Search Documents

By Lloyd Williams

1. Reserves have been estimated for three coal beds in Bledsoe County, Tenn.: Morgan Springs, Lantana, and Sewanee. The Richland and Nelson beds occur in Bledsoe County also, but there was not enough information on them for making an estimate of reserves. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated at 43 million tons as of January 1, 1954. Of this total, 22 million tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves deter-mined by this investigation.

Jan 1, 1956

By Robert H. Essenhigh

A stirred reactor (SR) combustion system has been developed to gather information on the mechanisms of ignition and flame propagation of coal dust under conditions similar to those found in coal dust explosion flames. The prime scaling variable considered in this study is that of rapid particle heating (between 105 and 106°K/sec) which is accomplished by means of turbulent mixing during combustion. The SR combustors tested in this study have consisted basically of spheres hollowed in the centers of refractory housings. Coal and air mixtures have been injected into the spherical combustion chambers through a single jet, two opposed jets or four opposed jets. The diameters of the jets have ranged from 0.63 to 0.22 cm. The volumes of the combustion chambers have ranged from 1.0 to 0.2 liters. The reactors have been equipped with thermocouples embedded in the combustion chamber wall as well as a thermocouple located in the exhaust gas stream. In the latter versions of the SR, provisions were made for both solid sampling and gas sampling of the reactant stream exiting from the combustion chamber. Experiments have been carried out using pulverized bituminous coal. The coal has been reacted in an SR in mixtures of air and air/nitrogen. These experiments have provided information on the mode of ignition of the coal as well as yielding information on the kinetics of coal pyrolysis through the use of SR theory. Ash tests performed on the reacted samples collected from the SR indicated that the majority of the values of weight loss percentage were between 60 and 70 percent. The percentages of weight loss were relatively unaffected by changes in temperature which varied between 1100 and 1700°K and by changes in residence time which varied between 10 and 20 millisec. Volatile matter tests performed on the samples indicated that the volatile matter left in the char ranged from 3 to 20 percent of the original content. By assuming that all the mass loss was due solely to pyrolysis with no combustion occurring at the particle surface, Q-factors for each test have been calculated. The results of these calculations indicate an average value of Q equal to 1.88. This finding shows that the majority of mass loss can be attributed to pyrolysis. The fact that the extent of reaction varies only slightly over the range of test conditions has been examined in the context of the two component hypothesis of coal constitution. This approach leads to the conclusion that the reaction of the "easily evolved" component VMI is extremely rapid and that the majority of it is removed from the coal in times less than the residence time in the system. This means that the volatile residue remaining in the char can be considered to consist of component II, VMII. If the mass fraction of VMI = 0, then an activation energy of 18.0 kcal is obtained for the pyrolysis reaction. If the mass fraction is assumed to be 0.75, the activation energy increases to 31.2 kcal.

Jan 1, 1978

By Ernest W. Johnson

In most underground iron mines in the Lake Superior district the active workings are at considerable depth. When additional openings into such. nines are needed, operating officials are eager to discover more efficient methods of constructing them. In recent years, openings into two mines in the district were made by the borehole method,-which employs chilled-iron shot as the cutting medium. Others were made by the churn-drill method, in which pilot hole is churn-drilled and subsequently reamed to a desired but relatively small diameter. Both methods are comparatively new and unique, at least in some phases and in their application.

Jan 1, 1946

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been puplished5/ describing apparatus and tests made on anthracite to determining the amount and composition of the oxidation products when normal dry air was passed through it at temperatures varying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative prorortions varied with the temperature. From: these results, graphs were prepared by which `he temperature at which the coal was oxidized could 'be estimated, thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By L. D. Schmidt, Wm. Seymour, W. S. Landers

"INTRODUCTION The relative value of the various individual physical and chemical properties of coke as a measure of its performance in the blast furnace as aroused considerable controversy but it is generally agreed that uniformity in these properties is extremely important if maximum mum pip-iron production is to be attained. The control of,the bulk density or weight per cubic feet of the coal charge in the coke ovens is a major, and frequently overlooked, factor in producing a uniform product and in efficient operation of the coke plant.This report presents a brief discussion of the general problem of bulk-density control and the results of tests on samples of coke-oven charges from several operating plants experiencing difficulties due to lack of adequate control. These tests covered the effect of moisture and oil content on the bulk density of the coal. Some tests on the effect of a wetting agent and furnenous of gained were also made. A description of the methods used to determine the bulk density of the coals studied in this investigation and of the methods used to apply oil to the coal at byproduct-coke plants are included in this product. No theoretical analysis of the data presented in this report, because the primary purpose of the investigation was to obtain data of immediate practical value to the plants concerned."

Apr 1, 1945

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been published5/ describing apparatus and tests made on anthracite to determine the amount and composition of the a oxidation products when normal dry air was passed through it at temperatures varrying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative proportions varied with the temperature. From these results, graphs were prepared by which the temperature at which the coal was oxidized could be estimated thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By W. L. Crentz

Before Korea was partitioned along the 38th parallel following World War II, the coal fields of South Korea, with the possible exception of the Samchok area, were not considered important to the industrial needs or Japan or Korea. Much of the demand for electric power in South Korea was met by hydroelectric installations north of the 38th parallel. Following cessation of hostilities between Japan and the' Allied nations in 1945, hydroelectric power continued to flow into South Korea from the north until 1949, when the North Koreans severed the power lines into South Korea, thereby forcing that section of the country to depend almost entirely upon coal to generate electric power.

Jan 1, 1953

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

By Maria I. De Rosa

The U.S. Bureau of Mines conducted experiments for predicting materials' ease of combustion (smoldering onset, smoldering, flaming, and decomposition rates) by means of submicrometer smoke particle characteristics for the development of a simple test method. The experiments were carried out in an approximately 20-L furnace, with a 10-L/min airflow through the furnace for a 14-min duration, at set furnace temperatures of 150°, 250°, and 1,000° C. The variables studied as a function of time were the onset time of smoke particles, time and duration of maximum smoke particle generation, average concentration of smoke particles, and particles' average diameter, mass weight loss, and furnace temperatures. Results show that the onset time of smoke particles is predictive of materials' ease of smoldering, and the time of maximum smoke particle generation and its duration, coupled with mass weight loss, are predictive of materials' ease of smoldering and flaming (depending on the experimental temperatures), and decomposition rates.

Jan 1, 2010

By C. M. Flynn

The solubilities of sideronatrite [Na2Fe(OH)(SO4)2?3H20] and ferrinatrite [Na3Fe(SO4),&apos;3H2O] were determined by the Bureau of Mines in the Na2SO4-Fe2O3-H2SO4-H20 system at 25°, 40°, 60°, and 90° C. The solution compositions investigated ranged from Na+-Fe&apos;+ mol ratios of 0.5 to >100 (Na2SO4 saturation) and H+ -SO4 2-mol ratios of 0 to 1. O. The results are presented in the form of contour plots. The solubilities were determined by seeding supersaturated solutions of known composition with the specified solid phase to precipitate a substantial amount of solid. Water was then added in small portions to the solution until the last portion of the solid dissolved. Equilibration times at 25°, 40°, 60°, and 90° C were 2 days, 1 day, 8 to 16 h, and 2 to 4 h, respectively. The accuracy of the solubility data is estimated to be 1 to 2 pet. Low iron solubilities of <0.36 pct Fe2(SO4)&apos;, or 1 g Fe/kg solution, were obtained in solutions containing at least 8 pet Na2SO4 in the absence of H2SO4 or a total of at least 36 to 38 pet Na2SO4 + H2SO4 at high acidity. The filterability and density of sideronatrite and ferrinatrite in comparison with other iron compounds are reported. These compounds are suitable vehicles for iron removal in Na2SO4-rieh solutions. Additional solubility data on the Na2SO4-H2SO4-H20 system were also obtained.

Jan 1, 1987

By John Durkin

The Bureau of Mines has conducted field studies in coal mines through- out the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above mines throughout the coalfields. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10-pct false alarm rate, the expected probability of detecting a miner&apos;s signal from a depth of 1,000 ft is 54 pct; at 500 ft it is 95 pct. These depths exceed the actual depths of 90 pct and 50 pct, respectively, of U.S. coal mines. Sensitivity studies have shown that at a depth of 1,000 ft, for every 3 db of improvement in signal-to-noise ratio, the probability of detection increases 6 to 8 pct.

Jan 1, 1982

By E. P. Youngman

The basic mining law of French Morocco is the Edict of 1914, "Danir of Jamary 19, 1914, for the Regulation of Mineral Prospecting and Exploitation in the Zone of the French Protectorate of the Cherifien Empire," which, as the preamble states, was promulgated at the instance of the Director General of Public Works, in consideration of the fact that mines constitute one of the sources of wealth of the Empire. According to a consular report, dated May 18, 1923, by Bradford, men- tioned above, the mining industry of that country, aside from the exploitation of the extensive phosphate deposits, can scarcely be said to exist, but the potential field for mining is promising. However, no large-scale exploitation of the mineral wealth of French Morocco can be hoped for until there is complete pacification of large areas that are still in an unsubdued state or until adequate transportation facilities, scientific prospecting, and large investments of cap- ital are assured. An edict in 1920 (Dahir of January 27, 1920) modified the law mentioned above by declaring the prospecting for and the exploitation of phosphates to be exclusively reserved to the Government. The Dahir o. August 7, 1920, announced the creation of the Cherifien Phosphate Office (Office. Cherifien des Phosphates), a State monopoly charged with the exploration, management, and exploitation of the phosphates of Morocco.

May 1, 1930

By E. W. Dean

This report on the physical and chemical properties of typical crude oils of Oklahoma is the sixth in a series of preliminary chapters of a bulletin covering the producing districts of the United. States. Preceding reports* may be obtained on request. The details of the methods used in this survey in collecting samples, making laboratory tests, and interpreting results are discussed in the first three papers. If any errors or omissions are noted by readers, it is hoped they will be brought to the attention of the Bureau of Mines for correction before the appearance of the permanent report. Samples of Oklahoma crudes analyzed in this report were taken from those fields representing the major production of the State. The Oklahoma Geological Survey designates 172 different oil and gas fields in the State, S1 being in Osage County, 14 in Tulsa County, 14 in Okmulgee County, 9 in Washington County. The list of samples collected by the Bureau of Mines represents only 5 fields in Osage County - Bigheart, Burbank, Hominy, Osage Junction, and Pershing - yet these samples, together with those from adjoining fields, are representative of nearly all crude produced in the county. The sample &apos;from the Pershing field, for example, is representative of the crude produced in several fields in that part of the county - such as Nelagoney, Pawhuska, Wyomona - and the sample from the Skiatook,

Jan 1, 1922

By E. S. Shedd

Misch metal was electrowon from a treated bastnasite concentrate in a REF3-LiF-BaF2 electrolyte at 950° C. The metal was prepared and tapped from a 1,000-ampere cell, and nearly 100-percent utilization of the rare-earth oxide was achieved. Prolonged operation in a smaller cell (40 amperes) indicated that the composition of the misch metal product was reasonably constant, and no significant increase of impurities, with the exception of carbon, was noted.

Jan 1, 1970

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By H. J. Heinen

Excellent gold recovery was demonstrated in a laboratory-scale leaching test on waste material from an open-pit mine in northeastern Nevada. An injection system of leaching was applied in which the sodium cyanide solution was introduced into the interior of the dump at selected points. Dissolution of gold from the waste material, which assayed 0.06 ounce gold per ton, was readily achieved because the gold occurred as submicroscopic particles in a porous host rock. Gold recovery of 80 percent was obtained in 11 days from material crushed to 1 inch in size, and recovery was 90 percent after 21 days.

Jan 1, 1969

In the United States water pollution resulting from mining activities has long been recognized as a major environmental problem Mine drainage pollution results from many types of mining activities and includes both physical (i e , sedimentation) and chemical (i e , acidification, metal contamination, etc ) pollutants Active and abandoned surface and underground mines, mineral processing plants, mine and processing plant waste disposal areas, haulage roads, and tailing ponds are typical sources of mine related water pollution (130) One of the most serious pollution problems arising from mining activities is acid mine drainage resulting from the chemical reaction of sulfide minerals (commonly iron sulfides) and air in the presence of water Acid mine drainage is commonly associated with coal and hard rock mining areas in the United States In general the more serious and extensive acid mine drainage problems exist in the more humid coal regions east of the Mississippi River (11) In 1964 the U S Department of the Interior, Fish and Wildlife Service, reported that acid mine drainage adversely affected fish and wildlife habitat in 9,477 kilometers (5,890 miles) of streams and 6,062 hectares (14,967 acres) of impoundments in 20 states in the United States (64) Of the total affected waters, coal mining operations accounted for 97 percent of the acid mine drainage pollution reported for streams and 93 percent of that reported for impoundments In 1970 more than 19,308 kilometers (12,000 miles) of streams in the United States were reportedly significantly degraded by mining related pollution (130) Of the total affected kilometers, 16,920 kilometers (10,516 miles) or approximately 88 percent were located in the Appalachian coal region (Pennsylvania, West Virginia, Ohio, eastern Kentucky, Tennessee, Maryland, and Alabama) In addition, more than 965 kilometers (600 miles) of streams reportedly were degraded by coal mining in states in the Illinois, Western Interior, and Rocky Mountain coal regions The remaining portion of the stream pollution resulted from the mining of (1) copper (california, Montana, Nevada, New Hampshire, Tennessee, Virginia, and Wyoming), (2) lead and zinc (Colorado, Idaho, Kansas, Missouri, Montana, Oklahoma, and Tennessee), (3) uranium (Rocky Mountain States), (4) iron (Lake Superior iron region), (5) sand and gravel (all states), (6) phosphate (Florida and other states), (7) gold (Alaska), (8) bauxite and barite (Arkansas), and (9) molybdenum, gold, and other metals (Colorado) Abandoned mines and abandoned mine waste disposal areas contribute a large portion of the total pollution resulting from mining activities Numerous abandoned underground mines are located throughout the United States and many are discharging mine drainage pollutants In 1966 the U S Bureau of Mines estimated that more than 88,000 inactive and abandoned underground mines were in existance (126) A listing of these mines by state is presented in Table 1 0-1 More recent estimates indicate that this list is incomplete In Colorado alone there is

Jan 1, 1975

By M. B. Cooke

An analytical method for the determination of the gum-forming material in gasoline has been developed by the Bureau of Mines, during a study nor in progress to determine the best rays for elimination of such constituents from gasoline. This method is similar in principle to that previously described by Smith end Cooke,2 which involved evaporation of e sample of gasoline in a small glass dish. The evaporation was started on an actively boiling steam bath and completed in an air oven at 105°C. In the improved method described below, the stem bath has been replaced by a steam heated oven in which an inert atmosphere is maintained. Air is excluded from the oven, consequently the precision of the determination is increased. Furthermore, evaporating dishes different from those previously described may be used.

Jan 1, 1925