Search Documents

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

By John B. Gayle

The Bureau of Mines has designed and constructed an experimental coke oven, using a commercial oven as a model where practicable. Because the rate of carbonization is important in determining the quality of the coke produced and may affect the "mount of pressure developed during carbonization, particular attention was given to those elements of the design that govern the heat transfer to the charge. The new oven deviates in design from most existing test ovens in that the charge is full width (17 inches), the heating walls ore constructed of 4-1/2-inch silica brick, and zoned, heat-input arrangements compensate for heat losses at the ends, top, and bottom of the charge. This report describes the oven, which was designed by H. S. Auvil and installed under his direction, at the Southern Experiment Station, Tuscaloosa, Ala., while he was supervising, engineer, Coke Section. It gives the results of a limited number of carbonizing tests. These results indicate that the main objective in designing and building this oven, that off duplicating commerical, slot-oven carbonizing conditions, has been accomplished; if coke-discharge conditions simulate commercial-oven conditions, the cokes from the experimental oven arc very similar to oven coke, in soma tests being fully as close is duplicate tests from a Angle batch of coke.

Jan 1, 1952

By James A. Wasson

Because of the danger to life and property in a coal mine if an oil or natural gas well should be accidentally intersected during mining operations, certain precautionary measures should be carried out prior to entering previously unmined areas. The locations of all wells both at the surface and at the depth of the coalbed should be accurately determined. The condition of the well should be learned from surface observations, and more importantly, from subsurface examination by geophysical logging devices where possible. It is also desirable to learn the physical properties of the hydrocarbon-bearing rock formation and the hydrocarbon fluids. The major hazard presented by oil or natural gas wells to mining operations is that of explosion and fire due to the rapid release of gas into the mine atmosphere. Wellbore pressure, the principal index of danger, should be determined by one or more of the methods described and by a service company such as those listed in the appendix. Because of high pressures involved and the consequent hazard, much emphasis has been placed on underground storage of natural gas in areas containing minable coalbeds. Maps are shown of the principal coal producing areas and the locations of currently active gas storage reservoirs. A checklist has been included of factors to be considered when mining coal in an area where oil or gas wells exist.

Jan 1, 1973

By R. E. Peterson

Scrap iron is partially oxidized at elevated temperatures in the selective oxidation process to produce iron oxide and a dense residual metal of high purity. Investigation of the process was confined to converting automobile hulks into useful products. In one test series, compressed, sheared automobile scrap was processed at 1,000° C in a 36-foot-long rotary kiln at feed rates ranging from 300 to 1,200 lb/hr. Less fuel was required to maintain the temperature at the higher feed rates because of the heat generated from the burning of the combustibles and the oxidation of the iron. The bulk density of the residual metal exceeded 75 pounds per cubic foot. In an attempt to lower the quantity of contaminants in the residual metal, another test was designed using automobile hulks which had been prepared by ripping, a low-cost method of scrap fragmentation. Before oxidizing the ripped scrap approximately 62 percent of the total copper was removed in a tumbling, screening, magnetic separation and hand-sorting system. Cast iron made from the residual metal obtained by selective oxidation contained 0.15 percent copper; iron oxide scale obtained from the kiln averaged 0.13 percent copper. Pellets made from the scale demonstrated compressive strengths necessary for blast furnace reduction; lead and zinc were removed by volatilization when the induration was performed in a reducing atmosphere.

Jan 1, 1972

By R. N. Love, L. Goldman

"INTRODUCTION When tannin is present in a boiler water, it causes certain difficulties in many analytical testing procedures because of its colloidal action in interfering with the removal of suspended matter by filtration and also because of the color it imparts to the boiler water.For example, in any test for phosphate in boiler water the first step is to filter out of the sample all sludge and suspended solids. Calcium phosphate in the sludge would give high results if not completely removed. If tannin is present in the sample, the sludge and suspended matter tend to pass through the filter paper so that it is difficult to remove it all. It may even be that tannin makes some of the suspended material in the sample completely nonfilterable. If this is true, it would be necessary to destroy or remove the tannin from the sample before filtering to get complete removal of calcium phosphate from the sample. In addition, if the test used is a colorimetric one, the tannin causes interference by its own color.As the calorimetric phosphate test is so convenient for control purposes and the use of tannin for boiler water treatment has become common, it has become necessary to develop suitable methods for employing the colorimetric phosphate test for boiler waters containing tannin. In this paper three different methods for doing this arc described and studied."

Oct 1, 1946

By T. M. Romslo

"The Keystone and St. George properties are in the so-called Johnson Camp area and adjoin a property that in recent years has become a steady producer of low-to medium-grade copper-zinc ores. The Keystone Copper Co. was active intermittently from 1908 to 1938 and during 1926 to 1937 produced a recorded 1,100 tons of 5 percent copper ore. There is no evidence that ore has been produced from the St. George property.In the Johnson Camp area both igneous and sedimentary rocks ranging in age from pre-Cambrian to Quaternary are exposed. The ore bodies are in the Paleozoic rocks and occur principally in the Abrigo formation, which is composed mainly of limestones and shales. The rocks of the productive zones are metamorphosed and are cut by systems of fractures and faults. Chalcopyrite and sphalerite, the principal ore minerals, replace altered limestones to form deposits locally called mantos and chimneys.Investigation of the Keystone and St. George deposits by the Bureau of Mines included topographical and geological mapping of the surface and the underground workings and diamond drilling from the surface. A total of 10,067.8 feet was drilled in 22 holes. The drilling started November 13, 1947, and was completed August 19, 1948.This report records factual information obtained during the course of the investigation."

Jul 1, 1949

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine was evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, end a previously described5/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive physical and. chemical apparatus. Following the termination of this study of chronic poisoning, possibilities for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel. A microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals with the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By S. J. Pearce

The need for a simple, very sensitive, and accurate method for the determination of benzene in blood and urine vas evident throughout a recent study of chronic benzene (C6H6) poisoning conducted cooperatively by the United States Bureau of Mines, The Barrett Company, and the producers of benzene. A combustion method which will be described in a later publication, and a previously described/ adaptation of Smyth's method were developed and used during that investigation. The adaptation of Smyth's method gave satisfactory results when dealing with exposure conditions that produced chronic poisoning in a comparatively few days, but it was time-consuming; and lacked the accuracy necessary for a study of the absorption, distribution, and fate of benzene in the body during exposure to threshold concentrations of benzene vapor in air. The combustion procedure was satisfactory from the standpoint of sensitivity but was cumbersome, intricate, time-consuming, and required the use of special and somewhat expensive Physical and chemical apparatus. Following the termination of this study of chronic poisoning, possibilities ides for developing better methods occurred, and these have been investigated by the Bureau of Mines with the aid of Relief Works Division personnel microcolorimetric method for the determination of benzene in air has been described recently.6/ The present report deals rich the adaptation of this new colorimetric method to the determination

Jan 1, 1936

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

By Jr. East

The Bureau of Mines conducted an investigation of the Nightingale tungsten deposit about 38 miles north of Fernley, Nev., from September 1939 to March 1940, to determine possible resources of tungsten ore. The property was owned by the Gold, Silver & Tungsten, Inc., which maintained its offices in Boulder, Colo. Ore was discovered in 1917, and some ore was mined in 1918 and treated in a mill at Toulon, a station on the Southern Pacific Railroad, 40 miles east. Same shipments were made since 1918, but no production figures are available. The ore is mined from nearly vertical tactite bodies at the limestone-granite contact. The Bureau of Mines excavated 944 linear feet of trenches, drifted 52 linear feet, sunk a shaft 20 feet in depth, sampled the underground workings by cutting 743 linear feet of channels, sampled the surface trenches by cutting 415 linear feet of channels, and drilled 9 diamond-drill holes, totaling 3,000 feet. The ensuing sections note the location and physical features of the district and specify the property and ownership. The history of the mine is briefed, and the geology and mine workings are described. The work done by the Bureau of Mines is summarized and supplemented in detail by assay maps, logs of diamond-drill holes in appendix A, and a table of sample analyses in appendix B.

Jan 1, 1950

By Don M. Coulter

"INTRODUCTION The Margerum bauxite district, in Colbert County, Ala. was investigated in December 1940 and in February 1943 by R. W. Smith of the Bureau of Mines .3/ A geologist of the Federal Geological Survey investigated and mapped the district in the fall of 1942.These preliminary investigations indicated bauxite showings over an area about a mile long by 2,000 feet wide. It was felt that the chances were good for finding one or more large deposits of low- to medium-grade bauxite. The location - within 35 miles of the alumina plant of the Reynolds Metals Co. atLister Hill, Ala. – made it especially attractive. A field office was established in Iuka, Miss., on May 19, 190,, and mineral agreements were executed with four landowners covering 1,146.6 cores.The drilling on the project was done under contract. The power drilling was supplemented by a labor crew that drilled hand-auger holes, where there was little or no gravel overburden, and sampled the old test pits.The Federal Geological Survey, after thorough study of the district, recommended 54 drill holes 4/ to delimit the known deposits and to search for possible extensions. After the drilling started, many of these locations eliminated, and others were changed upon the basis of information gathered from the holes as they were drilled."

Mar 1, 1948

By Edward A. Barrett, Lynn L. Rethi

Recent studies have shown that miners performing construction, maintenance, and repair (CMR) work activities in the conduct of their jobs incur from 39 to 65 percent of all reported injuries in the mining industry, The number is particularly high at surface aggregate operations; however, the problem exists at all mining locations and commodities. To address this issue, an interactive, (3-D) slides training exercise, Hazard Recognition Training Program for Construction. Maintenance and Repair Activities, was developed. The purpose of the exercise is to teach work& to recognize CMR hazards in the workplace and to deal with them using accepted safe work procedures. It was field tested using a total of 340 persons from surface mining operations in six states. The subjects were tested before and after the training intervention to determine if objectives of the instruction were achieved. Results indicated that 7 1 percent of the participants showed improvement in ink test scores. Following the posttest, subjects responded to a seven question Likert scale. These questions related to the validity of the exercise and the utility of the training program. More than 93 percent of the miners reported that they "learned something new from the training" and over 94% said they "would use these practices to work more safely".

By Michael J. Sapko, Gregory M. Green, Harry C. Verakis, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of U.S. coal mines. The last comprehensive survey of this type was performed in the 1920’s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA’s ten bituminous Coal Mine Health and Safety Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920’s. The significance of these finer coal dust sizes is discussed relevant to the amount of rock dust required to prevent coal dust explosions.

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By Suresh K. Bhatt, Dennis R. Dolinar

The roof bolt system of a mine, if properly selected and installed, can allow for better roof control and reduce the potential for roof falls. Because of this potential to reduce roof falls and improve ground control conditions, the National Institute for Occupational Safety and Health (NIOSH) has an interest in the types of roof bolts that are used by the coal industry. Further, NIOSH has conducted research into how various support parameters can affect the number of roof falls that occur, including support type. Today, the five main types of roof bolts installed in U.S. coal mines are mechanical anchor bolts, point-anchor or resin-assisted mechanical anchor bolts, torque-tension bolts, combination bolts, and fully grouted resin rebar. This paper describes each support in detail. Because of the importance of resin in the functioning of the majority of bolts installed, resin grouts are also discussed. Further, trends in the types of roof bolts used are reviewed. Over the last 10 years, the significant trend has been the large reduction in the relative number of mechanical anchor bolts that are installed. These bolts have been replaced mainly by the resin-grouted rebar system. Data are also presented to show the impact of these changes in bolting on the number of roof falls.

Jan 10, 2000

By D. W. Scott

Thermodynamics is a powerful tool for investigating rotational isomerism in substituted ethanes and related molecules. Accurate calorimetric data can be interpreted to give information, not only about the energy difference between conformations, but also about the shape of the potential barrier hindering rotation from one conformation to another. However, a deterrent to this use of thermodynamics is the labor required to calculate the contributions to the thermodynamic functions for assumed potential functions. Tables of thermo-dynamic contributions for appropriate potential functions can eliminate that labor and greatly facilitate the thermodynamic study of rotational isomerism. In this research, tables of contributions to the thermodynamic functions were compiled for two potential functions typical of some commonly encountered examples of rotational isomerism. TYPES OF POTENTIAL FUNCTIONS Potential function 1, illustrated in figure 1, A, has two equal minima higher than the third. It has the general shape of the barrier to internal rotation in n-butane, for example. The trans conformation of n-butane has the lowest energy, and the two skew or gauche conformations have equal but higher energy. Potential function2, illustrated in figure 1, B, has two equal minima lower than the third. It has the general shape of the barrier in 2-methylbutane, for example. The two C1 conformations of 2-methylbutane have equal energy much lower than the assumed Cs conformation, which has not been observed spectroscopically.

Jan 1, 1962

By Charles L. Kimbell

Following the pattern established in the 1989 edition of this study, the concept of data availability must be addressed, because there are perceptible changes from year to year, and the availability of accurately reported, precisely defined statistics and nonstatistical information provides the only sound basis for analytical studies of any type. As the countries of eastern Europe, including the numerous states that formerly comprised the U.S.S.R., undergo the transition from centrally planned economies' to market economies, there has been a perceptible increase in information availability for rather obvious reasons. Any industrial operation seeing economic assistance from government and/or private sources outside the country in which the facility is sited must provide some appraisal of its operations at the time it seeks assistance, as well as some information on previous performance to serve as tools in evaluating its potential under the proposed development scheme for which it seeks financial assistance. This situation, coupled with governmental recognition that concealment of much of the national mineral production, trade, and consumption data for purposes of national security probably never was really necessary and certainly proved unnecessary with the end of the so-called cold war, has led to the publication of increasing amounts of both statistical and nonstatistical information in the countries undergoing economic transition.

Jan 1, 1993

By O. P. Hood

The spontaneous combustion of coal lies at the bottom of the subject of storage. It is useless to store coal that is to be lost by fire from spontaneous combustion. Every engineer is familiar with the phenomena of the self-heating of coal, yet, for all that, spontaneous combustion is relatively rare. If we counted the times a portion of cod was stored where it would be undisturbed for a few weeks, the number of such storage operations in any one year would mount into the millions. Of these, a relatively small number show the phenomena of spontaneous combustion and time risk per ton is very small. It is extremely rare that in the smaller operations involving; only a few tons there is any heating. There is no spontaneous combustion of anthracite, and very rarely does the domestic consumer of bituminous coal find troublesome heating. The main interest in the subject lies in the large piles needed as reserves for public-service utilities, and the industries. Everyone desires to have directions for storage that are perfectly simple and yet will insure against loss. Unfortunately, the problem is too complicated for a simple solution. Many of the factors involved are difficult to determine, as we have no practical means of quantitative measurement. The factors involve chemistry, physics, and engineering, and the man who is

Jan 1, 1939

By L. R. Burdick

Sulfur compounds have long been recognized as damaging pollutants of the air. A number of investigations have been made to determine the amount of such compounds existing in the air of various cities; moreover, some study has been given to the conditions affecting the concentrations. This paper summarizes published investigation and includes a bibliography on the subject. The methods of obtaining data have differed to the type of sampling, analysis procedure, hour of sampling, number of locations, and number of determinations made. Sampling methods include both the continuous type, covering a day or a number of days, and what can considered the ?snap? type, covering very short periods. Continuous sampling has, given data representing the average concentration at the location chosen but no information regarding variations from hour to hour, are none that might be said to represent the average for a city. The snap-sampling method, while not giving a true average for any one location or area, has in some instances made available date regarding variations of concentration during different hours of the day and at various locations or zones within the area chosen. Although the sulfur compounds in the air nay include sulfur dioxide, sulfur trioxide, hydrogen sulfide, and organic compounds of sulfur, most investigators report on the basis of sulfur dioxide. This gas unites with moisture to form sulfurous acid.

Jan 1, 1939