Search Documents

By R. V. Ramani

This volume, the first of a six volume final report, provides an executive summary of the research and results carried out under a grant from the U. S. Bureau of Mines on underground coal mine ventilation. Under the project, a mine ventilation simulator was developed. Sensitivity of leakage and friction factors on the total quantity and pressure requirements was studied. The simulator was applied to a new mine under development, and to an operating mine, to demonstrate the usefulness of the simulator in ventilation planning and in evaluating proposed changes to existing ventilation system. The titles of the other volumes are as follows: Volume II: Mine Ventilation Network Theory Volume III: User's Manual for PSU/MVS Volume IV: Sensitivity of Leakage and Friction Factors Volume V: Application of PSU/MVS to Ventilation Planning of a New Mine Volume VI: Application of PSU/MVS to the Analysis of Modifications to Existing Ventilation Systems

Jan 1, 1977

By D. B. Gawthrop

"One of the properties of an explosive, of interest to the user, is its ability to transfer detonation across an air gap to another explosive charge. This Property is of particular importance with permissible explosives used in coal mines, since they are relatively insensitive to detonation when compared to many of the commercial dynamites used in metal mining.An essential characteristic of an explosive is that it shall always be sufficiently sensitive to propagate detonation completely. An insensitive explosive constitutes a hazard because of (1) the danger of drilling into unexploded portions of charges of explosives which have partially misfired, and (2) the likelihood of a low order of detonation, or the burning, of all or part of the charge in a hole prepared for blasting. The latter condition not only usually produces large volumes of poisonous gases, but it is particularly hazardous in gassy or dusty coal mines where explosions may result.The Bureau of Mines and manufacturers of explosives determine the sensitivity of explosives to detonation over an air gap by means of a [(halved-cartridge gap test,"" for which the ends of the cartridges of explosive exposed to one another, are cut off. Since in blasting, the crimped ends remain on the cartridges used, this investigation has been made to ascertain the effect of the crimped paper ends on the distance detonation is propagated over an air gap as compared with the propagation distances obtained when the crimped-paper ends are removed."

Nov 1, 1932

By A. B. Needham

This report describes the exploration work done in 1941 in connection with the search for strategic minerals as authorized by the Strategic Materials Act approved by the President on June 7, 1939. It deals with the various manganese deposits and showings in the Tombstone mining district of Cochise County, Ariz. The exploration project comprised a study of the geology, mapping of the areas, and exploration of various mines and deposits by sampling old drifts, crosscuts, and scopes, supplemented by diamond drilling from underground stations. The Federal Government's manganese-purchasing programs have revived interest in occurrences such as the scattered deposits near Tombstone. Because of this, the Bureau of Mines project report on the Tombstone district, prepared originally in 1941 but not published, has been revised and now is being made public.

Jan 1, 1956

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

By Albert E. Long

Preliminary experiments conducted in 1949 with a few diamond bits in which the diamonds in the bit crowns were set in hard-vector directions indicated that a substantial saving could be effected when a high percentage of the diamonds were oriented in this-manner. It was realized, however, that many additional tests would have to be performed before a positive trend could be established and the possibility of coincidence eliminated. Therefore, a long-range series of experiments was planned to investigate various phases of the problems related to the orienting of diamonds in diamond bits. This report (the third in a series) 2/3 presents the information obtained from tests conducted to investigate more fully the effects of orienting high-grade drill bort in diamond bit crowns. In these tests, the drill bort were oriented in both hard-vector and soft-vector directions in the crowns of AX-size bits. Test drilling was done in a dike of saussuritized dacite porphyry similar to a fine-grained granite in hardness e drillability.

Jan 1, 1954

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By J. W. Paul

This circular is one of a series of papers4 on coal-mining methods and costs which are being prepared through the sponsorship of the U. S. Bureau of Mines for the purpose of presenting information on present mining methods and certain features which govern costs, safety, and conservation. The methods employed are influenced by natural local conditions with respect to the thickness, character, and dip of the coal bed, the nature of the roof and thickness of the overbearing strata, and the means employed for roof support and its control.

Jan 1, 1929

By Bryan F. Ulrich

If resin-grouted roof bolts are not installed correctly, mine roof reinforcement can be affected, and roof falls can result. A bolt installation variable that is readily controlled by the mine operator is annulus thickness. The objective of this U. S. Bureau of Mines investigation was to study the effect of annulus thickness variations on the integrity of 3/4-in-diam resin-grouted bolts. Forged-head test bolts, 2 and 1 ft long, were installed in concrete blocks that had been drilled with 1-, 1-1/8-, 1-1/4-, 1-3/8-, and 1-1/2-in-diam bits. Standard pull tests were performed; then the concrete was broken away from the bolts so that grout mix quality could be inspected. It was found that the optimum annulus thickness is 1/8-in (l-in-diam drill hole), and as annulus thickness increases from the optimum, there is a corresponding decrease in grout mix quality, effective grout ratio, and axial stiffness.

Jan 1, 1989

By Martin H. Rogoff

The presence of antibiotic materials extractable with polar organic solvents was demonstrated in coals of various ranks. Since these antibiotics occur in low concentrations, 200 pounds of a high-volatile C coal was extracted with acetone at room temperature to obtain sufficient material for detailed study. The biologically active materials in the extract were concentrated by extracting with aqueous sodium hydroxide. The fractions soluble in sodium hydroxide inhibited bacterial cultures when present in concentrations comparable to those at which other antibiotics are active (5 µg/ml). Steam distillation of the extracts did not yield highly active materials, contrary to the finds of other investigators. Mass spectrometry of the extract indicated, mainly, the presence of 6-ring compounds in the region of mass 324 to 392. The predominance of 3-ring aromatic systems found by ultraviolet analysis suggests compounds such as biphenanthryl or similar structures. The activity of the hydroxide- soluble material decreased markedly when the phenolic hydroxyl groups were transformed into trimethylsilyl ethers. Hydrolysis of the ethers yielded a product having the same activity as the original material, which indicates that phenolic compounds are largely responsible for the antibiotic activity observed.

Jan 1, 1963

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a 'cascading pillar failure' (CPF), occurs when one pillar in a mine layout fails, transferring its load to neighbouring pillars, which causes them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S.A. are documented. Mining engineers can limit the danger presented by these failures through improved mine design practices. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines-the containment approach, the prevention approach and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining at shallow depth. Cascading pillar failure {CPF) in room-and-pillar mines can go by many other names, such as `progressive pillar failure', `massive pillar collapse', 'domino-type failure' or 'pillar run'. In this kind of failure when one pillar collapses the load that it carried transfers rapidly to its neighbours, causing them to fail, and so forth. This failure mechanism can lead to the rapid collapse of very large mine areas. In mild cases only a few tens of pillars might fail; in extreme cases, however, hundreds, even thousands, of pillars can fail. CPF can have catastrophic effects on a mine, and sometimes these effects pose a greater risk to health and safety than the underlying ground-control problem. Usually, the CPF induces a devastating air blast as a consequence of the displacement of air from the collapse area. An air blast can disrupt the ventilation system totally by destroying ventilation stoppings, seals and fan housings. Flying debris can seriously injure or kill mining personnel. The CPF might also fracture a large volume of rock in the pillars and immediate roof and floor. In coal mines and certain other mines this can lead to the sudden release of large quantities of methane gas into the mine atmosphere; a methane explosion might result from the CPF. CPF is at the far end of the spectrum of unstable pillar failure. At the other end are slow `squeezes' that develop over days to weeks and, because of their slow progress, do not pose an immediate danger to mining personnel. There is ample warning time for men and machinery to get out of the way of the failure. In a CPF, however, the failure progresses so rapidly that men and equipment cannot be evacuated in time. Significant seismic energy is released as a consequence of the rapid failure and collapse. CPF should not be confused, however, with coal-mine bumps and rockbursts. In some cases the damage can appear similar, but the underlying mechanics are completely different. As will he shown later, the mechanics of CPF depend on the applied vertical stress and the post-failure, i.e. strain-softening, behaviour of the pillars. In a CPF pillars shed their applied load rapidly and have very little residual strength after failure. The collapse itself may release significant seismic energy, but otherwise the mine is seismically quiet. Alter a CPF the openings in the affected mine workings have usually closed completely. In contrast, coal-mine bumps and rockbursts occur in seismically active mines. Research has shown that coal-mine bumps and rockbursts are seismic events induced by mining that damage underground mine workings. Bumps and bursts are thus a subset of a much larger set of mining-induced seismic events.[ Only some of these seismic events damage mine workings; fortunately, most do not. The mechanisms by which a mining-induced seismic event can lead to a damaging coal-mine bump or rockburst is still a significant research area.2 After a bump or rockhursr the affected mine workings may or may not be completely closed. For example, in the coal-mine bump described by Soler and co-workers2 the mine workings remained open even though the pillars were destroyed during the bump event. Because CPF differs from a coal-mine bump or rockburst, the design approaches to control their occurrence also differ. The design recommendations developed here apply to CPF and not to bump- or burst-prone mines. Cascading pillar failure examples Unfortunately, CPF has occurred in room-and-pillar coal, metal and non-metal mines. The most infamous example is the Coalbrooke colliery in South Africa, where 437 miners perished where [si >1 3at1ttsumsus7car kky vArtMixiL7i nesafr tramwsamn ures] on 21 January, 1960.1 Table I summarizes the mining dimensions of 13 examples of rapid pillar collapse in U.S. coal mines. All occurred during the 1980s and 1990s, and all happened suddenly or without significant warning. Most resulted in air blasts and damage to the ventilation system. Table 2 gives the mining dimensions of six room-and-pillar metal and non-metal mines in the U.S.A. where failure occurred in all probability by the CPF mechanism. The collapse areas can be huge. Fortunately, some of these failures gave advance warning. At the lead-zinc mine slabbing from pillars and roof falls began four weeks prior to the main collapse.3 At the copper mine considerable rock noise and smaller failures preceded the main collapse by five days.5 At the copper-silver mine it is not known if nature provided a warning.6 Evidently, the trona mine collapsed without warning.7,8 Rock noise and other failure warnings preceded the silica mine collapse by three weeks. v The presence or absence of warnings at the salt mint is not known. to Most of these collapses induced a substantial air blast; damage to the ventilation systems was limited, however, to bent airdoors and a few downed stoppings, except at the trona mine where extensive damage to the ventilation system resulted.

By W. H. Blackburn

This paper describing the milling practice at the Tybo concentrator is one of a series of similar papers being prepared by the United States Bureau of Mines on milling methods and costs at the various mills in the United States. ACKNOWLEDGMENT A large part of this paper way prepared by H. M. Lewers, mill superintendent of the Tybo plant of the Treadwell Yukon Co., Ltd.

Jan 1, 1931

Real economic growth for 1988 may fall short of the 3.3% projected by the U.S. Department of Commerce in August 1988 be-cause the summer drought and intense heat in many areas curtailed output more severely than expected. The economy grew at an average annual rate of 3.0% for the first three quarters of the year, slowing in the second and third quarters. Export growth, which occurred even as the dollar edged up com-pared with other industrial country currencies, was an important factor in the expansion. Notable gains were posted in sales of machinery, computers, aircraft, chemicals, and telecommunications equipment. Imports increased, but not as much as exports, and the U.S. trade position was still much improved from that of 1987. Personal consumption expenditures grew slightly faster than the economy as a whole. Purchases of consumer durables showed notable strength in the first half of 1988, but slowed down in the third quarter. [ ] Despite the moderate rise in interest rates, business spending for new plant and equipment also rose and contributed to 1988 gross national product (GNP) growth. Both new business investment and export demand spurred orders for U.S.-made machine tools. Orders for machine tools for the first 8 months of 1988 were almost triple those for the corresponding period in 1987.

Jan 1, 1988

By Wilbur I. Duvall

Twelve millisecond delayed blasts in four limestone quarries in Iowa were instrumented with arrays of vertical velocity gages to determine if the direction of propagation through the rock or the method of initiation of the blast had any effect upon the level of vibration. Two gage arrays approximately 90° apart were used to test the effect of direction of propagation. The vibrations from blasts initiated by three methods were recorded. Vibration records from these tests were analyzed for peak particle velocity as a function of distance from the blast. The data are shown to fit a power Law equation. Direction of propagation is shown to affect the value of the exponent n. The effect of charge size per delay interval on the level of vibration is removed from the data by scaling the travel distance by the square root of the charge weight per delay period. The method of initiating the blasts is shown to have a strong effect upon the level of vibration and the spread in the data from one shot to another.

Jan 1, 1963

By Oliver Bowles

It is noteworthy that 80 to 95 per cent of the gross production of all slate quarries in the United States is discarded as waste . In view of the loss involved in handling so much waste , and the consequent added cost of the finished product , the Bureau of Mines has undertaken a study of the slate industry for the purpose of devising the best means of reducing the proportion of waste , and of utilizing the unavoidable waste . The utilization of waste has received special attention , and the cooperation of many prospective purchasers of waste slate has been enlisted in testing its adaptability for various uses .

Mar 1, 1921

By Fredrick L. Johnson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 25,640 acres of the 29,680-acre Devil?s Garden Lava Bed, 21,040 acres of the 28,660-acre Squaw Ridge Lava Bed, and 9,100 acres of the 12,600-acre Four Craters Lava Bed Wilderness Study Areas (OR-D01-D02, OR-001-003, and OR-001-022, respectively) in order to evaluate their identified mineral resources. The study areas are located in Lake County, OR, about 50 air miles southeast of Bend. No mineral resources were identified in the three study areas. The areas are almost entirely underlain by recent lava flows. Cinder cones occur in each of the areas; however, the best cinder occurrences are in the Four Craters Lava Bed study area. Slab lava, of facing stone quality, is scattered throughout the Devil?s Garden Lava Bed study area, and to a lesser extent, in the Squaw Ridge Lava Bed study area.

Jan 1, 1987

By A. B. Whitehead

A spectrographic method for the determination of 18 impurities in cerium is presented. The carrier distillation technique is utilized to separate the spectra of impurities from the complex spectrum of cerium. Metal samples are ignited to the oxide, mixed with silver chloride carrier containing an internal standard, and excited with a 20-ampere direct-current arc. An additional exposure, made after carrier depletion, provides for the determination of refractory elements. Experiments to determine the best carrier, sample-carrier ratio, electrodes, arc current, exposure conditions, internal standards, and any matrix effect are described. The relative standard deviation of the method at the 20- and 200-part-per-million levels is about 25 and 15 percent, respectively. The average relative error is about 20 percent in the 10- to 1,000-part-per-million concentration range.

Jan 1, 1962

By H. M. Smith

In studying the chemistry of lubricating-oil fractions from so-called ?paraffin-base? crudes, one of the first requisites is a method for the separation and removal of waxy material. A method utilizing solvents for this purpose is described in this report, together with preliminary experiments with solvents that led to its development. The solvents actually used are secondary butyl alcohol, acetone, and mixtures of these.. Isopropyl alcohol was also studied. Preliminary Experiments In previous work on "intermediate-base" crude oil, following the work of Wyant and Marsh acetone had been used for laboratory separations of oil and wax. Then acetone was tried for the separation of the waxes and oils of "paraffin-base" crude, the volume of acetone required (80 parts to 1 part of oil) was found to be too great for large-scale work. For this reason the effectiveness of other solvents was studied; the separation by acetone, however, was used as a standard.

Jan 1, 1927

By T. H. Jeffers

To help maintain an adequate supply of minerals to meet national, economic, and strategic needs, the Bureau of Mines investigated the feasibility of extracting copper from coarse native copper ore with ammoniacal ammonium carbonate solution by a simulated in situ leaching procedure. A 5.9-metric-ton (6.5-ton) sample of minus 30.5-centimeter (12-inch) conglomerate-type ore analyzing 1.96 percent copper was leached in a column for 556 days with a solu-tion that contained, in grams per liter, 2.2 NBs and 1.9 CO[3=]. The copper extraction was 71.4 percent, and reagent consumptions were, in kilograms per metric ton of ore, 1.1 NBs and 0.85 CO[3=] (in pounds per ton of ore, 2.2 NH3 and 1.7 CO[3=]). The pregnant leach solutions contained about 1.4 grams per liter copper, which was readily extracted from these low-tenor liquors with a 1:19 mixture of an organic extractant and kerosine. Copper was stripped from the loaded organic with depleted electrolyte containing 150 grams per liter H2S04, and the copper was recovered by electrowinning with antimonial lead anodes. Conditions also were established for minimal lead transfer to the cathode copper.

Jan 1, 1979

By R. L. Grant, R. W. Van Dolah, N. E. Hanna

An experimental investigation was conducted to assay the relation between natural gas concentration and ignitibility of the gallery atmosphere . Both the gas concentration representing maximum ignitibility and the relationship between certain properties of the explosives and their incendivity are discussed . The data show that variation in the natural gas content in the gallery can have a highly significant effect on ignitibility of the gallery atmosphere ; maximum ignitibility of the atmosphere by permissible explosives occurs with approximately 8.1 percent natural gas . The study also shows that incendivity of a permissible explosive cannot be determined only by its detonation velocity , oxygen balance , or ballistic mortar strength . However , for similar type explosives , trends observed indicate that their incendivity increases with detonation velocity or bulk strength . Additionally , for underoxidized explosives studied here , the more negative the oxygen balance the less incendive was the explosive within a class defined by salt content .

Jan 1, 1963

By Lon D. Santis

The Code of Federal Regulations Title 30, Parts 56, 57, 75, and 77 require that detonators and explosives be separated by four inches of hardwood or equivalents when transported together in mines. This standard was developed to protect the explosives from initiation by the more sensitive detonators. The research reported here is an attempt to quantify the fire protection offered by four inches of red oak and other materials. Boxes with a volume of 6.75 cubic feet were made from four-inch thick rough green oak (RGO), two-inch thick RGO plied, two-inch thick #1 common (dried) red oak plied, and a metal/plywood composite. These and boxes meeting the Institute of Makers of Explosives' (IME) Safety Library Publication No. 22 were tested in bonfires. The boxes were instrumented with thermocouples, filled with detonators, and placed over a kerosene fire imparting about 16 kilowatts per square meter heat flux for up to 3 hours. Tests showed that the wood boxes protected the detonators for over an hour with variations between the different trials. In the IME 22 container tests, detonators began exploding in as little as 17 minutes in one test and not for 2-/12 hours in another test. Detonators in the metal/plywood boxes began to explode in about 15 minutes but with minor alterations, were able to contain the detonators. The test results show that the exterior of an IME 22 container significantly affects its thermal properties. Defects in the form of cracks and the manner in which the container is closed have a significant effect on the performance of a detonator container in a fire.