Search Documents

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By David R. Hanson

Transient electrical noise events pose serious problems for data acquisition systems used in monitoring acoustic emissions in laboratory and field environments. The U.S. Bureau of Mines has designed and constructed a trigger discriminator circuit for use in ultrasonic acoustic emission studies. Designed for use with signals in the frequency range of 50 to 400 kHz, the instrument examines .incoming signals for frequency content, amplitude, simultaneity, threshold crossings, and number of channels above threshold. If preselected criteria on these properties are met, a plus 5-V pulse is output that may be used to trigger a data acquisition system, allowing rejection of noise events that do not possess useful information. The system was designed for four input channels, but may be expanded to more channels with minimal design changes.

Jan 1, 1995

By P. A. Wasson, M. M. Fine

Roasting research involving small , batch experiments was conducted to explore the use of solid reductants for converting nonmagnetic iron ore to a magnetic type . Three typical Minnesota ores were tested with one or more of the following reductants : Lignite , lignite chars , anthracite , bituminous coal , petroleum coke , peat , and pyrite . Reductive roasting was accomplished in a 3- by 4- inch externally heated rotating drum . Ore and reductant were placed in the drum and heated to a desired temperature , which was maintained for a predetermined period . Recoveries of over 90 percent of the iron in magnetic concentrates were achieved at 650 ° C , using lignite , some lignite chars , a high- volatile bituminous coal , peat , and pyrite . Pyrite is a novel reductant , which is superior to carbonaceous materials other than lignite and some chars .

Jan 1, 1963

Dry weather since the third week in January has set back any prospects for an early increase in hydroelectric power in the Pacific Northwest, according to The Bonneville Power Administration. The 25% cutback made in July probably will not be restored in March or April. Noranda Aluminum, Inc., increased its price for 99.5% aluminum ingot from 66 cents to 70 cents per pound effective March 1, 1980. Revere Copper & Brass, Inc., also -increased its price for primary aluminum from 66.0 cents to 70.0 cents per pound effective February 1. Kaiser Aluminum & Chemical Corp. raised its international price for 99.5% primary aluminum from 72.6 cents to 82.6 cents per pound, c. i. f., effective February 26 on new orders and on shipments from March 15.

Jan 1, 1980

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By N. H. Coates

A small, special-purpose centrifugal compressor was developed to circulate 60 pounds per hour of helium at 1,000° F and 250 psig because standard, commercial units were not available. Performance characteristics of this compressor were determined at helium flows of 2,000 to 18,000 std cu ft per hour, pressures of 100 to 250 psig, and temperatures of 100° to 1,000° F. This range is 2 to 90 actual cu ft per minute. Several graphs show the adiabatic head developed by the compressor over this wide flow range at various combinations of temperature and pressure. A compressor performance map relates pressure ratio to mass flow, temperature, pressure, and speed. This map can be used to accurately predict compressor performance factors within the range of operating conditions covered by the experiments.

Jan 1, 1963

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972

By L. W. Higley

Procedures were developed for reclaiming high-temperature alloy scrap in the form of standard cobalt-base alloy. A cobalt-base, multicomponent, high- temperature alloy, such as S-816, can be successfully melted from scrap, and its specified chemical composition can be retained. Induction furnace melting in a controlled atmosphere was used to obtain ingots that were subsequently fabricated by impact forging to provide specimens for heat treatment and testing. Of the numerous metal elements in S-816 alloy, only small quantities of molybdenum were lost in the melting operation as finally developed. Test results indicated that the scrap material, after melting, forging, and heat treatment, was equivalent in room-temperature tensile strength, in high-temperature creep and stress-rupture properties, and in chemical composition to commercially produced S-816 alloy made from virgin material.

Jan 1, 1963

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By John F. Papp

International and U.S. chromium material flow, losses, and environmental releases and transfers from mining through industrial processing, end use, and recycling are identified and quantified. Average (1983-92) U.S. consumption has been: metallurgical industry, 87 pct; chemical industry, 10 pet; and refractory industry, 3 pct. Average chromium content of aluminum, cobalt, copper, nickel, and titanium alloys and alloy, carbon, and stainless steel alloys was estimated. Anthropogenic chromium consumption was estimated for the cement and copper industries. N on-commodity cycle anthropogenic chromium mobilization resulting from U.S. fuel and fertilizer use was estimated. Commodity cycle anthropogenic world chromium loss from mining and primary consumer industry was estimated to be equivalent to about 56 pct of chromium contained in chromite ore production and represented a loss rate of 181 kt-Cr/Mt-CrOre. Chromium released to the atmosphere from natural and from anthropogenic sources were comparable in magnitude. Chromium released to soil was mostly from anthropogenic sources, and aquatic releases were all anthropogenic. Domestic product chromium losses exceed process losses by more than a factor of 10 showing the importance and potential environmental impact of post-consumer recycling. The location of historical and current domestic chromium industry processing sites in 23 States were reported. Chromium releases and transfers to the environment were estimated from 1973 through 2002 by primary consumer industry. A decrease in chromium releases and transfers to the environment was anticipated.

Jan 1, 1995

By Gary M. Larwood

A study was conducted to determine the amount of transportation equipment required to move 1.2 billion tons of coal in 1985. The Federal Bureau of Mines has investigated a majority of the various practices associated with coal transportation and has gathered information on the regional origin-destination patterns, methods of movement, equipment stocks, rate structures, and operational capacities of the most important modes of coal haulage currently in use. Models employing this information were developed to establish the origin-destination pattern for 1985 coal shipments, estimate practical tonnage capacities for selected coal hauling rivers, develop modal shares for both unconstrained (by river capacity) and constrained cases, and present a range of coal transportation equipment requirements for given sets of constraints. Projected transportation shares for rail ranged from 63.7 to 72.3 percent, and for river, from 8.8 to 16.4 percent. Other coal transportation modes (truck, conveyor, Great Lakes, and tidewater) are expected to retain their historic shares of coal traffic. Equipment estimates were made for 1985 rail and water transportation based on 1973 average and best practice. Average practice estimates ranged from 675,000 to 710,000 hopper cars (100-ton) and 3,100 to 5,940 barges (1,400-ton equivalent). Best practice estimates ranged from 126,000 to 142,000 hopper cars and 1,750 to 3,450 barges. Full implementation of 1973 best practice by 1985 is unlikely.

Jan 1, 1976

By J. M. Stuve

Low-temperature heat capacities of chiolite (Na5Al3F14) were determined by adiabatic calorimetry in the temperature range 5.8 to 300 K. The derived standard entropy (S°, 298.15) was 115.6 ± 0.2 cal/deg-mole. High temperature enthalpies relative to 298.15 K were obtained by precision drop calorimetry up to 1,000 K. Tables of experimental data and related thermodynamic functions are given for the temperature range of experimental observations.

Jan 1, 1980

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By Floyd G. Anderson

A study was made of the effectiveness of dust-control methods being employed in connection with continuous-mining operations. Airborne dust exposures of workmen and dust loadings of return air were determined for six types of continuous-mining machines. The conditions required for control of dust exposure are summarized and include ventilation of the working face by an exhaust system. Return-air dust loadings ranging up to 13 pounds per hour are reported.

Jan 1, 1963

By B. J. Scheiner

Silver ores from the Candelaria District, Nevada, and Round Mountain District, Colorado, were investigated mineralogically and metallurgically. Silver minerals of four distinct groups were identified: (1) silver sulfide; (2) argentojarosite; (3) silver contained in the iron oxide; and (4) manganese carbonate-oxide minerals, Electrooxidation and acid-chloride leaching techniques were investigated as means of altering silver minerals, and their effects on subsequent silver extraction were determined. Application of the knowledge obtained from mineral leaching studies resulted in development of a sulfur dioxide-sodium chloride leaching sequence for extracting silver from these types of ores. Silver extractions of 80 to 85 percent were obtained by leaching the ores with a sulfurous acid-sodium chloride system. This was an increase of 9 to 61 percent silver extraction over that obtained by conventional cyanidation techniques.

Jan 1, 1973

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By D. E. Kirby

In the preparation of beryllium-copper alloys by fused-salt electrolysis, beryllium was electrowon from beryllium oxide dissolved in fluoride electrolytes and deposited on copper cathodes. At 880° to 1,030° C, deposition was on solid cathodes. Beryllium deposited on the copper, forming a liquid alloy that dripped from the cathode. Dripping alloys containing 3 to 4 weight-percent beryllium were produced with as high as 90 percent cathode current efficiency, by electrolysis at 910°.C. To prepare alloys of higher beryllium content, attempts were made at depositing beryllium on liquid copper cathodes. These efforts were generally unsuccessful, although alloys containing as much as 12 percent beryllium were prepared by this method. At temperatures of 1,100° to 1,300° C, requisite to maintaining beryllium-copper compositions as liquids, the beryllium reacted with cell structures.

Jan 1, 1972

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupation-al Research Agenda, problems created by occupational hearing loss include(1) reduced quality of life due to social isolation and unrelenting tinnitus,(2) impaired communication with family members, the public, and coworkers, (3) diminished ability to monitor the work environment (i.e., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers? compensation and hearing aids.

Jan 1, 2001

By E. M. Murphy

Comparative data from ASTM method of test E-162 and large-scale trials in the Experimental Mine show that the flame-spread quality of brattice cloth and other ventilation control materials can effectively be evaluated by either method. Materials having a flame spread index of 25 or less, as determined by the simpler and more economical laboratory test ASTM E-162, do not present a serious fire hazard when used in coal mines.

Jan 1, 1972

Most laboratory sealant studies were carried out in 2.0 inch I.D. Plexiglas tubes of 9.0 inches height containing 4.0 to 4.5 inches reconstructed soil from an 0-8 or 8-16 inch soil horizon at the Lanse site. (When soil was used from the Kato site, the top soil horizon was approximately 0-4 inches. The 4-8 inch horizon was somewhat comparable to the Lanse 8-16 inch horizon.) A 20 mesh Saran or steel screen was placed over the rubber stopper with a bottom drain to a 100 ml measuring cylinder. In some earlier experiments a 1/2 inch bed of 1/4 inch pea-gravel was then added, but in later experiments this was eliminated as it showed no particular utility. Field soil samples collected by a shovel were stored in sealed containers and sieved through a 4 mesh screen just before use. (Moisture content was typically about 25% for A horizon soil and about 20% for B horizon soil.) The sieved soil minus roots was then added in increments of about 1 1/4 inches. Compaction was effected by dropping a weighted ramrod (1-7/8 inches O.D,) five times from a height of two inches. If about twenty tamps were used or if the soil columns were rapped vigorously while water-logged, compaction was high with no detectable percolation. Freezing such samples would then usually cause very slow percolation, e.g. 1-2 ml/day. Using this as a standard procedure, percolation flows were usually stablized after two to three days to rates of about 100 to 200 ml/hour. Percolate was recycled carefully to minimize disturbance of the soil surface. When percolation flows were about 100 to 200 ml/hour, various additives (sealants) were introduced to the moist column in two to three increments to maintain a slight head. Additive concentrations were usually 2-1/2% with some at 5% in earlier experiments. Typical use of 40 ml of 2-1/2% additive corresponds to 4400 lbs/acre. When no more additive was present as supernatent liquid, water washes of about 15 ml were then used several times followed by special additives as needed. More water washes were then used to maintain a head of about 1/2 inch. Percolate was collected in 100 ml cylinders to measure percolation rates in ml/hr. Turbid percolate was evaporated to determine amount of eluted latex. Percolate was sometimes checked for pH by Pan-pH Indicator Paper9,10 reading in 0.5 units. Surface tension measurements were sometimes made by a DuNouy tensiometer10 in experiments using a surfactant for pretreatment.

Jan 1, 1972