Search Documents

By Howard E. Parkinson

A brief description is given of various Bureau of Mines research activities that have begun since July 1974 and are not being reported on by others at the Third West Virginia University (WVU) Conference on Coal Mine Electrotechnology. An essential feature of the various projects is that they are pragmatic. The projects are applied research and are carried out both by the Bureau in-house research group and by other research groups through contract research. Projects have been directed toward wired-type communications with a special effort to modify the wired systems so as to be more effectively used. The projects are in three groups: Pager phone systems, trolley line phone systems, and guided-wire wireless communications. Also, a brief sketch is given of research that is essential for further developments in mine communications. From the early results of these various projects, the Bureau has good reason to project that there will be improved performance of existing communication systems and that communications will be extended to other individuals working in areas that are excluded from present mine communication systems.

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

Improve the safety and reduce the cost of longwall entry support. Approach Replace the conventional wood cribbing with stronger, non-rotting and lower cost cribbing made of steel-fiber-reinforced (SFR) concrete. How It Works Conventional concrete can suddenly fail under excessive compression loads, but adding steel fibers to the concrete, before it is mixed with water, changes the failure mode to a gradual and controlled failure characteristic similar to wood. A system for making SFR concrete crib blocks was designed and developed (or use in constructing walls and cribs to support coal mine roofs. The SFR concrete cribbing is stronger and stiffer than wood, and avoids wood's disadvantages of: flammability, deterioration under chemical or bacteriological attack, methane generation, and relatively high cost. Use of SFR concrete also allows freer movement of miners, equipment, and ventilation air, because much less volume of SFR concrete is required than wood for a given amount of support, and because the roof-to-floor closure is greatly reduced by the stiffer supports.

Jan 1, 1981

Develop a more efficient method of testing the integrity of in-situ leach mining operations. The Problems For economic and environ-mental reasons, in-situ leaching operations must be sure that wells do not leak. Loss of solution in large quantities can be expensive in itself, and if such losses result in pollution the costs can be even higher. Wells are usually tested for leaks by sealing them with packers, pressurizing them and monitoring the pressure drop. However, many commercially-available packers are designed to be used in steel-cased wells rather than the fiberglass-or plastic-cased wells used for in-situ mining. These packers are heavy, cumbersome, expensive, and often leak. In addition, commonly used well-integrity-test systems require lengthy test periods and drill rigs or hoist trucks with rigid pipes must be used to run the packers in and out of the well. The Bureau of Mines has developed a mobile, self-contained leak-testing system that is faster, uses trailer-mounted equipment that can be operated by one person, and features a new inflatable packer.

Jan 1, 1985

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By P. G. Barnard

Losses of alloying metals in furnace flue dusts, grinding swarfs, and mill scale produced during the manufacture of stainless steel are substantial. About 25 million lb Cr, 8.7 million lb Ni, and 150,000 lb Mo and other critical metals can be made available annually for recycling by a process developed by the Bureau of Mines. Stainless steel wastes pelletized with a portland cement binder were reduced in a small electric-arc furnace by a two-stage process to produce a recyclable alloy containing Cr, Ni, Mn, and Fe. The initial reduction was with carbon; the second, with ferrosilicon. Results are compared with previously reported laboratory induction melting tests. A 2,000-lb demonstration test of the process in a commercial electric-arc furnace is also described. Data are also presented on three 1,500-lb tests made using various slag conditions in the electric-arc furnace. Recoveries up to 99 pct of the Fe, Cr, and Ni contents of stainless steel wastes were obtained in using the process.

Jan 1, 1977

By J. M. Singer

Approximate equations were used to compute the radiant heating of float coal dust by approaching flames for various combinations of particle size, dust path length (flame travel distance), flame temperature, dust concentration, flame speed, and flame length. The computed values of degree of radiant heating and flame travel distance for preheating the coal dust should be useful for estimating the increased fire hazard of different coal dust-flame parameters. Some findings relating to coal mine disaster control are-- 1. Coal dust clouds cannot be preheated to ignition temperatures by flame radiation alone when deflagration speeds are greater than about 10 m/sec. Thus it appears unlikely that radiation alone will cause flames propagating in dust clouds to accelerate to detonation velocities. 2. Small particles in the radiation flame zone caused by burnout and soot formation increase the degree of preheat significantly. 3. The concentration of float coal dust (radii = 3 to 40 microns) for maximum radiant heating usually peaks in the range 50 to 200 mg/liter of air.

Jan 1, 1970

Improve the safety of salt mine workers by providing a means for quickly identifying areas within the mine that?s how an increased potential for gas and salt outbursts. Approach Outbursts occur in salt mines when a high-pressure pocket of gas is intercepted during the mining process, resulting in a sudden and sometimes catastrophic expulsion of gas and salt. In one case, the amount of gas released through such an event caused an explosion that resulted in five fatalities. The U.S. Bureau of Mines has designed and developed a gas outburst prediction system that can quickly determine the potential instability of areas within rock salt mines. The determination is based on noise measurements obtained from samples of the salt as they are dissolved in water. This system improves upon technology currently available because it provides information in only a few minutes instead of in several days. In addition, present prediction systems are not only time consuming, but expensive because they require laboratory conditions and highly trained personnel to operate them and determine results.

Jan 1, 1989

By A. F. Colombo

Infrared spectroscopy employing attenuated total reflectance (ATR) techniques on thin films of dried gelatinized starch solution was used during Bureau of Mines research to determine the structural and impurity differences in starch products and to correlate these characteristics with the flotation response of a nonmagnetic taconite. All of the starch products evaluated gave spectrograms which were characteristic of the anhydroglucose monomer and its polymerization product. Distinct infrared absorption peaks caused by the protein molecule were observed and were used to classify the starches. Correlation of laboratory flotation of calcium-activated gangue from a Mesabi Range nonmagnetic taconite and infrared spectra produced from gelatinized starches showed that protein impurities and linear chain structure limited the effectiveness of starches as iron mineral depressants. Starch products having spectrograms similar to pure amylopectin were generally good depressants for iron oxides, were effective at about one-half the addition that was required for starches that gave infrared responses similar to pure amylose, and yielded acceptable iron concentrates containing 61.5 percent iron and 6.5 percent silica.

Jan 1, 1969

By J. D. Marchant

As part of its mission to assure the maximum recovery and use of the Nation's mineral resources, the Bureau of Mines, investigated an improved procedure for producing rare earth-silicon alloys. For example, a charge consisting of 681 grams of mixed rare-earth oxides, 309 grams of ferrosilicon (75 wt-pct Si), and 182 grams of aluminum metal along with a flux consisting of 681 grams of CaO and 45 grams of MgO was reacted at 1,500° C in an induction furnace. Good slag-metal separation was achieved. The alloy product contained, in weight-percent, 53 RE, 28 Si, 11 Fe, and 4 Al with a rare earch recovery of 80 pct. In current industrial practice rare earth recoveries are usually about 60 pct in alloy products that contain approximately 30 wt-pct each of rare earths and silicon. Metallurgical evaluations showed the alloys prepared in this investigation to be as effective in controlling the detrimental effect of sulfur in steel and cast iron as the commercial rare earth-silicon-iron alloys presently used in the steel industry.

Jan 1, 1980

By Thomas A. Gray, Lynn M. Crayne, Michael A. Trevits, Phil Glogowski

Mine seals can be remotely constructed in underground coal mines, through vertical boreholes, when direct access to a fire is impossible or considered to be too dangerous. This method has great merit because boreholes can be drilled to specific mine areas and seals can be positioned close to a fire zone. The technology however, can be largely ineffective if the constructed seals do not provide effective barriers to airflow or cannot be used to impound water and other inert materials. Unfortunately, no viable alternatives exist to sealing the entire mine at the ground surface. Full-scale remote mine seal construction research is being conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Lake Lynn Laboratory (LLL). Under this effort, Howard Concrete Pumping Company and GAI Consultants, Inc. have joined forces to evaluate a potentially significant improvement to the current state-of-the-art. This paper will cover development of novel technology for remote mine seal construction, evaluation of the materials used, construction practice, and follow-up testing.

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult, longstanding engineering problems associated with coal mining is the catastrophic failure of cog mine structures known as bumps. For more than 70 years, researchers and practitioners have assembled a wealth of technical information on coal bumps in an attempt to understand and control them. However, many technical issues raised long ago are still being debated today. This paper examines past experiences and recognizes achievements in the realm of coal bumps. U.S. Bureau of Mines (USBM) researchers collected and analyzed 172 coal bump incident reports and compiled the pertinent statistics into a database. Actual field studied are also discussed. Examination of past experience has shown that there is no one set of defining characteristics that is responsible for coal bumps. In all cases, bumps occur when complex arrangements of geology, stress, and mining conditions interact to interfere with the orderly dissipation of stress. However, it is evident from the database that a tremendous reservoir of knowledge has been established from past experience that has unquestionably limited the severity of coal mine bumps in the United States.

By R. A. Beall

A series of 45 zirconium ingots has been cast by the consumable electrode arc melting process with the object of analyzing the effects of power input from 50 to 230 kilowatts and reduced pressure furnace atmosphere to improve the quality of regular 8-inch-diameter production ingots made thereby. Electrode consumption rate, molten pool volume, melting efficiency, sidewall quality, arc stability, and yield efficiency are considered. The use of direct current and alternating current is studied. In conclusion, reduced pressure furnace operation is shown to promote electrical efficiency, ingot homogeneity, high metal yield, and are stability. INTRODUCTION Zirconium is a particularly difficult metal to melt because of its affinity for atmospheric gases and its solvent properties when molten. In addition, zirconium sponge as produced by the boll process contains minor amounts of magnesium chloride, which cause severe spattering luring melting, because of these difficulties with zirconium, and its sister metal titanium, near techniques have been developed to permit production of commercial size ingots. Among the more promising is the consumable electrode arc melting method.

Jan 1, 1955

By Charles Zahn

Gas chromatography is a method of separating mixtures of gases and volatile materials by entraining their vapors in a gas stream, which passes over an appropriate stationary phase. Two techniques are in common use: Gas-Liquid Chromatography, in which the stationary phase is a liquid supported on an inert solid, and Gas-Solid Chromatography, where the stationary phase is a solid adsorbent, such as charcoal or alumina. In both techniques components emerge from the column after a characteristic residence time. Gas chromatography is applicable as a qualitative or quantitative tool in a wide variety of problems in chemical research and processing. It may also be employed for purification and separation. A running bibliography on gas chromatography has been maintained at the Bureau of Mines synthetic liquid fuels laboratories, Bruceton, Pa., for several years for the benefit of research workers, who use chromatography as an analytical tool. Since the number of references grew and interest in the technique became more wide-spread, the Bureau is publishing this list rather than maintain it as a purely internal source.

Jan 1, 1958

By Eleanor Abshire

This bibliography is the result of a cooperative project undertaken by the Bureau of Ships and the Bureau of Mines to accumulate literature published to date on zirconium and hafnium and to establish an information center on these metals for the use of any interested research organization or library. This bibliography, which will be supplemented as additional information is accumulated, consists of references, with abstracts, to pertinent literature on the subject published from 1907 to date.

Jan 1, 1957

By Pedro Lilienfeld

This Final Report describes a program whose objective was to design, develop, fabricate, and test an airborne mass monitor for unattended and recording measurements of the concentration of dust in mining environments. Sensing collection are performed by beta-radiation attenuation and inertial implementation respectively. The instrument is portable, battery or line operated provides a digital printout of the mass concentration during each selection sampling period, as well as the accumulated mass of dust, and the elapsed sampling time.

Jan 1, 1974

By Robert C. Ellman

The Bureau of Mines investigated the factors that cause agglomeration of lignite by freezing during winter shipment and sought methods to avoid it. Tests showed that lignite may be freezeproofed by removal of the relatively small quantity of moisture involved in forming the frost crystals which cement particles together, or by controlling the crystal characteristics. Adding dried lignite fines proved to be an effective and superior freezeproofing method. Commercial adoption of this method has been successful.

Jan 1, 1965

By Philip C. Tully

This bibliography contains 3,062 different citations to technical and scientific literature about helium and alpha-particles abstracted by 13 abstract service publications during 1963. Multiple subject classification has increased the total number of entries to almost 5,000. Helium citations are listed by 23 major classifications. The number of subclassifications has been greatly increased to minimize the time required for literature search. The use of automatic data processing has been extended in compiling the bibliography.

Jan 1, 1970

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made before the turn of the century, used Moissen's pyrophoric manganese.3/ This material was made by electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941