Search Documents

By D. J. Stoops

The object of the research described in this paper was to investigate the effect of metallurgical and surface treatments on the corrosion behavior of arc-melted reactor-grade zirconium in cupric or ferric chloride solutions. An apparatus was constructed and specimens of various metallurgical conditions and surface treatments were tested for 6 days at 35° C., with aeration. Some correlations were observed between corrosion rate and the metal's condition and treatment, Specifically, the unattacked or least attacked specimens were those that had been etched as a final treatment before testing. The most severely attacked specimens were those that had been vacuum-annealed as a final treatment before testing. The moderately attacked specimens were those neither vacuum-annealed nor etched, but having a final surface treatment which left a cold-worked surface. Attack by cupric and ferric chloride was by pit- ting with no preference for grain boundaries, The corrosion scale was cow posed predominately of very fine zirconim particles, Particles from the FeC1,-corroded specimens were more pyrophoric than those from CuCl2-corroded specimens, and appeared to have a higher surface area to volume ratio. Comparison of results to those of previous investigators showed that at certain salt concentrations the more pure, reactor-grade zirconium was quite resistant to attack while the less pure, graphite-melted zirconium was severely attacked.

Jan 1, 1962

By Miller, ALEX U, Edward Thomas

In March 1937 the entire country was shocked by news of an explosion of gas in a New London (Tex.) schoolhouse, which resulted in the death of 280 pupils and 14 t eachers. The Government investigators of this disaster believed that the cause was the ignition and explosion of a large volume of explosive natural gas-air mixture that had accumulated in a poorly ventilated space beneath the first floor of the main school building and that this accumulation was due to leakage from gas lin suspended underneath the floor to carry the gas supply to the school.!i/ For some years there has been a potential explosion hazard in school houses and other buildings that are supplied with water from deep wells in certain parts of Illinois. Notwi thstand.ing the disaster at New London, Tex., and the fact that there had been gas ignitions at four water wells in different parts of the State, the explosion hazard in schools and other buildings was not fully recognized until a few months after the disaster in Texas, when an explosion occurred in the settling basin of the municipal water works of Clinton, Ill., and another in a pump house of the municipal water works in Normal, Ill, The explosion in the settling tank of the municipal water works in Clinton, Ill., occurred on August 12, 1937, and a.id considerable damage to the settling tank, but fortunately no one was injured. At the time of this explosion rapairs'and aJ.terations to the water plant were in progress, and 10 men were employed in the immediate vicinity of the settling tank. Two of these men were enlarging a hole in the concrete side with an air hammer for the installation of a larger discharge line.

Aug 1, 1938

By Eldon C. Pattee

THE BUREAU OF MINES began an investigation of tungsten resources of Montana in September 1953. This report presents information obtained from July 1955 to September 1957 on tungsten deposits in and near the Mount Torrey batholith. The batholith comprises part of the Pioneer Mountains of Beaverhead County in the southwest corner of Montana. Included in the report are assays and preliminary-examination data on 22 properties. Tungsten minerals are known to occur in 19 of the properties. The major producer is the Brown's Lake mine which has produced more than 625,000 tons of ore. Nearly all of the deposits are in the Lost Creek, Utopia, and Bald Mountain mining districts along the east and south margins of the Pioneer Mountains. The districts are less than 27 miles from Dillon, Mont.

Jan 1, 1960

By E. Morrice, R. D. Smith

Thermal expansion and electrical resistance measurements were made on cerium metal from 4° to 300° K. The apparatus developed , including a specimen holder and a cryostat system , are described along with the experimental techniques used in obtaining the measurements . The total linear thermal expansion Data at of 99.83 weight - percent cerium metal between 4 ° K and room temperature was 4.24 percent . The resistivity at 4° K was 7.0 x 10-6 ohm- centimeter . 4° K indicate a fundamental relationship between residual resistivity and purity of cerium metal . The effects of annealing and repeated thermal cycling on resistivity were determined .

Jan 1, 1964

By Robert F. Chaiken, Alex C. Smith

INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH) at its Pittsburgh Research Laboratory (PRC) is interested in the application of water mist sprays to extinguish diesel fie1 fires in underground mine diesel refueling areas. To this end experimental studies have been carried out on the extinguishment of diesel fuel fires at PRL's large enclosed fire suppression facility (FSP) at its Lake Lynn Laboratory (LLL). Two sizes of shallow fuel pans (3x3 ft and 5x7 ft) contained the fires, and a number of commercial mist spray nozzles (at roof locations) and spray/fire locations were tested (52 fires in all). Visual observations of the pool fire extinguishment process by the overhead sprays with an infra-red sensitive videocom suggests that there are two distinct actions involved in extinguishment due to two different transport mechanisms by which the water droplets can enter the fire plume. First, is a direct injection of water droplets into the plume from overhead. This is believed to involve larger water drops and leads to an extinguishment time of several minutes. Second, is an indirect injection process involving small water drops which are entrained in the sideways air flow that feeds oxygen to the fire. This second process apparently leads to relatively fast quenching of the fire in less than 1 minute - a highly useful attribute for a fire protection system. This paper describes a relatively simple parametric model for the indirect water injection process, and defines the critical spray conditions for achieving rapid quenching of the pool fire. While the model is consistent with the pool fire data obtained to date, the PRL studies are continuing with more complex pool fire scenarios. It remains to be seen if this simple parametric approach applies to these future fire tests. THEORETICAL Critical Drop Size In the two-dimensional representation of figure I, an oil pool fire is considered to be a cone whose base is the vaporizing liquid oil surface having an area n?, above which exists a fire plume diffusion flame) of height, L. The rising plume induces a horizontal air flow into the side of the plume supplying the oxygen necessary for propagating gas phase combustion reactions. Water droplets suspended in the air around the plume will tend to follow the horizontal air flows into the plume. The rate of air entrainment by the plume will be determined by the overall combustion reaction which is assumed to be

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about .5-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15, 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black, Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By d&apos, D. V. Andrea

Nine rock properties were determined for rocks coming from 49 locations and having a wide range of compressive strengths. Plots of the nine rock properties versus each other were prepared. A stepwise multiple linear regression analysis was performed to obtain several equations for predicting compressive strength. Both linear and curvilinear relationships were assumed between compressive strength and the other rock properties. The prediction equations had multiple correlation coefficients ranging from 0.947 for an equation with 1 variable (point load tensile strength) to 0.986 for an equation with 25 variables. Of the properties tested only point load tensile strength could be used alone to estimate compressive strength with fair accuracy.

Jan 1, 1965

By A. D. Garman

This paper presents one of a series of digests of foreign mining legisla- tion and court, decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Latin America has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers, to whom it is being referred through the courtesy of the Department of State. Individual abstracts of the laws of each of the countries herein discussed have been prepared and published separately. This general summary is presented for the use of mining engineers and investors whose interests extend over the borders of a single country. It is also designed to bring out certain general principles of mining law and, so far as feasible, to indicate the trend of mining legislation in South and Central America. In order to gain perspective, the details of legislation are not com- pletely covered in this paper, but an effort has been made to bring out essential differences as well as points of similarity in the laws of the various countries. The course of legislation is first traced chronologically and the points discussed are then arranged in tables in somerhat greater detail. .Si. With a very few exceptions the existing mining legislation of Spanish America is a development, of the Spanish "Law Decree of Bases" (more briefly referr- ed to as the "Decree-Bases") of 1868. This in turn was influenced, particularly in its classification of minerals, by the French law of April 21, 1810.

Jul 1, 1930

By John C. Edwards

The Bureau of Mines has developed a time-dependent mathematical model of radiative heating of bulkheads in mines. The model includes both reradiation from the duct (cylindrical) walls and direct radiation from the fire zone. Thermal loss into the wall of the duct and into the bulkhead is included. Both brick and wood bulkheads are considered. It is found that the heating rate of the system scales as the duct length-to-diameter ratio and the flame temperature. In particular, the time required for the irradiated surface of the bulkhead to reach a specified temperature decreases with increasing flame temperature for a fixed length-to-diameter ratio and increases with increasing length-to-diameter ratio for a specified flame temperature. It is also deter-mined that the time, T, for the bulkhead surface temperature to reach a specific value, Tb, for a fixed length-to-diameter ratio less than 4 and for a flame temperature of 1,200 K is approximately linearly dependent on Tb for 500 K < Tb < 700 K, and is nearly exponentially dependent on the length-to-diameter ratio for Tb = 600 and 700 K.

Jan 1, 1979

By W. J. Kroll

Despite the fact that barium minerals are plentiful and widely distributed in nature, this element is one that we do not yet know how to prepare cheaply in metallic form. This is due to its chemical activity, as evidenced by its great affinity for fluorine, chlorine, oxygen, nitrogen, hydrogen, and sulfur. Furthermore, it forms a very stable subchloride and subfluoride, which prevents isolation of the metal by fusion electrolysis from a halide bath. A good survey of the metallurgy of barium calcium, arid strontium has been made recently in Light Metals (54,55).3/ Metallic magnesium (46), calcium (83), barium, and strontium (27) reduce each other&apos;s oxides. Proof of this can be found in the activation of BaO after reduction with Mg, which leads to the formation of so-called "Maquenne" mixtures (58) used for absorbing gases. However, it is impossible to extract the reduced metal- from the residue, a fact that Guntz (25) attributed to the formation of barium suboxide. There is no necessity for presuming the formation of such a compound, as it has boon established that in the reduction there is always formed an alloy of the alkaline-earth metal with the magnesium, which is capable of producing hydrogen when brought into contact with water. The reduction of alkaline earth-metal oxides with aluminum was observed by Mallet (57) in 1877, but recent investigations have shown that the end product of the reaction is an alloy of aluminum with the alkaline earth metal (1,2). Silicon also has been suggested as a reducing agent, and the results obtained are the same (84,85).

Jan 1, 1945

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

By Robert L. Lappi

Volume I of this report described the demonstration of cross-ridge mountaintop coal mining. This document, Volume II, is intended for use as a supporting document to Volume I. This report describes the MATHMINE Mine Simulation System, a modularized software system used to support the demonstration of cross-ridge Mountaintop coal mining. The MATHMINE Mine Simulation System was used to generate mine plans for coal extraction at lowest cost. The functional details, data requirements and output of the software system are detailed here. The computer program was written in FORTRAN. One module which generates resource location data required the use of SAS?.

Jan 1, 1984

By d&apos, Dennis V. Andrea

The Bureau of Mines and El Paso Mining and Milling Co. conducted a cooperative in situ leaching research program at the Emerald Isle mine near Kingman, Ariz. The objective of this research was to develop in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 3,000,000 tons of ore under 200 feet of overburden adjacent to the pit. The research included core drilling for fragmentation analysis, inplace permeability testing, seismic surveys, blasting tests, blast vibration measurements, inplace leaching, and ground water monitoring. A l5,000-ton test area in the pit bottom was blasted and leached inplace for 117 days. This successful test was followed by leaching 100,000 additional tons of unblasted pit bottom ore. Two test blasts, under 205 feet of overburden and extending to 290 feet, were detonated in an area near the open pit. The second blast was detonated because the first blast did not create adequate permeability for leaching. Pit bottom leaching was discontinued and the test area under 200 feet of overburden was not leached because the company terminated operations at the Emerald Isle mine. Based on the research completed, an expanded in situ leaching system was designed, but not implemented, to recover copper from a 1,500,000-ton area at the Emerald Isle mine.

Jan 1, 1977

By L. J. Kane

Several processes being developed by the Federal Bureau of Mines to provide new and more efficient uses for coal require practical methods for removing dust from hot gases. Filters provide such means. The efficiency of filters made of aluminum silicate fibers and porous stainless steel was determined. The results obtained with the fibers were previously reported.5 In this investigation tests were made with three porosities of stainless steel filter material (grades C, D, and E) at a gas flow of 1,000 std. c.f.h./sq. ft. of filter, temperatures of 75° and 1,000° F., and dust loadings (as represented by cumulative dust fed) of 100, 1,000, and 10,000 gr./sq. ft. of filter. Pressure drop during the runs ranged from 0.1 to 21 in. of mercury, and dust removal from 25 to 99.93 pct. Filters having the finest pores gave the greatest pressure drop and percentage of dust removal; however, their dust-holding capacity was slightly lower. Usually, their ability to remove a higher percentage of dust at the same pressure drop more than compensated for the slightly lower dust-holding capacity. With increase in temperature, for the same weight rate of flow of gas, the pressure drop increased and the percentage of dust removal decreased. The effect of temperature was probably due to the accompanying change in the linear velocity and viscosity of the gas.

Jan 1, 1961

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976

By A. G. Starliper, H. Kenworthy

A procedure was developed for the separation of lead and sulfur in industrial concentrates of galena by a combination of chlorination and fused - salt electrolysis . Galena could not be satisfactorily electrolyzed in the various media tried ; however , when it was treated with chlorine the resulting lead chloride could be effectively separated electrically into lead and chlorine . An apparatus was designed and constructed to chlorinate galena and to volatilize simultaneously most of the chloridized impurities . By electrolyzing the chlorinated concentrate , a high percentage of lead was recovered . Anodic chlorine was drawn from the cell and was used to chlorinate new feed . In many runs , the recovered metal analyzed from 99.8 to 99.9 percent lead . Lead was also distributed as a chloride in the bath , and a small portion was in the volatile fraction produced during the chlorination step . During a tinuous operation , only 0.1 percent of the total lead was discarded ; 99.9 percent was accounted for in the metal , electrolytic bath , and washed or leached chlorination condensate which was essentially lead chloride . About 95 percent of the sulfur from the galena was recovered as a byproduct of over 90 - percent grade .

Jan 1, 1964

The Anaconda Copper Company reportedly reached an exclusive agreement with Cook Inlet Region, Inc., to explore 24 million acres in south-central Alaska and to share equally with Cook the proceeds of any mineral discovery. According to an Anaconda geologist, "the company is anticipating, based on geologic testing, that it will find significant deposits of copper, lead, and zinc. There is also evidence of the presence of precious metals such as silver and gold, and also strong evidence of strategic minerals such as chrome, platinum, tin, and nickel." Cook Inlet Region, Inc., is owned by 6,500 Alaskan natives. Chile, which has a growing, free-market economy under President Pinochet, reportedly will no longer require companies to obtain prior governmental approval for the exploration and development of new mines.

Jan 1, 1981

By F. H. Gibson

An investigation was made by the Federal Bureau of Mines of methods for determining phosphorus in coal, coal ash, and coke ash. Several of these methods are being considered for international standardization. As might be expected, methods and proposals from other countries for determining phosphorus differ considerably from those accepted an standard in the United States. Some of the methods differ fundamentally in principle from the American Society for Testing Materials (ASTM) standard used in the United States; others differ only in details of procedure. Because the Bureau considered that certain of the proposed methods might offer advantages in obtaining increased accuracy and precision or in decreasing the time required for making analyses, these methods were investigated, and the results compared with those obtained by the ASTM method. The methods investigated may be grouped into three types--volumetric, colorimetric, and gravimetric. All were about equally accurate and may be used alternatively. From a practical viewpoint, when only a limited number of analyses are made intermittently, the gravimetric procedure probably is the most suitable because no special apparatus or standard solutions are required. The volumetric methods are more rapid when more analyses are made. For mass production, the colorimetric methods, although requiring a suitable photometer or spectrophotometer, are more suitable because a large throughput should be feasible.

Jan 1, 1961

By H. C. Fuller

Depletion of iron ore in the Nation&apos;s large deposits has directed attention to other sources. One of these is the titaniferous iron ore of the Iron Mountain, Wyo., area. Tests were made to determine the feasibility of smelting this ore, which contains about 20 percent titanium dioxide (Ti02), in an electric-arc furnace to produce pig iron. Initial tests, which were made in a 30-pound-capacity induction furnace, demonstrated that the iron could be easily reduced to metal and that limestone was a suitable and effective flux. Larger scale tests then were made in a 50-pound-capacity electric-arc furnace to obtain the more detailed information necessary for the planned continuous operation of a still larger arc furnace. The principal facts determined by preliminary batch-smelting studies were that (1) 9 pounds of limestone flux was required for each 100 pounds of ore smelted, (2) expensive coke was not required because coal proved to be a satisfactory reductant (near stoichiometric carbon was optimum), and (3) overreduction, which produced a viscous slag, must be avoided.

Jan 1, 1961