Search Documents

By P. C. Good

Tungsten metal in fused form and of high purity was prepared by reducing tungstic oxide with redistilled calcium metal in a heavy-walled sealed reactor. Alloys of tungsten with vanadium, molybdenum) chromium, columbium, and tantalum were prepared by coreduction of mixed metal oxides in the same manner. This work was undertaken by the Bureau of Mines to investigate new approaches for preparing tungsten and its alloys in high-purity form. The standard method of producing tungsten metal has been the reduction of tungstic oxides by hydrogen. The resulting metal powder is compacted, sintered, and fabricated by powder metallurgy methods. Long experience in this field has resulted in the development of a technology that (by careful control of the variables such as metal composition, particle size, and sinterng technique) is well adapted to producing wire and the small shapes usually prepared from tungsten metal.

Jan 1, 1961

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977

By E. M. Tignor

A research program to aid development of improved methods for increased production of petroleum from partly depleted reservoirs is a vital part of the Bureau of Mines effort to effect true conservation of that mineral resource. This report presents results of an investigation to identify the clay minerals within some Appalachian petroleum-reservoir sands, the effect of clay content on the fluid-flow behavior of those sands, and the use of brines in water-flooding operations. Permeability measurements using kerosine, calcium chloride brine, simulated oilfield brine, potassium chloride brine, sodium chloride brine, and distilled water were made on reservoir-rock cores. Clay fractions were separated from sand grains of disaggregated portions of each core sample, and the clay minerals were identified by the differential thermal analysis method. Relations of the permeability to various fluids were developed.

Jan 1, 1957

By R. V. Lundquist, H. Leitch

The solubility characteristics of mono calcium aluminate (CaO A₁₂ 0 ) in water and in NaOH , Na₂ CO₂ , and NaOH - Na₂ CO₂ solutions were measured by determining the changes in Al2O3 concentrations in solution over a period of time at a specified temperature . The monocalcium aluminate was synthesized by sintering its starting components for 72 hours at 1,375 ° C. Distilled water and aqueous solutions of technical grades of NaOH and Na₂ CO₂ were used as solvents . The extraction of alumina from the monocalcium aluminate was dependent on the composition of the solvent and partially dependent on temperature for leaching . About 98 percent extraction of alumina from the aluminate occurred in Na₂ CO3 solutions containing 10 to 12 percent NaOH . Other solution compositions produce lesser extractions .

Jan 1, 1963

By R. P. Adams

Because of the extreme interest in materials with high melting temperatures and the advantages offered over the powder route for making high-density material, arc-melting and centrifugal-casting methods were investigated for preparing shapes of hafnium carbide with and without excess carbon. Highly satisfactory equipment was constructed and efficient operating procedures were established. Also, methods for preparing consumable electrodes and shrink-tolerant graphite molds were developed. Although crack-free hafnium carbide (6.3 weight-percent carbon) shapes were not made, coherent castings containing 9 to 13.5 weight-percent carbon were produced; the same compositions were shown to be resistant to thermal shock. Selected physical and chemical tests were performed on castings chosen for investigation by chemical and nondestructive inspection techniques. Electrical conductivity and thermal expansion measurements were made. Measurable oxidation of all the compositions studied was observed to start between 500° and 600° C. Attack by nitrogen, however, did not occur until temperatures exceeded 2,000° C. A linear relationship of the logarithm of the diamond pyramid hardness to the temperature was noted. Considerable scatter of the bend-rupture strengths at room temperature and of the tensile strengths up to 2,000° C was found. However, at the latter temperature and above, a definite relationship of strength to temperature was observed and some ductility was noted.

Jan 1, 1968

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By R. C. Buehl

[Improvements in refractories for high-temperature service have made possible the use of higher temperature in many processes. Consequently, it sometimes is desirable to use gases heated above 1,600° F., and for moderate rates of gas flow, there gases can be heaters best with pebble heaters. Pebble heaters of the stationary-bed type in which the chanber was lined with mullite brick and pebbles of pure alumina served as the heat-exchange medium have been used recently to heat the air blown into an experimental blast furnace4/ These pebble heaters worked well and made it possible to use air temperature up to 2,500° F. at the tuyere of the furnace. Since little has been published on this type of gas heater, a review of the construction on employed and operating data should assist in selecting applications and designing units.]

Jan 1, 1953

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By L. E. Cardwell

This publication contains routine analyses and related source data for 299 natural gas samples from 22 States and three foreign countries. All of the samples were collected during calendar year 1972 as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Fourteen previous publications have presented the results of 9,902 gas analyses prior to 1972. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1973

By Eric R. Bauer

The magnitude and rate of advance of an inmine coal squeeze was deter-mined by measuring roof-to-floor convergence on a regular basis. A dial-gage tube extensometer was used to collect data. Using these measurements) Bureau of Mines employees drew contour maps and graphs to show the direction and rate of squeezing. Information on the rate of squeeze advance was used to determine whether steps should be taken to prevent roof and/or floor movement from closing an entire section of the mine and if alteration of mining plans was necessary to prevent further squeeze development. Data analysis revealed that the squeeze was decelerating; thus there was no need to strengthen support in the areas of the mine that were studied. Mining plans were altered, however, as a result of the findings of this investigation.

Jan 1, 1981

By R. F. Tenney

No detailed information has been published heretofore on the performance of small industrial-type anthracite stokers in building-heating service, apparently because of the difficulty of comparing the performance of one unit with that of another over an entire season's operation. Studies of competitive heating fuels have been similarly handicapped, and attempts to compare fuels are seldom technically sound in this investigation, the performance of a 60-in. Losch4 stoker burning rice-size anthracite in a standard commercial boiler was observed during a 4-month winter-spring season. It was used to heat two buildings at the Bureau of Mines' Anthracite Research Center at Schuylkill Haven, Pa., with the customary type of automatic pressure-range control. Attendance was limited to inspecting, fuel weighing, data recording, and ash removal. Results were computed daily and grouped by weekly periods to minimize daily irregularities. The same stoker-boiler unit had already been tested in a series of American Society of Mechanical Engineers (ASME) test code runs, with the stoker running continuously and with other conditions well stabilized A comparison of results from the code test and the building-heating tests provided information not available in the past for a single stoker unit, assisted in analyzing heat losses not computable in a cyclic operation, and established a basis for evaluating stoker performance in heating service.

Jan 1, 1963

By R. H. Sprute

The Federal Bureau of Mines performed laboratory tests using direct current to dewater and densify fine-grained coal sludge in order to alleviate disposal problems and lead to recovery of high energy value often present in this waste. The laboratory tests described in the main body of the report were performed on thickened underflow (no flucculant added) from a northern Appalachian coal preparation plant. Solids in this slurry was very fine with 65 percent of the particles less than 0.1 mm in diameter. A variety of application procedures tested is exemplified by a test in which a soupy slurry (55 percent dry-weight moisture content) was converted into a firm dense material with a 20-percent dry-weight moisture content. These results were achieved in 3 hours with current density of 3.7 amp/ft2 and a power expenditure of 35 kwhr/yd3. The treated material has an average heating value of 10,400 Btu/lb. Varying current density, electrode configuration, and placement depth makes application of the treatment flexible. Two other types of sludge were tested briefly--thickener underflow from a southern Appalachian coal preparation plant with flocculant added, and sludge from an acid mine drainage treatment plant. The underflow responded well to the treatment, but response of the sludge from the acid mine drainage treatment plant was poor.

Jan 1, 1976

Reduce exposure of longwall face workers to respirable dust generated during the advancement of roof supports. Approach Identify and implement current water-application and improved support-movement practices used to lower support-generated dust. Defining the Problem Bureau studies have shown that on some longwall faces support dust can contribute over 30 percent of the respirable dust exposure of face workers. Conditions contributing to high levels of respirable dust generation during support movement are: depth of cover greater than 1,000 ft; immediate roof consisting of coal top or friable shales; and face-air velocities in excess of 500 fpm. Moreover, at most longwalls, supports are advanced on the intake-air side of the shearer as it travels with the airflow. This places the shearer operators, and in many cases the support movers, downwind of support advance, thus increasing their respirable dust exposures.

Jan 1, 1984

By John C. Ferm

This report contains a summary of Phase I and complete results of Phase II portions of a study of geologic factors associated with roof falls in mines on the Pocahontas #3 coal seam in southern West Virginia and southwestern Virginia. Principal objectives of Phase I was the selection of five mines that best portrayed the spectrum of roof and mining conditions and Phase II consisted of a measurement and documentation program for each of the five mines. The documentation measurement program included reconnaissance mapping, detailed mapping, joint measurements and coring roof rock. 1.2 PHASE I RESULTS The results of Phase I consisted of the selection of the following five mines for detailed study: Virginia Pocahontas #3 (Island Creek Coal Company), Bishop (Consolidation Coal Company), Shannon Branch (Allied Chemical Company), Keystone II (Eastern Associated Coal Company) and Macalpine-East Gulf (Westmorelenad Coal Company). In addition, Phase I results, which were based on questionnaire data, indicated that the kind of rock in the roof --gray sandstone, crystallized sandstone, laminated sandstone and shale, grey shale, slickensided shale, and rider seams could be associated with good and bad top areas. Also presence of vertical separations, bolt length, entry and cross-cut width, length and torque on bolts and depth of overburden seemed to be related factors. These data provided a focus for the Phase II measurement program.

Jan 1, 1975

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By Joan T. May

The Bureau of Mines conducted laboratory tests to evaluate the production of high-purity H3P04 by HCl digestion and solvent extraction. Both batch and bench-scale continuous tests were made. Western phosphate rock concentrates were acidulated with HCI, and the digestion liquors were processed by solvent extraction. Phosphoric acid was extracted with isoamyl alcohol and recovered from the organic extract by contact with an NH4F solution. This solution was fractionally distilled to yield high-purity H3P04. The raffinate from solvent extraction was treated with lime to precipitate CaF2, which was subjected to steam pyrolysis to generate HF. This method was successful in recovering 95 pet of the phosphate and 80 pct of the fluoride contained in the concentrates.

Jan 1, 1976

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

The coal-bearing regions of Colorado cover approximately 29,600 square miles, which is 28.4 percent of the state's total area. The most important coal-bearing regions are located in the north western and west-central parts of Colorado. Coal resources vary from lignite to anthracite. More than 70 percent are bituminous; 23 percent subbituminous; 5 percent lignite; and less than 1 percent anthracite. The state's coal reserves total about 17.2 billion tons, 3.5 percent of national reserves. Approximately 8.8 million acres of coal rights in the state are owned by the Federal Government; on about 72percent of this land, the Federal Government controls both the coal and the surface rights. It is estimated that approximately 4.2 billion tons of coal reserves are under federal ownership in Colorado. Permitted acreage of mines in Colorado ranges from 40 to 13,114 acres. Differences in elevation create many climatic zones in Colorado. Local annual precipitation can average less than eight inches in some areas in extreme western Colorado to more than 30 inches in certain mountainous areas. Generally, precipitation rates are low at most mine sites, making revegetation difficult. Colorado gained primacy when its regulatory program was conditionally approved December 15,1980. The Abandoned Mine Land Program was approved June 11, 1982.

Jan 1, 1992

By R. Marshall

Electrical trailing cable handling techniques and practices used in metal and non-metal surface mines were investigated by obtaining information through actual visits to the mine properties located in a variety of geological areas and climatic conditions. An analysis was made of all accidents related to cable handling which are cataloged by HSAC* for the period from 1971, through June 1980. Information was also collected from mine operators concerning near accidents and non-reported accidents. The results of this investigation were presented to the U.S. Bureau of Mines in an effort to outline recommended practices for cable handling in surface mines and to recommend additions and/or changes in the present regulations now being enforced by MSHA** field inspectors. These recommendations are also intended to assist the U.S. Bureau of Mines in evaluating the need for assisting the mine operators in the areas of training and distribution of information related to material handling of trailing cable. * Health Safety Analysis Center ** Mine Safety & Health Administration

Jan 1, 1980

By T. L. Hebble

The Bureau of Mines investigated a hydrometallurgical procedure to recover Co, Ni, and Cu from an electrolytic zinc industrial copper filter cake. The copper filter cake is presently unmarketable or of low value because economic and environmentally acceptable processing technology is lacking. Research by the Bureau of Mines has developed a multistage process for recovering or recycling over 93 pct of the Zn, Cd, Cu, Co, and Ni from this material. The stages involved are (1) wet sizing, (2) H2S04 leaching of undersized material, (3) H2S04-Mn02 leaching of H2S04 leach residue, (4) selective precipitation of As, Cu, and Co-Ni products, and (5) precipitation of manganese for recycling to the leach circuit. The final process residue is only 1.6 wt-pct of the initial cake and consists of lead sulfate.

Jan 1, 1981