Search Documents

Reduce injuries caused by slips and falls from large haulage vehicles. Approach Replace the flexible-cable or chain-type lower ladder steps, with steps that extend closer to the ground and do not sway when stepped on. Modify dimensions of entire ladder to new industry recommendations. How It Works New lower ladder steps are supported by side pieces made of pretensioned, solid-wound, coil springs fabricated from high strength steel. Unlike conventional crash-resistant steps, which flex or swing freely when stepped on, the spring supported steps can maintain the same inclination as the fixed upper portion of the ladder while supporting an average-weight operator. The steps are also highly resistant to collision damage because they yield on impact if rammed into obstructions such as rocks or berms. See photograph.

Jan 1, 1980

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines to determine its effectiveness for recovering copper and silver from a tetrahedrite concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained coppers, silver, lead, zinc, antimony, and arsenic. Parameters affecting metal extraction (such as temperature, pressure, amount of ferrous chloride, and initial hydro-gen ion concentration) were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per square inch gage (psig) and 100° C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, antimony, arsenic, and sulfur reported to the tailings.

Jan 1, 1978

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

Capture airborne coal dust generated by a continuous mining machine to reduce workers? dust exposure and to improve face visibility. Approach Develop a low-profile dust collector system which can be mounted on the boom of a continuous miner. How It Works When coal is mined with a milling head continuous miner, a substantial amount of coal dust (respirable and non-respirable) escapes the dust suppression sprays at the cutter head. This can cause poor visibility around the cutting head and can expose the workers to high levels of respirable dust. A practical means of removing this dust is with a scrubber mounted directly on the mining machine. Under a Bureau of Mines contract, a low-profile, machine-mounted dust collector (MMDC) was developed to avoid adding extra height to the continuous

Jan 1, 1983

By D. G. Kesterke

Research was conducted to determine the feasibility of extracting elemental oxygen from silicate-bearing melts by high-temperature electrolysis. The method was based on a modification of existing processes for electrowinning metals from their oxides dissolved in molten halide systems. Electrolyses were performed at temperatures ranging from 1,050° to 1,250° C in boron nitride cells that incorporated a silicon carbide cathode and an iridium anode. The electrolytes contained volcanic scoria as the oxygen source, plus mixtures of BaF2 and LiF as fluxing agents. Cell gases containing almost 14 volume-percent oxygen were obtained. The average anode current efficiency for several experiments of extended duration was calculated to be 55 percent. Cell design and operating conditions are described, and some of the problems associated with the process are discussed.

Jan 1, 1971

Develop methods to detect and repair poorly functioning dust collectors on roof bolters. Approach In conjunction with a research project to reduce silica dust in coal mines, a variety of roof bolting machines operating under different conditions were examined to find out how much these machines were contributing to the silica dust problem. Results The investigation concluded that if the bolting machines' dust collector is properly maintained, very little dust can be measured in the air, even with minimal airflow over the bolter. Poor maintenance, however, frequently results in high dust levels. Three major problem areas were found. These were: (1) filter leaks, which allowed dust to escape, (2) accumulations of dust in the collection system, and (3) low airflow at the bit due to hose, fitting, and relief valve leaks.

Jan 1, 1984

By W. W. Weller

This report provides low-temperature heat-capacity data and entropies at 298.15° K. for magnesium metavanadate (MgV206) and magnesium pyrovanadate (Mg2V207). The work completes low-temperature measurements planned for alkaline-earth vanadates; an earlier report dealt with calcium vanadates.4 No similar data for these compounds have been published previously. Free energy of formation values at 298.15° K. were derived by combination of the present entropy values with heat of formation data. MATERIALS The materials used in the measurements were portions of the samples described in a previous Bureau of Mines publication by King, Koehler and Adami.5 Methods of preparation, chemical analyses, and X-ray examinations are covered in this paper. The indicated purity of the samples was 99.9 pct.

Jan 1, 1962

By William J. Wiehagen

This is the third in a series of four articles that discuss underground fire-fighting preparedness. As with the first two articles, it is based on interviews with 214 miners conducted at 7 underground coal mines (referred to as Mines ?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996]. In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. In this article, we describe miners? experience in fighting underground mine fires and present their perceptions of training and readiness for fire-fighting.

Jan 1, 1997

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was toe valuate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of with standing explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By J. P. Conway

The yielding-rock-bolt concept, as developed in South Africa, consists of a smooth-bore die or collar fitted to a standard rock bolt. Laboratory testing at the Bureau of Mines Spokane Mining Research Center under slow and fast strain rates showed that extrusion loads can be controlled by varying the configuration of the die bore and that theoretical analysis (using basically Sachs' theory of wire drawing) predicts extrusion loads of the different die-bore configurations. A derived equation, based on this research, can be used for designed die-thread combinations for any desired extrusion load. Dynamic loading resulted in slightly higher loads (15 percent) than static loading. The strain hardening effect, which increases yield and ultimate strength, was partly offset by adiabatic heating of the threads, which decreases strength.

Jan 1, 1975

By J. J. Wallace

This report describes the initial phase of Bureau of Mines research in the hydraulic mining of bituminous coal. The mining site and equipment are described, and the test procedures and results obtained with a bar-mounted monitor are given. Tests showed that hard Pittsburgh-bed coal can be mined hydraulically from a solid face at water pressures of 4,000 pounds per square inch.4 Coal was penetrated to a depth of 4 feet in 20 seconds with 225 gallons of water per minute coming from a 3/8-inch nozzle at 4,000 pounds per square inch pressure. Some difficulty was encountered in cutting the binders occurring in the coal; it was not possible Lu penetrate directly the overlying draw slate.

Jan 1, 1961

By R. K. Koch

The Bureau of Mines produced several series of titanium castings in order to investigate the feasibility of producing commercial-grade titanium castings in bentonite-bonded olivine or zircon sand molds. The use of these molds for titanium casting was investigated as a possible alternative to the industrially used rammed graphite process. Parameters investigated were mold mixtures, mulling, gating, venting, drying, and mold washing. The investigators found that castings with superior ductility and fatigue life, compared with rammed graphite castings, could be made by fume-free pro-cesses in molds bonded by western bentonite, using either olivine or zircon sand. Zircon molds were satisfactory for both light-and heavy-sectioned castings. However, olivine molds were suitable only for light-sectioned castings because the mold-metal reaction became excessive during the pouring of heavy-sectioned castings.

Jan 1, 1981

By Vernon O. Markworth

This report contains the results of tests performed on three large diesel engines to determine their ability to meet selected criteria of the Mining Enforcement and Safety Administration Regulations for equipment used in gassy, non-coal mines. Study efforts were first directed toward determining the types of equipment expected to be used in underground oil shale mines. Three typical engines in the 800-1200 horsepower range were then selected for testing. Intake flame arresters, exhaust scrubbers, and water jacketed exhaust system were designed and built for each engine. During testing, each engine was evaluated for its gaseous emissions output, adequacy of the exhaust gas cooling system, ability to withstand internal explosions, and adequacy of the flame arresters. Surface temperatures of the engine and exhaust cooling system were determined under full load operation.

Jan 1, 1978

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

By Catherine C. Kilgore

The Bureau of Mines investigated the availability of fluorspar (CaF2) from 36 U.S. and 50 foreign mires and deposits in 13 countries. Only 6 U.S. properties are considered to be economic, as 29 domestic deposits were found to have an average total cost of production that was uneconomical at a breakeven (0-pct) discounted-cash-flow rate of return (DCFROR). The 50 foreign properties evaluated represent at least 55 pot of demonstrated fluorspar resources located in market economy countries and China. Al I evaluated foreign operations were found to be economic to marginally economic in January 1984 dollars when compared against published prices for each country. Reserves for 56 properties totaled 97 million metric tons (mt) (recoverable Ca F,) from demonstrated ore resources of 344 million mt that contained 123 million mt CaF2. The average total cost needed to cover all costs over the life of each operation was determined for all recoverable fluorspar products. Comparisons of ruining, beneficiation, and transportation costs per metric ton of fluorspar concentrate illustrate advantages between countries. Of the three countries with the greatest fluorspar production, China, with its high-grade, low-cost operations had the lowest weighted-average total cost of production ($38/mt concentrate), Mexico was next, at $54/mt concentrate, and benefited in U. S. dollar terms from the devaluation of the peso. The Republic of South Africa needed an average of $90/mt of concentrate to cover all costs of production at its large low-grade deposits.

Jan 1, 1985

By J. Grumer

The Bureau of Mines, under the sponsorship of the Space Nuclear Propulsion Office, conducted a laboratory-scale hydrogen safety study which determined several combustion characteristics of hydrogen diffusion flames. Experiments show that ambient air may enter the top of a hydrogen flare stack when the hydrogen flow is low. A new concept, supported by photographic evidence, predicts that diffusion flames burning in air on a wide, upright pipe (stack) and fed with slow, upward flows of buoyant gas will induce a downward flow of air along the walls of the pipe that can support combustion within the pipe. Predicted flamedip limits agree roughly with experimental values determined on 6-, 12-, and 18-inch-diameter stacks and increase with increasing stack diameter. Measurements were made of the limiting flow at which a hydrogen diffusion flame blows out in still air. By means of an empirical application of the critical boundary 8 velocity gradient concept, these data lead to a blowout limit of about 10 reciprocal seconds for a hydrogen diffusion flame. Burning rates of large hydrogen diffusion flames ranging from about 0.03 to 1 ft/sec were used to predict approximate flame heights on flare stacks. Temperatures of larger hydrogen diffusion flames up to about 3,600° F were observed, but the most representative value appears to be about 2,600° F. It was found that crosswinds do not strip significant amounts of unburned hydrogen from its diffusion flame and that water-cooled flare stacks are not likely to be damaged when flame is blown back into them by opposing winds.

Jan 1, 1970

By Gerrit V. R. Goodman

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 4D ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face? 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm. This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 4D ft.

Jan 1, 2010