Search Documents

By G. V. Sullivan

The Bureau of Mines conducted preliminary beneficiation studies of a gold-bearing graphitic schist from Blue Hill, Tallapoosa County, Ala. The average analysis of the material was 0.08 oz/ton gold. Tabling of minus 35-mesh material recovered 83 to 94 percent of the gold at grades of 6.925 to 2.165 oz/ton, respectively. A combination of jigging and tabling resulted in a concentrate assaying 24.3 oz/ton gold and contained 87 percent of the total gold. Treatment of the material by jigging, tabling, and amalgamation recovered 86.5 percent of the gold.

Jan 1, 1969

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By C. K. Man

Coal dust explosions are routinely conducted within the full-scale experimental mine at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM) to meet the needs of numerous safety and health research programs. Many of these explosion tests over the years involved igniting different coal dust and limestone rock dust mixtures (up to 80% by volume rock dust). Following four more recent tests, floor dust samples have been collected and analyzed using the alcohol coking test and scanning electron microscopy (SEM) and the results compared to estimate the flame travel.

Jan 1, 2009

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By Louis A. Turnbull, JOSEPH J. SHIELDS

The Bell & Zoller Coal & Mining Co. recently completed construction of two slopes at Mine 3 near Zeigler , Ill . The slopes are in the Big Muddy River Valley , and construction was particularly difficult because the strata from the surface to a depth of 70 feet comprise water saturated sandy clay and sand . Many mining companies have similar shaft- and slope - sinking problems , and because these slopes were satisfactorily completed and now are in use the methods followed during construction are described in this information circular . It is believed that other companies with similar problems . will benefit by adopting the methods followed at Mine 3 .

Apr 1, 1949

By Jack C. White

The purpose of this Bureau of Mines research was to determine the technical feasibility of direct sulfuric acid digestion of Florida land-pebble phosphate matrix. Preliminary tests in a continuous digestion circuit showed that 92 to 96 percent of the P2O5 contained in the matrix was extracted, while the P.05 concentration in the product acid ranged from 21 to 30 percent. The waste filter cake contained about 1 percent P205 and up to 18 percent water. These sandy compact filter cakes, comprised mostly of quartz and gypsum, appeared to be suitable for backfilling and reclamation of mined lands.

Jan 1, 1975

By Frank L. Hess

In the first cart of that little space of time that we have designated as the nineteenth century, chemistry had reached a wonderful stride. Viewed from the present heights attained by the efforts of innumerable chemists with perfected apparatus, mire reagents, air under pressure, water, gas, and electricity conducted to the desk, and. numberless other helps, it seems marvelous that chemists of that day obtained such results. In 1820, about half of the elements had. been discovered; of these discoveries, Swedes had made 15 or more, about once-third of the elements then known and nearly half of those discovered after 1700.

Jan 1, 1939

A significant amount of information regarding the crushed stone and sand and gravel industries in each State is available from State agencies and State trade associations. These organizations continuously monitor the State mineral industries and are therefore an important source of detailed information at the local level. This third edition of the directory was prepared to provide a listing of government agencies and trade associations that can assist the users interested in obtaining detailed listings of crushed stone and sand and gravel producers, in addition to the information published by the U.S. Bureau of Mines.

Jan 1, 1994

By H. F. Feldmann

This work was done to provide thermodynamic, electrical, physical, and compositional data on the seeded combustion plasmas of seven coals for the design of MHD generators. The systems were assumed to be at equilibrium, and the design data were generated by solving for the composition of both gas and liquid phases with a digital computer. The coals reported in this study include a western subbituminous, a Pennsylvania anthracite, and five representative bituminous coals. The data include dewpoint temperatures of both slag and seed. A Mollier diagram for each coal is given to allow graphical generator calculations.

Jan 1, 1970

By Frank E. Cash

Accident prevention is an integral part of the operating procedure of the petroleum industry, and refinery officials and employees throughout the United States are exerting concerted effort to reduce the frequency and severity of accidents and are realizing definite results. In other words, the petroleum industry is safety conscious to a much creator decree than most of the other mineral industries. On January l, 1936, there were 11 operating, refineries in Louisiana with a crude-oil capacity of 199,750 barrels per day.4/ This report deals with safety in four of these refineries representing. 72 percent of the refinery capacity of Louisiana.

Jan 1, 1940

By James S. Browning

Domestic production of lithium minerals, source of the lightest metallic element, has increased from an average of 1,327 short tons of concentrate in the 1935-39 period to approximately 37,830 short tons in 1954. This rather phenomenal growth in production and use reflects growing industrial interest in the metal and its salts. This information circular has been prepared to summarize for the casual technical reader the reserve, mining, processing, and consumption situation pertaining to the mineral spodumene - the principal source of lithium. A relatively complete bibliography is included for those who may need more detailed information.

Jan 1, 1958

By O. C. Blade

The southeastern region of the United States is becoming more important as a petroleum-producing area, and it is receiving increasing attention from oil operators. In 1948 total production of crude oil from six southeastern States - Alabama, Florida, Kentucky, Mississippi, Tennessee, and Virginia - was 55,244,000 barrels, which represents 2.7 percent of the Nation's output during that year. Kentucky and Tennessee have produced crude oil since the early days of the industry, but the remaining four States have had production only few years. Data on annual production of crude petroleum in the six States are given in table 1.

Jan 1, 1950

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.

By P. Cole Gregory, Michael R. Yenchek, John C. Edwards

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were under- taken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 1993

By E. R. Spencer, E. Reeves

National Institute for Occupational Safety and Health (NIOSH) researchers conducted an investigation to quantify sound levels and to determine the amount of sound reduction provided by engineering noise controls installed in a talc processing plant. Baseline sound level and sound intensity measurements were performed at the plant and the measurement locations were recorded for comparison to post-control measurements. Follow-up measurements were then made at the same locations after the initial noise controls were installed. The plant subsequently decided to implement additional noise controls and the researchers returned to conduct measurements for a final analysis of all noise controls. The most significant results showed a sound level reduction in the main mill area from a range of 93-104 dB(A) down to 90-94 dB(A), and a total sound power level reduction of 21 dB(A) for air classifying mill 3.

By R. Van A. Mills

Rapid deterioration and destruction of metal equipment in oil and gas fields cause waste of resources and financial losses that must be lessened or eliminated if operations in many important fields are to continue profitable. The magnitude of this destruction is proved by the huge consumption of iron and steel pipe, tubing, casing, pump valves, and sucker rods to replace worn-out equipment, and by the amount of such equipment that is left in wells or junked. (See PI. I, A and B, and PI. II, A and B, and Fig. 14, p. 61.) This destruction of equipment constitu~es in itself a serious waste, but contingent production troubles, such as underground leakage of oil through defective tubing and pumps, and the consequent loss of oil and gas because of damage to pay sands by infiltrating water and silt, frequent and costly repairs with necessary suspension of production, and the ultimate injury to or loss of valuable wells, often cancel all operating profits. Many of these troubles result from rapid destruction of metal equipment by corrosive waters. The strata penetrated by the wells usually contain saline waters. Certain types of these waters, with their associated gases, are intensely corrosive; they attack well casing or tubing so vigorously as to riddle it with holes, rendering it useless in a few years or even a few months or weeks after it is installed. Pump plungers, working barrels, balls and seats of valves, and screen pipe, as well as lead lines and other surface equipment, are ruined with equal rapidity. The development and application of practical methods to retard or prevent this corrosion are among the most urgent problems of the oil and gas industry. Although much progress has been made in preventing the corrosion of metals, the need for reducing the damage from corrosion in oil and gas fields is still imperative. This is especially true of underground corrosion in the wells, because underground conditions favor corrosion and are difficult to study; hence they have not been thoroughly understood. In efforts to stop ~amage to oil and gas field equipment by corrosion, numerous methods have been proposed or tried with varying success. Some of these methods are cheap and effective. However, it is surprising that in many important fields the damage by corrosion is accepted as necessary or unavoidable, although cheap and effective methods that have been developed and successfully tried elsewhere might greatly reduce the trouble or eliminate it. This bulletin describes common causes and effects of oil and gas field corrosion and outlines methods of abating the damage. In order to accomplish this purpose best, the writer has avoided taking sides in controversies between the advocates of different metals for oil-field use; instead he describes the methods of combating corrosion in the various fields and suggests experiments that may yield valuable results. Throughout the paper he has freely used information from published reports of other investigators.

Jan 1, 1925

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains-- maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

Avoid errors in determining the amount of trace elements in overburden when core drilling samples, particularly as required by PL 95-87, the Surface Mining Control and Reclamation Act of 1977. Reason Metal additives present in certain drill stem joint lubricants appear to contaminate overburden samples. If these lubricants are used in assembling the drill string, they can interfere with the analytical methods used to establish concentration of trace metals. Errors In trace element determination appear to be as much as 30 times true concentration, and may falsely Indicate that the amount of trace element in the overburden exceeds the

Jan 1, 1981