Search Documents

By L. A. Panek, A. J. Barry, John A. McCormick

"INTRODUCTION During recent years, roof bolting has become widely accepted as a systematic method of supporting both coal- and metal-mine roofs. Today, over 2 million roof bolts are installed monthly. Most of the information on bolt installation procedure reported to date (1,2,3,4,5,6) 3/ has been obtained by trial and error by individual groups or operators. To insure good roof control, experience and field tests have indicated that roof bolts should be installed immediately after the exposure of new roof, and they should be preloaded enough to minimize sag of the roof over the opening. The question of the proper initial preload for roof bolts is under study, although it is a general practice to impose an initial load on a bolt of approximately 10,000 pounds. This created a problem of measuring bolt loads at installations in underground mines, which was partly solved by using a commercial-type torque wrench; a device that permits a direct reading of the torque applied to the nut on a roof-bolt assembly from which the corresponding load can be determined by referring to specifications furnished by the manufacturers. However, considerable apprehension was expressed regarding the accuracy of this measuring procedure because of variations in the manufacture of roof-bolting materials and the degree of care exercised in making bolt installations. In the process of loading a bolt, only a small part of the effort is expended in producing strain in the bolt - the larger part of the effort is used in overcoming frictional effects in the nut-bolt-washer assembly. These frictional effects are subject to many factors, such as condition of threads, type of lubrication, if any, the finish on the nut and bearing plate, and the alinement of the bearing plate on the bolt. The object of this investigation was to determine the accuracy with which the load developed in a slotted-type roof bolt installed in a conventional manner in shale or sandstone roof rock can be determined from the torque applied to the nut.This report is the first of a series relating to basic research in roof bolting in underground mines. A future report will cover results obtained using expansion-type bolts under similar conditions. Other reports will consider the efficiency of bolt anchorages, the long period stability of bolts, and the design of safe and efficient roof-bolting systems."

May 1, 1953

By Clyde L. Brown

Recent developments in portable communication equipment for use in emergency recovery work following mine fires and explosions have wade possible a convenient and dependable means of directing rescue teams working under hazardous conditions. INTRODUCTION Mine rescue and recovery operations following; fires and explosions are frequently conducted under adverse conditions that require the use of oxygen breathing apparatus by members of a 5- or 6-man team. Conventional apparatus used for this purpose for many years was equipped with an oxygen supply adequate for at least 2 hours. The design of the apparatus is such that the nose passages are closed with a clamp, and breathing is accomplished through a mouthpiece connected to the apparatus by tubes and arranged to prevent inhaling air or gases from outside sources. The use of the mouthpiece has presented difficulties in the development of telephone communication because of the wearer's inability to speak while wearing the mouthpiece. The method of conducting operations of rescue teams requires a person to direct operations at a fresh-air base as close to the rescue team as possible. At least one standby rescue team and 2 or 3 other persons assigned to various tasks are stationed at the fresh-air base. An efficient and reliable means of communication between the director of operations and the rescue team is necessary for reasonably safe and efficient work in hazardous areas.

Jan 1, 1957

By E. R. Palowitch

This report stems from a study by the Bureau of Mines of the possibility of reducing coal filter-cake moisture by applying radiant heat directly to the filter cake while under vacuum during the drying phase of the filter cycle. One disk of a 4-foot-diameter vacuum filter was equipped with gas-fired radiant-heat generators and the effect of radiant heating on the moisture content of a variety of filter cakes was studied. The results of this investigation show that this process can best be described as a filter aid capable of increasing the effectiveness of conventional filtration approximately 6 percentage points of moisture. The operating cost of removing water by this method is somewhat lower than the average operating cost of thermal drying and is considerably cheaper when the total cost is considered. Removal of water from coal that has been wet-cleaned is an important part of the overall coal preparation process. Water is a contaminant, and it is foolish to wash coal to reduce its ash content and add inert water in the process. In some instances the removal of water is actually more important than the removal of ash-forming minerals; its weight adds to the cost of transportation, and its evaporation during burning or carbonizing absorbs useful heat. Fine coal that contains more than about 10 percent moisture is notoriously difficult to handle. A problem thus exists for which there are sound practical and economic reasons to seek a solution.

Jan 1, 1961

By Launa G. Mallett, Charles Vaught, Dana C. Reinke, Lisa J. Steiner, Lynn L. Rethi, Kathleen M. Kowalski-Trakofler, Jr. Brnich, William J. Wiehagen

Safety and health professionals recognize that training is a critical element of any effective safety and health program. An extensive literature survey has led the authors to conclude that we are at the beginning of a revolution in training due to changes in the demographics of the workforce, the rapid growth of technology, and the universal ascendance of the information age. Of present major concern in the mining industry is how to provide appropriate training for an aging workforce and concurrently develop training for the expected influx of new and less experienced miners as older workers retire. This report explores the key issues in the changing safety and health training area as identified by the multidisciplinary team of NIOSH researchers who conducted the literature survey. Issues include generational differences between newer mine workers and the present workforce with respect to their physical, psychological, social, and cultural characteristics; their learning styles and work expectations; and the impact of technology. Some preliminary conclusions are offered for future training needs.

Jul 1, 2004

By C. P. Mishra

The Bureau of Mines performed a study of the availability of cobalt from market economy countries. The study entailed the detailed analysis of 97 deposits which contain 3.9 billion lb of cobalt at the demonstrated level; in 94 of the deposits cobalt is recovered as a byproduct, and in 3 it is considered the primary product. Since 97 pet of all recoverable cobalt is derived as a byproduct from copper and nickel deposits, the report focused on these two sources. At an assumed market price of $0.89flb for copper, $3.45/lb for nickel, $475/tr 021 for platinum, and $7/lb for cobalt, 1,330 million lb of cobalt at the demonstrated level are potentially available. This total includes 1,105 million lb of cobalt from copper properties, 190 million lb from nickel, 29 million lb from platinum, and 6 million lb from primary cobalt. This analysis indicates that the production cost for 589 million lb of cobalt can be totally covered by the revenues obtained from the other metals produced. The impacts of increases in capital investment and energy costs are also discussed.

Jan 1, 1985

By John W. Kopp

Stemming is used in blasting operations to help contain explosive gases as long as possible. Stemming can reduce airblast, improve fragmentation, and reduce the chances of hot explosive gases igniting methane and dust explosions in underground mines. Stemming is required in underground coal mines but is generally not used in underground metal and nonmetal mines. Some underground metal and nonmetal mines are classified as gassy and can require special blasting procedures such as the use of stemming to minsure the safety of miners. The types and amounts of stemming material that are desirable in underground metal and nonmetal mine blasting to ensure good or improved fragmentation while containing the hot gases are largely unknown. This Bureau of Mines research examined the effectiveness of differing lengths of stemming by measuring stemming ejection times as related to burden movement. With properly stemmed blasts, stemming is contained until some burden movement has occurred. Test blasts at two surface limestone quarries were evaluated using high-speed photography. For the conditions of these tests, a stemming length of at least 26 charge diameters was found to prevent premature stemming ejection. In tests with stemming lengths of 16 charge diameters, the stemming was effective but there was early venting of hot gases through fractures in the rock. Further testing with other rock types, hole diameters, explosive types, and stemming materials as they affect incendivity is recommended.

Jan 1, 1987

By J. A. Cavallaro

The heats of formation of anhydrous barium carbonate (witherite), strontium carbonate (strontianite), and lead carbonate (cerussite) were determined by solution calorimetry. The solution mediums were hydrochloric acid for barium and strontium carbonates and perchloric acid for lead carbonate. The heats of formation at 298.15° K are as follows: BaCO3 -297.5 ± 0.8 kcal/mole; SrCO3 -294.6 ± 0.5 kcal/mole; and PbCO3 -168.0 ± 0.3 kcal/mole.

Jan 1, 1966

By W. K. Cunningham, Edwin A. Gee

"INTRODUCTION This paper is one of many reporting on various aspects of the Bureau of Mines program during World War II directed toward alleviation of shortages in certain critical minerals some of these papers are published as technical papers information circulars, and reports of investigations, of the Bureau of Mines or in technical journals.The investigation described in this report was begun as part of the Bureau, of Mines program to develop acid processes for the extraction of alumina from low-grade bauxites and clays. A domestic shortage of high-grade bauxite suitable for treatment by the Bayer process became acute as a result of World War II; and intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted.A survey of the various methods for extraction of alumina from clay has been presented in an early Bureau of Mines publication. 4/ The principal barrier to the successful operation of an acid process has been the difficulty experienced in developing a suitable commercial method for purifying the crude aluminum salts after the clay extraction is complete. Iron salts are the foremost contamination influence. A review of the more prominent procedures that have been proposed for separating iron and aluminum salts can be found in the well-known text on aluminum by Edwards, Frary, and Jeffries. 5/The majority of acid processes to extract alumina from clay employ sulfuric acid as the leaching agent, and the purification is thus reduced to the separation of iron and aluminum, sulfates."

Feb 1, 1948

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940

By R. S. Dean

"INTRODUCTION The idea of direct steel is by no means new. Although the work of Bessemer and Siemens provided simple and effective moans for converting pig iron into steel and established the ""blast-furnace route"" as the almost universal method of producing steel, metallurgists have not ceased to dream of direct steel. By direct steel is meant any process by which iron oxide in ore is reduced to Iron of the same or greater purity than the final steel or wrought iron. That is, carbon or alloying elements would be added as needed, not reduced in unwanted quantities into the iron and then removed more or completely by refining (Bessemer or open hearth) only to be readded in desired quantities.In general, direct-steel processes are ""sponge-iron"" processes, because reducing iron oxide without simultaneously alloying the iron with carbon, phcophorus, sulfur, and silicon present in ore and fuel succeeds only if the temperature is below the melting point of the iron. Such solid iron formed by reduction of iron oxide at relatively low temperature is sponge iron, which is butlery and porous. When the reduction proceeds at the higher temperature at which the particles of metal can weld together or finally even melt to yield pellets or balls that do not have the porosity and low-density characteristic of sponge iron, the product might preferably be called simply ""direct iron."""

Jan 1, 1945

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By J. M. Riley

A fluorometric method using morin in an alkaline-buffered chelating solution has been developed by the Bureau of Mines for determining beryllium in ores and mill products. Apparatus for measuring fluorescence intensities of the beryllium-morin reaction is described. Preparation of the sample for analysis consists essentially of digestion with sulfuric, nitric, and hydrofluoric acids, fusion of the residue with sodium carbonate and sodium borate, Solution of the melt with sulfuric acid, and proper dilution. Chemical separation of other ions is usually unnecessary. The method rave reliable beryllium determinations on samples in the 0.01- to 0.37-percent BeO range. The method is particularly applicable to low-grade beryllium ores; however, semiquantitative beryllium determinations have been made on beryl containing 12.0 percent BeO.

Jan 1, 1956

By Friedel. Michael J.

The U.S. Bureau of Mines investigated acoustic emission (AE) and the Kaiser effect in six types of rock: St. Cloud gray granodiorite, Barre granite, Dresser basalt, Salem limestone, Berea sandstone, and a volcanic tuff. AE signatures were used for interpreting the rock deformation stage and for indicating mechanisms of failure in uniaxial compression. The research demonstrated the advantages of using the volumetric stress-strain curve, as opposed to the more conventional uniaxial curve, for correlating AE response signatures with deformation stages and fracture processes in the rock. Standardized experimental procedures were used for the AE monitoring. The Kaiser effect was shown to be capable of determining prestress levels to within a few percentage points in uniaxial compression tests. Also, prestress memory was shown to be retained in the rock for periods of up to at least. 5 months, the maximum period of testing. The Kaiser effect AE technology holds promise for providing a comparatively inexpensive and less complex method for examihing stress history in rock. However, since the conftning stress has a pronounced influence on the Kaiser effect, it must be considered in developing technology for determining peak fteld stresses based on the Kaiser effect.

Jan 1, 1990

By D. Harrington

The record of fatalities from mine explosions during the past 2 fiscal years has been anything but encouraging; more men were killed by explosions (379) than were killed from the ante cause during to' preceding 6 years combined (368). The reason for the large increase in the number of explosion fatalities during the past 2 years as compared with the previous 6 years is not entirely clear. In some instances, there has been laxity in the enforcement of State mining laws; in others, both workers and operating officials is have failed to observe recognized precautionary measures to prevent explosions. In many of the explosions that lave occurred within the asst few years in mechanized mines it has been evident that speed of operation and a demand for maximum tonnage at minimum cost resulted in neglect of ordinary safety measures.

Jan 1, 1942

By G. W. Grove

The Joseph A. Holmes Safety Association acid the Holmes Association have fostered many chapters that have served as a medium in increasing safety in the mining industry. Details relating to the formation, operation, and achievements of the J. J. Forbes District. Council of the Holmes Safety Association, which operates in the Uniontown-Brownsville bituminous coal district of western Pennsylvania will be of interest to all who are striving to increase safety in mines, quarries, and in the oil fields. The Joseph A. Holmes Safety Association The Joseph A. Holmes, Safety Association' was organized in 1916 by 24 of the leading technical societies and mining organizations to perpetuate 'the memory of Dr. Joseph Austin Holmes, first Director of the United States Bureau of Mines.

Jan 1, 1929

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By E. P. Hayes

This report supplements the date contained in Bureau of Mines Information Circular 6156, "Special features of core drilling in the salt beds of Western Texas and New Mexico," by J. S. Wroth. That circular dealt with the drilling of the first 12 of the 24 potash tests made by the U. S. Bureau of Mines in cooperation with the U. S. Geological Survey; this report is concerned with the drilling of the last 12 tests. ACKNOWLEDGMENTS The writer is indebted to R. E. Heithecker, the Bureau of Mines engineer who had charge of the drilling of tests 13 to 17, for his well-prepared records on the drilling of these tests.

Jan 1, 1933

By J. L. Johnson

The U.S. Bureau of Mines investigated the recovery of tin and silver from the Coal Creek deposit in the Talkeetna Mountains, AK. Approximately 5 million st of reserves grading 0.2 pct Sn with silver credits of 0.2 tr oz/st have been delineated by drilling. A 10-to 25-pct Sn gravity concentrate was produced by treating the minus 20-mesh ore with a spiral, then regrinding to minus 65 mesh and tabling. Sulfide contamination in the gravity concentrate was as high as 60 pet. Sulfide flotation of this concentrate produced tailings containing 40 to 50 pet Sn. Overall recovery was 76 pct for tin but only 5 to 10 pct for silver because of losses during sulfide flotation. Other methods tested to clean the concentrate included cassiterite flotation, gangue flotation, nitric acid leaching, and wet and dry magnetic separation. Tin beneficiation tests on the minus 325-mesh fraction included cassiterite flotation, vanning, sulfide flotation, and fuming. The bench-scale and locked-cycle tests were used to estimate the mass flows for a 1,000-st/d plant.

Jan 1, 2010

By R. W. Lewis

The Federal Bureau of Mines Boulder City Metallurgy Research Laboratory conducted experiments in order to develop a spectrochemical method for determining the concentrations of impurities In high-purity tungsten. This report presents a procedure, developed by these experiments, for determining 19 impurities in high-purity tungsten. Metal samples were thermally converted to the oxide, mixed with graphite, which was prepared and mixed with an internal-standard element, and excited in a d.c. arc. Sixteen of the impurity elements were determined with one set of conditions, using germanium as an internal standard. Lanthanum was used as an internal standard in the tests for boron and chromium. Molybdenum required the substitution of sodium chloride for the graphite and the use of copper electrodes. Data on the precision of the method are included in this report. The coefficients of variation vary considerably but average about 15 percent. Higher concentrations of impurities than those investigated may be determined with some modifications of the testing procedure, provided attention is given to the possibility of interelement interferences.

Jan 1, 1961

By A. A. Berk

In the course of a study of the formation of external deposits on tubes in water-tube boilers it became desirable to determine the sulfur dioxide (SO2) and sulfur trioxide (SO3) in the Due gases. Determinations made by the A.S.M.E. method for SO2 and SO3 in gaseous products of combustion did not give accurate results. It was found that minute quantities of copper, present in the flue gases from the coal in use, caused oxidation of sulfite in the absorption bottle and that the carbon dioxide (CO2) in the flue gases caused high values for SO2. The A.S.M.E. test procedure was revised to prevent oxidation of sulfite in the absorption bottle and to allow for the effect of CO2; subsequent analyses of flue gases produced reliable results. The revised procedure is described.

Jan 1, 1950