Search Documents

By A. B. Hooker, L. C. IlsLey

"Field inspections and data relative to the use of rubber-sheathed trailing cables in mines show that much cable is ruined or its probable life shortened by being overheated in service.The length of cable required to make connection from a source of supply to a machine at the face workings may be 100 to 500 feet. As a rule, the cable is carried on a reel and unreeled as required; and thus in most cases soma of the cable is not removed from the reel. The overheating generally occurs in that part of the cable which is left on the reel.Factors that determine the heating of trailing cables are:1. The size of the conductors in the cable.2. The maximum energy to be supplied through the cable, based upon the horsepower of the motor and the degree to which the motor is loaded.3. The voltage of the supply and the variation of the voltage at the receiving end.4. The time length of current flow and whether continuous or intermittent.5. The kind of current (direct or alternating).6. The amount of ca· le left or the reel.7. The type of cable used.8. The kind of reel used.In connecti0n with an investigation of the general performance of rubber-sheathed trailing callas, the Bureau of Mines has made a limited study of some of these factors, including the following points:"

Jul 1, 1931

By F. J. Perzak

The Bureau of Mines conducted a study to develop a standard fire test for 5-gal containers used for storing combustible fluids in underground coal mines. A standard test method was developed which evaluates the performance of the container in a 4-min tray fire. Bureau investigators used the standard test method to evaluate several types of closed 5-gal plastic and metal cans in outdoor tests. Each can tested contained 1 gal of nonfire-resistant (NFR) hydraulic oil. A container failed the test if it lost its contents in any of seven trials. Contents spilled either as a result of thermal rupture or melting. Fewer than 10 pct of the metal containers failed this criterion, but all the plastic containers failed. The metal container failures were usual-ly due to tipping over during pressure relief, which spilled the NFR oil. Replacing the NFR oil in the container with kerosene resulted in failure of more than 30 pct of the metal containers. The standard tests and preliminary tests showed that plastic containers are not equivalent to metal containers in their ability to contain combustibles such as lubricants and greases in a fire. For solvents and lubricants more volatile than NFR hydraulic oil, approved metal safety containers are recommended.

Jan 1, 1985

By W. R. K. Wu

This Bureau of Mines report presents a statistical study of the repeat abilities of coal-plasticity parameters obtained in the tests with the Gieseler plastometer and the Audibert-Arnu and Hoffmann dilatometers. Repeatability is expressed in terms of one or two standard deviations for the differences between duplicates. The statistical method employed here is summarized. Results are tabulated for the temperature and nontemperature parameters of the three tests.

Jan 1, 1970

By H. F. MILLE, Charles A. Kumke

This paper describes mining operations at the Iron King mine of the Shattuck -Denn Mining Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices and methods in various mining districts of the United States . The mine and surface plant of the Iron King mine are situated in secs . 15 and 21 , T. 13 N. , R. 1 E. , about 20 miles by State highway 69 east by southeast from the city of Prescott and 1 mile southwest of the mining town of Humboldt on the Prescott -Mayer branch of the Atchison , Topeka & Santa Fe Railroad (fig . 1 ) . A l-mile truck haul brings the mill concentrates (lead and zinc ) to bins on a siding of this line at Humboldt ; the silver -gold bullion is handled separately . Some of the oldest residents in the vicinity of Prescott claim that the original location for the Iron King mine was made in 1880. The earliest recorded production was in 1906-1907 . During the first World War the mine produced fluxing ore for the Humboldt smelter . In 1936 the property was purchased under tax sale , and a mill (140-ton capacity ) was erected in 1938. The capacity of this mill was increased to 225 tons the following year , and a cyanide plant was added in 1940 to treat mill tailings . In 1942 the Shattuck -Denn Mining Corp. purchased the property . A new working shaft was sunk , mine development was speeded , and mill capacity was again increased . The predominating locally formation of this district is a pre -Cambrian schist known as Yavapai schist . The Iron King deposit , which carries gold, silver , lead , zinc , and copper , occurs as a series of lenses in a sheared zone of the pre -Cambrian schist . Down to the 600 -foot level the ore was mined and drawn by the shrinkage method . The cut -and -fill method was adopted for the lower levels . Waste rock for stope fill was provided by block-caving an area on the 600 level . Main haulage drifts were driven in the firm footwall , and crosscuts were driven across the mineralized zone at 100 -foot intervals . Grab samples taken from each car of every working place and channel samples cut every 5 feet in development work are considered sufficient for estimating ore reserves .

Jan 1, 1950

By J. D. Sargent

Selenium might be described as a paradoxical element, being either a metal or a nonmetal, a conductor or nonconductor, amorphous or crystalline, colorant or decolorant, and a hydrogenator or dehydrogenator. Selenium was discovered in 1817 by the Swedish chemist, Berzelius, while studying flue dust from the lead chambers of the sulfuric acid works at Gripsholm, Sweden, The ordinary stable form of selenium is a crystalline, grayish solid with semi-metallic luster. It melts at 217° C., boils at 684.8° C., and has a density of 4.79.

Jan 1, 1955

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994

By J. R. Thoenen

This circular is the second of a series presenting methods employed in solving the technical problems encountered in the production of sand and gravel. The first paper3 discussed the methods use in prospecting and exploration. This one teals with the problems involved in bringing a raw prospect to the production stage and considers the various methods of development and the Factors affecting that development. Later publications are planned to present and discuss methods of recovery and treatment. The recovery of sand and ravel from natural deposits and their preparation for market involve a progressive sequence of operating steps or processes. Each step or process presents its own peculiar problems which require different angles of mental approach, methods, and tools, but all are more or less dependent on the step or process which precedes or follows.

Jan 1, 1933

The method of using large-diameter augers to recover coal was introduced to the mining industry about the end of World War II, and production of bituminous coal with augers has increased steadily to an estimated 7 million tons, or approximately 1.4 percent of the total mined in 1956. Although auger mining has proved to be a reliable and economical method of mining coal, a number of unfortunate fatal accidents have been experienced; consequently the need for these recommended safety standards is indicated for this comparatively new method of coal mining. As mining methods and equipment change from time to time and new hazards are introduced, these standards will be revised; therefore, questions or suggestions from the coal-mining industry will be welcomed and carefully considered.

Jan 1, 1958

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By K. K. Kelley

Sodium-aluminum and potassium-aluminum silicates are among the more important rock-forming minerals of the earth's crust. They also appear as constituents of some metallurgical slags and of some refractory materials. Consequently, knowledge of their thermodynamic properties is interesting and valuable from several viewpoints. This paper reports experimental determinations of the low-temperature heat capacities and entropies at 298.16° K. of albite, jadeite, and nephelite it the sodium-aluminum silicate series and of adularia, ferriferous orthoclase, leucite and kaliophilite in the potassium-aluminum silicate series. Also high-temperature heat-content and entropy increments about 298.16° K. are reported for albite, jadeite, nephelite, and carnegieite in the sodium-aluminum silicate series. Except for a few high-temperature heat-content values for albite, all these data are available for the first time.

Jan 1, 1953

By Terry J. Close

Between 1986 and 1989, at the request of the U. S. Bureau of Land Management, personnel from the U. S. Bureau of Mines Western Field Operations Center studied the highly-mineralized, 25,335-acre, Crack Canyon Wilderness Study Area (UT-060-028A), to evaluate its identified mineral resources. The 16-mi-long, 2-mi to 4-mi-wide stud/ area is on the southeast side of the San Rafael Swell, about 40 mi southwest of Green River, Emery County, southeast-central Utah. The study area is underlain by Mesozoic sedimentary beds. Uranium, the principle mineral resource, occurs in two formations. The principle uranium deposits are in mudstone, sandstone, and conglomerate lenses in the 22-mi-long outcrop of the Triassic Chinle Formation which parallels and straddles the northwest boundary of the study area, Some small low-grade uranium occurrences and an extensive gypsum deposit are hosted by the Jurassic-age rocks that underlie the southeast part of the study area.

Jan 1, 1989

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the tenth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Knott County, Ky., which comprises parts of the Salyersville, Prestonsburg, Troublesome, Hindman, Pikeville, Cornettsville, and Whitesburg quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By N. S. Petersen

As part of the Demand Evaluation Program of the Bureau of Mines to determine future needs for minerals, a study was instituted to develop and describe a methodology for approaching the problem of substitution between mineral commodities and between mineral commodities and other materials. The report comprises three sections: A review of general factors relative to substitution, a case study of the effect of substitution on zinc die-casting markets in recent years, and a general methodology for reviewing materials substitution with specific emphasis derived from reviewing substitution in the domestic zinc die-casting markets.

Jan 1, 1971

By E. J. Ostrowski, P. L. Woolf, J. P. Morris, Norwood B. Melcher

By injecting natural gas through auxiliary tuyeres into the smelting zone of the Bureau of Mines ' experimental blast furnace in January 1959 , the investigators succeeded in reducing the coke consumption by approximately one - third that of the base period . This caused a 30 - percent increase in pig iron production with no increase in wind rate . The maximum gas addition in these experiments was 4,665 cubic feet per ton of metal produced . Sharp reduction in gas consumption occurred when high hot blast and high wind rates were used , although the gas injection rate in percent of air blown remained constant . As the heat energy produced by burning natural gas to carbon monoxide and hydrogen is much less than burning coke to carbon monoxide , greater blast temperatures were required during the test runs . The gases produced from the methane were , however , more effective reductants ; so it was possible to increase the production rate while reducing the total heat requirements per ton of metal produced . During a base period with an all - sinter burden , before introduction of natural gas , a coke rate of 1,484 pounds per net ton of pig iron was attained , using an average blast temperature of 1,518 ° F. Gas was introduced gradually over a two -week period until an average 7 percent of the air blown was reached . During this period , the wind rate was adjusted downward to maintain a constant flow of gas in the bosh . The production rate of the furnace remained relatively constant . The quality of pig iron, however , improved as the sulfur load on the furnace was reduced as a result of the substitution of gas for coke . Blast temperatures were increased during this period from 1,518 ° F. to 1,939 ° F. , when the maximum gas addition was reached .

Jul 1, 1960

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing gypsum mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation so that there may be no misunderstanding of the scope of the cost tabulation. This paper deals specifically with the mining and crushing methods employed by Victor Plaster, Inc., Victor, Ontario County, N. Y. The maximum annual production capacity of this company is 150,000 tons of crushed gypsum. The methods and practices employed arc typical of those followed in the gypsum mines in western New York State. The shaft is, perhaps, the deepest and the thickness of the gypsum mined is above the average for the section.

Jan 1, 1937

By W. R. K. Wu

Results of linear correlations of two to four variables by the least-squares method are presented. The variables include 63 parameters representing coal composition, coal plasticity, and coke strength. The composition parameters are on chemical analyses; the plasticity parameters, on three plastometer and dilatometer tests and four miscellaneous tests; and the coke-strength parameters, on three ASTM indices. Seventy-two to eighty-four plastic coals were used in the plasticity and carbonization tests, which together form the basis of this report; 43 nonplastic or weakly plastic coals were used in the coal-band studies. Plots of relations between volatile matter, carbon, and oxygen contents of 1,860 U.S. coals and the 84 coals used are shown. Similar plots between volatile matter and hydrogen or atomic H/C of the 84 coals are also included. Significances of regression coefficient signs for coal composition parameters in the significant correlations found are discussed. Based on these significances, the following relations are shown: (a) coke strength versus average aromaticity, or mineral matter content, of the parent coal; (b) characteristic temperatures of the plastometer and dilatometers, the free-swelling index, or the Gray-King type versus average hydroaromaticity of the coal; and (c) nontemperature parameters of the plastometer and dilatometers versus the physical properties of a certain group of compounds from thermal decomposition of coal. Similarly, significances between the positions of coals in the coal band and the aforementioned relations are also discussed. A structural theory of coal plasticity is proposed. Applications of the correlation results are discussed. Composition parameters, such as carbon, atomic H/C, and calorific value may be used as a basis for selecting coking coals for stronger coke. Plasticity parameters, such as the end temperatures of the plastometer and dilatometers and the free-swelling index, may be used for the same purpose. Based on the best correlations found, coke-strength indices may be estimated to within 4 to 8 units of the observed values; the end temperatures of the plastometer and dilatometer tests, 5° to 10° C.; and the free-swelling index, within 1 unit. Accuracies of all these estimated values are examined, based on the experimental errors of the data involved. Finally, estimations of plasticity parameters from one test with those from others are shown.

Jan 1, 1971

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H2O) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium, chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained, but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process. In all of the processes suggested for the recovery-of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation.

Jan 1, 1934

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991

To expediate the transfer of technology from Bureau laboratories into new products and processes that enhance the economic competitiveness of the U.S. mining and minerals industry in world markets. Background The U.S. Bureau of Mines and various members of the industry are concerned about the current technology challenge to the minerals industry in the United States. They arc working together to delineate ways of enhancing the mineral industry's technology base. More emphasis is being placed on collaboration between the government, academia, and industry to formulate the innovative revolutions needed to maintain our technology edge. Through these partnerships, real issues and problems can be identified, the industry's needs as customers can be defined, and research and development activities can be tailored to meet these needs. Now is an especially exciting time in research because some special opportunities exist to encourage private industry to capitalize on Federal laboratory research and development. These opportunities arc called CRADA's. What Is A CRADA? The Congress recently enacted a mechanism that enhances collaboration between industry and government through the Technology Transfer Act of 1986. A key lea lure of this Act is a provision through which Cooperative Research and Development Agreements or CRADA's can be developed to encourage industry and government to work together and stretch their research budgets. By entering into a CRADA, a private, non-Federal company can cost-effectively perform research by sharing the costs of this research with the Federal Government. The agree¬ment involves no transfer of funds from the Government. The Government agrees to provide personnel, services, facilities, equipment or other resources (but nut funds) and the non-Federal party agrees to provide funds, personnel, services, facilities, equipment, or other resources needed to conduct a specific research or development effort.

Jan 1, 1992

By B. W. Naugle

A small-scale laboratory coke oven similar to those described by Swiniarski, Cryan, and Altieri and Fuchs, Sandhoff, Taylor, and Gauger was built by the Bureau of Mines in 1943. Tests made since that time have indicated that such a small oven is of questionable value in predicting the coking pressures to be expected in commercial coke ovens. This summary of the work done has been prepared at the suggestion of the Advisory Committee to the Bureau of Mines-American Gas Association Survey of Carbonizing Prop¬erties of American Coals.

Jan 1, 1948