Search Documents

By K. C. Dean

A flotation method was developed by the Bureau of Mines for concentrating pollucite, a cesium-aluminum-silicate mineral that may contain from 20 to 40 percent cesium oxide. Separation of the pollucite from three typical ores was achieved by froth flotation of the associated micas, feldspars, and other gangue minerals, using sulfuric and hydrofluoric acids and a cationic-type collector. A low-tenor, 8 percent cesium ore from Maine was upgraded to 20 percent cesium with recovery of 87 percent of the cesium. Relatively high- grade ores from Canada and Southern Rhodesia were beneficiated at lower ratios of concentration to 28 and 29 percent cesium content respectively with recovery of over 92 percent of the cesium. In addition to concentrating the cesium content of ores, the method also effectively separates cesium from sodium, potassium, and lithium, and in certain ores from rubidium. This is accomplished by selective froth flotation of the alkali metal-bearing gangue minerals such as lepidolite, other micas, and feldspars. Since the alkali metals, especially potassium and rubidium, are difficult to separate chemically or thermally from cesium to prepare high- purity cesium products, separation by physical mans is important.

Jan 1, 1962

By Milton H. Fies

The dedication of thin building, establishing a station of the U.S. Bureau of vines at the University of Alabama, bristles with significance and challenges the wisdom and courage of the people of this State. Here is united, in common aim, the Engineering School of our State University, recognized for its competency and usefulness, and the Federal Bureau of Mines. The Bureau is one of the most effective arms of our National Government. It outranks in accomplishment, measured by practical scientific contribution, any like governmental organization in all the other nations. It possesses none of the characteristics of many other bureaus of government which have created popular bias. Here is one Bureau devoid of political suggestion or aim with a personnel zealously devoted to labor in scientific re¬search - an organization marked by practical accomplishment, alleviating many of life's burdens, raking easier life's pathway, and unerringly pointing to life's possibilities.

Jan 1, 1936

The Mine Safety and Health Administration (MSHA) defines an independent contractor as "any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine." Contractors that perform specific types of work are required to report the number of employees who perform work at coal mines and at noncoal mines.

Feb 1, 2005

By Walter T. Lewiecki

Bauxite was first discovered in-the United States near Rome, Ga., in 1887, Approximately 400,000 tons of bauxite ranging from 46 to-62 percent alumina were mined in the area from 1888 to 1930. In February 1943, The Republic Mining & Manufacturing Co. installed a dryer and began mining and reworking dumps from the old bauxite mines. Some 3,000 long tons were dried and shipped to the chemical industries from March 1943, to June 30, 1943. In 1941 and 1942, representatives of the Bureau of Mined and the Federal Geological Survey/ visited this area and proposed an exploratory project that at first was to be confined to the Heritage district northeast of Rome (see fig; I). The Bobo district, southwest of Rome, was to be explored after work .1n the Hermitage district was completed. The Hermitage district comprises an area of about 50 square miles in the northwest quarter of Bartow County and the adjacent portion of Floyd County. It is bounded on the north by the Gordon County line, on the east by U. S. Highway 41, on the south by U. S. Highway 441, and on the west by State Highway 53.

Jan 1, 1949

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By Frank E. Federspiel

In 1986 and 1987, at the request of the U.S. Forest Service, the U.S. Bureau of Mines examined the 47,000-acre Electric Peak study area (part of the formerly-designated RARE II Non-wilderness Recommended Area no. 1609) to evaluate its' identified mineral resources. The study area is in Powell and Jefferson Counties, YT, about 30 mi southwest of Helena and 30 mi north of Butte. Three lode localities within the study area contain an estimated 159,000 tons of identified subeconomic resources containing gold, silver, and accessory lead, copper, and zinc. Resources at those localities range from 10,000 to 134,000 tons with grades ranging from 0.04 to 0.32 oz/ton gold, 0.92 to 16.42 oz/ton silver, 0.14 to 79.65 percent lead, and as much as 0.41 percent copper and 0.68 percent zinc. One property also contains 0.15 percent antimony. Gold, silver, and base-metal content in samples of poorly exposed mineralized structures indicate that further exploration may identify resources on seven additional study area localities.

Jan 1, 1988

By A. J. Martin

The Tri-State, or Joplin, zinc and lead mining district in south- western Missouri and adjoining, parts of Kansas and Oklahoma is one of the great mining districts of the world. It is in flat-lying or gently rolling agricultural country near industrial centers and coal, oil, and gas fields. The nearly horizontally, lying bedded rocks in which the ore bodies are found were originally limestone but are now largely chert containing minor percent- ages of dolomite and other minerals. The ore occurs in nearly vertical fis- sure zones, large and small, and in blanket (sheet-ground) deposits. The mining depth ranges from surface diggings to $50 feet. The average tenor of the ore mined, in recent years is much lower than that of ore produced in other large zinc and lead districts of the United States. Mining and mill- ing costs are low because of the shallowness of mining, amenability of ores to concentration, efficiency resulting from long experience of management and labor, and other factors. The operators comprise many small and medium-size producing companies and partnerships, as well as individuals and a few larger producers. About 7,000 men are employed in the mines and mills during normal industrial activity. The concentrates produced are sold f.o.b. the mill bins to local representatives of smelting companies at prices quoted on the Joplin market. The productive life of the district began with the discovery of lead near Joplin in 1848, but output was not large until after mining for zinc began near Granby in 1871. In most of the intervening years through 1945 the district produced more zinc than any other field, and it generally ranked third or fourth in the United States in lead production. Figures compiled from sources given later in this paper show a total output for the district from the beginning through 1945 of 20,755,020 tons of zinc concentrates and 3,334,057 tons of lead concentrates valued altogether at $1,110,058,581 in the mill bins. The output, in terms of recoverable metals, was 10,609,408 tons of zinc and 2,529,121 tons of lead, valued in all, at the average yearly market prices of the metals, at $1,691,282,419. During the 39 years (1907-1945) for which complete figures are available, the annual output of the district fluctuated from 23 to 66 percent of the total United States mine output of zinc and from 5 to 18 percent of the total lead; the averages for the period were 40 percent for zinc and 11 percent for lead. peak yearly production was attained in 1926, with an output of 423,800 tons of recoverable zinc and 102;117 tons of lead. Since that yoar the production rate has trended downward, accentuated at first by the depression in the thirties and later ameliorated somewhat under the stimulus of heavy demand and higher metal prices during World War II; the output in 1945 was 139,274 tons of recovorablo zinc and 23,556 tons of load. The above figures show the groat contribution made by the Tri-State district in the past toward the country's supplies of primary zinc and lead, cspecially zinc. However, the district's production is expected to decline both in quantity and in proportion of total United States mine output unless important discoveries are made. Ore exposed in mine workings and extensive exploratory drilling done in recent years within and without the productive The

Nov 1, 1946

The Pittsburgh (Pa.) and Spokane (Wash.) Research Laboratories are among the world?s foremost mining research establishments. Once a part of the former U.S. Bureau of Mines (USBM), which was abolished by the U.S. Congress in fiscal year 96, health and safety research at these laboratories was transferred to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is the Federal agency responsible for conducting research and making recommendations for the prevention of work-related illness and injury. The Institute is part of the Centers for Disease Control and Prevention within the U.S. Department of Health and Human Services. Over the past two decades, the Pittsburgh and Spokane Research Laboratories have produced sustained technological achievements in mining health and safety, including? ? Development of novel respirable coal dust control technologies and more effective monitoring techniques to reduce worker exposure to hazardous mine dusts. ? Improved ground control technologies to warn and protect miners from the dangers of coal mine roof collapses and other hazardous strata conditions. ? Improved ergonomic design criteria and training methods to protect mine workers from injuries and fatalities associated with equipment and manual tasks. ? Development of enabling technologies that allow miners to control their mining equipment from a physically safe, protected work area away from respirable dust, harmful noise levels, and roof collapses. ? Improved mine fire detection and extinguishment techniques. ? Development of smaller, lighter, and safer emergency breathing devices.

Jan 1, 2007

By Charles T. Baroch

RESEARCH strengthened the position of cesium as the preferred material (commonly but erroneously called "fuel") for ionic propulsion engines. Its use as an element of the plasma thermocouple for generating electricity also seemed more likely. Domestic Production.-No domestic ore of cesium and rubidium was produced. San Antonio Chemicals, Inc., San Antonio, Tex., and Maywood Chemical Works, Maywood, N.J., continued to produce cesium and rubidium compounds including carbonate, chromate, hydroxide, nitrate, sulfate, and all four halides. Rocky Mountain Research, Inc., Denver, Colo., began producing various cesium and rubidium salts. American Potash & Chemical Corp., Los Angeles, Calif., offered cesium and rubidium for sale.

Jan 1, 1960

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By John E. Urosek, Dennis A. Beiter, William J. Francart

In This Chapter [Designing bleeder systems Examining and maintaining bleeder systems Evaluating bleeder system effectiveness] INTRODUCTION Bleeder systems are that part of the mine ventilation network used to ventilate pillared areas in underground coal mines. Pillared areas are those in which pillars have been wholly or partially removed, including the areas where coal has been extracted by longwall mining. Bleeder systems protect miners from the hazards associated with methane and other gases, dusts and fumes, and oxygen deficiency that may occur in these mined-out areas. Effective bleeder systems control the air passing through the area and continuously dilute and move any methane-air mixtures and other gases, dusts, and fumes from the worked-out area away from active workings and into a return air course or to the surface of the mine. A bleeder system includes the pillared area (including the internal airflow paths), bleeder entries, bleeder connections, and all associated ventilation control devices that control the air passing through the pillared area. Bleeder entries are special air courses designed and maintained as part of the mine ventilation system. [This chapter focuses on the design, examination, maintenance, and evaluation of bleeder systems in underground coal mines.] The history of coal mine explosions in the United States is a reminder of the importance of adequate ventilation. Some of those disasters were the result of inadequately ventilated pillared areas. The importance of developing bleeder systems to ventilate these pillared areas and evaluating the bleeder system’s effectiveness is reflected in present-day federal regulations. For more information on bleeder systems, see Tisdale [1996] and Urosek and Francart [2002].

Jan 6, 2006

By R. E. Siemens

The Bureau of Mines sought to correlate the variation of structure-sensitive superconducting properties with microstructure in selected Cb-Hf alloys and to compare the experimental results with those predicted by the GLAG theory. Alloys in wire and rod form were evaluated by critical temperature, critical current, magnetization, resistivity measurements, and optical and electron microscopy. In the absence of an external magnetic field, the current carrying capacity of columbium was greatly reduced with addition of up to 85 wt pct Hf, but a large increase in Ic occurred for Cb-90 wt pct Hf. Favorable Ic-H behavior was observed in cold-drawn alloys containing 25 and 57 wt pct Hf. Correspondingly, a maximum in Tc occurred at 10-25 and 90 wt pct Hf. Four- or five-hour heat treatment at 600° C resulted in maximum Ic values and maximum hysteresis in magnetization. Dislocation pileup, polygonization, and fine precipitates, responsible for flux pinning, are listed in order of their effectiveness as pinning sites. Sites having an average separation of 1,500 to 3,000 A and a diameter of 1,000 A or less were most effective in influencing Ic-H and M-H behavior. The resistive critical fields increased smoothly to a maximum of 80 k0e between 60 and 65 wt pct Hf. Highfield, mixed state, reversible paramagnetism was observed in some alloys; however, the GLAG theory was in good agreement with experimental results for the majority of the composition range studied.

Jan 1, 1969

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

By Frank E. Cash

The information in this report covers the accident experience of the pebble-phosphate industry of Florida for 1935 and 1936, as well as the 5 years 1930-34, inclusive, statistics of which were published in Information Circular 69174/. The compilation and publication of such accident experience statistics enable the pebble-phosphate industry, as well as other industries, to consider relative hazards and to compare experience and thereby promote accident prevention.

Jan 1, 1937

By Robert Lee Stahl

Comprehensive field tests were made by the Federal Bureau of Hines at the Conda open pit mine near Soda Springs, Idaho, to determine whether surface geophysical techniques could be used to detect and delineate faults in phosphate deposits. The tests included seismic refraction, magnetometry, electrical resistivity, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling was the most effective method for diagnosing faults. The method is quick, inexpensive, accurate, and can be easily used by mining company personnel to detect and delineate faults.

Jan 1, 1975

By H. H. Schrenk

"One phase of the Bureau of Mines' work in the field of health and safety is the promotion of the use of safe, satisfactory, and reliable respiratory protective devices. To promote the development of such devices the Bureau has established schedules of minimum requirements for oxygen breathing apparatus3/ gas masks/, supplied-air respirators5/ (hose masks, airline respirators, and abrasive blasting helmets, hoods, or masks), and mechanical-filter respirators6/.Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules.As a prerequisite to such submittal, the Bureau requires a statement that the device is completely developed and of the design and material the manufacturer believes suitable for a finished marketable device; that the device has been subjected to inspections and tests such as described in the schedules, and that it met those requirements when tested by the manufacturer or his testing agency; and a. statement regarding the nature, adequacy, and continuity of control of the quality of the respirator. If the manufacturer can satisfy these requirements, and if the device, when tested by the Bureau, meets its requirements, a certificate of approval is granted by the Bureau of Mines. The approved devices bear distinguishing marks that indicate that they have been approved, the purpose for which they are approved, and the limitations of their use. If it is found at any time that approved devices purchased in the oven market and tested do not meet the requirements of the schedule, the Bureau may rescind that approval. Lists7/ of approved devices are published periodically for the convenient information of the public.Respiratory equipment may be divided into two main groups: (1). Those that afford protection by removing atmospheric contaminants and (2) those by which a respirable atmosphere from an uncontaminated source is supplied to the wearer.The devices that protect by the removal of contaminants may be divided into two subgroups: (1) Those that protect against gaseous contaminants and (2) those that protect against particulate matter. There may, of course, be combinations of these two.The devices by which a respirable atmosphere is furnished to the wearer also may be divided into two subgroups: (1) The self-contained type, by which the supply of oxygen, or material from which the oxygen can be generated is carried by the wearer, and (2) the hose type, by which air is supplied to the wearer through a hose or tube."

Sep 1, 1939

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,857 samples, representing the products of 103 companies. The samples were collected during June, July, and August 1955. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1956

By Robert E. Manning

At present, a need exists for more effective noise control in the coal-mining industry. In particular, new muffler designs with the required acoustic performance are needed for percussive pneumatic drills. Accordingly, the U. S. Bureau of Mines issued a contract to USS Engineers and Consultants to design a muffler capable of attenuating the noise from the air exhaust of a pneumatic drill. The specific objective of the contract was to design and deliver a prototype muffler that would attenuate the air-exhaust noise to 90 decibels on the A scale (90 dbA). The test drill used in this investigation was one used for roof-bolting purposes in coal mines. Using the combined approach of analysis by digital-computer program and experiment by simulated-noise tests, three prototype mufflers were designed and constructed at U. S. Steel Research. The mufflers consisted of a variety of resonator chambers and expansion-contraction chambers, and were of the following sizes: A muffler with a 3- by 5-inch elliptical cross section and about 8 inches in length. A muffler 5 inches in diameter and about 5-1/2 inches in length. A muffler 5 inches in diameter and about 10-1/2 inches in length. These mufflers were subjected to laboratory tests to determine their effectiveness in attenuating exhaust noise, mechanical noise, total drill noise, and simulated noise. All mufflers reduced the exhaust-noise level by about 25 dbA - from about 115 dbA without a muffler to below 90 dbA with a muffler - and thus were successful in meeting the contract objective. Field tests were conducted with the three prototype mufflers at U. S. Steel's Robena No. 4 Mine, and no icing problem was encountered. A fourth prototype muffler was designed to fit around the leg of the pneumatic drill. Tests showed that this kidney-shaped muffler also reduced the air-exhaust noise to below 90 dbA.

Jan 1, 1973

By Earl L. Hastings

Although the principal market for diatomite in the United States is in the East,4 production of the material is presently restricted to the West, because the deposits are larger, mining costs are cheaper, and the quality of product is better than that obtained from other domestic deposits. However, Tallahatta diatomite, occurring in Choctaw and Clarke Counties, Ala., has a freight rate advantage, which should encourage competition for those market that are now being supplied with the purer diatomites from the western deposits. For this reason, diatomite occurrences in the Tallahatta formation were examined by the Bureau of Mines and physical properties of samples from the deposit were determined to obtain additional data for use by any potential producer who wished to evaluate the material for its commercial possibilities. In 1894 K. M. Cunningham5 found that the buhrstone formation (now known as the Tallahatta formation) contained "siliceous shells of marine diatoms, radiolaria and foraminifera, thus being rather of the nature of tripoli or diatomaceous earth than of a true clay." Cooke6 and Semmes7 also reported the Tallahatta formation to be composed principally of diatomaceous earth with accompanying beds of sand, clay, and sandstone.

Jan 1, 1963