Search Documents

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 19 and 24 outlining, the conditions in use under which, and only under which, the explosive or blasting device is permissible. In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 19 and condition 2 on page 24. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.

Jan 1, 1940

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state, Adsorbed gas is stored in the micropore structure and its transport is governed by Fick's law. The free gas occurs in the. fracture system and flows according to Darcy's law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds.

Jan 1, 1969

By Charles Findlay, Stephen Krickovic, J. E. Carpetta

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors' experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982

By Gary L. Mowrey, William D. Monaghan, George F. Persetic, Gregory M. Molinda

Ground penetrating radar (GPR) has been investigated by the U.S. Bureau of Mines Pittsburgh Research Center for its potential to determine rod hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth to determine the value of GPR for roof hazard detection. The resolution of the current systems allows detection of gross roof fractures (>6A mm (>0.25 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologics changes in the roof. Differences in data quality are discussed, as well as suggestion for collecting improved data.

Jan 1, 1996

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and 2-year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 1, 2004

To cost-effectively reduce noise and vibration in newly manufactured mantrip vehicles. Approach Previous Bureau of Mines research demonstrated that noise controls could be in-stalled on existing mantrip vehicles, thereby substantially lowering noise levels inside the mantrip. Under Bureau sponsorship, a manufacturer of mantrip vehicles agreed to incorporate similar noise controls into a new vehicle during manufacture. Throughout this project, durability, maintainability, and cost were considered to be as important as noise reduction. How It Works The following noise-control features were included in the new mantrip: (a) Suspension Isolation- The suspension components were isolated by inserting elastomeric materials between them and the vehicle frame.

Jan 1, 1982

By James R. Aggson

The theoretical relationships that are used to calculate in situ rock stress magnitudes and directions from borehole deformation data obtained during overcoring are based on the assumption that the rock is a linearly elastic material. Strictly speaking, this assumption is not valid in any rock. Thus, investigators using overcoring techniques must either accept various degrees of nonlinearity and the associated inaccuracies or use core testing techniques that address the problem and compensate for elastic nonlinearity. Previously developed test procedures for stress-relief overcores partially correct for nonlinearity. This Bureau of Mines paper describes a test procedure that completely corrects for elastic nonlinearity in stress-relief overcores.

Jan 1, 1977

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By P. G. Pigott

This investigation by the Bureau of Mines demonstrated that building bricks can be produced by the steam-curing process from various types of industrial mineral wastes. Wastes, utilized to produce bricks, consisted of copper mill tailings, roofing granule fines, asbestos fines, and zinc mill tailings. Bonding of the wastes with either Ca(OH)2 or portland cement resulted in building bricks that met ASTM specification C73-67 for grade SW and MW bricks when evaluated in accordance with ASTM designation C67-66 on sampling and testing of brick. An economic evaluation of the process indicates the total operating cost per 1,000 bricks is about $36.

Jan 1, 1974

By B. E. Davis

As part of its program to increase the domestic availability of critical minerals, the Bureau of Mines conducted characterization and beneficiation studies on a St. Johns County, Fla., phosphate ore that was mined by borehole mining. Results revealed that the ore from this test mine was mostly sand-size carbonate-fluorapatite and quartz and contained 24.6 percent P205. Concentration by various flotation techniques produced phosphate concentrates that ranged, in percent, from 30.0 to 31.4 P205, 0.73 to 0.80 MgO, and 2.8 to 7.2 acid insoluble. Recovery of the phosphate from the ore ranged from 89.4 to 96.3 percent.

Jan 1, 1982

By H. R. Grau

NIOSH’s Pittsburgh Research Laboratory is currently involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration (MSHA) compliance dust sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels, and controls being used. A summary of the mining operations, sampling procedures, resulting data, and suggested methods to improve the dust control will be provided.

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system’s design philosophy, hardware and software components, examples of installations, and a few observational results.

By J. M. Gomes

The Bureau of Mines has investigated the occurrence and recovery of by-product heavy minerals from sand and gravel operations as a means of assessing the Nation's resources. Sand samples from 63 locations in central and southern California were treated to yield heavy-mineral concentrates. The mineral compositions of the concentrates were characterized by chemical and mineralogical examinations. Additional large quantities of concentrates were prepared from selected deposits that contained significant quantities. Beneficiation studies were performed on these concentrates to recover individual mineral products. Gold was recovered by amalgamation; platinum-group metals and radioactive minerals by flotation; magnetite, ilmenite, and chromite by magnetic and high-tension separation techniques.

Jan 1, 1980

By L. J. Froisland

An integrated process for recovering metal from nonmagnetic auto-shredder reject scrap was investigated by the Federal Bureau of Mines. The methods used were air classification, water elutriation, screening, magnetic separation, handpicking, and heavy-media separation. Metal recoveries in this process were projected at 39 percent copper and copper alloys, 53 percent aluminum, 96 percent iron, and 98 percent zinc die cast. An economic evaluation of the conceptual process indicated that a facility designed to reclaim the reject scrap from 200 shredded automobiles daily could be profitable. Total investment in this plant was estimated at $321,000; the discounted rate of return before taxes was 53 percent.

Jan 1, 1975

By S. P. Sandoval, A. E. Clark, S. W. Yopps, J. S. Gomer

The U.S. Bureau of Mines conducted Cu exchange tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the Cu exchange capacity as a function of Cu concentration, pH, and temperature. Using these equations, an analysis was made of the impact each clay could have on overall Cu recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of Cu from in situ leaching solutions.

Jan 1, 1992

By Edward D. Thimons, Jay F. Colinet

NIOSH conducted a strategic planning effort to identify those areas in mining with the greatest research needs. Data analysis and stakeholder input identified the need to reduce worker exposure to respirable crystalline silica dust as a high priority area. MSHA dust sampling data were analyzed to target the mining commodities and occupations with the greatest percentage of samples containing silica above compliance levels. In response, the Pittsburgh Research Laboratory (PRL) has implemented a multi-faceted research program to improve silica dust control for these problematic commodities and occupations. A review of silica compliance trends, PRL silica research programs, and recent control technology developments are provided here.