Search Documents

The objective is to provide effective training on refuge chambers for underground coal miners. This training will increase knowledge about how to teach miners to operate, transport, and inspect a refuge chamber; what to expect psychologically and physiologically inside a refuge chamber; and how to decide when to use a refuge chamber. Background During 2006?2007, several disasters occurred at U.S. underground coal mines, resulting in 28 fatalities. These disasters led to new approaches to mine safety and health, as well as new federal regulations. One new technology mandated by federal legislation is the refuge chamber. Refuge chambers are movable shelters that are either made of steel or inflate from a steel skid as a tent. They can potentially save the lives of miners during an underground mine emergency by providing breathable air, food, water, and a safe environment for up to 96 hours. Because the refuge chamber is a new technology, recommendations, information, and training products are greatly needed.

Nov 1, 2009

By Gerald T. Homce, Michael R. Yenchek, H. Kenneth Sacks, James C. Cawley

Abstract—Overhead electric power lines present a serious electrocution hazard to personnel in a variety of industries. Overhead lines, typically uninsulated conductors supported on towers or poles, are the most common means of electric power transmission and distribution, and are exposed to contact by mobile equipment such as cranes and trucks. Equipment contacting energized overhead lines becomes elevated to a high voltage, and simultaneous contact by personnel of the “hot” frame and ground can cause serious electrical shock and burns. Industries where risk of these accidents is greatest include construction, mining, agriculture, and communications/public utilities. An estimated 2300 accidental overhead line contacts occur each year in the U.S. This paper describes a practical low-cost concept to detect actual contact of mobile equipment with a high-voltage line and provide a warning. Accident statistics indicate that more than half of the fatalities could be prevented by such a device. Index Terms—Crane, electrical shock prevention, engineering control, mining, mobile equipment, power line.

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982

By Samuel R. M. Burton

This Bureau of Mines report describes a method for determining parts per million (ppm) of helium-4 (He-4) in helium-3 (He-3) to an accuracy of ±5% by mass spectrometry. Gravimetrically prepared primary standards were used for the calibration of a Dempster 1800 magnetic sector mass spectrometer. A comparison between a 2.49% He-4 in hydrogen mixture and a 2.49% He-4 in He-3 mixture shows that He-3 can be replaced with hydrogen as a diluent for standards with comparable mass spectrometry sensitivities for He-4. Using hydrogen as a diluent allows analysis of He-3 samples for He-4 when He-3 for preparation of standards is not available and also conserves the rare He-3 isotope. Standards of He-4 in Hz were prepared for calibration of the mass spectrometer for quantitative determinations of He-4 in the 2-to 100-ppm range. A minimum detectable limit of 2 ppm He-4 is obtained by this method.

Jan 1, 1989

By P. D. Laverty

The U.S. Bureau of Mines treated mixed and contaminated super alloy scrap by pyrometallurgical and hydrometallurgical methods to separate and recover metal values. Best results were obtained by leaching Zn-treated or atomized scrap with HCI-02 at 9SO C and 50 psig 02' This resulted in dissolving approxi-mately 98 pet of the AI, Co, Cr, Cu, Fe, Mn, Ni, and Zn while rejecting over 98 pct of the Mo, Nb, Ta, Ti, W, and Zr as an insoluble refractory residue. Chlorine was successfully substituted for HCI to leach Zn-treated scrap but was unsuccessful for leaching atomized scrap. The leaching solution was treated by pH adjustment and hydrothermal precipitation at 2000 C for 4 h to remove AI, Cr, Fe, and other contaminants as a filterable precipitate. Recovery of Co and Ni would be accomplished by solvent extraction and e1ectrowinning. Chromium recovery as a ferroalloy was demonstrated.

Jan 1, 1989

Provide sound battery safety guidelines for mine workers who maintain mobile surface mining equipment. Approach Battery-related accidents account for about 5 percent of all nonfatal disabling injuries in coal and metal nonmetal surface mines. These accidents occur despite the fact that appropriate battery safety technology (maintenance-free batteries, cable removers, fault detectors, hot-jumping systems, etc.) exists. Mine operators are not always aware of the safety measures that could be taken because this safety information is widely scattered in numerous unrelated technical reports, vendor brochures, and journal articles. A literature search of these reports and a review of relevant industry standards, handbooks, and references on battery safety, followed by discussions with mining company and MSHA personnel, provided the Bureau of Mines with the background necessary to develop procedures for proper and safe battery usage. These procedures were condensed and written in nontechnical language to serve as guidelines in assuring battery safety during maintenance of mining equipment.

Jan 1, 1986

Develop personal computer (PC) based software for analyzing and/or filtering time- and frequency-domain attributes of seismic and electromagnetic signals from geophysical surveys for the enhanced interpretation of rock masses and subsurface geologic structure. The Problem Both mining and petroleum geophysicists utilize seismic signals to characterize rock masses for delineating subsurface stratigraphy and structural conditions. However, a vast amount of information available in seismic project evaluation data often is unavailable for interpretation unless these data are enhanced. New processing technology increases the quality of these signals for analysis and interpretation. Comprehensive signal processing software is mostly written for petroleum exploration companies. Commercially available signal processing programs are often limited to a single application or are restricted for use with specific hardware, e.g., a digital oscilloscope or a mainframe computer. The programs may use computer codes that are proprietary, restrict user modification to expand capabilities, or may be hard to interface. They may have insufficient documentation for easy use and be support dependent.

Jan 1, 1990

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By James R. Means, George Bowser

A new phone system was developed that provides eight full duplex communications channels over a single twisted shielded phone line, with no central switching station or line amplifiers. This system greatly simplifies installation and maintenance over that required with conventional switching systems. The system is based on microprocessor technology and digital frequency synthesis. Frequency division multiplexing is used over a bandwidth of approximately 300 kHz, and a baseband voice channel (compatible with conventional pager phones) is provided as a backup to assure communication if the multiplex features fail. Multiplex operations are controlled over a 30-kHz digital channel. The system is designed to operate with up to 16 km (10 miles) of cable plant and a maximum phone separation of 8 km (5 miles). The digital techniques permit a limited amount of monitoring and control capability to each phone. This consists of two pair of contact inputs or outputs, to be used as desired. These "flags" may be read or controlled by a dispatcher's phone.

By Jürgen F. Brune, William H. Schiffbauer

Communication problems are not new. Research in this area goes back as far as 7922 when the US Bureau of Mines performed experiments to detect radio signals from inside their experimental mine in Bruceton, Pennsylvania. Many improvements to mine communications have been made over the years but for any number of reasons the underground coal mining industry has been behind in implementing advances. Present communications systems far underground mines can be hard-wired or wireless. Both types of systems can fail when faced with fires, roof falls, explosions, and power or battery failure. Currently installed wireless communications systems usually employ a special antenna cable called a "leaky feeder" Fiber optic cables are also used in some applications to form a "backbone" for wireless transceivers. Through-the-earth (TTE) and wireless radio systems are less common. Except for TTE systems, most wireless systems require some wire-bound components, which are susceptible to failure during disasters as cable breakage interrupts communications.

By L. J. Froisland

The Bureau of Mines conducted a 4-year research program at Uravan, Colo., on a 2-1/2-acre reclamation plot on the slope of a uranium tailings pile that had been covered with mine waste rock. The purpose of this study was to determine the effects of plant species, type of irrigation, type of fertilizers, and use of dust control chemicals on plant growth and surface coverage. Best grass coverage, nearly 100 percent with 240 plants per square foot, was developed in a section that was seeded with crested wheatgrass, fertilized with sewage sludge, and sprinkler irrigated. For comparison, a section that had been treated with commercial fertilizers developed 3.1 crested wheatgrass plants per square foot and 24 percent coverage without irrigation, and 8 plants per square foot and 75 percent coverage with irrigation. Results of spraying a dust control chemical were inconclusive. Russian-thistle invaded all test sections and ranged in density from 0.6 to 7.3 plants per square foot.

Jan 1, 1982

By S. H. Katz, J. J. Bloomfield

Fires in zinc dust have sometimes given particular trouble owing to their resistance to extinguishers and the liability of explosions . Similar problems , notably with aluminum dust* , have previously been subjects of investigation by the Bureau of Mines .

Mar 1, 1922

By E. G. King, W. W. Weller

Low- temperature heat capacity measurements of muscovite were made in the temperature range from 50° to 298 ° K. The entropy at 298.15 ° K was evaluated as S298.15 = 69.0 ± 0.7 cal /deg mole .

Jul 1, 1960

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By John F. McCoy

The U.S. Bureau of Mines (USBM) awarded? a contract to Foster-Miller, Inc. to develop guidelines for designing, constructing, stocking, and maintaining rescue chambers in underground mines. This report develops information and recommendations which could be used by a mine operator who desired to install a rescue chamber. Volume I covers the following major areas: atmospheric life support, configuration and construction, chamber location, power and lighting, equipment and supplies, communications, and psychological aspects and training. Volume II contains the following appendices: History of Barricading, Chamber Pressuriztion Considerations, Diffusional Infiltration of Gas, Compressed Air Storage, Location Examples, and Psychological Aspects.

Jan 1, 1983

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960

By L. J. Kane

Applications are described of various methods for determining the weight concentration and physical properties of solid and liquid impurities of gases in connection with problems encountered in synthesis-gas production. Of special interest among these methods may be listed: 1. A method developed for determining, the weight concentration of solid and liquid impurities in. hot, crude synthesis gas containing a high concentration of moisture. 2. A method developed for the same purpose but for highly purified synthesis gas or atmospheric air. 3. A method for obtaining a uniform dispersion of dry duet or, a microscope slide for particle-size determination or other purposes.

Jan 1, 1954

By Stephen M. Jasinski

The development and industry adaptation of advanced technologies have led to many important uses for bismuth and its compounds. Bismuth-base alloys are essential for manufacturing jet engine turbine blades, lenses, and various safety devices, such as fire-protection sprinklers. The addition of bismuth to iron, steel, and aluminum imparts properties to these metals that makes them useful in diversified applications. Bismuth is also used widely in medicine, pigments, and electronics. The United States relies heavily upon imports from South America and Europe to meet its demand for bismuth, which is recovered chiefly as a byproduct of lead processing.

Jan 1, 1992

By Martin H. Stanczyk

Acid leaching of selected copper sulfide minerals, impure copper sulfide flotation concentrates, and a cement copper precipitate at elevated temperatures and pressures was investigated. Copper extractions of 97 to 99 pct were obtained by leaching chalcopyrite and the flotation concentrates with water under oxidizing conditions at 200° C for 30 to 60 min. In tests with bornite, chalcocite,and cement copper, addition of sulfuric acid or pyrite to the autoclave was required to obtain similar copper extractions. The chemistry of leaching copper minerals was studied. It was determined that different copper sulfides altered to covellite as one step in their dissolution.

Jan 1, 1963

By J. Baicker

A two-inch diameter probe containing an intrinsic germanium detector, a canister-type solid cryogen cooling system, cooled FET preamplifier, linear amplifier, high voltage supply, analog-digital converter, microprocessor, buffer memory, bidirectional cable link, and all power supplies has been designed, assembled and tested. A surface support vehicle was designed, built and outfitted. A mini-computer system was constructed and preliminary software developed and tested. A special handling system for a Cf-252 neutron source was designed and has been ordered. The entire system (less the neutron source) is ready for its first field tests. Lab description of the system is presented.

Jan 1, 1978