Search Documents

By Alla D. Mah

The heat of combustion of aluminum carbide (Al, C3 ) , obtained directly by combustion calorimetry , was AH298.15 -1,029.6 ± 1.9 kcal / mole . == The heat of formation of aluminum carbide corresponding to this value was AH298.15 = -53.4 ± 2.0 kcal /mole .

Jan 1, 1964

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992

By Edward F. Divers

A new nonclogging water spray system for continuous-mining machines has been developed under contract with the Bureau of Mines. This paper presents installation and operating guidelines for the system, which consists of improved and easily maintained machine-mounted hardware, including an inline Y-strainer, a hydrocyclone, a backup filter, and two quick-opening valves for flushing particulates from the strainer and hydrocyclone. Underground tests with continuous-mining machines have shown that when properly installed and maintained, the new sys tern virtually eliminates nozzle clogging and thus greatly reduces spray maintenance. The sys tern is relatively inexpensive and has been installed on typical continuous-mining machines for a total cost under $1,000.

Jan 1, 1976

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By Bruce K. Cantrell, Stephen W. Stein, David Hassel, Harvey Patashnick

The Mine Safety and Health Administration. Department of Labor, requires coal mine operators to measure compliance with federal re¬spirable dust exposure standards periodically using approved gravi¬metric samplers. However, the gravimetric approach, with its inher¬ent delays, cannot provide dust concentration data quickly enough to allow on-site correction of inadequate dust control strategies or re¬moval of personnel from harmful environments. Furthermore, alleged tampering with dust samples collected to determine compliance with standards prompted the Secretary of Labor to appoint a special Respirable Dust Task Group to study options to improve monitoring and control of respirable coal mine dust. The Mine Safety and Health Administration&apos;s Task Group recommended that the U.S. Bureau of Mines develop a fixed-site monitor that would provide continuous information to the mine worker and mine operator regarding dust levels and the status of compliance with the applicable respirable dust standard. In response to the Mine Safety and Health Administration&apos;s request, the U.S. Bureau of Mines is investigating several sensor tech¬nologies for continuously monitoring respirable coal mine dust. One of these technologies is the Rupprecht and Patashnick Co. tapered element, oscillating microbalance. The bureau is in the process of investigating the suitability of using this sensor in the high humidity and vibration environment of underground coal mines. Laboratory tests have indicated that, with modification, the sensor can meet the humidity and vibration requirements for underground coal mine use. Currently, the bureau is developing

By W. R. K. Wu

Studies are reported on the structure of coal and coke with the graphical , statistical densimetric method based on the relation between the molecular volume per carbon atom ( M / C ) and the atomic hydrogen - carbon ratio ( H / C ) . Previous work , mostly from chemical and physical investigations , is critically reviewed . Difficulties in evaluating the ring increment are demonstrated for coal and coke for the statistical densimetric method based on the additivity of atomic volumes of constituent elements . A new diagram is presented for the graphical method . Methods are introduced for correcting M /C and H/C for the presence of minor constituents in coal and coke . With the graphical method , the fractions of aromatic carbon atoms in the total carbon atoms are estimated for a coal , a resin , and 5 petrographic components ; the types of condensed structure in the fundamental units of molecules are discussed for these substances , 28 coals , and 6 " average " cokes at 500 ° to 1,000 ° C. It is also shown that the number of rings in the fundamental units of coal generally increases with increasing rank and that of coke , with increasing carbonization temperature .

Jul 1, 1960

By Stephen P. Holt, John A. Bowsher

A preliminary examination of the mica deposits in Culberson and Hudspeth Counties , Texas , was made in September 1942 by A. B. Needham, district engineer of the Bureau of Mines . The deposits were reexamined by R. C. Redfield , associate mining engineer of the Bureau in November 1942, at which time he was accompanied by Philip S. Hoyt , geologist , and J. C. Moore , foreman of the Texas Mica and Feldspar Company . Exploratory work was started on February 16 , 1944 , and terminated on April 30 , 1944. A crew of 4 to 10 men was employed under the supervision of the authors .

Feb 1, 1947

By B. D. Sartwell

Multiple-charged beams originating from a 300-kv ion accelerator are important tools in the study of metal surfaces and thin films. A knowledge of the particle range is necessary for an understanding of the interaction processes of the ions with the targets. Utilizing a theory developed by Lindhard for determining the range of low-energy ions in solids, the ranges of H, He, C, N, 0, and Ar ions in A1203, Al, Fe203, Fe304, CuO, Cu20, Fe, Cu, Sn, and W were calculated for the energy range 60 to 400 kev using a computer program written in BASIC. The range, presented in graphical form, is given in both µg/cm2 and angstroms. In addition, heavy ion ranges were calculated for comparison with published experimental values. For ions with Z > 5, the discrepancy between the calculated values and published experimental values generally ranged from 2 to 40 percent; the largest deviations were probably due to experimental error.

Jan 1, 1970

By W. C. Holliman

This second of a series of reports on the characteristics of commercial aviation gasolines presents inspection test data furni8hed on their products by 15 manufacturers of commercial grades of aviation gasoline and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data on 18 grade-80, 20 grade-91/98, 20 grade-100/130, and 9 grade-115/145 aviation fuels are presented. These gasolines represent July 1947 production.

Jan 1, 1948

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631&apos;s fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR&apos;s) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats&apos; attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By G. W. Jones

The determination of the ignition temperature of diethyl ether and ethylene in air and omen which is described in this report was made primarily for comparison with similar determinations of other compounds in the same apparatus and using the see laboratory technique. The investigation was conducted at the Pittsburgh Experiment Station of the United States Bureau of Mines with the cooperation of Merck & Co., Inc.

Jan 1, 1935

By W. J. Wenger

Oil fields in the Powder River Basin of Wyoming have produced 731 million barrels of petroleum through 1959. Production in 1959 was 32 million barrels, the highest production since 1924. The record production was in 1923, when the Basin produced 38 million barrels of oil and the Salt Creek field, then at its peak, produced 35 million barrels. In this report, the characteristics of crude oils found in the Basin are used as a basis for determining the best re-fining uses for the oils and for predicting the characteristics of oils that may be discovered in the Basin in the future. Analyses of 108 oils sampled over a period of 30 years are presented Crude oils of two major types are produced from the Powder River Basin. One has a low sulfur content and occurs in younger formations, and the other has a high sulfur content and occurs in older formations. The oils with low sulfur contents are generally light colored and waxy, and may be either paraffinic or naphthenic. The oils with high sulfur contents are usually dark colored and asphaltic; only their low boiling fractions are paraffinic. Alteration appears to account for the anomalous properties of some oils found at shallow depths. Shapes and slopes of correlation index curves classify the oils into the same two groups as their sulfur contents, with gently sloping curves representing the low-sulfur oils and steep curves representing high-sulfur, asphaltic oils,

Jan 1, 1961

By Liane L. M. Kadnuck

This report summarizes the results of a hydrologic research study conducted by the U.S. Bureau of Mines (USBM) in cooperation with Energy West Mining Co. at the Deer Creek and Cottonwood Mines, near Orangeville, UT. The USBM evaluated hydrologic and overburden failure data to assess the response of local ground water to underground coal mining in single-and multiple-seam conditions. Fourteen springs located over the two mines were investigated in the study along with overburden failure response caused by longwall panel extraction. Spring discharge was compared to climatic variation and time of undermining to quantify response to undermining. Spring discharge had been reduced owing to below-normal precipitation during the period evaluated. The response of springs to mining in the vicinity was influenced in part by the thick overburden present at the study site the presence of hydrophilic clays and mudstones in the overburden stratigraphy, and elevation of the springs above mine level, which buffered the effects of undermining.

Jan 1, 1994

By Keith A. Heasley, John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U. S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of are corded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with bump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip, etc.) of the failure of the strata surrounding the active and multi-panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

By T. Estelle Gardner, A. R. Taylor

Heat capacity measurements were made on sodium bromide ( NaBr ) and sodium iodide ( NaI) in the temperature ranges of 7 ° to 300 ° K and 56 ° to 300 ° K using an adiabatic calorimeter . Smooth values of heat capacity, entropy , enthalpy function , and free- energy function were calculated from the heat capacity data at 10° K intervals and at 273.15° and 298.15° K. Entropy and free energy of formation values at 298.15° K also were calculated for the two compounds using entropy values determined in this study and other data reported in the literature . The entropy values calculated at 298.15 ° K were 20.75 ± 0.06 entropy units (eu ) for sodium bromide and 23.55 ± 0.07 eu for sodium iodide .

Jan 1, 1964

Another major aluminum company announced intentions to follow other domestic producers recent price actions by raising its unalloyed ingot quotes by 3¢ to 44¢ per pound, effective June 1, 1976. COBALT: All final data for 1975 are included in the table for cobalt on page 23. Demand in March increased significantly for the second month in a row, signaling a recovery from the previous year&apos;s relatively low demand levels. Imports of cobalt tripled in March over those of February. This should partially offset reduced sales of cobalt excesses from the National Stockpile. Import projections for the next several months have been lowered because transportation difficulties in Zaire are expected to result in reduced shipments.

Jan 1, 1976

By J. E. Pahlman

Spontaneous oxidation and combustion of sulfides and resultant fires are serious problems in underground mines. The Bureau of Mines has con-ducted fundamental thermal gravimetric analysis (TGA) research to deter-mine the mechanisms and factors governing the rate of low-temperature pyrite oxidation, and to identify possible inhibitors to spontaneous oxidation and combustion. The mechanism of low-temperature pyrite oxidation was found to be topochemical, meaning that the oxidation process is controlled by the chemical reaction at the interface between pyrite (FeS2) and iron sulfate (FeS04)&apos; An activation energy of 8.9 kcal/mol FeS2 was obtained for oxidation of minus 500-mesh pyrite in an atmosphere of 60 vol pct water vapor and 40 vol pct . Water-vapor content of the atmosphere was found to be the critical factor in the rate of spontaneous oxidation of pyrite, with a water-vapor content greater than 20 vol pct needed for accelerated oxidation. An atmosphere of pure oxygen resulted in negligible oxidation. The rate of pyrite oxidation is also greatly affected by the particle size of pyrite. Pyrite-oxidation rate increased drastically for particles less than 40 ~m. Room-temperature pyrophoric behavior was observed for freshly ground unoxidized pyrite (55 pct minus 5 ~m) upon exposure to air. Addition of water-adsorbing materials such as activated alumina (Alz03) decreased the rate of pyrite oxidation.

Jan 1, 1986

By Nar S. Dalal, Xianglin Shi, Val Vallyathan

"INTRODOCTIONIn an earlier communication 1 from our laboratory it was reported that mechanical crushing of coal and quartz under normal air atmosphere generates of free radicals on the particle surfaces, and that these radicals decay with time, hence pointing to a higher toxicity of fresh dusts in relationship to pneumoconiosis and silicosis. More recently Fubini et al.2 have also reported the detection by electron spin resonance (ESR) of the formation of SiO. and Si-type of radicals from quartz particles crushed under atmospheric conditions. In agreement with earlier ESR studies on single crystals of quartz crushed under high vacuum ( -10-10 torr>3 and subsequent exposure to air,3 and to other gases,4 these radicals were identified2 as being formed by the homolytic cleavage of the Si-0-Si bonds and the reactions of the Si• and SiO- radical with atmosphere. Fubini et al.2 also suggested that these radicals might be involved in the mechanism of the fibrotic action by silica, either by transforming the particle surface into a selective oxidating agent or as an initiator of a sequence of reactions leading to fibrosis. Earlier Gabor and Anca5 bad reported that lipid ·peroxidation caused by free radicals on the silica surface might be involved in the red blood cell membrane damage. Thus far, however, no parallel cytotoxicity, fibrogenicity, and free radica1 studies on a given quartz dust sample have been reported, except for some earlier work from our laboratory.1·6·7 We now present more recent results obtained from parallel cytotoxicity, fibrogenicity, and free radica1 measurements on a freshly made quartz dust. The dust's free radica1 content was measured using ESR spectroscopy while its cytotoxicity potential was estimated via hemolysis. Hemolysis was employed as the toxicity test because it is a widely used method for estimating the potential of a dust for disrupting the cell membrane. 8 The fibrotic potential was followed by measuring the dust-induced lipid peroxidation, using linoleic acid as a model lipid. As discussed below, the results obtained suggest new clues to the mechanism of the quartzrelated cytotoxicity and fibrogenicity. MATERIALS AND METHODSReagentsCrystalline quartz particles with a size range of 0.2-2.5 mm were obtained from the Generic Respirable Dust Technology Center, Pennsylvania State University, University Park, Pennsylvania. These particles were crushed in air to obtain quartz dust samples with particle sizes smaller than 20 microns. We chose to work with a dust with mixed particle sizes, rather than a specific range, as an effort to simulate the mining atmosphere. An agate mortar-pestle arrangement was used for the crushing and grinding because of the close similarity of the structure of agate to that of quartz. Diethylenetriaminepentaacetic acid (DETAPAC) were purchased from Sigma. All other chemica1s were purchased from Fisher or Aldrich.Hemolysls ExperimentsHemolytic activity of silica was measured, following an established procedure,9 as the amount of hemoglobin released from a 2 % suspension of sheep erythrocytes after incubation with 10 mg of silica dust for one hour at 37 °C. The hemoglobin release was estimated via the absorbance at 540 nm using a Gioford spectrophotometer. The procedure was calibrated by substituting the silica dust by a phosphate buffer solution as a negative control (background) and O.S % Triton-X-100 as a positive control (100% hemolysis). The percentage of hemolysis was calculated as follows:"

Jan 1, 1990