Search Documents

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By Walter O. Snelling, C. G. Storm

Although descriptions of the methods of analysis of explosives are to be found in many books on explosives, and in works on engineer- ing chemistry or chemical analysis, most of these descriptions are incomplete and lacking in details. The methods of analysis employed in the laboratories of most explosives factories are frequently treated as trade secrets, and very little information is published from such laboratories. This bulletin outlines the methods of analysis that are used by the Bureau of Mines in the examination of certain classes of explo- sives. The present form of most of these methods has been worked out in the bureau's explosives laboratory. The methods employed by Prof. C. E. Munroe were taken as a basis, and were elaborated to meet the demands incident to the treatment of complicated mix- tures and to the development of the explosives art. A subsequent bulletin will discuss the methods of analysis of "permissible" explosives, many of the latter being of decidedly complicated char- acter and requiring special treatment. This bulletin presents the methods of analysis of "ordinary" dynamite, and the ammonia, gelatin, low-freezing, and granular dynamites, and the common grades of black gunpowder and black blasting powder. The bulletin is published by the bureau for the information of all persons inter- ested in explosives and their safe and efficient use in mining work. As the term "ordinary" dynamite, though much used, has no conventional meaning, and may be used to cover a wide variety of compositions of matter, it may be noted that the standard dynamite used at the Pittsburgh testing station is a good example of the "ordinary" dynamite known in this country. This testing station dynamite has the following composition:

Jan 1, 1913

By George S. Koch

The distribution of gold in part of the Getchell mine, Humboldt County, Nev., is presented through the statistical analysis of 956 assays of rock cuttings from wagon-drill holes. Two methods to predict grade in undeveloped parts of the ore body are evaluated, and the possibility of sampling bias is tested. The distribution of gold is compared with that in three other Nevada gold deposits of the same type characterized by gold particles mostly of submicron size associated with carbonaceous rocks, and also with that in deposits with coarse-grained gold. Usually, fewer samples of a given type are required to make a satisfactory grade estimate for submicron deposits than for coarse-grained deposits. The economic consequence is that submicron gold deposits are likely to be less expensive to sample and evaluate than coarse-grained deposits.

Jan 1, 1970

By P. H. Floyd

Laboratory test work has shown that the Germania ferberite-scheelite ore can be concentrated to an acceptable grade. A ferberite concentrate assaying 66.9 percent tungstic oxide was made, with a recovery of 75.4 percent. A second concentrate of ferberite and scheelite was made assaying 54.2 percent tungstic oxide. Final beneficiation of combined rougher gravity concentrates was accomplished by roasting, magnetic separation, sulfide flotation, and retabling, to give a final ferberite-scheelite concentrate of 66.2 percent tungstic oxide, with a 91.1-percent recovery. INTRODUCTION This presentation covers the results of laboratory beneficiation tests conducted on tungsten ore from the Germania Consolidated Mines, Inc., by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg. This mining property is near Fruitland, on the southern edge of the Spokane Indian Reservation, Stevens County, Wash. The Germania district produced tungsten concentrates before and after World War I; interest is being renewed in the district because of the metal shortage.

Jan 1, 1954

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

By S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By T. F. Mitchell, J. A. McAllister, S. J. Hussey

"INTRODUCTION During the Bureau's extensive program of investigating possible domestic sources of manganese, an are-dressing study was conducted in its laboratories at Salt Lake City, Utah, on a sample of oxide manganese ore representative of vein material from the Ophir Hill mine at Ophir, Tooele County, Utah. The sample (obtained by blasting down and mixing a portion of the vein) was submitted by the Ophir Development Co. of Ophir, Utah. As the ore was too law in grade to be acceptable for direct production of ferromanganese, it was tested to determine its amenability to concentration by ore-dressing methods.At the beginning of the investigation of manganese-ore beneficiation in December 1940, the only product marketable to Metals Reserve Company was ferrograde manganese, grade B, the requirements for which follow: Mn, min., 48 percent; Fe, max., 7 percent; Si02, max., 10 percent; P, max., 0.18 percent; A1203, max., 6 percent; Zn, max., 1 percent.Later, the specifications were modified gradually. As of May 15, 1943, manganese products were acceptable if they contained over 35 percent manganese and less than 3 percent zinc and 1 percent phosphorus. Prices were based upon material containing 48 percent manganese, 6.0 percent iron, and 11 percent silica plus alumina. Premium were paid for manganese content in excess of, 48 percent and iron content below 6 percent, penalties being imposed upon products containing less than 48 percent manganese or more than 6 percent iron or more than 11 percent silica plus alumina. The specifications for commercial manganese further required that maximum particle size be 12 inches and that 75 percent of the product be coarser than 20-mesh. Therefore, fine material, such as table and flotation concentrates, had to be nodulized or sintered. In addition, carbonate manganese ores were not acceptable unless calcined."

Oct 1, 1947

By John E. Pahlman

The U.S. Bureau of Mines has continued its investigation of chemical additive drilling fluids that produce a zero surface charge (ZSC) on a rock to better define the boundary conditions of the phenomenon. Laboratory drilling tests were performed on Minnesota taconite, Tennessee marble, and Sioux Quartzite using diamond-impregnated coring bits or tungsten carbide spade bits. Drilling fluids were made from chemical additives such as inorganic salts, cationic surfactants, cationic polymers, acids, or nonionic polymers in either distilled, deionized water (DDIW), mine pond water, mine well water, or tap water. These additives were tested below, at, and above their respective ZSC concentrations. Penetration and bit life improvements obtained with ZSC concentration solutions ranged from 88 and 56 pct, respectively, to over 650 pct and over 400 pct, respectively, for the additives tested. Polyethylene oxide (PEO) was found to be the best additive for ZSC-controlled drilling because a continuous range of PEO solution concentrations produced the enhanced ZSC-controlled drilling performance.

Jan 1, 1989

By Ludwig Schmidt

Investigations conducted by the Bureau of Dines pertaining to the reduction of evaporation losses of petroleum have shown that such losses may be reduced 70 to 80 per cent by the use of vapor-tight tanks equipped with vacuum and pressure relief valves, and vapor-tight thief hitches. Additional studies have shown that it is often economical to supplement this type of construction with other measures that will reduce evaporation losses still further. Water-cooling systems, insulation, and light colored paints are the measures most often used in connection with vapor-tight tanks. Painting with light colored paints probably is employed in the greater number of cases. On account of the cost of insulation, or of installing water cooling systems, the use of these methods are restricted to tanks containing gasoline or crude petroleum with a very large content of low-boiling fractions. The effect of cooling systems has been discussed in a previous report.2 In choosing paints for tanks many factors must be considered. Probably the three most important are cost, protective value, and color. Many companies have adopted a standard color for all of their tanks in this way they reduce the initial cost of paint by buying in large quantities. The tank farms of such companies usually have a neat appearance, resulting from the uniform painting of all tanks. This procedure also has advertising value. Unfortunately, most of the paints used to protect steel are of the darker colors, usually red or black. These colors accelerate the rate of evaporation. Several companies have solved this difficulty by using a dark colored metal-protective paint as a primer coat, and a paint of any desired color for the final coat. Special metal-protective primers to be used under light-colored cover coats have been placed on the market by several paint manufacturing companies.

Jan 1, 1925

By Charles B. Kenahan

Application of ultrasonics in the electrolytic deposition of metallic manganese and manganese dioxide from sulfate electrolytes had several effects. Ultrasonics produced finer-grained deposits of electrolytic manganese at all current densities than obtained in normal cell operation, but at high current densities it resulted in less adherent deposits. Ultrasonic radiation did not affect cell voltage or cathode current efficiency. In the electrodeposition of manganese dioxide at 70° C., ultrasonic-; increased the current efficiency and decreased the cell voltage at a current density of 9 amperes per square foot, but it had little effect at current densities above this. The decrease in cell voltage was caused by the depolarizing action of ultrasonics at both anode and cathode. Ultrasonic radiation produced a smooth, glossy, adherent, and pit-free deposit at all current densities and at each temperature. Radiation had no effect on current efficiency or cell voltage at 90° C. Ultrasonics was more effective than conventional agitation in producing all of these effects.

Jan 1, 1962

By L. A. Haas

The feasibility of removing sulfur dioxide by carbon monoxide reduction in a fixed-bed catalytic reactor was investigated by the Bureau of Mines. The reduction rate of sulfur dioxide with carbon monoxide was significantly dependent upon the iron and alumina content of the mixed catalyst. Maximum catalytic activity was obtained with about 40 percent iron-alumina mixture with a nominal gas mixture of 10 percent carbon monoxide, 5 percent sulfur dioxide, and the balance nitrogen. The synergistic effect of this catalyst mixture was explained by a dual reaction site mechanism, with both iron and alumina augmenting their specific sites at their interparticle contacts. The catalytic activity also increased with decreasing catalyst pellet size. With O.7-mm pellets, the entire pellet appeared to be catalytically active in a 2-gram catalyst bed. The apparent activation energy of the reaction was 18.3 kcal per mole in the temperature range of 350° to 600° C. Carbonyl sulfide (COS) was produced by the interaction of carbon monoxide and sulfur. The amount decreased with decreasing CO concentration. The ratio of COS formed per SO2 removed reached a maximum at about 400° C. The reaction rate appeared to be independent of S02 concentration in the range of 0.2 to 16 percent. The rate, however, increased directly with the CO concentration in the range of 5 to 20 percent. The presence of CO2 (<15 percent) had no appreciable effect on the rate. However, not over 0.5 percent oxygen could be tolerated. This method appears feasible for removing S02 from waste gas if the oxygen is removed prior to the catalytic S02 reduction process.

Jan 1, 1971

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By David C. McHuron

The U. S. Bureau of Mines in their continuing research into sealants, selected MBAssociates to design, build, and test equipment and evaluate sealant as to its effectiveness is shale degradation. There were 20,050 sq.ft. of coal mine roof sprayed with a mine sealant and as a result, it has been estimated that the sealant coated roof has from 50% to 95% less roof falls than that roof which was not coated with sealant.

Jan 1, 1980

By John B. Umhau

[This !m-i~!.al survey giver, statistice.1 data res;?~dirf ~:rimay ard ?eco~- dqr or scmn tin used in thL: United St,ztas by industries an? incluclcz d;ta on stop&apos;ics, ~urchares, ard plnrt losr.c.5. It is :i ml:anwe of consq~tion in terms of fir.is1icd -prcd.~cts nz6.e iry initid ti11 Sabric:,.torc,, that is, aon- cerns that purchzse virc,in zni s~col~d&apos;l~y i.i.5 ti:; 01&apos; tin c;cra.. rav materi,als ar,d co:lrrert them into !ror?ucts such F!: ti:i plz.te, ~lloyr;, and. c?hemic?ls; comy~nias ;~urchn.&apos;.ii~; alloys, ch:rr.ic,~l::, or tin vl?.tc fcr furthcr a:mflzc- ture ?rc: ~-.f>t i~ci~~dcd. Tilit r~lqe:;tionrr::ire submit tod to consunern ar,nt:incd no dofinition of rnr.oncl.:ryr me$.-i; but, ovrirq to ti~i-: a~counti~ procedure used s.l~o~c-:t 1&apos; thu scrnn hac i~-.rtergol:e ch?rri?~ of ovinerzhip or titlo, thc rc!coverod t! n !its b~en i-c<;,r(it.!rj L.S r,e~3r;d:q met.1. Tbv tin content ~f ]

Jan 1, 1938

By T. A. Raczek

Materials for stronger ventilation tubing for underground use in hardrock mines were developed. The new material composites were evaluated in performance characteristics and compared to currently used materials. The materials were compared on tear, tensile, puncture and flammability properties. Based on cost versus performance data, a polyester film bonded to a polyester fabric was selected as the candidate material for field testing. Ventilation tubing fabricated from the selected material was field tested in two underground uranium mines for four-month periods. The test results indicated that the new composite showed an increase in useful life in the majority of applications, However, the cost performance ratio was not significantly improved to warrant commercialization of the product. When connected directly to some blowers, the material in close proximity to the blower deteriorated. However, material which was punctured or torn by mechanical means did not have further propagation of the tear. The high tear strength of the material prevented further damage. Improved methods of repairing inflated ventilation tubing were investigated and developed. All the repair methods were portable and self-contained. Repair kits based on adhesives, pressure sensitive tapes, and mechanical means were evaluated. Plier staplers and patch systems based on pressure sensitive adhesive proved to be most functional.

Jan 1, 1980

By Thomas J. Peters

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 7,000 acres of the 9,240-acre Little Blitzen Gorge Wilderness Study Area in Harney County, OR, to evaluate its mineral resources. The study area is dominated by a 1,500-ft-deep canyon that was carved by Pleistocene glaciers in gently westward-dipping homoclinal flows of Miocene Steens Basalt. The Bureau reviewed pertinent literature and county mining records During the field investigations, 18 rock samples were collected from basalt dikes, breccia, fractured or porphyritic flows, and 20 alluvial samples from gravel accumulations. Mercury anomalies from sampling by the Oregon Department of Geology and Mineral Industries could not be verified. The mercury might have originated -From the Pike Creek Formation, a known mercury-producing unit that may extend into the study area beneath the Steens Basalt. Any epithermal deposit at depth would be expensive to explore and develop.

Jan 1, 1986

The Tenth International Conference of Directors of Safety in Mines Research was held in the United States from September 28 through October 2, 1959, at Hotel Webster Hall, Pittsburgh, Pa. The Conference was organized by the Federal Bureau of Mines. In accord with the program outlined at the Ninth Conference (1956, Heerlen, Holland), the papers submitted dealt with the following three subjects: 1. Safety of coal mine explosives 2. Explosion hazards in mines 3. Ignition and fires in mines Seventy papers were presented. There were eight technical sessions followed by an extended tour of the Bruceton facility of the Bureau of Mines on October 2. Simultaneous translation was provided in the three official languages of the Conference--English, French, and German.

Jan 1, 1962

By Don] [Hinkle

Unable to Load

Jan 1, 1977