Search Documents

By G. G. Campbell

Bureau of Mines research to develop an in situ retorting recovery method for oil shale has involved field testing of fracturing techniques for creating fluid-flow paths in impermeable oil shale. Electrolinking, hydraulic fracturing without and with sand propping, and explosive fracturing with a liquid explosive were tested in a 25-ft-square, five-spot pattern. These wells were drilled into oil shale at 50-to 88-ft depths near Rock Springs, Wyo. Results of the fracturing tests were evaluated by injecting air into a test well and measuring flow rates and flow profiles in adjacent test wells before and after each test. To identify points of air entry (location of fractures) in wells, flow profiles were determined by use of inflatable packers and by continuous logging with an airflow probe developed during the fracturing program. Electrolinking and hydraulic fracturing without sand propping were relatively ineffective; hydraulic fracturing with sand propping created horizontal fractures with desirable flow capacity; and fracture flow capacity was significantly increased by detonation of nitro-glycerin displaced in the natural and hydraulically induced fracture systems.

Jan 1, 1970

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By Charles Will Wright

This paper will be of interest to those who are actually developing a mineral prospect or planning to do so, as well as to investors who are considering the problem of financing the development of the prospect, so that they may know what the risks are and what capital expenditures are necessary before a prospect may become a mine. The term "prospect" used broadly, as it is in this paper, is defined as any property that has a mineral showing of sufficient interest to warrant development, irrespective of prior work, Such previous exploration, however, may be extensive and consist of several tunnels or adits connected by raises, or of shafts with several levels. There may also be a small mining and milling plant on the prospect which, because of the lack of capital for development or the lack of markets for the products, is now idle. Such prospects may warrant further capital investment for development work or for a mine plant to raise to the stage of profitable production.

Jan 1, 1935

By W. S. Landers

This report presents a study by the Federal Bureau of Mines of technical factors related to the production of special carbon and tar from selected Wyoming coals. Certain Wyoming high-volatile bituminous and subbituminous coals were processed in bench-scale apparatus to determine potential carbonization yields and in pilot plant retorts to produce sufficient char and tar for testing. These tests have shown that a critical selection of coal is necessary when the coal is processed for a specialized carbon. Generally high yields of tar are obtained from low-temperature carbonization of Wyoming high-volatile bituminous and subbituminous coals, and the yield of tar usually increases with increase in rank within this range of coals. The production and evaluation of industrial carbons from Wyoming coals by using pilot plant and bench-scale techniques is part of the continuous program of upgrading western coals. It has been found that: 1. Most Wyoming coals are nonagglomerating and may be carbonized in fluidized systems. Chars produced in pilot plant retorts at low temperatures contain about 17 to 23 pct, residual volatile matter and are easily ignited. These chars appear suitable as power plant fuel. The tar-plus-light-oil yields range from 14 to 40 gal./ton of raw coal processed. 2. Wyoming high-volatile coals produce a slightly smaller and somewhat weaker coke than currently mined Western United States high-volatile coals used commercially as blending stock in metallurgical coke production.

Jan 1, 1961

By J. L. Reuss

The Bureau of Mines investigated the technical feasibility of smelting copper concentrates containing chalcocite (Cu2S) and native copper using nonpyritic sulfur-bearing materials to aid matte formation. The procedure consisted of combining various proportions of commercial chalcocite concentrate, smelter slag, fluxes, and matte-forming constituents to produce charges of comparable compositions. The mixtures were charged in fire-clay crucibles and smelted in an induction furnace at 1,300° C. The research proved that either sulfur or gypsum can replace pyrite as a matte-forming material, and that gypsum produces an exceptionally high-grade copper matte. The addition of small quantities of metallic iron to the nonpyritic smelting charge furthers the removal of sulfur, improves the recovery of copper, and makes it possible to utilize gypsum as the exclusive flux and matte-forming ingredient, thereby eliminating the necessity of adding limestone.

Jan 1, 1968

This report is the first in a "final" series of publications on the Juneau Mining District (JMD). This volume summarizes the results of Bureau of Mines (Bureau) investigations in the JMD during the period 1984-1988. Volume 2 consists of a detailed description of Bureau investigations of mineral de-posits, prospects, and occurrences. Volume 3 is a report on industrial minerals within the district. This study has identified and examined more than 300 mines, prospects, and occurrences containing gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and PGM. More than 20 of these were discovered during this study. An additional 20 prospects not mentioned in the literature were rediscovered during the JMD study.

Jan 1, 2012

By R. Hogg

"The problems of sampling particulate materials, and of characterizing the distributions of particle size and composition are reviewed. Requirements for sampling from comminution systems are discussed and a simple formula is presented for estimating the minimum sample size needed. The limitations and errors associated with the techniques available for particle size analysis are evaluated and guidelines are suggested for the selection of appropriate methods. The use of microscopic and macroscopic approaches to the characterization of particle composition are discussed.INTRODUCTIONComminution is a process of particle size reduction in which the goal is to produce a material with a specified particle size distribution from a coarser feed. In mineral processing applications, the product size distribution is often qf secondary importance to the extent to which individual mineral grams can be liberated from one another. However, due to poor understanding of the nature of the liberation process and the lack of reliable procedures for characterizing it, the actual specification is normally in terms of particle size.Particle size distribution can be regarded as the fundamental characteristic of a particulate system. The distributions of particle shape and composition among the various particle sizes present are often sufficient to define the bulk properties and behavior of the system. Description of the distributions of size; shape and composition of the different phases which may exist within individual particles is necessary to complete the picture and is especially important for predicting liberation etc., in comminution processes. It is quite obvious that · the complete characterization of real particulate systems is a formidable, if not .impossible task. Practical characterization procedures should involve ·evaluation of those characteristics which are deemed to be important and which can be measured. In comminution systems, this should ideally include the particle size distribution, the size-by-size distributions of particle composition, and as much information as can be acquired on the internal composition and structure of individual particles. In most cases, of course, we fall far short of even this rather limited goal."

Jan 1, 1988

By G. W. Reimers

Metastable pyrophoric wüstite (FexO, with x between 0.89 and 0.95) was found to be much easier to grind to colloidal state than were its stable disproportion products magnetite or iron. The grinding of polycrystalline magnetite appears to be complicated by the magnetic flocculation arising from interparticle attraction. This is superimposed on the attraction of a fluctuating electric dipole for a neighboring induced dipole. More than 85 pct of the tumbling time was saved by grinding antiferromagnetic wüstite instead of the ferrimagnetic oxide of iron (Fe304). Disproportionation of colloidal wüstite to the stable ferromagnetic and ferrimagnetic colloidal particles of alpha-iron and magnetite, respectively, was accomplished rapidly at temperatures above 250° C but below 570° C, the eutectoidal stability point of the wüstite phase.

Jan 1, 1972

By Mackenzie Burnett

Quick-Fix Blowout Stoppings were evaluated in several underground mines as an alternative to conventional ventilation control bulkheads. Blowout stoppings offer considerable savings in bulkhead construction and repair costs if the 0.1 inch H20 of differential pressure required to inflate them is available. The Quick-Fix Blowout Stoppings were utilized successfully in uranium mines in the Southwestern United States where savings in bulkhead construction and repairs to blast damaged bulkheads are estimated to equal $9,500 over the projected 2 year average life of a blowout stopping. Two types of material were evaluated. Five methods of anchoring the stoppings to drift walls were evaluated. Three methods of anchor attachment to the stopping material were evaluated. Blast pressure measurements were made in conjunction with the evaluation of the blowout stoppings.

Jan 1, 1978

By K. O. Bennington

The thermodynamic properties of hedenbergite, of composition [(Ca0,9516) (Mg0,0583Fe2+0.7134 Fe3+0.0934 Mn0,1366) (Si206)], were experimentally determined at the Bureau of Mines. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -680.96±0.855 kcal/mol. The standard enthalpy of formation from the oxides is AR-96 = -24.55±0.485 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 12.3 to 300.1 K. The derived standard entropy is S-98 - 41.218±0.148 cal/mol-K. High-temperature heat capacities were measured with a differential scanning calorim¬eter from 397 to 1,147 K. These experimentally determined data were combined with data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation are given as a function of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -641.90±0.86 kcal/mol.

Jan 1, 1984

By J. P. Hansen

Reducibility tests were run by the Bureau of Mines on an open hearth lump ore and four groups of pellets whose smelting characteristics had been deter-mined previously in the Bureau's experimental blast furnace. When reduction data from various tests were plotted on specially prepared paper l-(l-percent reduction/100)1/3 against time, the plots were linear. The iron-wustite inter-face therefore advances at a constant rate. The rate of the interface advance in mm/min was used as a reducibility index. The reducibility index measured at 900° C, using 0.45 cu ft hydrogen per minute varied inversely with the surface area of the sample. Even with carefully controlled surface areas, how-ever, duplicate reducibility indices varied considerably. When enough tests were run to give a stable mean, the mean reducibility index did correlate with blast furnace production for the four pellet groups. Results indicated that if the interface speed itself were to be used for correlation with blast furnace production, a sample size of about 180 grams of minus 0.742-plus 0.525-inch particles should be used with a test temperature of 900° C and a flow of 0.45 cu ft hydrogen per minute.

Jan 1, 1966

By D. E. Redmon

Linear programing provides a mathematical technique by which activities can be planned in such a way that an optimal result is obtained. Routine applications of linear programing require only a knowledge of algebra. However, a complete understanding of the fundamentals of linear programing requires a knowledge of advanced mathematics. The purpose of this publication is clarification of terminology and illustration of applications in comparatively simple mining problems. Two mining situations are considered: Mine stopes from which ore is to be produced at a minimum production cost; also, uranium mines from which ore is transported to one mill, a maximum monetary value is desired. The details of data arrangement for solution by linear programing are described and the solutions are presented. Results of these solutions indicate successful applications of linear programing to mine production scheduling.

Jan 1, 1964

By E. C. Lane

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of samples of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 3162/4 is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of sample of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 31624/ is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By S. M. Runke

The purpose of the work described in this publication was to determine, on a pilot-plant scale, the practicability of concentrating low-grade bauxite deposits to render them suitable for the extraction of alumina. In 1941, when it became apparent that the United States might soon be drawn into war, the government, through its various agencies and bureaus, began to stimulate and increase production from domestic reserves of bauxite, which is the principal raw material for the production of aluminum. This activity, which was centered in Arkansas, where 95 percent of the domestic reserve is situated, reached peak production when enemy submarine warfare greatly hindered imports from foreign sources. During this period the average domestic production in Arkansas rose from approximately 300,000 long wet tons to something over 6,000,000 tons in 1943.

Jan 1, 1949

By Kenneth L. Rubow, Virgil A. Marple, Zhigun Zhang

"A theoretical technique has been developed and verified experimentally for determining the aerodynamic diameter of irregular shaped particles. The aerodynamic diameter of a particle is a very important parameter for determining where that particle deposits in the respiratory tract. Many instruments, such as impactors and cyclones, will determine the aerodynamic size distributions of aerosol particles but few analyze the particles individually. The theoretical approach of our technique is to solve, by use of high speed computers, the three-dimensional Navier-Stokes equations to obtain the flow field around an irregular shaped particle of any contour. The computer program will then determine the drag on the particle, and thus the aerodynamic diameter of the particle can be calculated. The experimental approach has been to pass the particles through a centrifuge and collect the particles upon a collection foil. The position of a particle on the foil is an indication of its aerodynamic diameter. These particles were then shadowed in two orthogonal directions and inspected under an scanning electron microscope (SEM). The top view of the particle in the SEM plus the views of the two orthogonal shadows allows one to determine the three-dimensional shape of the particle. Studies have been performed on silica, coal and talc particles with aerodynamic diameters in the 1 to 4 µm size range. The three-dimensional shape, as is determined from SEM analysis, was used in the theoretical computer program and the results compared. It was found that in most cases the agreement between the experimentally and theoretically determined aerodynamic diameters was within 5%. INTRODCJCTIONThe equivalent aerodynamic diameter (EAD) of a particle, defined as the diameter of a unit density sphere with the same falling speed as the particle in question, is an important size measurement of the particle. This is especially true when attempting to predict where particles may deposit in the respirator tract. Therefore, EAD is an important parameter when considering respiratory diseases caused by particles, such as coal workers pneumoconiosis (CWP).Many instruments will measure the EAD size distribution of the aerosol particles, but few analyze the particles individually. Impactors, cyclones and virtual impactors normally collect particles upon substrates or filters which are · then analyzed gravimetrically to determine the mass concentration of the particles in that size classification. The EAD of particles can be measured on an individual basis with centrifuges, inertial spectrometers and the TSI Aerodynamic Particle Sizer (APS). Centrifuges are most ideally applicable for studying individual particles as the particles are deposited, on long removable foils, at locations dependent upon their EAD."

Jan 1, 1990

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929

By Robert E. Dye

This paper describing the mining methods employed and setting forth prevailing, costs at the property, is one of a series being prepared by the United States Bureau of Mines dealing with properties in various mining districts of the United States and Canada. The Vipond mine is a gold property located at Timmins, Ontario, Canada, and operated by the Vipond Consolidated Mines (Ltd.). For the past fiscal year (ended July 31. 1930) ore was mined and milled at the rate of 310 tons per day, and the value of the bullion produced was $896,397.61.

Jan 1, 1931

By P. D. Lindahl

[A cost/benefit analysis was conducted by comparing the industry cost to protective structures on low-coal face equipment with the benefits paid for injuries/fatalities considered preventable by the use of these structures. Th industry costs were based on estimates by OEM's and rebuild shops for install protective structures on new and rebuilt face equipment. The accident benefit was based on evaluations performed by the USBM Accident Cost Indicator Model. Industry wide population data were developed on low-coal face equipment and injuries/ fatalities preventable with protective structures. The results of the analysis are to be used as a tool by USBM in determining the feasibility of continuing development of cab and canopy technology for low-coal equipment.]

Jan 1, 1983