Search Documents

By Kenneth H. Johnston

Information on oil and water production, volume of water injected, core analyses, and well completion data was collected on 28 Red Fork sand water-flood projects for comparison and evaluation of results. An average water injection efficiency of 35 percent, an average water-injected to oil-produced ratio of 16.8:1, and an average loss outside the flood pattern of approximately 45 percent of the injected fluid resulted in an oil recovery to January 1, 1969, of only 5.6 percent of the pore volume, or 9.1 percent of the initial stock-tank oil in place. The principal causes of poor oil recovery from these projects are the losses of large quantities of injection water from the flood patterns through oriented, natural fracture systems or zones of high permeability and excessive channeling of injection fluids from input wells to oil wells. For more efficient operation and a higher percentage of oil recovery from the Red Fork sand and other low-permeability-sand waterflood projects, directional orientation of both induced-and natural-fracture systems should be determined during early development. The success of a low-permeability-sand waterflood project depends to a large extent upon the orientation of the injection wells with the fracture system.

Jan 1, 1970

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By F. R. Cattoir

This report presents the results of preliminary studies for the evaluation of some fused-salt electrolytes for refining tungsten metal, and describes the equipment used. Some impurities could be eliminated with electrolytes composed of sodium chloride, sodium iodide, or sodium tetraborate in combination with tungstic oxide or sodium tungstate. Electrolytes composed entirely of chlorides were unusable because of the volatility of tungsten chloride. Refining 96-to 98-percent tungsten to produce a commercial grade was more successful than further refining of 99.9-percent tungsten. No electrolyte tested yielded a product pure in all respects. Electrolyte temperatures of about 900° C were necessary to maintain a good dissolution rate at the anode and acceptable cell operation. Cathode current densities at the beginning of a deposition cycle were limited to approximately 1 ampere per square inch. Higher current densities resulted in a finely divided product that frequently failed to adhere to the cathode. The most conspicuous impurities in the tungsten produced were carbon, iron, and molybdenum; the former two came from the iron cell and the graphite cell liner. Electrolytes com-posed of tungstic oxide or sodium tungstate in sodium iodide, or 2Na, 0.B203, were capable of producing tungsten carbide.

Jan 1, 1963

By James A. West

The South Asian countries of India, Pakistan, Afghanistan, Ceylon, Nepal, Bhutan, and Sikkim arc to varying-degrees just beginning to achieve significant economic and industrial development. These countries are richly endowed with certain mineral resources, and development of these resources is being accelerated. In 1965, the mineral industry remained a relatively small sector of the region's economy, accounting for only about 1 percent of its estimated gross national product of $62,528 million. Nevertheless, the estimated $630 million total value of minerals produced in South Asia during 1965 represented an increase of nearly 15 percent t over that of 1964. India continued as the dominant mineral producer of the region, accounting for 85 percent of the total value of all minerals produced ill 1965. India increased its output of iron ore, manganese, mica, coal, and petroleum. Pakistan accounted for 13 percent of the value of the region's output and recorded increased output of iron ore, chromite, coal, natural gas, and most other minerals. The small mineral industry of Ceylon attained remarkable growth in the production of ilmenite, graphite, and gem stones. The mineral industry of Afghanistan remained relatively insignificant, although development of large known resources of natural gas was continued, Nepal, Bhutan, and Sikkim produced no commercially significant quantities of minerals in 1965.

Jan 1, 1967

By Michael G. Zabetakis

Vaporization of a solvent into an airstream at temperatures above the flash point of the solvent is hazardous if vapor is liberated at a rate that is sufficient to produce a flammable mixture. In may operations, the formation of such a mixture is prevented by rapid diluton of the vapors with air. The minimum air requirements for the dilution process are determined by the composition of the lower limit mixture at the temperature and pressure of interest. Because limits of flammability cannot always be calculated with sufficient accuracy for a proposed operation, they .rust often be determined experimentally. The present Bureau of Mines investigation was prompted by an application in which the lower limits of flammability of a number of solvent mixtures were required over a range of temperatures at atmospheric pressure. These limits were to be used along with available solvent-vaporization-rate data to establish minimum airflow rates needed to prevent the formation of flammable mixtures in an industrial process. Lower limits of flammability were determined for a number of mixtures containing methyl ethyl ketone, tetrahydrofuran, toluene, ethyl alcohol, and ethyl acetate in dry air-at atmospheric pressure and temperatures between 16° and 200° C. The experimental values were found to be in good agreement at with those predicted by Le Chatelier's law; variations with temperature were in fair agreement with those predicted by a modified Burgess-Wheeler law.

Jan 1, 1962

By Anthony E. Szczuka

The purpose of this design note is to document the data that has been received from manufacturers, coal companies, training centers, government agencies, etc., that pertains to the completion of the Concept Feasibility Study For Training Equipment Designed to Improve Coal Productivity. Revision A documents additional data that has been received. ACKNOWLEDGEMENTS We wish to express our appreciation to the companies, mines, government agencies, unions, and contractor agencies listed herein that furnished the documented data. In most cases, it was furnished willingly and free of charge. In the few cases where the data was purchased, MDEC IRAD funds were used.

Jan 1, 1976

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976

By Jon C. Volkwein

The U.S. Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low-profile mining machine. Tests were conducted in a full-scale model mine using a continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters tested included mining position, depth of cut, brattice setback, and combinations of scrubber, and directional or symmetrical sprays. Results indicated that either water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 20-ft blowing curtain without sprays. No FVE values were less than the standard 20-ft blowing results.

Jan 1, 1989

By R. R. Sayers

"According to the dictionary,3 an accident is an event that takes place without one's foresight or expectation, often an undesigned, sudden, and unforeseen occurrence of an afflictive or unfortunate character. However, actual experience with accidents, the second most important cause of death in the United States,4 and a more extensive and scientific inventigation of their causes indicate that from 75 to 90 per cent of accidents are avoidable.5 This is borne out by the results of a three-year study of the accident records of 64,000 motor vehicle operators in New York6 which show that certain drivers are prone to accidents, that accident experience is traceable to certain causes, and that accidents don't just ""happen,"" It is estimated that 97,000 persons were killed by accidents in the United States in 1929 and 15,000,000 were injured. Of these about 23,000 deaths were due to so-called industrial accidents. In a list of accident rates by industries, compiled by the National Safety Council7 from reports of member establishments, mining heads the list, in both frequency (74.43 per 1,000,000 man-hours worked) and severity (9.9 days lost per 1,000 man-hours worked). These figures are very much higher than for any other industry; theindustries showing figures most comparable to mining are meat packing with a frequency rate of 55.94 and a severity rate of 1.47, construction with a frequency rate of 50.41 and a severity rate of 4.62, and refrigeration with a frequency rate of 43.35 and a severity rate of 3.04.While there is no way to determine the actual cost of all accidents from a monetary standpoint, estimates indicate that the cost will run into hundreds of millions of dollars annually.Cost of accidents in metal mines.- The United States Bureau of Mines obtains accurate figures on the number of lost-time nonfatal accidents as well as fatal accidents in the metal-mining industry.8 In 1926 the metal mines employed 127,823 men; 430 men were killed and 30,350 men received lost-time but nonfatal injuries as a result of accidents. Each of these fatal and nonfatal injuries averaged 114 days lost time, computing a fatality as 6,000 days lost time. This is equivalent to 3,523,944 days time lost due to accident, or at $5 per day per man, to a wage loss of $17,619,720. Deducting one-ninth of this figure for compensation paid, the metal miner loses in wage annually about $15,700,000, or about $122 per individual. This average loss per individual includes the cost of fatal accidents reckoned at 6,000 days or $30,000, but even if the loss in time due to fatal accidents be deducted, the average cost to each individual metal miner each year for nonfatal accidents is about $32. Estimating the loss to the metal-mine employer as about the same as that to the employee, the annual cost of metal-mine accidents to the employer is about $15,700,000 and to the employer and miner is $31,400,000."

Oct 1, 1930

By R. C. Corey

GERMANIUM is an element that has come into widespread use in the electronics industry in recent, years. So far this increasing demand has been, met by ample supply: however, the future balance is uncertain, and the need has been recognized to discover additional domestic sources of germanium. This investigation was conducted to study the possibility of obtaining a potential supply of germanium from coal or coal ash. It has been known for some time that coal contains germanium; the discovery that By ash from coal-fired boilers often contains appreciably more germanium than the original coal suggested the possibility that coal ash might be an abundant and economical source of this element. In this study the concentration of germanium was determined in numerous samples of coal and ash. A number of miscellaneous waste materials also were examined in the course of the investigation; the results are reported as a matter of general interest. The methods and equipment employed are discussed in detail. Sample-preparation and analytical techniques are described in the appendix. Spectrographic analyses were made on a total of 639 samples, including coal, coal ash, slap ash from lignite and peat, wood ash, and various inorganic materials. Qualitative analyses were run on all samples, and quantitative determinations were made on those samples that contained enough germanium to be measured by this method The lower limit at which germanium can be determined quantitatively by spectrographic analysis is 50 parts per million (p. p. m.), but concentrations of less than 20 p. p. m. can be detected qualitatively.

Jan 1, 1959

By C. Özgen Karacan

Gamma ray, density, sonic and core logs obtained from two boreholes drilled over a longwall panel in Southwestern (SW) Pennsylvania were analyzed for formation boundaries, log-derived porosities and densities and for rock elastic properties from sonic transit times. Gamma ray (GR) and density logs (DL) were analyzed using univariate statistical techniques and fractal statistics for similarity and ordering of the log data in depth. A Fourier transformation with low-pass filter was used as a noise elimination (filtering) technique from the original logs. Filtered data was tested using basic univariate and fractal statistics, rescaled range (R/S) and power spectrum (PS) analysis to compare the information characteristics of the filtered logs with the original data. The randomness of log data in depth was analyzed for fractional Gaussian noise (fGn) or fractional Brownian motion (fBm) character. A new prediction technique using radial basis function (RBF) networks was developed to calculate shear and Young?s moduli of the formations when sonic logs are not available. For this approach, the filtered logs were used as input to an RBF based upon a combination of supervised and unsupervised learning. The network was trained and tested using rock elastic properties calculated from the sonic log of one of the boreholes. The network was used to predict the elastic and shear moduli of the coal-measure rocks over a longwall coal mine in SW Pennsylvania. This approach demonstrated that it could be used for prediction of elastic and shear moduli of coal-measure rocks with reasonable accuracy.

Jan 1, 2009

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and, (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke. This is the third of a series of reports giving results of studies by counties under part (1) of the investigation. This report covers Pike County, Ky., which comprises parts of the Harold, Williamson, Matewan, Gilbert, Pikeville, Regina, Hurley, Pound, and Clintwood quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale of 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1951

By J. E. Matta

The Bureau of Mines has developed a tracer gas method for measuring leak-age through permanent mine stoppings. In this method, a temporary brattice is erected in the same entry as the leaking permanent stopping. Leakage was evaluated from concentration measurements of a tracer gas introduced into the space between the stopping and brattice. Stopping leakages ranging from 15 cfm to 265 cfm were simulated in an underground coal mine. Leakage values determined by the new method were within 10 pct of the known values.

Jan 1, 1978

By D. E. Shanks

As part of its goal to help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is investigating a fused-salt electrolytic procedure for producing zinc metal. A previous report described preliminary, small-scale work on the fused-salt electrolysis of ZnC12. The present report covers a more detailed investigation of the properties of ZnC12-alkali metal chloride electrolyte systems in relation to the production of zinc metal and also discusses electrolysis in largescale, internally heated cells. The effect of composition on bath stability, current efficiency, cell voltage, and liquidus temperature was determined for the ZnCla-NaC1-KC1, ZnC12-NaC1-LiC1, and ZnC12-KC1-LiC1 electrolyte systems. An electrolyte com-posed of 38 mole-pct ZnC12, 31 mole-pct NaC1, and 31 mole-pct KC1 gave the best overall results. Sludge (ZnO) formation in the ZnC12-NaC1-KC1, ZnC12-KC1-LiC1, and ZnC12-KC1 systems was investigated during prolonged electrolysis. The ZnC12-KC1-NaC1 electrolyte showed the least sludge formation. A 1,500-amp cell was operated using the ZnC12-NaC1-KC1 electrolyte at 500° C. Zinc metal was produced at the rate of 4.0 lb/hr with a current efficiency of 95 pct.

Jan 1, 1979

By M. A. Lucas

The Bureau of Mines has developed a computerized mathematical model to predict the distribution of accessory elements throughout a metallurgical process. The model can be used to determine process conditions that effect better accessory element control consistent with continued high primary metal recovery. The model presented is specific for determining the bismuth distribution in lead smelting but can be adapted to most extractive metallurgical processes. Thermodynamic, kinetic, and process parameters form the base for the model. Its logic and structure are described in detail.

Jan 1, 1983

By W. L. Anderson

Standard tellurium analytical procedures were modified to obtain the greater sensitivity needed to support a survey of tellurium resources by the Bureau of Mines. Resulting volumetric and spectrophotometric methods for determining tellurium in all types of tellurium-containing materials are described. Sample decomposition and preliminary separations of interfering selenium, gold, and silver are the same in both procedures. The volumetric method is applicable to samples containing a minimum of 10 parts per million of tellurium, In this method the tellurium is reduced to elemental form, and the colloidal suspension is titrated with 0.01 normal iodine solution. The weight of sample for analysis, from 0.25 to 10 grams, should be selected so that the sample contains 0.1 to 5 milligrams of tellurium. To insure accuracy, duplicate samples should be run and the results averaged, particularly on samples of low tellurium content: The limit of determination is 0,001 percent tellurium, which is equivalent to 0.1 milligram of tellurium when using a 10-gram sample. The spectrophotometric method is particularly applicable to low-tenor materials containing from 0.5 to 50 parts per million of tellurium. Up to 10 gram samples are required for making accurate determinations in the low-concentration range. The sample used should contain between 5 and 100 micrograms of tellurium. The turbidity of a colloidal suspension of tellurium prepared from such a sample is determined in a spectrophotometer .t at a. wave-length of 440 millimicrons, and this value is compared with those of standard samples containing known amounts of tellurium.

Jan 1, 1963

Since roof falls in the vicinity of the working face in underground coal mines are a major source of fatalities and injuries in this country's coal mines, it is evident that the present systems of temporary support for use in this working area are ineffective. This seems to be chiefly due to the inconvenience of setting up heavy and awkward devices such as jacks, posts and the like, which also interfere with the movement of men and machines in this critical working area. This program was concerned with defining and testing commercially available materials that could be used as support elements in a more convenient flexible personnel shield. The objectives of this program were to: 1. survey the materials that might provide the support elements of a flexible-material personnel shield for use in underground coal mines and prepare a list of those materials which appear most suitable for use in coal mines. 2. prepare a proposed testing plan for the materials to be selected from the aforementioned list by the Bureau of Mines for further evaluation. The test plan was designed to provide the following information: a. Tensile strength. b. Proportional limit. c. Creep characteristics at room temperature. d. Elastic properties depicted by stress-strain curves. Properties were tested in two directions for woven fabrics. e. Density. f. Resistance to abrasion. g. Resistance to attack by mine atomsphere. h. Resistance to humidity. i. Impact characteristics.

Jan 1, 1972

By Daryl E. Radcliffe

Ninety-seven roof bolts were instrumented with strain gages and resin-grouted in three areas of the Bear coal mine, Somerset, Colo., by the Bureau of Mines. Measurements taken with these instruments indicate roof support is achieved through a combination of point suspension and resistance to vertical and horizontal stresses caused by localized shearing in the roof. The localized shearing results in bending of the bolts, yielding due to high vertical stresses, and the transfer of high loads to the bolt head or plate.

Jan 1, 1980

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

Apply state-of-the-art monitoring and computer systems technology to remotely monitor geostructural data and evaluate ground conditions in near real-time. Background Recently, the coal mining industry has progressed dramatically from a labor-intensive industry to highly mechanized and automated systems achieving significantly higher production rates. In underground longwall coal mines, production and face advance rates have increased by almost tenfold in the last 15 to 20 years. With increasingly high advance rates, geologic anomalies which affect rock mass quality are encountered more frequently, far exceeding the current rate at which ground control information can be processed and analyzed. As a result, mine operators find themselves with insufficient time or resources to cope with the rapidly changing ground conditions. To keep up with the technological advancement in mining and the associated ground control problems, the Bureau of Mines is conducting a multi-phase research pro¬gram to implement a computer-assisted Ground Control Management System (GCMS). Research is ongoing at present, but when completed the system will be designed to 1) monitor and evaluate data on rock properties, geologic conditions, and rock mechanics data from underground sensors in near real-time; 2) interpret the analyses to evaluate the interaction between various critical ground control parameters; 3) assess the structural integrity of the mine; and 4) determine failure modes and provide recommendations for control measures, design modifica¬tions, and alternative support procedures. The system will be expanded into its full capability during various phases of this research program.

Jan 1, 1991