Search Documents

By H. V. Makar

Ferrous fractions recovered from urban refuse were tested by the U.S. Bureau of Mines, U.S. Department of the Interior, to assess their character, composition, and response to detinning. This research was conducted as part of the Bureau's efforts to conserve mineral resources through recycling. Results from laboratory and pilot tests established the technical feasibility of detinning scrap recovered from household refuse. Detinned products containing less than 0.03 percent residual tin were produced. Concentrations of other residual elements were determined and compared with those in existing commercial scrap and with proposed specifications. Studies were extended to include evaluations under commercial conditions. Preliminary tests on 5-1/2 short tons of ferrous fractions revealed the need for adequate shredding to assure optimum metal-caustic contact and minimize retention of tin-bearing rinse solution in the final baled product. The washed metal product contained 0.06 percent residual tin. Subsequent melt tests showed a yield of 91.4 percent. Based on these studies, full-scale commercial demonstrations showed that detinned bales equivalent to No. 1 bundle quality could be produced in carload quantities. Up to 5 pounds of tin per gross ton of scrap is con-currently recovered during the detinning process.

Jan 1, 1979

By W. C. Smith

This Bureau of Mines report discusses how pull-test data can help establish polyester resin column length criteria for roof bolts in evaporite minerals. The study evaluates the effectiveness of partial to full columns of resin in anchoring 4-ft, No.6, grade 40 rebar roof bolts in potash, salt, trona, gypsum, and borate mine roofs. Pull tests were performed on over 600 roof bolts in 11 evaporite mines. Column lengths ranging from 6 to 48 in (fully grouted) were evaluated for each test site. In general, comparative results among all test sites indicate that pull-out loads in excess of 10 tons (force) were attained with resin-grouted bolts having 13 to 75 pet less than a full column of polyester resin. Ten tons (force) of load-carrying capability compared favorably, in terms of strength, with the calculated yield strength of the rebar used in the tests, which was 8.8 tons (force). The site-specific nature of each test site, due to the unique combinations of geology, mine-induced stresses, and other unknown parameters, prevented the establishment of valid generic column-length criteria. For these reasons, data to evaluate resin-column-length effectiveness are best obtained on a mine-specific basis.

Jan 1, 1987

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method&apos;s potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By James R. McVey

A new method for measuring deformations of rock surfaces in underground excavations has been suggested by Dr. James Powell of Brookhaven National Laboratories (BNL) and subsequently developed and successfully demonstrated in a mining environment by the Federal Bureau of Mines, Spokane Mining Research Center (SMRC) and Brookhaven National Laboratories. The system uses 35-mm photography of targets strategically located on surfaces of interest, such as across the roof and on the sides of a mine drift or tunnel. The optimum tar-get, as determined in this investigation, consists of a white ?X? made with 1/8-inch-wide reflective tape on a black 6-inch square. Photographs, taken in pairs from two separated camera positions and at regular time intervals, were analyzed at the Bureau by hand and at Brookhaven National Laboratories using techniques and equipment similar to those used in cloud chamber film analysis. Test results show that deformation-measurement accuracies of better than ±0.020 inch in a drift that is 20 feet wide can be expected. This degree of accuracy, plus providing displacement data in the X, Y, and Z directions (rather than the one direction formerly possible), makes this a noteworthy and useful tool for industry as well as for mining research.

Jan 1, 1974

By Warren D. Longwill

The Bureau of Mines inventoried Federal lands in the State of Oregon and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal status and agency management practices. The Bureau determined areas of the State having past mineral production and/or known metallic mineral resources and areas favorable for coal, oil, gas, and geothermal resources, and prepared maps that spatially compare the availability of Federal mineral land with these mineral areas to demonstrate the extent of restrictions to mineral entry. Oregon contains 62.1 million acres, of which 33.9 million acres or 55% is Federal mineral land. About 2.3 million acres of Federal land is favorable for selected metallic mineral deposits, of which 64% is available, 13% is restricted, and 23% is unavailable. Of the 21.1 million acres of Federal leasable land favorable for oil and gas, 68% is available, 11 % is restricted, and 21 % is unavailable. Of the 146,720 acres favorable for coal, approximately 71% is available, 13% is restricted, and 16% is unavailable. Federal leasable land favorable for geothermal resources amounts to 458,968 acres, of which 42% is available, 34% is restricted, and 24% is unavailable.

Jan 1, 1988

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980

By Gregory J. Chekan

This Bureau of Mines report presents three methods for designing bulkheads to impound water underground: (1) thin and thick plate design; (2) South African plug design; and (3) single and double bulkhead seal design. Related areas critical to the long-term effectiveness of underground water impoundments are also addressed. These include bulk-head anchorage, concrete specifications and placement, the grouting of permeable strata, and the sizing of barrier pillars. A case study involving hydrostatic tests conducted on a single bulkhead seal constructed in the Safety Research Coal Mine of the Bureau&apos;s Pittsburgh Research Center is presented in an appendix.

Jan 1, 1985

By C. E. Gregory

In terms of a Research Proposals supported by a Grant Agreement dated 30 June 1973, the author was commissioned to prepare an annotated bibliography of mine fires. The main objective was to conduct a comprehensive program of library research and search of official files to prepare a list of articles dealing with actual occurrences of mine fires. This bibliography as now completed includes an annotated reference from each article or report cited, underlining the cause, extent, methods used, procedural errors made, results achieved, ventilation effects, and lessons learned from the operation of subduing the particular fire.

Jan 1, 1974

By James W. Martin

This user&apos;s manual analyzes the application, selection and performance of front-end loaders in mining operations which can effectively utilize their load-and-carry capability. All aspects of the application are considered starting with a discussion of the load-and-carry system and alternate material handling methods. Site conditions such as the geology of the formation, material characterisitics, alternative mine plans and working conditions are identified. Selection considerations include machine design characteristics, production capabilities and ownership and operating costs. Typical operating practices and safety procedures are discussed. Comprehensive machine specifications, together with a series of checklists and worksheets, are included for preliminary analysis.

Jan 1, 1981

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By R. R. Allen

Gieseler plastometer tests were performed on eight western coking coals at retort - immersion depths ranging from 2 to 3-3 /4 inches (measured to the center of the coal charge ) . Increased maximum fluidities were associated with greater retort - immersion depths , the most pronounced increases being observed on highly swelling coals when tested at 3-3 /4 inches . The maximum fluidity of one of these coals when tested at 3-3 /4 inches was 146 percent greater than that observed at 24 inches . Retort - immersion depth had no significant effect on the temperatures of initial softening , fusion , maximum fluidity , end of fusion , and solidification .

Jan 1, 1964

By W. L. Cooley

The report provides a detailed analysis of 23 electrical accident countermeasures contemplated for use in the metal/non-metal mining industry. The costs and potential benefits of implementing groups of these countermeasures are estimated, and methods arc outlined by which the operator ran choose countermeasures in an effective manner. The analysis is based largely on an extensive electrical accident event tree which is developed in detail. For those countermeasures which are not currently technically feasible, several prototype devices were developed to help speed development. These included a trolley arc eliminator and a safer mine electricians multimeter.

Jan 1, 1982

By William H. Pomroy

The potential for large-scale fires in underground fuel storage and fuel transfer areas prompted the Bureau of Mines to study fire hazards in these areas and devise improved fire safety technology for use in these areas. This report describes the Bureau&apos;s research to characterize and quantify fire hazards in fuel storage and fuel transfer areas, develop guidelines for safe and efficient fueling system design, prepare specifications for automatic fire sensing and suppression systems for these areas, test prototype systems in the laboratory and in underground mines, and perform cost-effectiveness evaluations of the devised technology.

Jan 1, 1985

By E. Chin

Although Japan is a major producer of crude steel, it is poor in industrial raw materials. This Bureau of fines report describes Japan&apos;s raw material needs for chromium, cobalt, manganese, nickel, and tungsten to produce ferroalloys and alloy steels. Japanese imports of these ores or metals by quantity and source are given for 1972-81, inclusive, to indicate (1) the changes in the consumption and supply pattern, and (2) the degree of Japan&apos;s dependence on foreign sources. This report also describes measures implemented by Japan to reduce the risk- of supply interruption, and discusses the possible implications of supply shortages.

Jan 1, 1983

By Arthur V. Petty

The Bureau of Mines has researched the utilization of mining and pro-cessing wastes as raw materials for the production of glass-ceramic pipe. Characterization of various wastes as to occurrence and chemical composition is reported. A computer program was developed and used to identify waste materials and mixes that would result in glass melts from which glass-ceramics could be produced after cooling and subsequent heat treatments. The production of abrasion-resistant pipe from inexpensive and readily available domestic resources could offer an economical substitute for high-alloy steels containing the critical and strategic materials cobalt and chromium.

Jan 1, 1984