Search Documents

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

On a continuous miner coal face methane concentrations are affected by the quantity of fresh intake air reaching the face. When mining the box cut on a 12.2-m (40-ft) two-pass extended cut face, the continuous miner is always at the point of deepest penetration, and operation of the machine-mounted dust scrubber and water spray system improve the flow of fresh air to the end of the box cut. However, when the continuous miner leaves the box cut to begin cutting the 40-ft slab, little is known about how much ventilation air reaches the end of the box cut. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health conducted a full-scale study to answer this question. Tests were run to determine how much ventilation air reaches the end of the box cut with the continuous miner at three locations in the 40-fttwo-pass extended cut mining sequence; at the end of the 40-ft box cut, at the start of the 40-ft slab cut, and 6.1 m (20 ft) into the slab cut. During these tests, methane gas was uniformly released at the end of the 40-ft box cut. Methane concentrations measured0.3 m (1 ft) from the roof and face of the box cut were used to estimate face airflow quantities. Fresh air flow rates of 1.89and 4.72 m/sec (4,000 and 10.000 cfm), scrubber flow rates of 0, 4,000 and 10,000 cfm, water spray pressures of 0 and3827 kPa (0 and 120 psi), and a blowing curtain setback position of 15.2m (50 ft) were used during these tests. To improve ventilation to the end of the 40-ft box cut when the continuous miner was starting the 40-ft slab cut and 20 ft into the slab cut, the blowing curtain was advanced from its 50-ft setback to locations 40-ft and then 8.5 m (28 ft) from the face. KEYWORDS: Face ventilation, Extended cut, Methane, Box cut, Continuous miner, Scrubber

By C. H. McNaughton

The Tennessee Copper Co. operated two mines in the Ducktown district during 1928. The Burra Burra mine is much the larger operation and is the chief source of the ore smelted and treated in the, company's smelter and acid plant rat Copperhill, 4.5 miles from Ducktown. This mine operates steadily and furnishes a regular output of about 40,000 tons per month. The Eureka mine is operated irregularly and produces a much smaller tonnage of high-sulphur ore the rate of output depending upon the demand for sulphur. During 1928 about 60 per cent of the combined output of these mines was shipped directly to the smelter, and the balance was concentrated before shipment in the flotation plant located near the mines. ACKNOWLEDGMENTS The author acknowledges the assistance of Lamar Weaver, Assistant mine superintendent of the Tennessee Copper Co, and of C. F. Jackson, mining engineer, U. S. Bureau of Mines, in the, preparation of this paper, U. S. Geological Survey Professional-Paper 139, by W. H. Emmons and F. B. Laney, has been drawn upon for information contained 'in the paragraphs on history and geology.

Jan 1, 1929

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964

By J. A. Herdlick

The Star mine, near Neihart, Cascade County, Mont., has been in continuous operation since the construction of a 50-ton bulk flotation mill in 1939. The mine was examined by G. N. Bennett, an engineer of the Bureau of Mines, in November 1942. At that time the life of the operation appeared to be limited and a program of crosscutting and core drilling were recommended. The program had as its objective the investigation of a promising undeveloped area lying west of the Star vein and, if possible, the development of enough reserves in this area to insure continuous operation during the war emergency. Development of additional reserves would then justify necessary changes in the mill in order to eliminate the heavy penalties imposed for excess zinc in the bulk concentrates. The Bureau of Mines work began in February 1944 and was completed in September 1944. The project was started by Wilder R. Brinton and continued by Thomas W. Oster, mining engineers in the Bureau's Montana district office. Beneficiation tests on are and concentrates were made after completion of the underground work. This report presents the factual data obtained during all phases of the Bureau's investigation.

Jan 1, 1949

By George A. Burrell, Frank M. Seibert

The Bureau of Mines, as part of its designated duty of investigating the causes of mine accidents, is conducting at its experiment station in Pittsburgh, Pa., a study of mine gases. Some of the work already done in connection with this study is outlined below. A large number of mine-gas samples have been collected under normal conditions in returns and in splits, and at other points in the ventilating current, also at the face, in the goave or gob, in unventilated places, and wherever the air was still. Samples have also been obtained under abnormal conditions, as after explosions and while mine fires were in progress, or from sealed areas behind stoppings and darns where the air had been stagnant for some time. Chemical changes in the composition of mine atmospheres during mine fires have been studied," and conditions peculiar to certain mines have been investigated. The question of the effect of a change in atmospheric pressure on the escape of gas (methane) in coal mines has been studied. Explosives have been fired in both coal and metal mines, and samples of resulting gases have been collected to ascertain the degree to which these gases vitiate the air. A series of samples in mines where gasoline locomotives were being used have been examined in order to ascertain the degree to which the exhaust gases from such locomotives foul the mine air. Experiments have also been performed in regard to the relative effect of carbon monoxide b upon men and small animals. A preliminary report relating to the inflammable gases in mine air has been published. Full reports of the results of the investigations outlined above will be published as soon as all the necessary data have been gathered. The first part of this report deals with the methods used by the bureau in the collection and examination of the various mine gases; the latter part discusses the bureau's methods of sampling and examining natural gas.

Jan 1, 1913

By Wilbur I. Duvall, S. L. Windes, Leonard Obert

"Previous investigations, too numerous to be listed in entirety, have been performed to determine the physical properties of rock. When considered according to their objectives, most of these investigations can be grouped as follows: First, the geologic group (1,2),4/ in which the purpose was to obtain information on the physical properties of the rocks that make up the earth's crust. Particular emphasis has been placed on the determination of the elastic constants--that is, Young's modulus, the modules of rigidity, and Poisson's ratio – as these quantities determine the propagation characteristics of seismic waves. Second, the structural properties group (3 - 11), in which the physical properties of architectural or monumental stone, concrete and aggregate rock, road blocks (cobblestone), and the like were desired. The tests have been quite general and include, besides the elastic properties; the compressive and tensile strength, and the toughness, hardness, and weathering properties of many types of rocks.To .a lesser degree, investigations have been carried out to determine the physical properties of mine rock. A few reports (12 - 14) present data on the crushability and grindability of mine rock, and a large number of papers discuss grinding and crushing procedures and methods of analyzing the data (for example, see references 15 - 17). Some of the latter group also have given the results of tests on mine rock; however, comparatively few include an adequate petrographic description or information on other physical properties of the rock. A few papers,(18 - 22) have reported studies of the strength of rock specimens in respect to the strength of parts of mine structures, such as pillars, roof, arches, etc. Other papers (23 - 26) have discussed investigations on such subjects as primary and secondary crushing, diamond and pneumatic rock drilling, explosive breaking and shattering of rock, rate of drifting and miring, and other allied problems. The majority of these reports have given no more than a cursory, description of the rocks and have included no statement regarding the physical properties. When statements have been given regarding the physical properties, they have usually referred only to isolated tests, making correlations between variations in the physical properties and variations in the .test under consideration difficult, if not impossible. Some reports have included handbook values on such characteristics as the crushing strength, hardness, and toughness. This practice is not satisfactory, because these values are usually given for col¬lective types of rocks, such as granites, limestones, and marbles, and it is known that the variations of the physical properties within these groups is often larger than the differences between the groups."

Aug 1, 1946

By T. J. Ballard

The Tallapoosa Copper mine in Haralson County, Ga., has been operated, or under development at various times since before the Civil War. The geology of the deposit is similar to that of many of the pyrite deposits occurring in the belt of ancient crystalline and metamorphic rocks that extends diagonally northeast-southwest across the State. The Bureau of Mines, in its program of investigation of, strategic mineral deposits, diamond-drilled four holes totaling 1,570.3 feet at the deposit during the period June to September 1947 to verify the old drill records and the continuation of the deposit at depth.

Jan 1, 1948

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

By H. M. Lawrence

"In the land-pebble district of Florida a lively interest in the possibilities of obtaining increased recoveries of phosphate rock is evident. Research in several directions is being carried on by companies operating in the district to increase the yields obtained by the washing plants. The Bureau of Mines is cooperating with this research program to promote more efficient plant practice and to avoid unnecessary depletion of mineral resources.Washing practice, as carried on in the district at present for the recover of phosphate rock from the crude ores or matrix, is not a complicated process. Flow sheets of the several companies are similar, although the equipment varies with the preferences of the individual operators. For disintegrating the matrix log washers are favored, although revolving drums equipped with flights to break up lumps of clay are also used. Fine sand is removed by screening. Vibrating screens have become well established in the district, although stationary flat screens and trammels are also employed.The writer acknowledges with appreciation the cooperation of the phosphate companies in the land-pebble district; suggestions and criticism by Will. H. Coghill, supervising engineer, Ore Dressing Section of the Bureau of Mines; and the laboratory assistance of J. O. Davie, J. W. Pamplin, and E. Roca, cooperative fellows of the University of Alabama.Losses in the Finer SizesOf the phosphate that is not recovered by present washing methods the greater portion is in the finer sizes. In these sizes the phosphate grains are accompanied by grains of sand - largely quartz - of the same size, and recovery of these phosphate grains as a commercial product is not possible by simple washing methods. Phosphate recoveries approaching complete extraction can only be effecte by applying metallurgical processes, either mechanical or chemical. As yet, most of these processes have not advanced much beyond the laboratory or perhaps the pilot-plant stage. Such processes may have some application to the beneficiation of phosphatic ores or washer rejects, but a discussion of them is not within the scope of this paper."

Apr 1, 1929

By R. D. Currie

A study of the accident statistics in the coal mining industry convinces one that an organized effort must be put forth to prevent the vast destruction of human life in this industry . The fatality rate in Pennsylvania has not improved in the past several years and during 1928 it was higher than the average for the period 1916 to 1927 , inclusive . Although the accident rate for this State is less than that of the coal mines of the United States as a whole , nevertheless the rate is unduly high ; however , there are many companies which have exceptionally good records as regards both fatal and nonfatal accidents . A study of the methods used by some of these relatively good- record companies to reduce accidents in their mines shows that they exert an organized effort to prevent accidents , and that their safety organizations usually affect every employee in and about the mine from the highest official to the check boy . The chief executive must be actively and personally interested in accident prevention if real safety results are to be obtained ; when he shows this interest it is almost invariably reflected in the officials under him and throughout the organization . Safety organizations vary in form and are readily changed or adapted to the varying conditions found in the bituminous field . The companies whose organizations were studied in preparing this report are all getting good results , and it is their opinion that the safety organizations have been a big factor in obtaining these results . At their request the identity of some of the companies whose organizations were studied has not been divulged in this paper , but this does not affect the value of the information concerning their safety organizations .

Mar 1, 1931

By Jeffrey S. Walker

Abandoned underground mine openings are susceptible to collapse because of the mining methods used, the character of the overburden, and the typically large, wide entries with minimal roof support. The final effect of the collapse of the underground workings is surface subsidence. To reduce the probability of subsidence, methods to backfill the mine void with various types of materials have been developed. This U.S. Bureau of Mines report describes the available technologies for subsidence abatement and discusses their operation and application. The basis of these abatement methods is the replacement of the mined material with mine waste. Backfilling of mine voids is the most common method of stabilization used to abate subsidence and protect surface structures. Hydraulic flushing and grouting, using remote methods from single or multiple boreholes, are the most often-used methods for the placement of backfill material. Other subsidence abatement techniques are available and may be more appropriate under different conditions. These other techniques include pneumatic stowing, either by in-mine or remote methods, and various point support methods that do not completely fill the mine void and are used for the protection of small areas of the land surface and surface structures.

Jan 1, 1993

By C. C. Furnas

Despite the fact that a great many industrial processes depend on efficient contact between a gas stream and a bed of broken solids for their operation, the data in the literature are very meager. Several investigations3 have been undertaken, but the work has been limited in scope and application. BUREAU OF MINES PROGRAM OF RESEARCH For the past 10 years the United States Bureau of Mines has been engaged in research with the object of formulating a more or less complete quantitative theory of the workings of the iron blast furnace. Obviously, in order to do this one of the essentials is to have considerable definite information on the laws of gas flow through beds of broken solids. This report in a brief summary of the experimental work on the problem which has been done at the North Central Experiment Station. The complete report with more detailed tabulation of the data and explanations of the experimental procedure is in process of publication in the form of a bulletin.

Jan 1, 1928

By Oliver C. Ralston

The Nonmetallic Minerals Division of the Bureau of Mines deals with all mineral substances not intended to be used as ores for extraction of metals, with the exception of the fuels. However, coal washing, the methods of which are highly Similar to the concentrating methods for ores, is in¬cluded In the work of the Nonmetallic Minerals Division to facilitate administration and to avoid duplication of equipment. During the fiscal year most of the work of the division was done at the experiment stations in College Park, Md., Tuscaloosa, Ala., and Seattle, Wash.

Jan 1, 1938

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By John R. Reeves

The data presented in this paper form the chief part of a general survey of the oil-shale resources of Indiana. Other papers* have already been published which contain data an various aspects of this resource. In combination, these papers present data with reference to the following points; (1) distribution of the New Albany shale; (2) amount of shale available; (3) homogeneity and thickness of the formation; (4) amount and quality of the oil obtained from the shale; (5) nitrogen content of the shale; (6) extractibility of the shale and its amenity to breaking; (7) some economic factors bearing upon the utilization of the shale; and (3) other miscellaneous factors and data. In the future, technical work on other phases of the general problem is expected to be done with the object of making a complete survey of this resource which is of much potential importance to the state and nation.

Jan 1, 1923

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Western Middle field is part of the comprehensive study of the mine-water problem in the anthra¬cite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8,9,10,11,1,2,15,16).8 The Western Middle field is in Schuylkill, Columbia, and Northumberland Counties in eastern Pennsylvania. It has an area of 120 square miles, is 42 miles long from Delano on the east to Trevorton on the west, and is 2 to 5 miles wide. In the Western Middle field are 58 underground water pools containing 38 billion gallons of water (5). Some of the pools overflow to the surface, and the water from others seeps into adjacent mines through permeable barrier pillars separating them from abandoned mines. Several active mines are interconnected to workings in abandoned mines, which are partly filled with water. These mines are separated by barrier pillars that are considered effective only below the altitude of the connections. In some abandoned mines, pumping stations maintain the water at altitudes where the hydrostatic pressure against the barrier pillars is not excessive and does not endanger adjacent active mines. If water in these abandoned mines is allowed to rise to where it can overflow into the active mines, it must be pumped from the active mines at lower altitudes; this materially increases the cost of pumping. It is estimated that from 1944 to 1948 approximately 30 percent of the water pumped to the surface was from abandoned mines.

Jan 1, 1953