Search Documents

By C. I. Pierce

The Bureau of Mines conducted laboratory tests to determine if ultrasonic energy could reduce either the residual water or oil content of petroleum reservoir-rock samples from Appalachian area oilfields. Brine-saturated core samples were flooded with oil to residual brine saturation and subjected to 20 kilocycles per second ultrasonic energy. Then they were flooded with brine to residual oil saturation and again subjected to ultrasonic energy. Additional water displaced as a result of the application of ultrasonic energy to the flow system ranged from 0 to 4.3 percent of the original brine and averaged 1.9 percent. The increase in oil recovery as a result of the ultrasonic energy ranged from 0 to 9.0 percent of the original oil and averaged 3.1 percent. On the basis of the tests, it appears that 20-kcps acoustic waves would not have field application for oil recovery.

Jan 1, 1968

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

By R. Karl Zipf

In some instances, extensive room-and-pillar working scan collapse with little warning and pose a serious risk to underground miners. Traditional strength-based pillar design methods applicable to coal or hard-rock mines use a factor of safety defined as pillar strength divided by pillar stress. Factor of stability, defined as local mine stiffness divided by post-failure pillar stiffness, may offer a way to design room-and-pillar mines and eliminate collapses. Three alternative design approaches to decreasing the risk of large-scale catastrophic collapses are described: the containment approach, the prevention approach, and the full-extraction approach. Until good data on the post-failure behavior of pillars become available, the containment and full-extraction options are the safest. The limitations in our ability to evaluate both the stability of old workings and the long-term performance of room-and-pillar mines are described.

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By Tobias W. Goodman, Joseph Cervik

This Bureau of Mines report investigates the horizontal trajectory of boreholes drilled in coalbeds using the rotary drilling technique. Test holes drilled in coalbeds showed that the path of a borehole in the horizontal plane depends on drilling assembly configuration, drill bit rotation, and coalbed geologic features. An assembly that contained an 18-ft (5.53) long drill collar and two centralizers had the best horizontal stability evidenced by trajectories that deviated less than 16 ft (4.9 m) from a target at 1,000 ft (305 m). Removal of one of the centralizers resulted in a loss of control of hole trajectory in the horizontal plane. Generally, holes tended to turn to the right, presumably because of right-hand rotation of the bit. Deviations from the original bearing line were as much as 200 ft (61 m) or more at a depth of 1,000 ft (305 m).

Jan 1, 1988

Provide mine personnel with a convenient means of determining the optimum installation geometry of roof trusses in bedded roof. Background Mine operators frequently ask the following questions concerning roof truss installations: 1. Where should the bearing plates or brackets be placed or where should the inclined holes be started? 2. At what angle should the holes for the inclined chords or angle holts be drilled? 3. What tension should be put into the inclined chords so as to achieve the most effective results for the effort and expense? Truss hardware manufacturers have responded to these questions with answers based on what seems to work best. While designs based on past experience are frequently reliable, there was a need for a rational approach that could accommodate a variety of conditions. The Bureau has developed a procedure that enables mine operators to optimize roof truss installations in bedded roof.

Jan 1, 1989

By M. J. Sapko

The Bureau of Mines conducted laboratory-scale flammability experiments to investigate the possible use of water spray systems for inerting or quenching mine-gas ignitions, such as those encountered at the working face of a coal mine. The inerting results for premixed methane-air-water mixtures indicated that water droplets of less than 10 µm tend to be as effective as the vapor. Water requirements for inerting such mixtures were much smaller than those for quenching the sustained flame propagation by the application of water sprays. The minimum water mass concentration for quenching methane-air flames increased linearly with increasing droplet diameter (surface weighted mean) and decreased with increasing spray temperature, whereas the droplet surface area required per unit volume was essentially constant for a given gas mixture composition. Data extrapolations indicated that a quenching system may be feasible for the longwall mining application.

Jan 1, 1977

By Thomas E. Marshall, Roy H. Grau

The U.S. Bureau of Mines has developed an acoustic test for determining if a rock salt sample is from a "normal" nongassy salt face or from a gassy face where an outburst has the potential to occur. The test is based on the observation that a salt sample taken near an outburst-prone zone produces an audible popping sound when it is dissolved in water. The sound is produced when pressurized gas that is trapped in salt samples is released. In the acoustic test, the sound is electronically measured, digitized, and transmitted to a microcomputer; the output is an average decibel value that classifies the sample as "normal" or "outburst." The acoustic test procedure and equipment are described, and raw test results and data analysis are shown. Results are also shown for several salt samples that were analyzed using a laser Raman microprobe.

Jan 1, 1990

By John Ward Smith

Methods for estimating the amounts of nahcolite, dawsonite, and the sum of these two sodium carbonate minerals from oil-yield assay data are developed and evaluated for Green River Formation oil shales from the saline section of Colorado's Piceance Creek Basin. Derived statistically, these estimation methods depend on the fact that these minerals yield water and gas measured during oil-yield assay. The estimation procedures yield values for nahcolite and nahcolite-plus-dawsonite of sufficient accuracy for stratigraphic plotting and correlation, whereas estimates for dawsonite are more generalized. However, resource estimates and reserve computations for both nahcolite and dawsonite accurate within 10 percent of the real value are readily available by summing the mineral amounts calculated by the procedures presented. These estimation procedures are applicable to oil-yield assay data on core samples from more than 30 coreholes which have penetrated the saline section of the Green River Formation in Colorado.

Jan 1, 1972

By F. N. Kissell

The Bureau of Mines used sulfur hexafluoride (SF6) tracer gas to evaluate the effectiveness of gob ventilation and/or sealing practices at three coal mines, each having different problems associated with their mined-out areas. The purpose of these ventilation studies was to better understand whether current techniques employed for ventilation or sealing are successful at minimizing the potential for gob fires and explosions. The work performed at each mine is discussed: One is a long-wall operation that uses ventilation to carry off hazardous gases, and two are room-and-pillar operations, each with far different concerns, that seal off the gobs to isolate them from the main mine ventilation. In all cases employment of the Bureau's SF6 tracer gas technique resulted in answers to questions raised by the mine operators concerning the effectiveness of their gob ventilation or sealing practices in preventing mine fires.

Jan 1, 1986

By C. D. Litton

The results of full-scale fire tests are used to determine optimum distributions of fire sensors for the protection of conveyor belt haulageways in underground coal mines. Empirical relationships are derived that relate the spacing of fire sensors to the rate of development of the fire hazard. For this application, a critical fire size is defined as that size of fire for which belt ignition and subsequent flame spread down the belt is assured. Detection and alarm, regardless of sensor type or sensing methodology, must be achieved at some point in time before the critical fire size is reached. Based upon this approach, it is found that the horizontal spacing for products-of-combustion sensors is in the range of 300 to 600 meters, while the required thermal sensor spacing is found to be ~4 meters or less. Additional design criteria are discussed for product-of-combustion fire sensing systems.

Jan 1, 1982

By H. W. Kilau

The U.S. Bureau of Mines examined the wettability of bituminous and subbituminous coals before and after exposure to ambient air atmosphere, as part of an ongoing project investigating the coal-wetting abilities of surfactant solutions intended for the suppression of dust during coal mining operations. Exposure periods were generally 7 days or less, and the changes in wetting response were measured with a capillary penetration apparatus. Wetting solutions tested included a nonionic surfactant, two anionic surfactants, and pure distilled water. After exposure, higher ranked bituminous coals treated with nonionic surfactant solution and pure water showed increased wettability, but lower ranked subbituminous coals showed decreased wettability. With the anionic surfactants, the coals demonstrated opposite responses. The wettability changes appeared to be related to the coal moisture content. These changes may be amplified by specific, but incompletely understood, interactions between surfactant polar groups, absorbed water, and the coal surface.

Jan 1, 1989

By Aarne Visnapuu

Experimental modifications have been made by the Bureau of Mines on standard pneumatic rock drills to reduce the noise of the air exhaust, drill steel resonance noise, and noise radiated by the drill body. A close-fitting case and muffler around the drill body, consisting of a metallic honeycomb skeleton filled with viscoelastic absorber on the inside and a durable outer shell, provide both exhaust and drill body noise muffling and absorption. Drill steel resonance noise is reduced by a constrained-layer treatment consisting of a tubular metal cover bonded to the ouside of the rod by a viscoelastic filler. Damping alloy components have been developed to reduce metallic resonance noise. Combined, these modifications have reduced the drilling noise level in granite from 115 dbA to 97 dbA. Data are presented on the individual and combined effects of these modifications on drilling noise and performance.

Jan 1, 1975

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

By M. D. Schlesinger

Experimental data for coal hydrogenation are presented to show that when a vehicle oil produced from coal is present, coal is hydrogenated to the same high conversion whether molybdenum catalyst is impregnated on the coal or intimately mixed with the slurry. Differences in product distribution could be related to the severity of operating conditions. No minimum mixing time was established, but 2 hours was sufficient. Longer periods of mixing, to 14.75 hours, had no effect on the results. The hydrogenation conditions were in the pressure range of 8,500 to 10,000 p,s,i. at 400° to 500° C. Most of the experiments were made in duplicate. The results were obtained with molybdenum concentrations of 0.01, 0.1, and 1 percent. Al the mentioned pressure range and a time at temperature of 15 to 60 minutes, coal conversions higher than 98 percent were obtained.

Jan 1, 1962

By A. Gene Collins

During recent years the interest in trace and minor constituents of oil-field water, petroleum, and their associated reservoir rocks has increased. The metals copper, nickel, lead, manganese, iron, zinc, and cadmium are not determined routinely in oilfield brine analyses. Determination of these metals and subsequent correlation of these data should yield information to aid 1n the interpretation of the origin of different waters. The methods of analyzing oilfield waters have several potential applications: (1) Aiding in the search for petroleum; (2) identifying sources of intrusive brines; (3) controlling corrosion; (4) controlling produced water; increasing knowledge of the geology of subsurface formations; (5) identifying incompatible waters in waterflooding operations; (6) increasing the knowledge of the flow of oil, gas, and water in underground formations; and (7) aiding in the identification and location of valuable mineral reserves. Some brines contain enough valuable minerals to be recovered commercially.

Jan 1, 1962

By John Millhiser, Margaret Bonarek, Dennis McLaughlin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine's Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested and demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

By R. C. Corey

Anticipating the need for convenient, economical, and safe means for disposing of combustible wastes contaminated with low-level activity, in connection with private and institutional uses of radioisotopes, the Atomic Energy Commission (AEC) has provided the Bureau of Mines with funds to develop an incinerator for this purpose. A prototype incinerator, designated hereafter as BOMAEC-30, was designed, constructed, and tested, based on fundamental and applied research investigations of the combustion characteristics of rubbish and sawdust, which will comprise the bulk of contaminated wastes. No radioisotopes were used in the tests; the objective was to remove as much particulate matter from the products of combustion as possible. The prototype unit was designed to burn 30 pounds per hour, using 100 percent over fire air admitted tangentially in an all-metal, cylindrical combustion chamber. The gas-cleaning system consisted of special fabric bags and absolute filters.

Jan 1, 1962

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

By John A. Johnson

For the purpose of comparing the amounts of dust produced by various mining operations, samples of atmospheric dust were collected during a complete cycle of drilling, blasting and mucking at or near the face of the Bureau's Mount Weather testing adit while the efficiency of several types of stemming in metal-mine blasting was being investigated. ACKNOWLEDGMENTS All gas samples were analyzed in the laboratory of the Bureau of Mines Gas Section at Pittsburgh, Pa.

Jan 1, 1939