Search Documents

By Kenneth D. Winters

This Bureau of Mines report presents a Fortran IV computer program for the structural analysis of (1) protective canopies used in underground mines to protect equipment operators from roof falls and (2) rollover protective structures (ROPS) used in surface mines to protect equipment operators during vehicle overturn accidents. The program, entitled PLASTIC CANOPY, permits rapid and inexpensive calculation of the ultimate strength and deformation characteristics of a canopy for a variety of static loading conditions. The structure is modeled as a series of interconnected beam and/or plate elements. Stresses in, and displacements of, each structural element are computed and printed out at the yield strength of the canopy, at several intermediate load levels between the yield and ultimate strength of the canopy, and at the ultimate strength of the canopy. Other features of the program include prediction of buckling of a beam member under combined axial compression loading and bending, plotting of the input geometry of the structure, and plotting of the deformed shape of the loaded structure. Program description, input instructions, program listing, and four example problems are included.

Jan 1, 1979

By R. L. Rough

The Bureau of Mines analyzed rotary-coring-operations data to compare mud and air as coring mediums, and to compare core recoveries, penetration rates, and cost data for the respective mediums as part of an investigation of the susceptibility to secondary-recovery techniques of petroleum reservoirs in Ohio, Pennsylvania, and West Virginia. This report describes the rotary-diamond coring equipment and operations employed while coring 20 wells--10 cored using mud, and 10 cored using air. Data relevant to the draw works, rotary-table power, drill pipe, drill collars, core barrel, core head, mud pumps, or air compressors are tabulated. Average bit weight and rotary speed, core recovery, and penetration rates are listed for each formation cored. In general, core recoveries were better from the mud-cored wells, whereas penetration rates were faster for the air-cored wells. Coring costs were about the same for single-formation wells cored with either mud or air; however, costs increased considerably when multiple-formation wells were cored with air.

Jan 1, 1969

By T. A. Henrie

The Federal Bureau of Mines has investigated methods of sodium reduction of titanium chlorides to produce high purity titanium metal (14).4/ This investigation was made to obtain a better understanding of the reactions involved in sodium reduction of titanium chlorides and was part of the Bureau's activities toward improving the technology of titanium. Theoretical and experimental evidence show that sodium reduction of titanium tetrachloride occurs by stepwise reactions. The first stage reduction between sodium vapor and vapors of titanium chlorides produces titanium di-and trichlorides which subsequently condense with sodium chloride to form a salt mixture. The second stage reduction takes place in the condensed salt mixture between sodium and titanium subchlorides. Final reduction is a heterogeneous reaction between two separate phases, the a phase which consisted of sodium dissolved in sodium chloride and the ß phase titanium subchlorides dissolved in sodium chloride. The mechanism of the heterogeneous reaction between these phases is electrochemical in nature. The model proposed is a galvanic reaction at the interfacial region.

Jan 1, 1960

By D. H. Baker

THIS REPORT presents the technique and equipment used in determining the hardness of titanium sponge. Detailed descriptions are given of the methods used in preparing test samples for chemical analysis and hardness testing, the method of melting and surfacing test ingots, and the technique of reading Brinell-hardness impressions. The arc-melting furnace described, for which engineering drawings are included, will produce from 70 to 90 double-melted buttons each 8 hours of operation. Experimental data are also presented depicting the effect on hardness of the methods of surfacing specimens, temperature of test specimens, and the effect of time at test load. These data show that surfacing of the specimen involves no critical machining operations but that the test surface must be paralleled by a relatively flat surface for contact with the anvil of the Brinell tester. The heating of a specimen to 150° C. during surfacing does not materially affect the results if the ingot is cooled to room temperature before the hardness impressions are made. The optimum time at load appears to be approximately 30 seconds, but load times of as much as 1/ ½ minutes will not cause major errors.

Jan 1, 1959

By Charles G. Patmon

This paper describing the methods of dredging and treatment of gold-bearing gravels at the Lancha Plana Gold Dredging Co.'s dredge is one of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The dredge is located near the Mokelumne River, 12 miles west of San Adreas, Calif.; it is accessible by an improved dirt road from Jackson, which is about 20 miles distant.

Jan 1, 1932

By C. Özgen Karacan

Longwall mining is an underground mining method during which a mechanical shearer progressively mines a large block of coal, called a panel, in an extensive area. During this operation the roof of the coal seam is supported only temporarily with hydraulic supports that protect the workers and the equipment on the coal face. As the coal is extracted, the supports automatically advance and the roof strata cave behind the supports. Caving results in fracturing and relaxation of the overlying strata, which is called "gob." Due its highly fractured nature, gob contains many flow paths for gas migration. Thus, if the overlying strata contain gassy sandstones or sandstone channels, gas shales or thinner coal seams which are not suitable for mining, then the mining-induced changes can cause unexpected or uncontrolled gas migration into the underground workplace. Vertical gob gas ventholes (GGV) are drilled into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important, first to understand the properties of the gas reservoir created by mining disturbances and, second, to optimize the well parameters and placement accordingly. In this paper, the production rate-pressure behaviors of six GGVs drilled over three adjacent panels were analyzed by using conventional multi-rate drawdown analysis techniques. The analyses were performed for infinite acting and pseudo-steady state flow models, which may be applicable during panel mining (DM) and after mining (AM) production periods of GGVs. These phases were analyzed separately since the reservoir properties, due to dynamic subsidence, boundary conditions and gas capacity of the gob reservoir may change between these two stages. The results suggest that conventional well test analysis techniques can be applicable to highly complex gob reservoirs and GGVs to determine parameters such as skin, permeability, radius of investigation, flow efficiency and damage ratio. The insights obtained from well test analyses can be used for a better understanding of the gob and for designing more effective gob gas venthole systems.

Jan 1, 2009

By Daryl R. Tweeton

The Bureau of Mines compared the effects of surface-active chemicals with those of pure water on core-drilling rock and quartz and on fracturing quartz. The objectives were to determine if these chemicals assist drilling and fracturing rock and if zeta potential control was worth pursuing as an aid to full-scale drilling. All tests were performed in the laboratory. No significant increases in drilling rates were observed for 1 to 10,000 ppm Al (as AlC13) in flushing water when drilling microcline or serpentine, nor for 1 to 10,000 ppm Mg (as MgC12) when drilling microcline or marble. Concentrations near those giving a zero zeta potential were used with microcline and marble. A 50-pct rate increase was observed for drilling quartz in 0.7 ppm oleylammonium acetate, which gave a zero zeta potential. No other concentrations were used. No effect on the tensile strength of quartz thread in 0.05 ppm Al (as AlC13), which gave a zero zeta potential, was observed. Heptanol, reported to give a zero zeta potential on quartz, did not reduce the bending strength of small quartz bars below that in water. These generally negative findings raise doubt about the usefulness of zeta potential control in full-scale drilling. The results, combined with previous studies, suggest that controlling physical properties of drilling fluids, such as viscosity, is more useful than altering chemical properties.

Jan 1, 1976

By W. W. Agey

This report summarizes results of bench-scale metallurgical studies by the Federal Bureau of Mines on three composite samples representative of the low-grade manganese ores purchased by the General Services Administration (GSA) and stockpiled at Deming, N. Mex., and Wenden, Ariz. Bench-scale flotation tests at the Salt Lake City Metallurgy Research Center showed that all three composites could be beneficiated by flotation to recover 88 to 90 percent of the manganese in concentrates that assayed from 38.5 to 39.0 percent Mn, 10 to 12 percent insoluble, 5 percent CaO, 3 to 5 percent Fe, and 1.3 to 1.7 percent combined Pb plus Zn plus Cu, Sintering studies indicated that specification-grade material could be made from these concentrates by sintering above 1,000° C, and adding either sodium or calcium chloride to the charge to insure removal of enough lead and zinc to meet the specifications.

Jan 1, 1962

By Robert W. Thomas

This paper describing the mining practices at the Ray mines at Ray, Arizona, is one of a series being prepared by the Bureau of Mines on mining practices, method and costs in the various mining districts of the United States. At the present time (1929) all mineral Production of the Ray district comes from the Ray Mines of the Nevada Consolidated Copper Co. The ore body is being worked from two shafts, designated as No. 1 and No. 2. An undercut block-caving method of mining is used, variations of which are employed to fit different conditions. The present method has been developed by making improvements as experience was gained or when conditions changed. Refinements in practice are continually being made. The Ray mine was the first in the Southwest to use a caving system of mining on a large scale.

Jan 1, 1929

By Van H. Manning

The term war minerals has been applied t.o those ores and minerals that were largely imported. before the war. Among the mon important of these are manganese, essential for making high-grade steel for munitions and industrial use; graphite, for u,.akin1 crucibles; tin, for plating utAmsils and for bearing-met.al; mereury, used as fulminate t.o explode shells; pot.uh, for making fertilizer and explosives; tungsten and molybdenum, for high-speed t.ool steel; antimony, for hardening bul!et lead; chromite, for tool steel, for tan- , ning leather, and as a refractory lining in furnaces; magnesite, for :refract:A>ry linings; mica, as insulating material; platinum, for the manufacture of sulphuric acid and for electrical apparatus. When the United States entered the war it was clear that every ship would be needed and that the number available for importing minerals would be small. Hence a quick and thorough survey of domestic resources was necessary. . Throughout the war the scope and volume of the war-minerals work increased until it covered practically every mineral that was known t.o be or was liable to be in short supply.

Jan 1, 1919

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By Eric Cather

A mineral investigation of prospects in the Sawtooth Mountains B Wilderness Study Area (WSA) by the U. S. Bureau of Mines in 1983 revealed none had mineral production, resources, or development potential. The area is underlain by tonalite and smaller amounts of schist, One developed prospect and one prospect pit are in the WSA. They are in schist similar to host rock which has yielded gold in nearby mining districts, Sand and gravel deposits in the WSA are large but too far from markets to be considered resources. No energy (oil, gas, coal, or geothemal) resources were identified in the USA.

Jan 1, 1984

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964

By Charles L. Harness, A. T. Coons

Sodium carbonate, Na2CO3, more commonly known as soda ash, is the most important of the alkalies. Sulfuric acid is the only heavy chemical, Soda ash enters the market either as the natural product or as a manufactured derivative of common salt. Notwithstanding their common occurrence in closed basins of the Western States, natural sodas are produced at present by only four firms, all in the same California area, and satisfy only 4 percent of domestic demand for soda ash; soda ash made from salt supplies 96 percent of the requirements. The impossibility in wartime of routing all westbound American shipping through the Panama Cami.l has curtailed Pacific Coast receipts of soda ash and-increased the importance of local resources of natural carbonates. One of the most promising of ·these is the recently discovered trona (sodium sesquicarbonate)· deposit 2o·mnes· west of Green River, Wyo. Reserves are likely to run into hundreds ·of million·s of tons, and the deposit probably could be worked by the room-and~pillar· system of mining, like common salt or coal. • • Raw materials ·ne·cessary for manufacturing synthetic soda ash occur closely associated in m·afiy parts· bf the United 8tates. Almost unlimited resources of salt in brines and in rock-salt depbsits are located near limestone quarries in many areas. The· limesto'ne furnishes the carbon dioxide for the manufacture of soda ash arid the lime f o'r the recovery of ammonia. used in one step of the process. Expansion of the industry to meet wartime needs depends chiefly on availability of trained labor, materials, and equipment necessary for the erection of additional units.

Jun 1, 1942

By A. L. Engel

In recent investigations of chloride Volatilization of gold at the Reno Station, it was found that the addition of small amounts of copper and NaCl to the charge brought about improved volatilization of the gold. The investigations described in this report were concerned with the recovery, in an aqueous medium, of fumes from chloride volatilization of gold. It was attempted to discover a suitable aqueous medium that would permit absorption, solution, or precipitation of all the volatilized gold immediately upon contact with the medium. A simple laboratory apparatus was employed to produce fumes by volatilization. To this furnace was attached an absorption train consisting of a series of chambers containing the aqueous medium, through which the fumes were drawn by suction. A satisfactory synthetic ore that contained metallic, gold in a quartz-matrix was made and utilized, enough. gold being present in a' small amount of material to permit an accurate, metallurgical balance of the volatized values' to be obtained in all the experiments.

Jan 1, 1949

By K. K. Kershner

Sulfide ore concentrates containing cobalt, nickel, copper, lead, and iron were salt roasted and leached on a laboratory scale. More than 95 percent of the cobalt, nickel, and copper was recovered. Heating patterns for salt roasting different concentrates were established. More cobalt, nickel, and copper were recovered from a bulk concentrate composed of a mixture of copper concentrate and iron concentrate. This mixture corresponded roughly with the mixture of these materials in stockpiles in southeastern Missouri. A temperature range of 375° to 400° C. was best for salt roasting. Metal chlorides were leached at a pH of 1 from chloridized charges of concentrates, Although the amounts of cobalt, nickel, and copper extracted were high, the amount of iron dissolved simultaneously interfered with subsequent separation and recovery of these metals. The amount of dissolved iron was reduced substantially by steam treating chloridized charges of bulk concentrate at 300° C. In this way, the ratios of cobalt, nickel, and copper to iron in leach liquors permitted satisfactory separation and recovery of these metals. INTRODUCTION The Federal Bureau of Mines is experimenting with chloridizing reactions.4 5 6 7/ Salt roasting of sulfide ores and concentrates, or their calcines, to form metal chlorides has certain advantages. Chlorides of

Jan 1, 1961

Between 1985-1986, the Bureau of Mines reviewed the mining history and minerals information for areas in and near the San Isabel National Forest to appraise the mineral resources present and determine the types of deposits, and their location in the Forest, that could be mined economically if sufficient demand and metal prices existed. The two major metallic deposit-types that are of national mineral resource significance within the Forest are stockwork- molybdenum (with tungsten and tin) and carbonate-replacement zinc-lead-silver deposits. Historically, small gold placers, gold-quartz veins, silver-quartz veins, skarn iron and copper deposits, volcanogenic copper-zinc-precious metal deposits, and base- and precious-metal veins have been mined. Barite, carbonate rocks, gypsum, other non-metallic deposits, and pegmatites, have also been mined. Sand and gravel, present in large volumes, occurs along and has been mined outside the Forest along the upper Arkansas River valley. Turquoise and gemstones are present in small amounts and are of interest to collectors and jewelers. Geologically, sediment-hosted uranium and copper are present in small occurrences but no resources have been identified. Geothermal resources are related to the Rio Grande rift which parallels the central part of the Forest. Four hot spring areas are present - two of these are within the Forest. Because of the low power requirements of the region, and the presence of other generating facilities, these geothermal resources have had only limited local use. Evaluation of mine models that may be found in the region show that base-metal deposits require a high precious-metal component to be economic. Although molybdenum can be produced at economically competitive prices, there is little demand for the product. Capital costs to start new molybdenum mines would be very high and it is not likely that new mines will be put into production in the near future.

Jan 1, 1989

By M. Clair Smith

This report is one of a series describing exploration, development, mining methods, and costs at United States open-pit mines; the Bureau of Mines prepares and publishes them in cooperation with the mining companies. Their purpose is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods and practices at various United States mines. The exploration, development, equipment, and mining of a large, oxidized-copper ore deposit by open-pit methods, the leaching of the ore with sulfuric acid solution, and the recovery of the copper as cement copper are described herein.

Jan 1, 1958

By F. D. Everett

The Burgin shaft of Bear Creek Mining Co. near Eureka, Utah, was sunk during 1956 and 1957 as part of an exploratory program, searching for lead, zinc, copper, silver, and gold ore bodies hidden from the surface by several hundred feet of volcanic rocks. This paper describes the sinking methods and operating practices of Centennial Development Co., contracting firm for Bear Creek Mining Co., in sinking a 3-compartment vertical shaft 1,100 feet. The operation featured the Cryderman positive-action, clam-type shaft mucker. The shaft was completed in 142 days by a shaft crew of 10 men and a top force of 10 men, including supervision.

Jan 1, 1959

By James Westfield

A brief résumé follows of some of the most recent activities of the Division of Coal-Mine Inspection that have had a favorable effect. on health, safety, and injuries at coal mines: 1. There were approximately 8,510 active coal mines in the United States during 1955. In all, 82,389 regular Federal inspections of coal mines have been made since Public Law 49 became effective in May 1941; 9,823 of these inspections were made during 1955. 2. The Bureau of Mines introduced the revised Coal-Mine Accident-Prevention Course for Supervisors in the coal-mining industry on March 1, 1948. Since that date, 19,455 supervisors and those aspiring to official positions have completed such training conducted by personnel of the Division of Coal-Mine Inspection.

Jan 1, 1956