Search Documents

By Raymond W. Hiteshue, Sam Friedman, Robert Madden

Experiments were made in a semicontinuous unit to provide engineering data for designing experimental continuous systems . These systems would be used to study the hydrogasification of hvab coal and char (from lowtemperature carbonization ) to high - Btu gas . In experiments at 800 ° C and with a coal residence time of several seconds , yields of hydrocarbon gases increased from about 2,000 scf / ton of maf coal at 250 psig to 7,000 scf at 1,000 psig . With 15 minutes residence time , yields increased from 8,000 scf/ton of maf coal at 250 psig to 17,500 cubic feet at 1,000 psig . In all cases , small quantities of heavy oils were produced along with the gaseous hydrocarbons . Production of oils could be minimized with a corresponding increase in gaseous hydrocarbons by increasing the retention time of the volatiles within the hot zone . Yields of gaseous hydrocarbons from char were slightly greater than from coal under similar conditions . Although the hydrogasification reaction is very pressure dependent , substantial quantities of coal (40 to 60 percent ) could be reacted to gaseous hydrocarbons at pressures as low as 50 psig provided reaction temperatures were increased to 1,200 ° C. It was also demonstrated that a hvab coal could be hydrogasified continuously without incurring agglomeration . This was achieved by dispersing coal in a relatively large reactor with concurrent flow of hydrogen . At 1,000 psig and 800 ° C , it was possible to react about 35 percent of the coal and to produce a gas containing up to 52 percent methane .

Jan 1, 1964

By W. M. Traver

As a direct result of the second World War, consumption of nickel in the United States has increased to such an extent that it has been considered timely to investigate undeveloped deposits of the nickel minerals. Funds were made available to the Bureau of lines in 1941 to investigate the extent, occurrence, and quality of nickel ores in the Mirror Harbor area. The Federal Geological Survey mapped' and studied the area during the summer of 1941 and Robert S. Sanford, an engineer of the Bureau of lines, made a preliminary examination in June 1942. A contract for drilling the deposits under the direction of the author was let in July 1942.

Jan 1, 1948

By J. A. Kosek

Work has been carried out under Bureau of Mines Contract HO 395132 to develop improved sensor cells for use in direct-reading detectors and diffusion exposure meters. A pumped CO sensor cell was developed which has a shorter response time, improved temperature cycle characteristics, and improved linearity and stability at high CO concentrations. Diffusion CO sensor cells have shown good response level stability and linearity up to 1000 ppm. In addition, a new sensor cell catalyst has been developed for NO2 sensor cells which has a much shorter response time and improved response stability characteristics.

Jan 1, 1982

By Jeffrey Shawn Peterson

The testing procedures of the u.s. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break-flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2010

By Alla D. Mah

The heats of combustion of three chromium carbides, Cr23C6, Cr7C3, and Cr3C2, were determined by combustion calorimetry. Heats of formation calculated from the results follow: ?Hf°298 (Cr23C6) = -94.7 ± 5.0 kcal/mole, ?Hf°298 (Cr7C3) = -43.3 ± 1.7 kcal/mole, and ?Hf°298 (Cr3C2) = -22.5 ± 0.8 kcal/mole.

Jan 1, 1969

By Frank E. Cash

The iron-ore ranges in the Lake Superior district are the liarquette in Michigan, Menominee and Gogebic in Michigan end Wisconsin, and the Vermilion, Mesabi, and Cuvuna in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years. During the 4-year period 1940 to 1943, inclusive, 323,667,599 long tons of iron ore was shipped from the Lake Superior district.4/ Michigan and Wisconsin shipped 65,386,608 tons, or 20.2 percent of the total, and employed approximately 15,000 men; Minnesota shipped 258,280,991 tons, or 79.8 percent of the total, and employed approximately 10,000 men. The tons produced per man employed is much, greater in Minnesota than in Michigan and Wisconsin owing to the large open-cut production in Minnesota.

Jan 1, 1945

By Radford Schantz

In 1990, the Bureau of Mines (BOM) conducted a mineral investigation of the mines and prospects in the East Mojave National Scenic Area (EMNSA). San Bernardino County. California During field work. BOM identified 701 mines and prospects in EMNSA for which the geology, mineral resources, and mining history were compiled and summarized. Analytical results for 1.188 rock samples collected are tabulated. Total value of identified resources in EMNSA is $5.0 billion. Twenty-four mines and prospects were deemed profitable under current economic conditions. Development could generate considerable economic benefits to San Bernardino County. Potential economic benefits from mining the deposits were evaluated under the following access restrictions for EMNSA: 1) fun access, 2) HR 3460, and 3) S 11/HR 780. Under the full access scenario, cumulative mine revenues are $3.0 billion, cumulative personal earnings at mines and supporting industries are $0.94 billion, and annual jobs at mines and supporting industries are 2,379. Under HR 3460, mine revenues, personal earnings, and annual jobs are $2.9 billion. $0.88 billion, and 2,165, respectively. Under S 11/HR 780, mine revenues, personal earnings, and annual jobs are $1.0 billion, $0.32 billion, and 936, respectively.

Jan 1, 1990

By William G. Pariseau

A small displacement-small strain finite element technique utilizing the constant strain triangle and incremental constitutive equations for elastic-plastic media that are nonhardening and obey a Coulomb yield condition has been applied to the analysis of gravity flow initiation in a V-shaped hopper containing a powder under lunar environmental conditions. Three methods of loading were examined. Of the three, the method of computing the initial state of stress in a filled hopper prior to drawdown by adding material to the hopper layer-by-layer is superior (as expected). Results of the analysis of a typical hopper problem show that the initial state of stress, the elastic moduli, and the strength parameters have an important influence on material response subsequent to the opening of the hopper outlet.

Jan 1, 1971

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961

By Alla D. Mah

Relatively pure aluminum nitride (AIN) recently has been prepared in sufficiently large amounts to permit a variety of experimental studies.4/ Several mechanical and chemical properties have been investigated, which show that this substance has good potentialities as a container for liquid aluminum, gallium, and boric oxide. The present work by the Bureau of Mines was undertaken to obtain thermo-dynamic data pertinent to the calculations regarding thermal stability and reactivity of aluminum nitride. The following measurements were made: (1) determination of the heat of formation from the elements at 298.15° K.; (2) determinations of the heat capacity over the temperature range 51° to 298.15° K. and the evaluation of the entropy at 298.15° K. therefrom; and (3) determinations of the heat content over the temperature range 298.15° to 1,800° K. These data are combined to obtain free energies of formation from the elements between 298.15° and 2,000° K.

Jan 1, 1961

By John W. Moore

The discovery of porphyries in petroleum by Treibs (17-19) is one of the most significant achievements relating to the origin of petroleum. The presence of these remnants of chlorophyll and hematin in petroleum has immediate practical interest in several aspects of the petroleum industry. Because of their interfacial activities and film-forming tendencies, the metal-porphyrin complexes may be expected to affect the wettability of petroleum-reservoir rock surfaces and influence the flow of fluids in these reservoirs. Also, studies of the relationship of trace elements and porphyrins in petroleum may be expected to yield valuable information on source beds and petroleum migration. Finally, the extreme stability of several metal-porphyrin complexes complicates removal of these metals from some petroleum stocks where they exert deleterious effects on processing and utilization. Metal-porphyrin complexes are commonly associated with the asphaltic residues of crude oils in which they occur (8, 9, 15). However, investigations in this and another laboratory (15) show that small amounts of these complexes often remain in partly refined petroleum products, such as thermally cracked distillates and deasphalted stocks.

Jan 1, 1957

By L. A. Neumeier

A refinement of the tungsten-cobalt phase diagram is presented for compositions to 85 at. pct cobalt and for temperatures to the solidus. Preparation of alloys by powder metallurgy methods is described, and the results of studies made by a combination of techniques involving microscopy, X-ray diffraction, thermal analysis, and dilatometry are discussed. The existence of u-W6Co7 is confirmed (rhombohedral D85 structure). The W6Co7 phase forms periectically at 1,685'115° C by reaction of liquid with primary W; the peritectic melt is at 71 at. pct cobalt. The homogeneity range of u-W6Co7 extends to both sides of the ideal stoichiometric ratio, through a compositional range of about 5 at. pct. The compositional limits for u-W6Co7 vary slightly below 1,471°±5° C, the temperature of the eutectic reaction forming u-W6Co7 plus a. The eutectic composition is at 79 at, pct cobalt. The existence of WCo3 is confirmed (hexagonal D019 structure). WCo3 forms peritectoidally at 1,093°±5° C by reaction between a and u-W6Co7 and exists over a narrow homogeneity range of 0.5 to 0.6 at. pct. The solid solubility of cobalt in tungsten is low (maximum 0,9 at, pct cobalt) and results in contraction of the tungsten lattice. Tungsten is extensively soluble in a-Co at higher temperatures; the a-Co lattice is expanded by the presence of tungsten in solid solution. There was no indication of the formation of a o-phase nor of any intermediate phases other than WeCo7 and WCo3. The WeCo7 and WCo3 phases are compared with similar phases in other systems.

Jan 1, 1967

By David D. Walker

The purpose of the investigation was to describe and appraise tungsten deposits in Montana . The work supplements previous investigations made by Pattee ( 10 ) and Walker ( 17 ) in selected areas of the State . Scheelite deposits in tactite are the most numerous and most important economically , having accounted for nearly all of the State's tungsten production . Of the 64 deposits examined during the current study , 50 contained scheelite , 11 hubnerite , 2 wolframite , and 1 ferberite . The State's major tungsten production has been from scheelite deposits in Beaverhead County . The report lists , by counties , the type and grade of each deposit . The more important occurrences are accompanied by geological and assay maps .

Jan 1, 1963

By Gerald A. Muson, Fremont F. Clarke

"INTRODUCTION The use of scrap mica as an industrial raw material has grown rapidly during the past two decades. Demands by various industries for ground mica for use in the roofing, paint, rubber, plastics, and wallpaper trades as well as for less extensive uses in insulation, oil-well drilling, welding, pipeline enamel, decorative material, and for other purposes exceed present (1947) supplies.A small proportion of the raw material used comes from the Black Hills of South Dakota, where casual recovery has been practiced in the exploitation of pegnatite deposits for more valuable minerals. The annual production of scrap mica in the Black Hills for the years 1939 to 1946 is shown in figure 19. 4/Although small, this production of scrap mica materially augments the incomes of numerous operators.Volume production of mica would offer attractive opportunities for obtaining steady and more economical supplies of the rare minerals as byproducts. Appreciable supplies of beryl, lithia minerals, sheet mica, tantalite-columbite, and cassiterite could accrue. Furthermore, a stable scrap-mica production would complement the production of quality feldspar, for which the Black Hills pegmatites are noted, and would help balance the economy of pegmatite mineral production.Mechanical methods of separation are requisite to production of enough scrap mica to be generally profitable. Various phases of the characteristics end treatment of mica have been investigated by the Bureau of Mines. A bibliography of these reports is appended.In 1945 the Bureau of Mines conducted pilot-plant tests to recover scrap mica by selective screening of crushed pegmatite. More recently the problem has boon studied in the Pegmatite Research Laboratory to aid in developing technological methods by which scrap mica may be separated from crushed pegmatite."

Feb 1, 1949

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003

By N. L. Wimmler

The chromite deposits along the Stillwater complex in Stillwater and Sweetgrass Counties, Mont., have at various times been studied and reported on by the Federal Geological Survey, the Montana Bureau of Mines and Geology, other Government agencies, and private interests, Several of the deposits were explored to a mall extent by the owners during the World War of 1914-17, but no production resulted. The importance of these deposits and the urgent necessity of developing large domestic sources of chromite were realized shortly before the beginning of the recent World War. These deposits were therefore investigated and developed by Government agencies and., as a result, now afford the largest known reserves of chromium in the United States. In 1939, under the authority of the Strategic Minerals Act, the Bureau of Mines and the Geological Survey made preliminary investigations of these deposits. As a result, the Bureau of Mines conducted an extensive program of trenching, diamond core drilling, and sampling. This work was begun in August 1939 and continued to April 1943. The Bureau of Mines also performed numerous metallurgical tests on the beneficiation of the chromite ores and concentrates and for the production of chromium metal there from. Research continues as a means toward utilizing these ores.

Jan 1, 1948

By E. G. King

Thermodynamic calculations involving the oxides of tungsten and molybdenum have been hampered by lack of accurate entropies and high temperature heat contents. This paper presents work by the Federal Bureau of Mines on new low-temperature heat-capacity data leading to the evaluation of the 298.15° K. entropies of tungsten dioxide and tungsten trioxide, as well as high-temperature heat contents (above 298.15° K.) of molybdenum dioxide, molybdenum tri-oxide, tungsten dioxide, and tungsten trioxide. Included are heats of fusion of the two trioxides. The heats of formation at 298.15° K. of these four oxides are tabulated as measured by Mah4 5/ of this laboratory. Included also are the 298.15° K. entropy of Mo02 measured by Kin 6/ of this laboratory, and that for Mo03 according to Kelley and King.7/ These basic data provide a consistent compilation from which to perform accurate thermodynamic calculations involving these compounds. No previous low-temperature- heat-capacity measurements have been reported for tungsten dioxide. Seltz, Dunkerley, and DeWitt8/ measured the low-temperature heat capacity of tungsten trioxide. The only previously-reported high-temperature heat-content measurements for any of the oxides were conducted by Cosgrove and Snyder,9/ who measured molybdenum trioxide to 1,300° K.

Jan 1, 1960

By Gregory R. Wagner

The Program of Mine Safety and Health Research described in this document reflects the continuing commitment of the Spokane and Pittsburgh Research Laboratories to focus on the most important areas where research can make a difference in reducing risk and improving safety and health for miners. It is the first program of work conducted since Congress mandated closure of the former U. S. Bureau of Mines (USBM) in the Department of the Interior and supported integration of the health and safety research function of the former USBM into the National Institute for Occupational Safety and Health (NIOSH). Organizational changes made FY97 a challenging year of transition. Ongoing research was reviewed and revised to reflect the new, more limited, health and safety mandate of the research laboratories. The mining industry, mine worker representatives, and interested government agencies provided broad input to assure that the research performed would focus on the most critical safety and health problems confronting mining today and which are expected to be faced in the future. The two laboratories worked to evolve coordinated programs of safety and health research, each with a special focus. The work of the Spokane Research Laboratory is directed toward issues of special importance to the Western mining industry, particularly those safety hazards found in metal/nonmetal mining and surface mining. The work of the Pittsburgh Research Laboratory will continue to focus on Eastern mining, particularly underground coal mining. Traditional areas of expertise for understanding and preventing fires and explosions and for controlling the hazards of dust and noise will continue to reside in Pittsburgh. Each laboratory is developing new capabilities in the analysis of relevant safety and health information to assure that program priority-setting decisions are informed by the best available data. Recognizing the continuing importance of communicating the results of research to all who are capable of improving safety and health conditions in mining, each laboratory has developed an activity for information dissemination and coordination with stakeholders. In the midst of organizational self-examination and change, the research staff in Pittsburgh and Spokane have never wavered from their continuing commitment to conduct the highest quality scientific research-solution-oriented scientific work meant to reduce the risk of injury, disease, and death from occupational hazards in mining. The pages that follow give insight into some of the program activities and accomplishments from FY97. I hope you share my pride in the many accomplishments of the NIOSH mine safety and health research program during this year. This report comes at a time of increasing stability for the mine health and safety research program. The organizational changes in Spokane and Pittsburgh have been concluded, and NIOSH has succeeded in recruiting a new, permanent associate director for mining to lead this critically important national program. Congress has contributed to an optimistic future by providing expanded funding for NIOSH mining-related research for the next fiscal year. On a personal note, I greatly appreciate the opportunity I have had to serve as the NIOSH Acting Associate Director for Mining during this transitional year. The commitment and intelligence with which the mining research staff pursued their mission was matched by their patience and understanding in moving into a new organizational environment. All of us committed to improved safety and health for this Nation's miners owe them our respect and appreciation.

By A. D. Hahn

This report describes and gives the results of an examination by the Federal Bureau of Mines of ilmenite-bearing placer sand deposits in the 24-mile long valley of Otter Creek, Kiowa and Tillman Counties, Okla. Drilling and sampling was completed in three periods between October 1956 and September 1957. Mineralogic studies and mineral-dressing tests on recovery of ilmenite and other heavy minerals from composited samples of the sands were made in Bureau of Mines laboratories at Rolla, Mo., in 1957 and early 1958. Otter Creek rises in and drains the southwestern extremity of the Wichita Mountains, which are represented locally by knolls and ridges of gabbro and granite surrounded by plains floored with flat-lying Permian red beds. The valley fill consists of a basal sand-clay component, derived from weathering of the igneous rocks, and an overlying silt-clay alluvium. Ilmenite is present in significant quantity and recoverable grain size only in the basal sand-clay.

Jan 1, 1960

By D. B. Dow

"In the natural-gas Gasoline industry, the methods used in determining the amount of gasoline in natural gas are many and varied; they include the specific-gravity test, laboratory tests involving absorption, charge in volume of the gas or in the absorption medium, absorption in charcoal with subsequent distillation, compression of the gas which results in the condensation of the gasoline, and the absorption of the gasoline vapors in an absorption oil, from which the gasoline is distilled and measured. Each of these various tests has advantages, and disadvantages. It is however, conceded in the industry that the tests in which the gasoline is obtained and measured as such are the more reliable.This paper deals with certain factors which should be considered in making absorption tests using ""mineral seal oil"" as an absorbent; this method of testing is widely used not only in the field, but in control work in absorption gasoline plants where the gasoline content of the intake and discharge gas is determined daily. In control work it is frequently found that the plant produces more gasoline than the tests show, which gives the plant the appearance of making more gasoline than is actually present in the gas treated, or in other words operating at more than one hundred per cent efficiency. Obviously then, the tests as made in these cases are in error, and in hope of correcting some of these variances, the following factors have been studied at the U. S. Bureau of Mines petroleum station at Bartlesville, Oklahoma."

Aug 1, 1920