shades and colors, but the red pigments are the most important and account for the larger part of the total red pigments used.3/ The nomenclature of these red pigments is involved and the names given to them are descriptive of the shade rather than of origin, method of produc- tion or chemical composition. In most cases the red pigments under this class may occur naturally or may be produced by heating hydrous iron oxide pigments such as yellow ocher to a sufficiently high temperature to drive off the water of composition. They may also be prepared by fortifying naturally-occurring pigments with stronger natural or synthetic oxides or with coal-tar dyes (e.g. alizarine lake), Most of the mineral reds derive their color from the presence of ferric oxide (Fe2O3), the mineral hematite. This may be present in relatively small percentages, as in the red slates and shales, or it may constitute as much as 90 per cent or more of the material, as in Spanish red. The principal iron oxide pigments used in the manufacture of paint are discussed in the following pages.

May 1, 1932

Reduce the airborne dust generated in a longwall coal face. Approach Reduce the rotational speed and increase the depth-of-cut of the longwall shearer. How It Works An Anderson-Mavor AM500 double-ended ranging drum shearer was fitted with drums specially designed to accept the large picks required for this testing program. Change gears In the shearer allowed rotational speeds of the drums to be set at 35, 45, 55, or 70 rpm. As deep cutting removes larger coal fragments, the specific energy requirements of the operation are reduced and less surface area results. Dust generation and shearer power consumption are also reduced. The lower rotational speed minimizes the fanning action of the cutterheads and thus reduces the amount of coal fines that become airborne.

Jan 1, 1981

By G. E. Rennick, F. E. Armstrong, J. Pasini, J. R. Abrams

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 112 part per billion. Expand- able cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jul 1, 1972

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By A. J. Kraemer

The twenty-fourth of a series of semiannual surveys pertaining to motor gasoline marketed in the United States was made by the Bureau of Mines in August, 1931, The first part of a report giving the results of that survey as they pertain to specification data is given in this paper. A companion report, Part II, is in preparation and will discuss the results off other determinations made on the samples, including octane number ratings on the individual samples (to be made by the Bureau of Standards) and results of the determination of gravity, color, doctor test, and "gum" content by the copper dish method and the Bureau of Mines steam-oven method. The retail price and the tax at the time Each sample was taken will also be retorted. History of Survey The Bureau of Mines made its first survey of motor gasolines sold throughout the United States in 1915,4 a second in 1917,0 and a third in April, 1919.0 These three surveys showed that during each 2-year interval the motor gasoline had become notably less volatile. In order

Jan 1, 1932

This three-part report provides the results of an industrial engineering study that assessed the safety and efficiency of underground ore handling in U.S. metal mines. One of the primary findings of the study was the improvement needed in controlling muck size in the are handling stream. Oversize ore is causing much additional labor, creating work stoppages, and is a principal cause of accidents in metal mines. The specific objectives of the Present Systems Study were to determine and evaluate the productivity of existing ore handling systems in a representative group of underground metal mines, to relate the available historical accident record statistics of these selected mines to the specific operations in the overall ore handling operations, and to highlight the potential areas of improvement for each mine on the basis of productivity and associated hazardous index for each operation.

Jan 1, 1974

By G. W. Josephson

WHILE methods of utilizing blast-furnace slag have been developing, a great deal of literature on the subject has accumulated, but no comprehensive summary of information that would be helpful to engineers, contractors, architects, chemists, and others in under-standing and more successfully using this byproduct of the iron and steel industry has been published in the English language. The National Slag Association recognized the need for such a publication, and the Problems Committee of the Association under-took in 1943 to accumulate the necessary material. Over a period of several years this committee compiled pertinent information in manuscript form, and in 1948 the Bureau of Mines and the National Slag Association made an agreement whereby the Bureau was to prepare the data for publication as a cooperative bulletin of the Bureau of Mines and the National Slag Association.

Jan 1, 1949