Search Documents

Identify specific sources and the relative levels of contribution of various components of longwall shearer operations to the total airborne respirable dust generated during mining. Approach A research investigation was conducted in two phases by the Bureau of Mines at five mine sites to identify specific dust sources and their relative importance during long-wall shearing operations. During phase I of the project the specific longwall mining elements identified for evaluation were: cutting, sumping, tramming, conveying, and moving roof supports. During phase II of the project, two dust sources were evaluated: clearance ring cutters cutting in six-inch web width increments, and loading operations. Investigation Results As a result of dust measurements, the gage cutters were determined to be the major dust-generating source on the shearer. These cutters, at 6-inch web depth, produce three times as much dust per unit volume as is produced at 30 inches full web depth. The following list of averaged values for the mines tested shows that shearer cutting generated averaged dust levels four times as high as those generated by conveying, and approximately five times as high as those generated in moving roof supports.

Jan 1, 1984

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By K. O. Bennington

The thermodynamic properties of pollucite [(Cs0.650Na0.185Rb0.028)(AlSi2) (05.8630H0.137)?0.19H201 were determined by the Bureau of Mines in collaboration with the Argonne National Laboratory. The standard enthalpy of formation determined by hydrofluoric acid calorimetry is ?Hf°298 = -3,098.52 ±3.63 kJ mol-1. The standard enthalpy of formation from the oxides is ?H298 (from oxides) = -209.50 ±2.38 kJ mol-1. Low-temperature heat capacities were determined by adiabatic calorimetry from 5.0 to 306.1 K. The derived standard entropy is S°298 = 207.24 ±0.43 J mol-1k-1. Enthalpy increments above 300 K were measured by copper-block drop calorimetry from 349 to 674 K. Various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation and Gibbs energies of formation are given as functions of temperature. The Gibbs energy of formation is ?Gf°298 = -2,919.9 W mol-1

Jan 1, 1983

By Elaine T. Cullen, Albert H. Fein

Federal law mandates that all miners receive safety and health training when first entering the mining industry and at least 8 hours annually thereafter. Although the mining industry has historically relied on an experiential master-apprentice model for training new employees, the formal safety training provided to miners is generally done in a classroom, with mixed results. In a series of stakeholder meetings held by NIOSH across the West in 1997-2000, trainers identified significant gaps in materials that were available to teach new and experienced miners. They asked whether NIOSH could develop effective materials to fill these perceived gaps, as well as make training more effective for those who were required to attend, but who often refused to be attentive. Adult learning theories, social learning theories, mentoring, and storytelling were all employed in the development of a series of safety training videos that have become very popular in the mining industry. This Report of Investigations describes the theoretical frameworks that were used, the process that was developed to produce the videos, and the results of the evaluations as to whether or not they were effective in training new and experienced miners.

Jan 8, 2005

By John J. Henn

An evaluation is presented for an ammonium sulfate leaching process designed to extract manganese from Cuyuna, Minn., and Aroostook, Maine, deposits. In this process the manganese and iron in the ore are reduced to MnO and Fe 3 0 4 in a shaft furnace; the reduced ore is then leached with ammonium sulfate solution forming soluble manganous sulfate while leaving most of the iron undissolved. After filtration, the manganese and some impurities are precipitated from solution as carbonates which are then pelletized and calcined to form a product composed mainly of Mn3O4. The plants are designed to produce 100 tons per day of manganese contained in a product that is suitable for the production of ferromanganese. A byproduct credit, together with the extra processing cost, is included for the Cuyuna ore processing plants because Fe2O3 may be recovered for use in blast furnaces. The estimated operating costs per ton of manganese, excluding income taxes and return on investment, are: [ ] The process with or without byproduct recovery, when treating Cuyuna or Aroostook ores, is not economically competitive with ores available at $71.43 per ton of contained manganese.

Jan 1, 1968

By Robert K. Koch

Laboratory-scale studies on defluorination of natural and synthetic fluorspars by pyrohydrolysis at 1,500° C. were made to determine the feasibility of developing a process for producing hydrogen fluoride from siliceous fluorspars. It was found that the reaction (at 1,500° C.) is not promising for process development, even though a silica-free offgas can be generated. The primary difficulty is the low hydrogen fluoride content of the offgases; an HF content of 6 percent was the best achieved. Previous research by the Bureau of Mines has demonstrated that offgases averaging 27 percent hydrogen fluoride can be produced under carefully controlled conditions at 1,280° C. The lower temperature process is a better method for production of HF. However, charges in which the CaF to Si02 mole ratio varied from 0.4 to 2 could be processed with similar results. Also, combined alumina and ferric oxide contents up to 25 mole-percent did not noticeably alter the rate of defluorination. Therefore, virtually any natural siliceous fluorspar would respond in essentially the same manner when exposed to water vapor at 1,500° C.

Jan 1, 1962

By Donald W. Mitchell

The fire hazard of neoprene, polyvinyl chloride, and rubber conveyor belts was studied at the Federal Bureau of Mines Experimental Coal Mine. The effects of intensity of ignition source, velocity of the ventilating air, and type of belt were investigated at three levels in small-scale gallery experiments. Studies were made in the mine on the effects on ignition and flame propagation of belt-entry dimensions, belt widths, and belt configuration. Methods for extinguishing belt fires were also investigated under simulated mining conditions, and during these trials coal dust and grease were placed on the belt. The research showed that conveyor belts will burn. Neoprene, polyvinyl chloride, and rubber belts, with and without carcass, ignited and propagated flame. The highest rate of flame propagation was obtained on rubber belt. The fire hazard increased with increase in intensity of ignition source and air velocity. Flame propagated only when air was forced through the test zone; propagation was not obtained when forced ventilation was not used, as would exist in a neutral entry in a mine. Automatic water sprays and high-expansion foam effectively arrested flame propagation; direct application of water and bicarbonate dusts was ineffective.

Jan 1, 1967

By R. V. Ramani

In this report, the application and limitation of the various equipment available for surface coal mining are discussed. The correction factors for adjusting equipment performance arising from machine design, material characteristics, and modes of operation are presented. Engineering design, pit layout and equipment selection are discussed with mathematical derivations. Two computer programs (SMCALC and SMRES) have been written to aid in pit design and equipment selection. The Strip Mine Calculation Program (SMCALC) can be used to select the bucket size and reach of shovels and draglines for various pit widths. It will also calculate the number of drills, loading shovels, trucks and bulldozers needed to achieve a production target. The Surface Mine Reclamation Equipment Selector (SMRES) can be used to select the number of bulldozers, scrapers and front-end loaders needed to achieve the desired production.

Jan 1, 1976

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau's existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By R. J. Fantel

To determine the availability of phosphate rock from domestic re- sources, the Bureau of Mines evaluated the potential production of phosphate rock from the demonstrated resources of 130 mines and deposits. The evaluation included an estimation of resources, engineering methods, and capital and operating costs, and an economic analysis to determine each operation's average total cost of production over the life of the mine, including a 15-pct discounted-cash-flow rate of return on all investments. Quantified but not evaluated in this report are substantial phosphate resources at the inferred and hypothetical resource levels. The 130 mines and deposits contain 6.4 billion tons of recoverable phosphate rock product, about 20 pct from producing mines. At total production costs of under $30 per ton in January 1981 dollars, about 1.3 billion tons of phosphate rock product is potentially available, over 90 pct from producing mines. This study suggests that production from low- cost, high-grade phosphate mines now in operation will decline during the next decade, and new higher cost, Lower grade mines will have to be developed to satisfy demand into the next century, In addition to the demonstrated resources evaluated in this study, 7 billion tons of inferred-level and 24 billion tans of hypothetical- level phosphate rock are potentially recoverable, which, in part, includes material containing high amounts of magnesium, Much of this material could likely become available in the near future.

Jan 1, 1983

By Roy H. Grau, John C. LaScola

"This Bureau of Mines report contains a tabulation of methane emissions during 1980 for all coal mines located in the United States with emissions greater than 0.1 MMcfd. Listed for each mine are methane emission quantity, location, and coalbed. The report also compares records of 1975 and 1980 and describes relationships between emissions in 1980 and the Bureau's coalbed gas content data on 11 mines.INTRODUCTIONMethane gas is a threat to safety in underground coal mines. Research by Government and industry has led to great gains in reducing methane gas ignitions and explosions. The development of advanced methane control techniques is necessary for the safe operation of more gassy mines and the implementation of rapid mining techniques.As part of this research, the Bureau of Mines has surveyed total methane emission data from underground bituminous coal mines in the United States and tabulated emissions from mines producing over 0.1 MMcfd of methane. This report is an update of similar studies previously described in Information Circulars 8733, 8659, and 8558 (2-4).3The data from 1980 were compiled from Mine Safety and Health Administration (MSHA) records of air quality-quantity inspections made quarterly at each mine. The inspections involve measuring airflow and collecting air samples in the main returns. From these data, an average methane emission is calculated and used to represent the daily mine emission for each quarter. The methane emissions given in this report are the averages of the four 1980 quarters and do not include mine emissions from other sources such as degasification projects. Since a previous Bureau study showed that emissions from mines emitting less than 0.1 MMcfd represented only 2 pct of all emissions, 0.1 MMcfd was chosen as a lower limit for data collection (4)."

Jan 1, 1982

The Pittsburgh (Pa.) and Spokane (Wash.) Research Laboratories are among the world?s foremost mining research establishments. Once a part of the former U.S. Bureau of Mines (USBM), which was abolished by the U.S. Congress in fiscal year 96, health and safety research at these laboratories was transferred to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is the Federal agency responsible for conducting research and making recommendations for the prevention of work-related illness and injury. The Institute is part of the Centers for Disease Control and Prevention within the U.S. Department of Health and Human Services. Over the past two decades, the Pittsburgh and Spokane Research Laboratories have produced sustained technological achievements in mining health and safety, including? ? Development of novel respirable coal dust control technologies and more effective monitoring techniques to reduce worker exposure to hazardous mine dusts. ? Improved ground control technologies to warn and protect miners from the dangers of coal mine roof collapses and other hazardous strata conditions. ? Improved ergonomic design criteria and training methods to protect mine workers from injuries and fatalities associated with equipment and manual tasks. ? Development of enabling technologies that allow miners to control their mining equipment from a physically safe, protected work area away from respirable dust, harmful noise levels, and roof collapses. ? Improved mine fire detection and extinguishment techniques. ? Development of smaller, lighter, and safer emergency breathing devices.

Jan 1, 2007

By James J. Scott

Workshops were held in eight states during the period from December 12. 1975. through June 25, 1976, under U. S. Bureau of Mines Contract to the University of Missouri-Rolla. The workshops were designed to help define the Bureau's research and development priorities. At each workshop a summary of the current Bureau mine reclamation research was presented which was followed by identification of problems associated with mine land reclamation in the state where the meeting was being held. Discussions included the seriousness of problems locally and how the Bureau could best undertake research to assist the state in solving the problems identified. Participants included representatives of state agencies, educational institutions, and companies involved in surface mining. Attendance at these workshops totaled 201 persons who displayed a wide variety of opinions and ideas as to what should be done In government research and development efforts. A breakdown of these attendees is as follows: 91 state and Federal employees; 69 mine operators, equipment manufacturers and consultants; 33 educators and researchers; and 8 others representing such varied interests as environmental and conservation groups, news media and students .

Jan 1, 1976

Lignite constitutes approximately 97 percent of the near-surface coal resources in Texas. The most significant bituminous resources are in the north-central and southern parts of the state. Coal reserves in Texas are estimated to be 13.7 billion tons, about three percent of U.S. coal reserves. The average thickness of coal seams mined in Texas is approximately eight feet. Texas gained primacy when its regulatory program was conditionally approved February 16, 1980; the program was fully approved June 18,1980. The state's Abandoned Mine Lands program was approved June 23,1980.

Jan 1, 1992

Water pollution has been an integral part of most mining operations in the past. Most mine planners had designed their mining operations with little or no regard for prevention of water pollution. The main planning element was always the economics of mineral recovery. Quite often the cheapest means of mineral recovery resulted in the largest water pollution problems. Recent water pollution laws have introduced a new economic element - water pollution control costs - to be considered in mine planning. Water pollution control costs can be extremely high. Foresighted planning can minimize these costs and provide better water pollution control. Effective pollution control preplanning can eliminate pollution from active mines and minimize pollution that may occur after completion of mining. Presently available technology can practically eliminate water pollution by treatment of the mine water. Use of water treatment during mining has no effect on the levels of water pollution after treatment ceases and the mine is abandoned. Therefore, this section of the report deals with preplanning to reduce water pollution, both present and future, by using at-source control techniques. Proper planning of mining and pollution control techniques should follow the concept of a complete, comprehensive reclamation plan. This plan should have control measures designed for all phases of mining from initiation through completion. Preplanning involves acquiring complete information concerning the future mine site, defining the reasons why mining could cause pollution from the site, and determination of available techniques to prevent or minimize formation or transportation of pollutants. Location of haulage and access roads and other mine related facilities should be included in preplanning for water pollution control. Mine site planning is the primary step in establishing any new mining area and is the key to a successful, non-polluting and economical

Jan 1, 1973

Introduction MINING IS THE BRANCH OF INDUSTRY involving the exploration and removal of minerals from the earth (figure 1). Mining is one of the oldest and most important endeavors of humankind, because it provides the raw ingredients for most of the material world around us and, like agriculture, is the lifeblood of civilization. The main objective of any type of mining is to remove the valuable material economically and safely with minimum damage to the surrounding environment. The Earth has many natural resources on which we depend that must be mined. Coal, oil, gas, and other mineral fuels are used for heating electricity, and numerous industrial processes. Nonfuel minerals such as iron ore, precious metals, and industrial metals, and nonmetallic materials like sodium and potassium are used in chemical and agricultural applications. Even crushed stone used in road building and other construction projects must be mined. Mining affects our standard of living and impacts almost everything we do. A myriad of items that we use in our homes and offices and for transportation, communications, and national defense all require minerals (figure 2). For example, more than 30 different minerals are needed to make a television or telephone! Table 1 lists several commonly mined materials and some of the end uses in our daily lives.

Jan 1, 1995

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972