Search Documents

By C. C. Shale

Electrical resistivities for various coal ashes in air and in a nitrogen atmosphere are given over the range 100° to 1,500° F. Resistivity of low-carbon ash in air is very high at low temperature, rises to a maximum at about 250° F, decreases very rapidly with increasing temperature to about 800° F, then decreases gradually to approach an asymptote at 1,500° F. Resistivity of high-carbon ash in air follows this same general trend at values which are much lower and are proportional to the carbon content. After the carbon has been burned off, resistivity of the remaining ash approaches the high values corresponding to low-carbon ash of similar chemistry. Two factorial experiments show the effects of temperature, particle size, chemical content, and compressibility on the resistivities of four fly ashes of widely different chemical composition in the temperature range proposed for coal-fired turbines. Resistivities of all low-carbon ashes tested fall in the range 106 to 107 ohm cm at 1,500° F and should be removable by electrostatic precipitators. Ashes containing carbon in excess of about 8 percent, however, have low resistivity (as determined in nitrogen), especially at high temperatures. Therefore, high-carbon materials may not be collectable in precipitators because the resistivity is below the minimum value necessary for precipitation. Consequently, high carbon residues from partial combustion of coal probably could not be removed effectively at high temperatures.

Jan 1, 1968

By L. H. Kalenowski

The metal lithium, its alloys, and its salts are becoming Increasingly important as industrial materials. Lithium metal, because of its great affinity for elements, such as nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, has become important for a wide variety of uses, ranging from purifying helium gas by removing the nitrogen to scavenging molten metals of undesirable impurities. The excellent fluxing properties of lithium salts have found increasing use in such applications as fluxes for welding aluminum and in lower melting ceramic glazes and coatings. Lithium chloride is one of the most hygroscopic salts known and is widely used as a dehumidifying agent. .About 17 lithium minerals are known. Four of these have commercial importance: Amblygonite, lepidolite, zinnwaldite, and spodumene. Spodumene is the most important source of lithium and lithium salts at present, but sizable deposits of amblygonite occur in the pegmatite area of the Black Hills of South Dakota. The size and nature of these deposits preclude the, possibility of, any assurance of an adequate supply of amblygonite for an operation processing only this mineral. Frequently spodumene and amblygonite occur associated in pegmatite minerals. Preliminary investigations indicate that a simultaneous recovery of spodumene and amblygonite can be made by froth flotation. A single process for treating spodumene and amblygonite or mixtures of thorn, would make possible more use of amblygonite as a source of lithium and obviate the separation of spodumene and amblygonite when they occur together.

Jan 1, 1952

By S. R. Borrowman

This investigation by the Bureau of Mines was undertaken to develop information on the extractive metallurgy of thorite ores because potential ore bodies of this mineral have been found recently in Colorado, Idaho, and Montana. Basic information on thorite ore treatment that would be useful in appraising the potential of these and other domestic thorium resources was developed. The work was done mainly on thorite ore containing 3.87 percent ThO2 from the Powderhorn district, Colo., and on a composite sample containing 0.52 percent ThO2 from the Wet Mountains district, Colo. Limited tests of d corroborative nature subsequently were made on a sample containing 2.30 percent ThO2 from the Lemhi Pass area on the Idaho-Montana border.

Jan 1, 1962

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By D. W. Frommer

The investigation reported in this paper is one of several included in a broad program of developing new or improved concentration processes for the oxidized and partly oxidized deposits of lead and zinc, A sample from the Playter lease, Newton County, Mo., containing pyromorphite was successfully concentrated by fatty acid flotation to a grade of over 62 percent lead. Owing to the presence of a high content of slime-size values, the overall recovery of lead at that grade was limited to 44 percent. DESCRIPTION AND HISTORY OF PROPERTY The mineral pyromorphite is a chlorophosphate of lead containing 76.4 percent lead, and, although it occurs frequently in association with other lead minerals, it is considered a minor ore mineral of lead. The manner of occurrence of oxidized lead minerals, including pyromorphite, which frequently are no larger in grain size than the clay with which they are found, militates both against development of a simple beneficiation process and high recovery. The profitable exploitation of such deposits depends not only on a successful treatment procedure but a highly favorable metal market as well. For these, and perhaps other reasons, very little research has been done on the recovery of pyromorphite from its deposits.

Jan 1, 1956

By R. V. Ramani, C. B. Manula, A. Owili-Eger

Recently, a collection of programs that will simulate a ventila¬tion system with extensive analyses and report-generating capabilities and error diagnostics has been developed (Didyk, 1974). It has pro¬visions to handle air injections, methane or gas emissions, and leakage. Additionally, it will solve problems where fixed and/or maximum air quantities are specified for some airways. Finally, the simulator has been structured to be extremely modular so that additions and revisions to the model can be easily made. The general aspects of the information flow and logical structure of the mine ventilation simulator are shown in Figure 14. The output from the methane emission model is input into the ventilation simulator for calculation of the concentrations in all branches of the network. The methane model and the ventilation simulator provide powerful tools for the analysis and planning of mine ventilation systems. INPUT DATA REQUIREMENTS In all of the mathematical models, several coefficients that de¬fine the characteristics of the ventilation system are used. For the ventilation simulator, these include the frictional characteristics of the ventilation regulatory devices. Considerable work has been done on the experimental determination of these coefficients for smooth pipes and well-defined mediums, but only limited data are available for actual mining conditions. FRICTION FACTORS: The frictional characteristics of mine airways affect both the dispersion of pollutants and air flow through the roadways,. They

Jan 1, 1975

By J. C. Johnson, W. G. Pariseau, D. F. Scott, F. M. Jenkins

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 1993

By A. M. Dale, J. Standeven, B. Evanoff

We encountered several areas of methodologic uncertainty during development of a data collection method for use with vibrating hand tools in metal assembly. A local manufacturer sought our assistance designing a data collection method for evaluating and predicting risks of upper extremity disorders associated with use of vibrating hand tools. Current methods of vibration measurement are described in ISO 5349 [2]. However, the complexity of measuring vibration along with other exposures such as force and posture has limited the number of workplace-based studies of upper extremity disorders that have included direct measurements of vibration. Data from this preliminary study was used to look at two issues: a comparison of vibration values between production and non-production workers when performing the same task, and a comparison of worker ratings of vibration comfort to direct measurement of tool vibration. Methods Eight experienced production workers used each of six metal fastening tools to install fasteners. Vibration was collected by 3 tri-axial accelerometers, one attached to the tool handle following ISO 5349 recommended locations, one attached to the hand dorsum on the 3rd knuckle and one to the thumb side of the wrist. Data sampling rate was 10,000 samples/second. Hand grip and feed forces were obtained using a Novel pressure sensing mat on the palm. Each trial consisted of installing 10 fasteners per tool for each of the 6 tools. The test set-up placed the wrist in the position typically used by the operator during production. Each worker documented subjective comfort and effort ratings on a seven point scale following each series of fastener installations. One series of testing was completed by three non-production workers inexperienced in fastener installation to simulate use of alternative employees for data gathering. Vibration data for each trial were acquired, digitized, and stored using Lab View. The X, Y, & Z axes were used to calculate the vector sum response for each tri-axial accelerometer. The tool data were digitally filtered following ISO recommendations. Calculated data consisted of the mean RMS over the tool’s on- time, the starting and breaking peak impulses, and the peak of the frequency response. Results Production workers (n=8) were right hand dominant males with a mean age of 55 years and normal hand strength (mean right grip = 106 lbs). Non-production workers (n=3) had similar characteristics. We found large and statistically meaningful differences in hand force during tool use between production and non-production workers (mean production workers = 9.77 lbs, mean non-production workers = 43.30 lbs, p = 0.0001). Vibration values obtained from the hand also showed a statistically meaningful difference (mean in production workers = 0.67 Gs, mean in non-production workers = 1.48Gs, p = 0.0014, figure 1). Experienced worker ratings of comfort during tool use demonstrated a moderate correlation with measured vibration (r=0.63). Worker ratings trended with direct recordings from the tool handle as shown in figure 2.

Jan 6, 2006

Provide low-cost fire protection for big bulldozers. Approach A fire protection system, previously used on mobile logging equipment and adapted to surface coal augers, has now been adapted for use on large mining bulldozers. How It Works Heat sensors mounted in the engine compartment and hydraulic hose areas detect the fire, usually before the operator does. This causes the system to automatically discharge A-B-C class dry chemical extinguisher through a fixed piping system. The system can also be manually activated from either the opera-tor's cab or ground level. Location of the principal components of the system are shown in the drawing The heat sensors of the sys-tem consist of bimetallic strip switches which operate at about 10000F temperature. Switch operation results in release of compressed gas from a small storage cylinder. The gas expands to blow the dry chemicals out of the nozzles, in a spray that lasts about 15 seconds. The compressed gas used is usually nitrogen, although carbon dioxide is also used.

Jan 1, 1978

By F. E. Joyce

This paper describes the development of a process for producing manganese and iron pellet concentrates from low-grade manganiferous iron ores of the Cuyuna range by a two-stage sulfatization-reduction roast. First, the manganese minerals (7.5 percent manganese) were converted to water-soluble manganese sulfate by roasting in sulfur oxide gases at 700° C, then, the hematitic iron minerals (31 percent iron) in the hot sulfatized are were reduced to magnetite with simulated reformed natural gas in the temperature range of 350° to 425° C. Batch tests were made in a 3-inch-ID by 6-inch-long, gas-heated, stainless steel retort, and continuous countercurrent experiments were performed in a 2-inch-ID by 10-foot-long, electrically heated shaft furnace. Manganese sulfate was removed from the roasted product by leaching with water, and over 90 percent of the manganese was recovered in an oxide product (65 percent manganese) obtained by precipitation, drying, and thelmal decomposition of the sulfate. An iron oxide concentrate (60 percent iron) with an iron recovery of 75 percent was obtained from the water-insoluble residue by magnetic separation.

Jan 1, 1973

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous flotation tests of weathered mica pegmatite ores from Alabama and North Carolina to determine the technical feasibility of recovering commercial-grade mica concentrates. A new anionic-catonic method was developed for recovering mica in the presence of clay slimes. In continuous tests, concentrates containing 98.1 percent mica were obtained from the Alabama pegmatite ore; the North Carolina pegmatite ore concentrates contained 97.2 percent mica. The recoveries were 83.8 and 81.6 percent, respectively.

Jan 1, 1965

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By Jr. Reed

Cassiterite was discovered in Coosa County, Ala. in 1880 by Judge John S. Bentley. Since that time intensive surface prospecting has revealed the presence of cassiterite in pegmatite bodies that occur in a zone about 20 miles long and 3 miles wide. Numerous trenches and test pits and several shafts were sunk, and one attempt was made to nine and concentrate the cassiterite commercially. The problem of a domestic tin industry and the question of the extent of the Alabama tin deposits have long been of public interest and concern. The deposits have been examined by numerous geologists and several governmental agencies, including the Geological Survey of Alabama, the Geological Survey and the Bureau of, Mines. of the Department of Interior, and others. The Bureau of Mines and the owners of the properties, Charles A. Dean and Robert A. Russell, investigated the Coosa County tin deposits under a cooperative agreement from October 1, 1948, to June 10, 1949. Sixteen hand trenches totaling 527 linear feet and 33 machine trenches totaling 6,780 linear feet were dug. Two shafts wore sunk for a total of 72 feet, and 44.4 feet of drifting was done. Thirty-one diamond-drill holes totaling 2,776 feet were drilled.. Four hundred thirty samples, representing 1,192.6 linear feet, were taken for assay and wore analyzed by the Southern Experiment Station at Tuscaloosa, Ala.

Jan 1, 1950

By A. L. Murray, D. Harrington

From 1870 to the end of 1929 the coal production of Utah has been some- what less than 110,000,000 tons. During this period at least three major disasters have occurred with fatalities totaling about 380, establishing a decidedly bad record of approximately 3.5 persons killed by major mine explo- sions per million tons of coal produced. Even during the period when there have been no disasters, such as the years 1914 to 1920, inclusive, the fatalities in ordinary working were about 5.4 per million tons produced, against 3.7 per million tons for the whole United States for the same years. The 5-year period following the World War, 1918 to 1922, inclusive, had 4.7 fatalities per million tons; hence, the fatality record in the coal mines of Utah has uniformly been in excess of the average of the coal mines of the entire country. Notwithstanding this poor record, Utah has given to the coal-mining world many excellent safety methods and practices, and Utah coal mines in general take greater measures toward safe mining than do the coal mines of any other State; if practices and methods allowed and pursued in coal mines of other States were tried in Utah coal mines, there would be a succession of disasters.

Nov 1, 1931

To develop a safety training module for surface miners and road construction workers exposed to the hazards of highwalls. Background Investigators collaborated to develop a new training module that would address the hazards of working around highwalls. Such a module would be applicable to surface mines and road construction sites, both of which require personnel to work under and on top of steep and often unstable slopes.

Aug 1, 2004

By Spangler Ricker, F. T. Johnson

"SUMMARYThe Ione-Carbondale clays area is 2 miles northwesterly of Ione, Amador County, Calif. It was explored during the war by the Bureau of Mines to obtain data on the alumina content and to recover representative samples for beneficiation tests for alumina recovery.Seventy holes, aggregating 8,837 feet, were drilled, and about 10.3 acres of land was cleared of underbrush. Maps and cross sections were compiled showing location of holes, analyses, and other pertinent data.The clay beds vary in thickness from 13 to 196 feet, and are covered by a loose overburden, averaging about 11.9 feet in thickness. The ratio of overburden to clay is 1 : 8.2. Analysis of a composite sample showed the recoverable alumina (A12O3) and Fe2O3 content to be in the order of 23.6 percent and 2.8 percent, respectively.Topography of the clay area is ideal for open-pit mining methods and plant site.INTRODUCTIONInvestigation of alumina-rich clays for the possible production of aluminum was made during the recent war period, when the shortage of bauxite was becoming critical.Results of field examinations by the Bureau of Mines and the Federal Geological Survey indicated that one of the most promising areas for the development of alumina-rich clays is in the Ione-Carbondale district."

Mar 1, 1948

By W. E. Miller, John Campbell, W. P. Yant, G. W. Jones

"Because of its interest in accident prevention, the U.S. Bureau of Mines cooperates with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground openings and in developing means for preventing such explosions. For several years this Bureau has been cooperating with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co. in detecting and eliminating combustibles and physiologically harmful gases in manholes in the city of Boston and adjacent territory.These Bureau of Mines investigations° have shown that combustible gases from the usual sources — leakage from gas—distributing systems and from underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas, which are termed here ""soil"" gases, also occur in manholes and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric changes affect their production and passage into the manhole space. These gases appear to be produced by bacterial and fermentation or through reactions of entrapped air in the soil. Soil usually abnormally high in carbon dioxide and low in oxygen, and contain varying amounts of methane. They are especially clangorous to men entering manholes because they lack sufficient oxygen to support life. Owing to the difficulty of constructing gastight manholes the most feasible method for eliminating soil gases from manholes is by ventilation. Consequently the Bureau of Mines initiate 4 study of natural ventilation methods for the removal of these gases from manholes and also for taking care of unforeseen accumulations of combustible gases and vapors.The following factors were considered by the Bureau to be important to the natural ventilation of manholes: (1) Relation of area of ventilation opening* to the capacity of the manholes, (2) size and shape of the manhole, (3) design of the ventilation opening (4) and velocity, and (5) weather conditions."

Jun 1, 1936

By Joseph Cervik, Maurice Deul, Albert Sainato

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pct; reductions of 38 to 79 pct were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No. 3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By Clarence O. Babcock

This report describes the results of a Bureau of Mines investigation in which an elastic inclusion, orebody, or mining system is replaced for purposes of analysis with an imaginary effective inclusion of rectangular shape that encloses the region. This effective inclusion has averaged physical properties that are directly related to the average inclusion stresses. The results were in excellent agreement with those predicted by Donnell's theory (2)2 for an isotropic elliptical inclusion in a state of plane strain for all height-to-width ratios and for all degrees of inclusion hardness from very soft to very hard. The results are exact for an isotropic circular inclusion and provide an easy method of evaluating the stresses obtained by cylindrical inclusions in boreholes when the Poisson's ratio for both host and inclusion equals 0.25 for plane strain or 0.333 for plane stress. The theory was also used to predict the average stresses in 48 finite-element models of single transversely isotropic inclusions of ovaloid and rectangular shape. An interesting and useful observation from this work was that the forces on elliptical inclusions in the x and y directions, produced by applied uniaxial stresses in the y and x directions, respectively, were equal in magnitude but opposite in sign when the applied stresses were equal. This occurred when the plane strain condition was used with a Poisson's ratio of 0.25. The practical usefulness of the method is given by treating a variety of mining problems: (1) The average stresses in an orebody of irregular shape; (2) the average stresses in single-level room-and-pillar mining systems; (3) the average stresses in multiple-level room-and-pillar mining systems; (4) the effect of mining sequence on the average stresses produced during mining; (5) the stresses in cylindrical borehole plug related to host rock stresses as a function of plug hardness; and (6) methods for simplifying finite-element analysis of complex structures.

Jan 1, 1974

By Robert C. Steckley

The Bureau of Mines performed a fragmentation experiment in cooperation with Duval Corporation in a porphyry copper-molybdenum deposit near the Sierrita pit south of Tucson, Ariz. This experiment evaluated the fragmentation created in a 10-hole test blast having blasthole spacings of 25, 20, and 15 feet. The 10 blastholes were 9 inches in diameter and contained a total of 17,400 pounds of aluminized slurry blasting agent in 50-foot columns with 60 feet of stemming. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. These core examinations included study of length recovery, rock quality designation (RQD), weight recovery, and size distribution. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the broken material on the surface. Fragmentation to depths of 110 feet was excellent from the 15-to 20-foot blasthole spacing patterns. Good breakage was also produced by the 25-foot pattern although the effects of the blast were not so obvious. In situ leaching tests were not conducted. However, based only on size consideration, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1975