Search Documents

By Lloyd A. Morley, Robert Stefanko

This report has presented a literature review of explosion proof¬ing of coal mine electrical equipment. The international "state-of¬the-art" is an extremely difficult definition to quantify but, from the preceding paragraphs, it is evident the international community be¬lieves that it is represented by the International Electrotechnical Commission's Publications. Five questions were set forth during the beginning of this report. Each will be evaluated in light of the preceding discussion. 1. Can Schedule 2G specifications on explosion-proof containers be substantiated? Literature was found in the three main problem areas, surface temperature, mechanical strength, and explosion transmission, to determine this. Surface temperature requirements are adequate except for equipment that can normally overload, and the required intern¬al pressure does afford some margin of safety. However, in terms of safety, gap dimensions are about ten times smaller than that needed. 2. Is it possible to replace the Schedule's design requirements with performance specifications? Two primary areas were determined as mechanical strength and explosion transmission. As was mentioned, for present flange and gap standards, the 150 psig requirement is adequate. Furthermore, it is the authors' opinion that the level cannot be re¬duced if the present gap requirements are retained. The Schedule now requires that 16 tests be run, but the literature suggests that only from three to six examinations are necessary. Then by using the abso¬lute maximum pressure from these measurements or 150 psig, whichever is

Jan 1, 1974

By Launa Mallett

This paper introduces a method for teaching workers to communicate necessary information when giving or receiving emergency warning messages. Research has shown that when an emergency occurs, people may not get the information they need to take appropriate action. Interviews conducted with 48 underground coal miners who had escaped mine fires revealed that the warning information provided was inadequate. In some cases, sufficient information was not provided to the endangered miners. At other times, miners failed to ask for information they needed to plan and execute effective escapes. Researchers from the NIOSH Pittsburgh Research Laboratory have been studying the content of emergency warning messages and have developed an emergency communication protocol. A training intervention that presents the protocol and related mental cues is being evaluated for effectiveness in improving the content of emergency messages. In this paper the protocol is presented and the training package described. The evaluation procedures and a summary of the analyses conducted to-date are also provided. The training package was developed for use with underground coal miners, but could easily be modified for emergency communications training in other settings.

Jan 1, 2000

By Robert W. Freedman

The Bureau of Mines investigated methods of analysis of free silica in respirable dust, including both work done at the Bureau of Mines and work done elsewhere. The review covers both coal dust and noncoal dust, taking into account both existing and proposed chemical and spectroscopic procedures.

Jan 1, 1971

By W. D. Kaiser

Recent legislation and expected future legislation is aimed at reducing the dust levels developed in underground coal mines. Several techniques for reducing dust levels are being evaluated. One of these is the modification of cutting parameters such as feed rates, cutting speeds, and pick configurations in order to reduce the amount of dust generated. In order to evaluate the feasibility of modifying cutting parameters to reduce dust, the Bureau of Mines commissioned Battelle to construct a small scale mining machine which could be used for evaluating the effects of those changes in cutting parameters. Specific features of this machine were that it should be highly instrumented to measure various cutting parameters, should have a wide range of feed and speed controls, and it should be possible to vary the pick configurations and geometries on the machine. In addition, it was desired that this machine should have cutting capabilities which greatly exceed present coal mining practice and also that the unit should be small enough and portable enough that it could be taken into and out of operating coal mines with a minimum of interference with the normal coal mine operations. The first step in constructing a machine to meet these requirements was to determine the cutting forces and approximate sizes of components which would be required to cut at the speeds and feeds specified by the Bureau of Mines. Initial calculations using; published data on cutting forces indicated that cutting forces in the neighborhood of 5,000 lbs and power levels of approximately 30 horsepower would be adequate for the application. However, further data developed during the course of the project indicated that when low efficiency picks are used, cutting forces and powers can be two to three times as high as these initially estimated values. After several design iterations, a design was chosen in which the cutting head was driven by four hydraulic motors which were part of a hydrostatic transmission which, in turn,

Jan 1, 1973

Occupational illnesses are more difficult to identify than on-the-job injuries. Many illnesses related to occupational exposures may not be diagnosed until years after exposure; by that time, exposed workers may have changed jobs or left the workforce. Other approaches to identifying occupationally related illness are analysis of death certificate data (see chapter 2) and medical examination studies of workers known to have high exposures to hazardous agents. Figures 5-1, 5-3, 5-4, 5-6, 5-8, and 5-10 show, for each commodity, the percent of illness conditions reported to MSHA by nature of condition. Heart attacks that occurred on the job are reported without regard to work-relatedness. Figures 5-2, 5-5, 5-7, 5-9, and 5-11 show rates by year during 1986-1995 for selected conditions. Since there are many limitations on the accuracy of illness reporting, the frequencies and rates shown here should not be considered directly comparable across commodities. Figure 5-12 shows estimates for hearing loss by age among coal miners compared to a nonoccupationally noise-exposed population. These data come from a study by Franks [1996] of a group of audiograms obtained on coal miners by a commercial company. Using the NIOSH definition of hearing impairment, i.e., an average hearing threshold level for both ears that exceeds 25 dB at frequencies of 1,000, 2,000, 3,000 and 4,000 Hz, the figure shows that by age 30, more than 10% of miners suffer hearing impairment; by age 50, 90% of miners have hearing impairment. In contrast, only 10% of the nonoccupationally noise-exposed population suffer hearing impairment at age 51, and 50% of the nonoccupationally exposed population have hearing impairment at age 69. Figure 5-13 shows a similar analysis of commercial audiograms on male metal/nonmetal miners [Franks 1997]. At age 20, approximately 2% have hearing impairment using the NIOSH definition of hearing impairment described above. This increases to 7% at age 30, 25% at age 40, and 49% at age 50. In contrast, only 9% of the nonoccupationally noise-exposed comparison population have hearing impairment at age 50. Franks' analysis showed a different pattern for female metal/nonmetal miners; they developed hearing loss at the same rate as would be expected for a non-noise-exposed female population.

Jan 5, 2000

By Andrew M. Leszcykowski

In 1985 at the request of the Bureau of Land Management, personnel from the U.S. Bureau of Mines examined a 27,680-acre portion of the 30,420-acre King Hill Creek Wilderness Study Area (10-19-2) in order to evaluate the mineral resources. The study area, in southwestern Idaho, is underlain by Tertiary tuffs and basalt. There are no known mining claims or prospects in the study area, and no mineral resources were identified. The Volcano mining district is immediately north, but mines there are in granitic rock which does not crop out in the study area. Oil and gas leases were offered for land in the southern part of the area, but no applications were filed, and the lease offering was withdrawn (1985). INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the King Hill Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978

By Oliver C. Fursman

The Bureau of Mines undertook this investigation to study methods of utilizing red mud residues from production of alumina from bauxite. Pilot-plant tests were conducted using Jamaican and Surinam red muds. Both the carbon-lime-soda sinter process and electric-arc smelting with coke and limestone were employed to recover iron and alumina. Alumina recoveries of 85 to 90 percent were obtained by the sinter process; although iron recovery was about 80 percent, the magnetic product was finely divided and difficult to separate from the gangue. Smelting red muds in the electric-arc furnace produced a pig iron with 98-percent recovery of iron; up to 84 percent of the A1203 was recovered by leaching the calcium aluminate slag with Na2C03 solution. A titania product assaying 96 percent TiO2 was recovered from the nonmagnetic portion of Surinam red mud sinter by extraction with H2SO4. Leached calcium aluminate slags and brown mud (from the combination Bayer process) are possible raw materials in the manufacture of portland cement.

Jan 1, 1970

By Robert King

Splicing portable trailing cables used in underground coal mines is usually less expensive in terms of capital outlay and production time lost than replacing them. However, handling trailing cables may result in electrical arcs, shocks , and burns. Also, destructive forces encountered during a mining operation may shorten the effective life of a cable splice. This report gives the results of an analysis of cable splice defects in an effort to establish cable splice performance criteria, determine testing standards for cable splices, establish guidelines for training programs in cable splicing, and indicate areas for improvement.

Jan 1, 1975

By D. Harrington

Research in connection with occupational diseases, including silicosis or, more definitely, pneumoconiosis, has been prosecuted much more actively in North American countries during the past 5 or 10 years than in any other known period. This applies particularly to the United States, owing largely to the fact that in recent years compensation for ill health presumed to be caused by industrial work of certain kinds is being paid to a far greater extent in this country than previously. Most other countries have had occupational-disease laws for many years. Court rulings in the United States, which started 5 or 6 years ago, have given a few heavy verdicts in connection with ill health or death caused, or alleged to have been caused, by some phase of occupational work other than traumatic injury, and these have called attention to the fact that ill health and even incapacitation can be caused by some kinds of employment. With the onset of the world-wide financial depression, which resulted in permanent abandonment of many business or industrial enterprises (among them mines) in the United States, the workers frequently believed that they could expect nothing in the future from their former employers, hence they felt free to demand monetary benefits or damages because of ill health which they suffered, or thought they suffered, because of their previous employment. The result was a flood of lawsuits and. compensation claims for occupational disease, particularly where dust was involved.

Jan 1, 1938

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By Mark Sheppard

[Considerable research work hi been done on secondary crushing and coarse and fine grinding, and the literature on the general subject of Crushing contains many references to the work of investigators on the laws governing end the factors entering into the economical production of fine materials. However, little information on primary crushing in available The literature deals mainly with problems and practices in ore dressing, end in this field the engineer or investigator is concerned largely with the production of fine material and the unlocking of minerals in the ore. Under such conditions close control of screen sizes of primary-crusher products is a secondary consideration and has received very little attention.]

Jan 1, 1938

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

By Jack C. White

The Bureau of Mines, in its efforts to insure the continued viability of the domestic minerals economy, has been engaged for several years in research on the extraction of alumina from domestic, nonbauxitic resources. Hydrochloric acid leaching of kaolin is one of the more promising technologies being studied for recovering alumina for feedstock to existing aluminum smelting capacity; 93 pct of this feedstock is currently imported either as bauxite or alumina. Organics contamination of pregnant leach liquor, originating during solvent extraction for removal of iron from aluminum chloride solution formed during hydrochloric acid leaching, causes rapid deterioration of the semihard rubber lining of process equipment. These organics were removed by a skimming tank-coalescer-activated carbon adsorption system. Organic levels of less than 10 ppm from the coalescer and less than 0.5 ppm from carbon adsorption were achieved. Analytical methods employing CC14 extraction and infrared spectrophotometry were developed to determine the organic content of both the liquor and the carbon. Mass transfer zones delineated in the carbon columns provide adsorption data for the design of larger systems.

Jan 1, 1981

By C. E. Jordan

Domestic cobalt resources are relatively large, but low grade. The full potential for cobalt production from domestic sources is at least 19.4 million lb of cobalt per year exclusive of offshore resources. A summary of the cobalt processing technologies for the major domestic resources is presented in this Bureau of Mines report. The processing technologies for the Blackbird, Madison Nine, Duluth Gabbro, iron ore pyrite, laterites, and manganese sea nodules are nearly complete, but the economics are not favorable. Research on these resources should be limited to approaches that promise to cut the total processing costs by at least 50 pct. The most promising sources of cobalt are the spent copper leach solutions and siegenite from the Missouri lead ores. Research on cobalt processing from these two sources needs to be completed.

Jan 1, 1988

Improve the health and safety of underground mine workers by finding ways of keeping them away from unsupported areas of the mine. Background Roof falls have been the leading cause of fatal accidents in the underground coal mining industry. During 1985-89, 92 coal miners were killed by falls of roof and rib, with more than 4,000 miners injured. According to accident investigation reports from the Mine Safety and Health Administration, 47% of the victims of these fatal roof fall accidents were in the area of unsupported roof al the time they were killed. There is an urgent need to find out why miners go under unsupported roof and to devise strategies for preventing this unsafe behavior. Approach To discover what can be done to prevent miners from going under unsupported roof, confidential interviews were conducted with 297 miners who work in the face crews of 6 different coal mines. The interview topics included company policies and actions regarding going under unsupported roof, how foremen react to people who go under unsupported roof, circumstances likely to cause some people to go under unsupported roof and how to prevent these situations, and observations concerning those who go under unsupported root.

Jan 1, 1991

By J. A. Eisele

As part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines has studied the removal of iron from simulated aluminum nitrate leach liquors by solvent extraction. Iron must be removed from aluminum nitrate liquor produced by leaching calcined kaolinitic clay with HN03 to reduce the iron level in alumina to less than 0.02 wt-pct Fe203 for use in reduction cells. The parameters reported are for (1) extracting iron from a feed containing 1.5 g/l Fe with di(2-ethylhexyl) phosphoric acid (EHPA), (2) stripping loaded organic phase with 20-pct HCI, and (3) water washing of loaded and stripped organic phase. Recommended operating conditions are two extraction stages using 15 vol-pct EHPA in kerosene and three stripping stages using 20-pct HCI. Results are also given for tests using other extractants and stripping agents.

Jan 1, 1982

Provide a means of recovering precious metal values from finely ground tailing materials. Approach Determine the procedures needed for agglomerating the finely ground material for subsequent heap-leach cyanidation of the precious-metal-bearing tailings. Applying Agglomeration/Heap-Leaching to Fine Tailings Agglomeration technology was developed by the Bureau of Mines to provide cost-effective recovery of precious metal values though better heap leaching of clayey or low-grade ores. While many precious metal producers have adopted this technology to reclaim precious metals from crushed ores and wastes, other operations have experienced problems in using the heap leaching technique effectively on piles of fine tailings. In contrast to the coarser ore and waste material, most tailings piles contain more than 50 percent minus 200 mesh materials with no coarse material. Fine particles and clays present in the pile can impede 8 uniform flow of the leaching solution through the heap, thus preventing efficient and cost-effective precious metals recovery.

Jan 1, 1986

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982